Administrator’s Guide Wireless IP Phone...

WLAN600

Wireless IP Phone Administrator’s Guide

Trademark Acknowledgement

All brand names are trademarks or registered trademarks of their respective companies.

Disclaimer

This document is supplied by BCM Communication Co., Ltd. No part of this document may be reproduced, republished or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording or through retrieval systems, without the express written permission of BCM Communication Co., Ltd.

BCM Communication Co., Ltd. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. BCM Communication Co., Ltd. Assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or mask work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. BCM Communication Co., Ltd. Makes no representation or warranty that such application will be suitable for the specified use without further testing or modification.

October 2004, Rev: 2.2

2

Declaration of Conformity according to FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority

to operate the equipment.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter

This EUT is in compliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and

had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement

C.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter

3

Contents 1. Introduction ...................................................................... 5 2. Getting Started................................................................. 6

2.1. Package Contents..................................................................... 6

2.2. Installing and Removing the Battery........................................ 6

2.3. Charging the WLAN600............................................................. 7

2.4. Keypad ...................................................................................... 9

2.5. Turn On/Off the Power ............................................................ 10

2.6. Load Default IP Address ......................................................... 10

2.7. Enter Administrative Mode ..................................................... 10

2.8. Locking & Unlocking the Keypad ........................................... 11

2.9. Adjusting the Speaker Volume ............................................... 12

2.10. Selecting the Character Mode................................................ 12 3. Configuring Network Environment ..................................13

3.1. Network Configuration ........................................................... 13 3.1.1. Fixed IP ....................................................................... 13 3.1.2. DHCP ........................................................................... 14 3.1.3. PPPoE .......................................................................... 15

3.2. Wireless Configuration ........................................................... 16 3.2.1. Wireless LAN Settings ................................................ 16

3.2.1.1. Wireless LAN ...................................................................................................................................16

3.3. SIP Configuration .................................................................... 19 3.3.1. Registrar IP Settings................................................... 19 3.3.2. Outbound Proxy Settings ............................................ 20 3.3.3. SIP Proxy Server Settings........................................... 21 3.3.4. Setting up the User Account ...................................... 22

3.4. Using the Phonebook.............................................................. 23 3.4.1. Searching Phonebook Entries - Edit Entry ................. 23 3.4.2. Searching Phonebook Entries - Erase Entry .............. 24 3.4.3. Searching Phonebook Entries – Speed dial Entry ...... 25 3.4.4. Adding a Phonebook Entry ......................................... 26 3.4.5. Erasing Phonebook Entries - One By One................... 27 3.4.6. Erasing Phonebook Entries - All ................................. 28

3.5. Call History ............................................................................. 29 3.5.1. Missed Call.................................................................. 29

4

3.5.2. Received Call .............................................................. 30 3.5.3. Dialed Call ................................................................... 31 3.5.4. Erasing Call ....................................................................... 32

3.6. Settings................................................................................... 33 3.6.1. Setting the Ring Melody.............................................. 33 3.6.2. Setting the Vibration Mode......................................... 34 3.6.3. Adjusting the Ring Volume ......................................... 34 3.6.4. Setting the Time ......................................................... 35 3.6.5. Setting the Date.......................................................... 35 3.6.6. Setting the Banner...................................................... 36 3.6.7. Setting the Key Lock .................................................. 36 3.6.8. Don’t Disturb ............................................................... 37

4. Web Configuration ...........................................................38 4.1. Login Password....................................................................... 38

5. Basic Phone Tasks ..........................................................39 5.1. Dialing a Phone Number ......................................................... 39

5.2. Redialing a Phone Number ..................................................... 39

5.3. Answering a Call ..................................................................... 39 6. Display Messages ............................................................40

6.1. Error Messages....................................................................... 40

6.2. Warning Messages.................................................................. 41

5

1. Introduction This is an Administrator’s manual describing the wireless IP phone WLAN600 running in Administrative mode. Before using WLAN600, some setup processes are required to make the phone work properly. You should at least setup the IP address of WLAN600 and router when DHCP is disabled. When DHCP server is available, you can skip the process of setting up the WLAN600 IP address.

Figure 1.1 Network connections for WLAN600

Internet

Proxy ServerProxy Server

AP

ADSL Modem

AP

ADSL Modem

WLAN600 WLAN600

6

2. Getting Started Please check the following before using the WLAN600:

Package contents How to install and remove the battery How to charge the battery How to turn on/off the device

2.1. Package Contents You should find the following contents in your WLAN600 package:

WLAN600 Wireless IP Phone x1 Standard battery x1 Power charger x1 WLAN600 Wireless IP Phone User’s Guide x1 Power Supply (AC adapter) x1 Phone belt clip x1

If any of these items are missing or damaged, please contact your distributor or sales representative immediately.

2.2. Installing and Removing the Battery Step 1. With the phone display face down, push down on the grooves and slide the battery

cover off the telephone.

Figure 2.2-1 Removing the Back Panel

Step 2. With the battery label facing towards you; align the three metal contacts on the battery with the three corresponding contacts on the telephone and press the battery down into its place.

7

DO NOT remove the plastic tab.

Figure 2.2-2 Inserting the battery

Remember to switch the power off before removing the battery.

Step 1. With the the phone face down, slide the battery cover off of the phone. Step 2. Pull the plastic tab on the battery base to easily remove the battery.

Figure 2.2-3 Removing the battery

2.3. Charging the WLAN600

Step 1. Connect the AC adaptor included in the package (use only this adaptor) to the charger. Plug the lead from the adaptor into the circular jack on the bottom of the power charger.

Figure 2.3-1 Connecting the power cord

Step 2. Plug the AC adapter into a standard wall outlet.

Plastic Tab

8

Figure 2.3-2 Plugging-in the charger

Step 3. Place the phone on the charger. WLAN600 automatically turns on. Step 4. The battery-strength indicator on the right side of the display will scroll.

12:00 WLAN600

Not Registered Menu Names

Figure 2.3-3 Battery-strength Indicator

Charge the battery for five hours before using your WLAN600.

Figure 2.3-4 Charging the battery

Step 1. The battery-strength indicator stops scrolling when when the battery is fully charged.

Step 2. Remove the phone from the charger.

9

2.4. Keypad

Figure 2.4-1 WLAN600 Wireless IP Phone

KEY DESCRIPTION

Soft key 1 This key is used for making selections on the bottom left side of the phone LCD, such as: Menu, Select, OK... Its current function is indicated by the word appearing above the key.

Soft key 2 This key is used for making selections on the bottom right side of the phone LCD, such as: Names, Back, Clear... Its current function is indicated by the word appearing above the key.

Arrow keys Use the arrow keys to navigate through your phone’s menus and submenus, as well as your Phonebook. The up / down arrow keys are also used for selecting the character mode: A, a, 1, @.

Talk Key Use this key to answer a call or make a call.

End Key / Power Key Use this key to end a call, reject a call or return to Standby mode. Press and hold this key for two seconds to switch off / switch on the phone.

Numerical / special keys Use to enter numbers, characters or special characters.

● End key

● Power key

Soft Key 1

Arrow Keys

Talk key

Load Default IP (192.168.0.6)

Soft Key 2

Mono Graphic LCD

Numerical keys &

special keys: @, *, #, etc.

10

2.5. Turn On/Off the Power To turn on/off the power, press and hold the key for approximately 2 seconds. The phone enters the “standby” mode; Main Screen is displayed as shown in Figure 2.5-1

Figure 2.5-1 Standby Mode

2.6. Load Default IP Address 1. Turn of the power.

2. Press and hold the “ ” + “ ” keys for about 2 seconds to load the

default IP address. WLAN600 will reset to the default IP address (192.168.0.6).

Figure 2.6-1 Load default IP

2.7. Enter Administrative Mode 1. Turn of the power.

2. Press the “ ” + “ ” + ” ” keys and hold till the

is shown on the LCD screen. Then release the keys.

3. In approximately 10 seconds, you will enter the main screen of the administrative mode.

Figure 2.7-1 Administrative Mode

12:00 WLAN600-user Not Registered

Menu Names

Initializing...

>>Please Wait!

11

2.8. Locking & Unlocking the Keypad Follow these steps to lock & unlock the keypad:

1. In idle state, hold the key over 2 seconds or wait over 1 minute. The keypad will be locked, as shown in Figure 2.8-1.

Figure 2.8-1 Keypad Locked

2. To release, press and hold the key for approximately 2 seconds and the message will appear prompting you to confirm, the procedure like Figure 2.8-2.

Figure 2.8-2 Keypad Unlocked

3. When locking, press any key would show, Figure 2.8-3.

Figure 2.8-3 Keypad Locked

10/20

12:00

X


Menu Names

10/20

12:00

X

10/20

12:00

X

10/20

12:00

X

10/20

12:00

X

10/20

12:00

X

10/20 WLAN600-user Not Registered

Menu Names

10/20

12:00

12

2.9. Adjusting the Speaker Volume During conversation, press the ► key to increase the volume. To decrease the volume, during conversation, press the ◄ key. See Figure 2.9-1.

Figure 2.9-1 Adjusting the Speaker Volume

2.10. Selecting the Character Mode Use the up / down arrow keys (▲ /▼) to select the character mode: capital or lowercase characters, numbers or special characters (A, a, 1, @).

Character Mode Figure 2.10-1 Selecting the

12:00 12 ) ) ) ) ) ) ) ) ) ) 123456

Phone Number 100| Ok Aa1@ Back

13

3. Configuring Network Environment This chapter explains how to modify the network environment.

3.1. Network Configuration This section introduces modifications to the network information.

3.1.1. Fixed IP This section introduces how to select Fixed IP.


Menu Names

Menu

Select Select

Back

IP Address 192.168.0.6| Ok Aa1@ Back

Subnet Mask 255.255.0.0|

Ok Aa1@ Back

Select

Gateway 172.16.0.1| Ok Aa1@ Back

Select Back

Back

Back

4. Net Setting 5. SIP Setting 6. Settings Select Back Back

[1]Fixed IP [2]DHCP [3]PPPoE Select Back

2. IP Address 3. Subnet Mask 4. Gateway Select Back

Select

3. Subnet Mask 4. Gateway 1. Network Mode Select Back

4. Gateway 1. Network Mode 2. IP Address Select Back

[1]Fixed IP [2]DHCP [3]PPPoE Select Back

OK Select

1. Network Mode 2. IP Address 3. Subnet Mask Select Back

Back

Back

Back

Ok

IP Address 192.168.0.6| Ok Aa1@ Back

OK

Ok

Subnet Mask 255.255.0.0|6| Ok Aa1@ Back

OK

Ok

Gateway 172.16.0.1| Ok Aa1@ Back

OK

14

3.1.2. DHCP This section provides instructions for performing the DHCP settings. The Dynamic Host Configuration Protocol (DHCP) client provides a mechanism for allocating IP address dynamically so that addresses can be reused when hosts no longer need them.


Menu Names

Menu

Select Select

Back

4. Net Setting 5. SIP Setting 6. Settings Select Back Back

[2]DHCP [3]PPPoE [1]Fixed IP Select Back

[2]DHCP [3]PPPoE [1]Fixed IP Select Back

OK Select


15

3.1.3. PPPoE The Point-to-Point Protocol over Ethernet (PPPoE) provides more than just IP address assignment, which is the primary purpose of DHCP (assigning a unique and available IP address based upon a unique network adapter address). PPPoE also allows for the movement of TCP/IP traffic between two known points. It requires a username and password to log on.

PPPoE Name pppoe_username| Ok Aa1@ Back

Select Ok

PPPoE Pwd ************| Ok Aa1@ Back

Select Ok Back

Back


Menu Names

Menu

Select Select Select

Back Back

4. Net Setting 5. SIP Setting 6. Settings Select Back


[3]PPPoE [1]Fixed IP [2]DHCP Select Back

3. PPPoE Pwd 1. Network Mode 2. PPPoE Name Select Back

2. PPPoE Name 3. PPPoE Pwd 1. Network Mode Select Back

Input the name

Input the password

Back

Back

[3]PPPoE [1]Fix IP [2]DHCP Select Back

OK

PPPoE Name pppoe_username Ok Aa1@ Back

OK

PPPoE Pwd ************| Ok Aa1@ Back

OK

16

3.2. Wireless Configuration This section provides instructions for configuring the wireless, 802.11b, configuration submenu.

3.2.1. Wireless LAN Settings This section explains the following:

Scanning for the Wireless Service Set Identifier Making wireless settings Setting up WEP Keys (Wireless Equivalent Privacy Keys)

3.2.1.1. Wireless LAN

Ok

2. SSID 3. Network Mode 4. Channel Select Back

Input the SSID


Menu Names

Menu

Select Select

Select

Back Back

7. Wireless 8. Restart 1. Information Select Back

1. Site Survey 2. SSID 3. Network Mode Select Back

AP1 AP2 AP3 Select Back

Back Select

Select

Select

Back

Select Back

Back

[1]Ad Hoc [2]Infra. Select Back

3. Network Mode 4. Channel 5. Rate Select Back

4. Channel 5. Rate 6. WEP Select Select Back

Channel 1 Channel 2 Channel 3 Select Back

Select

Select

Back

Back

5. Rate 6. WEP Select 7. Profile Select Back

[1]Auto [2]1M [3]2M Select Back

Select

Back

SSID bcm-test| Ok Aa1@ Back

AP1 AP2 AP3 Select Back

OK

Back

SSID bcm-test| Ok Aa1@ Back

OK

[1]Ad Hoc [2]Infra. Select Back

OK

Channel 1 Channel 2 Channel 3 Select Back

OK

[1]Auto [2]1M [3]2M Select Back

OK

17

Back

6. WEP Select 7. Profile 8. Auth Type Select Back


Menu Names

Select

Menu

Select Ok

Select

Ok

Ok Back

Back

7. Wep Key 1 8. Wep Key 2 9. Wep Key 3 Select Back

8. Wep Key 2 9. Wep Key 3

10. Wep Key 4 Select Back

9. Wep Key 3 10. Wep Key 4 11. Key Select Select Back

Select

Ok

10. Wep Key 4 11. Key Select 12. Profile Select Back

Input the wep key 1

Wep Key 1 ******* Ok Aa1@ Back

Select




Input the wep key 3

Input the wep key 4

Select Select

Select

Back Back

[1]None [2]64bit [3]128bit Select Back

Select Select

Select

Back

[2]64bit [3]128bit [1]None Select Back


Input the wep key 2

[1]None [2]64bit [3]128bit Select Back

OK

[2]64bit [3]128bit [1]None Select Back

OK

Back


OK


OK


OK

Back

Back

Back


OK

6. WEP Select 7. Profile 8. Auth Type Select Back

Select

Back

11. Key Select 12. Profile 13. Auth type Select Back

Key 1 Key 2 Key 3 Select Back

Key 1 Key 2 Key 3 Select Back

OK SelectBack

18

Select Back

Select

[1]Open System [2]Shared Key Select Back

OK


Select


Menu Names

Menu

1: (AP) Bcm 2: 3: Select Back

Select

Back

1. Create 2. Activate 3. Remove Select Back

12. Profile 13. Auth type

1. Site Survey Select Back

Select

Back


OK

2. Activate 3. Remove 1. Create Select Back

3. Remove 1. Create 2. Activate Select Back

Select

Back

[1]Open System [2]Shared Key Select Back

13. Auth type 1.Site Survey 2.SSID

Select Back

Select


OK


Select

Back


Select

Back

Are you sure?

Ok Back

Ok

Select Back

19

3.3. SIP Configuration This section provides information on the Session Initiation Protocol (SIP) settings. Please note that you have to configure both, Registrar Server , SIP Proxy Server and Outbound Proxy.

3.3.1. Registrar IP Settings

12:00 WLAN600-userNot Registered

Menu Names

Menu

Select Back

Registrar IP 192.168.0.3| Ok Aa1@ Back

Select Ok

Select

Back

Port 5060| Ok Aa1@ Back

Select Ok Back

2. Port 3. Expiry Time 1. Registrar IP Select Back

Input the Registrar IP 1. Registrar IP 2. Port 3. Expiry Time Select Back

Input the Port

Expiry Time 3600| Ok Aa1@ Back

Select Ok Back

3. Expiry Time 1. Registrar IP 2. Port Select Back

Input the Expiry Time

5. SIP Setting 6. Settings 7. Wireless Select Back

Registrar IP 192.168.0.3| Ok Aa1@ Back

OK Back

Back

Back


OK

Expiry Time 3600| Ok Aa1@ Back

OK

1. Registrar 2. Outbound Proxy 3. Proxy Server Select Back

20

3.3.2. Outbound Proxy Settings

Back

Select


Menu Names

Menu


Proxy IP 192.168.0.191| Ok Aa1@ Back

Select

Ok

Select


Select

Ok Back

2. Outbound Proxy 3. Proxy Server 4. User Account Select Back

1. Proxy IP 2. Port Select Back

2. Port 1. Proxy IP Select Back

Input the Proxy IP

Input the Port Port 5060| Ok Aa1@ Back

OK


OK Back

Back

Back

21

3.3.3. SIP Proxy Server Settings

Back

Select


Menu Names

Menu



Select

Ok

Select


Select

Ok Back

3. Proxy Server 4. User Account 1. Registrar Select Back

1. Proxy IP 2. Port Select Back

2. Port 1. Proxy IP Select Back

Input the Proxy IP

Input the Port Port 5060| Ok Aa1@ Back

OK


OK Back

Back

Back

22

3.3.4. Setting up the User Account This section explains how to set up your phone number, username and password you will be using to connect to the SIP server.

Select Back


Menu Names

Menu


Input the number

Input the name

Input the password


Select

Ok

Select

Back

Username David| Ok Aa1@ Back

Select

Ok Back

Back

4. User Account 1. Registrar 2. Outbound Proxy Select Back

1. Phone Number 2. Username 3. User Pwd Select Back

2. Username 3. User Pwd 1. Phone Number Select Back

User Pwd ******| Ok Aa1@ Back

Select

Ok

3. User Pwd 1. Phone Number 2. Username Select Back

Back


OK

Username David| Ok Aa1@ Back

OK Back

Back

User Pwd ******| Ok Aa1@ Back

OK

23

3.4. Using the Phonebook This section provides information about accessing the phonebook and using its features.

3.4.1. Searching Phonebook Entries - Edit Entry

Back

Select

P2P Proxy Select Back

Port: 5060 Ok Aa1@ Back

User Info: 123456| Ok Aa1@ Back


Menu Names

Menu

Select Back

Display Name: David| Ok Aa1@ Back

3. Phonebook 4. Net Setting 5. SIP Setting Select Back

1. Search 2. Add Entry 3. Erase Select Back

Select

Back

David Mark Ken Select Back

1. Edit 2. Erase 3. Speed dial Select Back

Host IP: 172.16.156.123| Ok Aa1@ Back

Edit the number

Edit the IP

SelectP2P Proxy Select Back

OK

SelecOk

Ok

Ok

Ok

Select Edit the name


Press key , go back menu Back


24

3.4.2. Searching Phonebook Entries - Erase Entry



Back


Menu Names

Menu

Select

Back

Are you sure?

Ok Back

Select

3. Phone book 4. Net Setting 5. SIP Setting Select Back

Select

David Mark Ken Select Back

2. Erase 3. Speed dial 1. Edit Select Back

Select

Ok Select

Are you sure?

Ok Back

OK

Back


25

3.4.3. Searching Phonebook Entries – Speed dial Entry

Back

Select



Menu Names

Menu

Select Back

Select



Select

David Select Back

3. Speed dial 1. Edit 2. Erase Select Back

Select

Key 1 David Key 2 Key 3 Select Back

Select

Key 1 David Key 2 Key 3 Select Back

OK Back


26

3.4.4. Adding a Phonebook Entry This section provides information on adding a new entry in your Phonebook.


OK


Menu Names

Display Name: David| Ok Aa1@ Back

User Info: 123456| Ok Aa1@ Back


2. Add Entry 3. Erase 1. Search Select Back

Host IP: 123.123.123.123| Ok Aa1@ Back

Input the name Input the number Input the IP


Port: 5060 Ok Aa1@ Back

Select

Ok Ok

Select

Select Back

Menu

Back

Ok

Ok




27

3.4.5. Erasing Phonebook Entries - One By One This section explains how to erase an existing entry from your Phonebook.

1. One By One 2. Erase All Select Back

Are you sure?

Ok Back

Select

1. One By One 2. Erase All Select Back

Ok

3. Erase 1. Search 2. Add Entry Select Back

Select


Menu Names

Select Back

Select

Select Back

Back

Menu


David Select Back

Are you sure?

OK Back

OK


28

3.4.6. Erasing Phonebook Entries - All This section explains how to erase all entries from your Phonebook.

Are you sure?

Ok Back

Ok

Are you sure? OK Back

OK

2. Erase All 1. One By One Select Back

2. Erase All 1. One By One Select Back

3. Erase 1. Search 2. Add Entry Select Back

Select


Menu Names

Select Back

Select

Select Back

Back

Menu


29

3.5. Call History Call History is a useful feature for checking missed calls, received calls, and dialed calls.

3.5.1. Missed Call This option allows you to check for missed calls, then edit, save and dial the selected phone number.

Select

Are you sure?

Ok Back

Back


Menu Names

Menu

Select Back

Select

Select

2. Call History 3. Phonebook 4. Net Setting Select Back

1. Missed Call 2. Received Call 3. Dialed Call Select Back

Select Back

David Select Back

Select Back

Select

Back

2. Edit Missed 3. Erase Miss 1. Time of Call Select Back

Time of Call 20:03 10/20

Ok Back

User Info: 808 Ok Aa1@ Back

Ok

1. Time of Call 2. Edit Missed 3. Erase Miss Select Back Back

Display Name: David Ok Aa1@ Back


OK

Ok

Back

3. Erase Miss 1. Time of Call 2. Edit Missed Select Back

Select Back

Back

Select

Ok

Are you sure?

Ok Back

OK

1. Missed Call 2. Received Call 3. Dialed Call Select Back



30

3.5.2. Received Call This option allows you to check for received calls, then edit, save and dial the selected phone number.

Select

Back


Menu Names

Menu

Select Back

Select

Select


2. Received Call 3. Dialed Call 4. Erase Call Select Back

Select Back

David Select Back

Select Back

Select

Back

2. Edit Receive 3. Erase Receive 1. Time of Call Select Back


Ok Back


Ok

1. Time of Call 2. Edit Receive 3. Erase Receive Select Back Back



OK

Ok

Back

3. Erase Receive 1. Time of Call 2. Edit Receive Select Back

Select Back

Back

Are you sure?

Ok Back

Select

Ok

Are you sure?

Ok Back

OK

2. Received Call 3. Dialed Call 4. Erase Call Select Back



31

3.5.3. Dialed Call This option allows you to check for dialed calls, then edit, save and dial the selected phone number.

Select

Display Name: David Ok Aa1@ BackBack


Menu Names

Menu

Select Back

Select

Select


3. Dialed Call 4. Erase Call 1. Missed Call Select Back

Select Back

David Select Back

Select Back

Select

Back

2. Edit Dialed 3. Erase Dial 1. Time of Call Select Back


Ok Back


Ok

1. Time of Call 2. Edit Dialed 3. Erase Dial Select Back Back


OK

Ok

Back

3. Erase Dial 1. Time of Call 2. Edit Dialed Select Back

Select Back

Back

Are you sure?

Ok Back

Select

Ok

Are you sure?

Ok Back

OK

3. Dialed Call 4. Erase Call 1. Missed Call Select Back



32

3.5.4. Erasing Call

Are you sure?

Ok Back

Select

Back

Are you sure?

Ok Back

OK

Select Back

4. Erase Dial 1. Erase All 2. Erase Miss Select Back

Select

Back

Are you sure?

Ok Back

OK

Select

Back

Are you sure?

Ok Back

OK

2. Erase Miss 3. Erase Receive 4. Erase Dial Select Back

3. Erase Receive 4. Erase Dial 1. Erase All Select Back

Select Back

Are you sure?

Ok Back

OK

Are you sure?

Ok Back

OK

Are you sure?

Ok Back

OK

Select

Select

Select

1. Erase All 2. Erase Miss 3. Erase Receive Select Back

Select


Menu Names

Menu

Select Back


Back

Select

Back

Are you sure?

Ok Back

OK

Select Back

4. Erase Call 1. Missed Call 2. Received Call Select Back

Are you sure?

Ok Back

OK

Select

Are you sure?

Ok Back

Are you sure?

Ok Back

Are you sure?

Ok Back

33

3.6. Settings This section describes how to modify melody, ring volume, time, banner, etc.

3.6.1. Setting the Ring Melody


Menu Names

Menu

Select Back

6. Settings 7. Wireless 8. Restart Select Back

1. Melody 2. Vibrator 3. Ring Volume Select Back

Default Melody 1 Melody 2 Select Back

Select

Back

Select

Default Melody 1 Melody 2 Select Back

OK

34

3.6.2. Setting the Vibration Mode

3.6.3. Adjusting the Ring Volume

Use the left / right arrow keys (◄ / ►) to decrease / increase the ring volume.


Menu Names

Menu

Select Back


2. Vibrator 3. Ring Volume 4. Edit Time Select Back

Select

Back

Select Ring Only Vibrate Only Vibrate - Ring Select Back

OK

Ring Only Vibrate Only Vibrate -> Ring Select Back


Menu Names

Menu

Select Back


3. Ring Volume 4. Edit Time 5. Edit Date Select Back

Select

Back

Select

Ring Volume

Select Back

OK Ring Volume

Select Back

35

3.6.4. Setting the Time

3.6.5. Setting the Date


Menu Names

Menu

Select Back


4. Edit Time 5. Edit Date 6. Banner Select Back

Select

Back

Select

Edit Time 12:00| Ok Back

OK Edit Time 12:00| Ok Back


Menu Names

Menu

Select Back


5. Edit Date 6. Banner 7. Key Lock Select Back

Select

Back

Select

Edit Date 2004.08.04| Ok Back

OK Edit Date 2004.08.04| Ok Back

36

3.6.6. Setting the Banner

3.6.7. Setting the Key Lock


Menu Names

Menu

Select Back


7. Key Lock 8. Don’t Disturb 9. Load Default Select Back

Select

Back

Select

off on Select Back

off on Select Back

OK


Menu Names

Menu

Select Back


6. Banner 7. Key Lock 8. Don’t Disturb Select Back

Select

Back

Ok

Banner WLAN600-SIP Ok Aa1@ Back

OK Banner WLAN600-SIP Ok Aa1@ Back

37

3.6.8. Don’t Disturb


Menu Names

Menu

Select Back


8. Don’t Disturb 9. Load Default 1. Melody Select Back

Select

Back

Select

off on Select Back

off on Select Back

OK

38

4. Web Configuration This chapter explains how to use the WLAN600 web interface to configure your wireless IP phone.

4.1. Login Password Use your browser to access the WLAN600 web page – in the Address field, type: http:// , then click the Go button. WLAN600 offers two default accounts: 1. the user’s account,

User Name: user Password: 1111

2. and the administrative account User Name: voipadmin Password: admin

The main web page is divided into several frames, each related to a VoIP module. It includes information, network settings, SIP proxy server settings, registrar server settings, phone book settings, voice codec settings, voice quality settings, system settings, and update settings.

39

5. Basic Phone Tasks

5.1. Dialing a Phone Number 1. In idle state, enter a phone number by using the numerical keys. 2. If you have entered an incorrect number, press the key to delete it. 3. Press the key to connect your call.

5.2. Redialing a Phone Number 1. In idle state, press the key.

The list of placed calls is displayed. 2. Scroll through the list by using the or key.

Press the key to make the call.

5.3. Answering a Call To answer a call, press the key. To reject a call, press the key.

40

6. Display Messages

6.1. Error Messages Error messages are displayed to let you know that an error has occurred. These error messages may prevent you from connecting to the network or from using the phone. You may need to contact the system administrator to resolve the problem.

Error 1: No AP found ( blinking) The ESSID set on the phone does not match any of the Service Set Identifiers (SSIDs) of the AP in the network.

Error 2: Net Fail! (DHCP) The phone failed to obtain the IP address from the DHCP server, or failed to authenticate due to a Wep Key error.

Error 3: Net Fail! (PPPoE) The phone failed to obtain the IP address from your ISP service.

Error 4: Registering to SIP proxy failed The phone failed to register with the SIP Proxy. It could be due to the WEP key or SIP proxy setting error. Please contact your service provider, or check your SIP

Settings.


Menu Names

12:00 WLAN600-user

Net Fail! (DHCP) Menu Names

12:00 WLAN600-user

Net Fail! (PPPoE) Menu Names


Menu Names

41

6.2. Warning Messages Warning messages are displayed when the phone detects a condition that may disrupt your phone service.

Warning 1: No display when the phone is seated in the charger. - Situation 1: The phone is seated in the charger but there is

no LCD display and back light, even if it has been powered on.

- Situation 2: The phone is seated in the charger but there is no LCD display; the back light is on.

Corrective Action:

Place the phone in the charger and turn off the power. Keep the phone in the charger for approximately 30 seconds. Then remove it from the charger briefly, for approximately 2 seconds. Place the phone back in the charger and it will automatically turn on. Warning 2: Battery Low ( blinking) The battery energy level is low. Corrective Action: Recharge the battery.

Warning 3: Weak signal detected ( blinking) The signal quality is low. Corrective Action:

Connect to another AP. Move your phone closer to the AP. There may be too much radio interference (for example a microwave or another AP using the same channel) around your wireless network. Relocate or reduce the radio interference.

12:00 WLAN600-user

Net Fail! (DHCP) Menu Names


Menu Names

Administrator’s Guide Wireless IP Phone...

Documents

Transcript of Administrator’s Guide Wireless IP Phone...