Advance Metro Logy- Unikl Msi
-
Upload
rudyee-faiezah -
Category
Documents
-
view
222 -
download
0
Transcript of Advance Metro Logy- Unikl Msi
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 1/9
Advance Metrology (Group 6)
Lab work 4
1.0 INTRODUCTION
From this task we are able to perform dimensional measurements such asangle, radius, and distance measurements, the contour tolerancing functionfor evaluating "form" and the report creation function for outputtingmeasurement results in a specific format are provided as standard,measuring both ease of operation and powerful analysis capabilities.Contour measurement using a contracer machine (Mitutoyo CV – 3100) isa powerful system for automatic high-volume measurement. Event withgreater precision in all axis for difficult stationary contour testing inproduction environment or in the test room.
2.0 HISTORY
3.0 OBJECTIVES
This practical task will be applied when to measure contour of part. It will beused to interpret our knowledge and understanding of the theories and
techniques discussed within the topics into our practical application. At thisend of this practical task, we are able to identify the method used tomeasure contour of part and we also able to demonstrate the operation of the ‘contracer’.
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 2/9
Advance Metrology (Group 6)
Lab work 4
3.0 RESOURCES & FACILITIES
a. Contracer CV-3100
b. Arm and Stylus
c. Rotary Vices
d. FORMPARK software – 1000
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 3/9
Advance Metrology (Group 6)
Lab work 4
4.0 Machine Specification
• Motorized z- axis
• Digital of recording of measurement value in Z1 and X axes
• Including FORMPARK measurement and analytical software
• Feed inclination adjustment ±45º
• ABS scale in Z2 axes
5.0 SPECIMEN/SAMPLE
Specimen 1 Specimen 2
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 4/9
Advance Metrology (Group 6)
Lab work 4
6.0 Methodology
a. Switch ON Computer and Machine power supply
b. Clamp the specimen to vicesc. Click to “FORMPARK contour” softwared. Create New File for new measuremente. Align the stylus to the specimen. Make sure the stylus in middle position
of Stylus Arm.f. Set the length of measurement ( up to 50mm). then click button X0, Z0
at left hand side column bar.g. When ready, press Start button and wait the stylus reading the contour.h. After the machine complete reading contour, make the measurement
for the drawing.i. Create line measurement: Line, tangent line, perpendicular, parallelline.
j. Create circle measurement: Circle (multi-points, range, center andradius)
k. Create position, difference: Coordinate difference, true position judgment
l. Create distance, angle: Distance, groove length, step, pitch, distancereference, angle
m. From this software we also can calculation, statistics: Arithmetic
calculation, absolute value, square root, maximum value, minimumvalue, mean, sum, standard deviation, unbiased standard deviation,area.
n. Editing of measured points: Deletion, translation, rotation, mirror image,o. positioning, combination, separation, projection
p. Sub-part program: Calculation procedure can be registered as a Sub-
part program. The Sub-part program can be integrated into a part
program facilitating measurement of batch of speciment
q. After complete the measurement, measured data and analysis
procedure can be saved in the hard disk or we can print out the result.
This function allows an original result report to be created and printed
out.
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 5/9
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 6/9
Advance Metrology (Group 6)
Lab work 4
8.0 Discussion
From this task, we can see that Contour measurement is very helpful in
precision measurement. Contour measurement can give accurate
measurement even in small dimension to the largest part.
9.0 Suggestion
• Increase the value measurement of X-axis up to 100mm
• Enlarge the work table (vice clamp) for larger specimen.
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 7/9
Advance Metrology (Group 6)
Lab work 4
10.0 Conclusion
At the last of this task, we are able to know which machine is suitable
to use measure the correct parts. From what we learn we know thatContracer Motutoyo CV-3100 are using to measure dimension of
small parts, and from this task also, we also know the limitation of this
contour measurement machine.
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 8/9
Advance Metrology (Group 6)
Lab work 4
UNIVERSITI KUALA LUMPUR
MALAYSIAN SPANISH INSTITUTE
ADVANCE METROLOGY
SPD 35103
LAB WORK REPORT
(LW4: Contour Measurement – Contracer)
Lecturer: MADAM WAN FARADIANA
8/9/2019 Advance Metro Logy- Unikl Msi
http://slidepdf.com/reader/full/advance-metro-logy-unikl-msi 9/9
Advance Metrology (Group 6)
Lab work 4
Group members:
MUHAMMAD SYAFIQ B. SAHARUDIN 54138207252
FAIZAL B. AHMAD RADZI 54137208305
NUR ZARITH SYAHIRAH BT. SENU 54137208341
RUDI HARTONO BIN ABDULLAH 54138208184
MOHD HARIS BIN JANTAN 54138208174