adhesives for orthodontics � en

Adhesivescustom made for the fixed appliance technique

2

ULTRA-MINITRIM®

Bracket-Program:

equilibrium® ti

equilibrium®

3

– The dual cure adhesive Page 4

– The light cure adhesive Page 6

– The light cure lingual retainer adhesive Page 8

– The orthodontic light source Page 10

– The microfine glass ionomer cement Page 12

– The moist cure adhesive Page 14

Orthodontic Bonding System – Mix and No-Mix, the classic adhesives Page 16

Delivery Program:

Set Order No. 163-520-00

Contents:1 piece ConTec Duo adhesive in dual chamber cartridge (5 ml)10 pieces ConTec Duo Tips automix application tubes1 piece ConTec Etch etching gel in syringe (5 ml)

+ 2 curved application tubes1 piece ConTec Prime primer in bottle (5 ml)

50 pieces Brushes1 piece Brush holder2 pieces Mixing pads

Single Packs: Order No.

1 piece ConTec Duo adhesive in dual chamber cartridge (5ml) 163-521-0010 pieces ConTec Duo Tips automix application cartridge163-522-001 piece ConTec Etch etching gel in syringe (5ml) 163-512-00

+ 2 curved application cartridges1 piece ConTec Prime primer in bottle (5ml) 163-513-00

50 pieces Brushes 163-417-005 pieces Brush holders 163-419-002 pieces Mixing pads 163-416-00

4

was developed specifically for bonding applications where ease of useand perfect bonding, even in hard to access areas, is of prime importance. This dual cure twocomponent adhesive system is perfectly suited for bonding metal brackets and buccal tubes.The innovative mix technique with an auto-mix application cartridge guarantees an even mixof the adhesive, thereby, optimizing the material properties.

Dual cureThe combination of chemical and light polymerization is a definite plus for reliability. Even inhard to access areas, or in material restricted areas (metal brackets), the chemical polymeriza-tion guarantees the total cure of the adhesive.

Comfortable working timeDue to the light hardening components of the ConTec Duo adhesive system, the practitionerdetermines the start for the light polymerization.

Easy handling - perfect mixThe special ConTec Duo tip automix application cartridge achieves a quick and even mix ofthe two adhesive components. This assures the optimal bonding potential.

Universal applicationDue to the above mentioned properties, ConTec Duo is applicable for all types of brackets (metal, ceramic, plastic) and buccal tubes.

Easy storageConTec Duo can be stored at room temperature for an extended period of time.

ConTec Duo contains fluoride

5

Delivery Program:

Set Order No. 163-510-00

Contents:3 pieces ConTec LC adhesive in syringes (2ml)10 pieces ConTec LC Tips application tubes

for adhesive syringes1 piece ConTec Etch etching gel in syringe (5 ml)

+ 2 curved application tubes1 piece ConTec Prime primer in bottle (5 ml)

50 pieces Brushes1 piece Brush holder2 pieces Mixing pads

Single Packs: Order No.

1 piece ConTec LC adhesive in syringe (2ml) 163-511-0010 pieces ConTec LC Tips application tubes 163-514-00

for adhesive syringes1 piece ConTec Etch etching gel in syringe (5ml) 163-512-00

+ 2 curved application cartridges1 piece ConTec Prime primer in bottle (5ml) 163-513-00

50 pieces Brushes 163-417-005 pieces Brush holders 163-419-002 pieces Mixing pads 163-416-00

6

is the result of focused research in order to develop an adhesivethat would guarantee a secure bonding between the tooth and the bracket or buccaltube, and to allow for an easy and quick working process.

Comfortable working timeThe light initiated adhesion of ConTec LC facilitates a precise bonding. The practitioner candetermine the start of the fixation.

Optimal consistencyConTec LC has an optimal viscosity that allows for sufficient initial fixing, as well as easy finalpositioning.

Quick loading capacityImmediately after light polymerization of ConTec LC has been completed, the bracket or buccal tube can be ligated.

Universal applicationDue to the above mentioned properties, ConTec LC is applicable for all types of brackets(metal, ceramic, plastic) and buccal tubes.

Easy storageConTec LC can be stored at room temperature for an extended period of time

ConTec LC contains fluoride

7

Delivery Program:

Set Order No. 163-530-00

Contents:10 pieces ConTec LCR caps adhesive (0.25g)1 piece ConTec Etch etching gel in syringe (5 ml)

+ 2 curved application tubes1 piece ConTec Prime primer in bottle (5 ml)

50 pieces Brushes1 piece Brush holder2 pieces Mixing pads

Single Packs: Order No.

25 pieces ConTec LCR caps adhesive (0.25g) 163-531-001 piece ConTec Etch etching gel in syringe (5ml) 163-512-00

+ 2 curved application cartridges1 piece ConTec Prime primer in bottle (5ml) 163-513-00

50 pieces Brushes 163-417-005 pieces Brush holders 163-419-002 pieces Mixing pads 163-416-00

Not included in assortment, available only as individual purchase:1 piece ConTector, applicator for ConTec LCR caps 163-532-00

8

was developed especially for bonding retainers, introducing anadhesive that due to its viscosity guarantees maximum distribution to retainer andtooth, and at the same time enable easy and quick preparation to ensure save bondingproperties.

Comfortable working timeThe light initiated polymerization of ConTec LCR facilitates precise bonding. The practitionercan determine the starting time for fixation.

Optimal consistencyConTec LCR's optimal viscosity has been especially set for bonding retainers. It ensures a suffi-cient initial fixation, as well as even distribution of the adhesive.

Precise application - easy handlingThe ConTector/ConTec LCR flow cap system requires minimal preparation, allowing for easyand quick processing. One ConTec LCR flow cap is sufficient for the treatment of one patient.

Easy storageConTec LCR can be stored at room temperature for an extended period of time.

ConTec LCR contains fluoride

9

Delivery Program:

Light Order No. 073-000-00Contents:1 piece ConTec Light halogen light applicator

with power base, hand piece and accessories

Technical data:

Electrical connection: 230V - 50/60 Hz - changeable to 115V - 50/60HzWeight of hand piece 310 gWeight of power base: 1020 gLight intensity, adjustable: 200 ….. 1000 mW/cm2Light guide: � 11 mm, 60° bent, included with unitLight source: 12V/81W special halogen lamp for maximum output.Cooling: Turbo cooling fan, digitally controlled via thermo sensorsPerformance control: Power base integrated digital output sensorTimer: Adjustable setting from 10 to 90 secondsCuring mode: 2 curing modes - ramp curing and standard

curing. Adjustable on the hand piece.Control lights: LED indicators on hand piece, "on" indicator,

lamp status and curing mode.

Replacement parts and accessories: Order No.Turbo tip light guide, from 13mm to 9mm tapered 073-001-00Standard light guide � 11 mm / 60° bent 073-002-00Eye protection shield 073-003-00Halogen bulb 12V/81W 073-004-00Fuse T1,25A 073-005-00

10

Light is the light source that meets all requirements of a modern poly-merization lamp. Especially with regard to special conditions for applications in ortho-dontics that require high photon emission.

Easy handlingConTec Light is ergonomically shaped to fit the hand. The design enables easy access, even inhard to reach areas.

High safety standardsThe integrated eye protection shield protects against reflections. The thermo sensor regulatedcooling fan is quiet and prevents overheating.

Optimal light emission for orthodontic applications

The ConTec Light offers the maximum reachable light emission that allows for sufficient capacity. Even in difficult working positions, that occur on a daily basis in orthodontics, aquick and complete polymerization can be achieved.

High outputThe halogen bulb in the ConTec Light is the most powerful bulb on the dental market. Thebulb was developed especially for the ConTec Light and is guaranteed for 2 years.

Comfortable handlingThe light emission of the ConTec Light is adjustable. The operation mode (ramp cure, standard cure) is visible on the hand piece. The integrated timer makes it easy to check the time span. The hand piece is equipped with an extra long cable (2 meters) to ensure moveability. Distinct acoustic signals announce the start and ending of the polymerizationprocess.

11

Delivery Program

Order No. 163-540-00

Contents:1 piece GlasTec glass ionomer cement powder in bottle (35g)1 piece Measuring spoon1 piece Water bottle

12

was developed especially for the secure attachment of orthodonticbands. The formula's microfine structure of components guarantees optimal bondingresults.

Easy mixingThe microfine consistency of GlasTec enables quick, easy, as well as material saving mixing.

Excellent processing timeGlasTec's processing time allows sufficient time for a precise application, without undue timepressure.

Good adhesionThe bond between band and tooth has to withstand strong forces, especially in the molarregion. The special formula of GlasTec assures a firm bond and offers the best provisions foran undisturbed treatment process.

Easy storageGlasTec can be stored at room temperature for an extended period of time.

GlasTec contains fluorideFluoride emission over a long period of time.

13

Delivery Program:

Set Order No. 163-505-00Contents: 2 pieces SmartBond® orthodontic adhesive in syringes (3g)

2 pieces SmartBond® etching gel in syringes (6g)50 pieces SmartBond® brushes40 pieces SmartBond® Luer-lock tips1 piece SmartBond® mixing pad

14

was developed especially for orthodontic applications. The special formulaassures a secure bond, even on moist bonding surfaces.

Wet bondingSmartBond® adheres without problems, even on moist bonding surfaces, and hardens securelyunder the influence of moisture. This makes the treatment easier and more pleasant for bothpractitioner and patient.

Easy bondingThere is no need for a primer*, nor for a polymerization lamp to obtain optimal bonding.

Universal applicationSmartBond® is an excellent bonding agent for all types of brackets* and buccal tubes.

* When using plastic brackets, please follow the manufacturer's instructions. Do not use on ceramic brackets with a silane base.

15

Delivery Program:

No-Mix Assortment in Jars Order No. 163-406-00

Contents: 1 piece bracket adhesive (8g), 1 piece activator (10ml),1 piece etching gel (10ml), 50 pieces disposable brushes,2 pieces brush holders, 50 pieces spatulas, 2 pieces mixing pads

No-Mix Assortment in Syringes Order No. 163-407-00

Contents: 3 pieces bracket adhesive in syringes (2.5g), 1 piece activator (10 ml), 2 pieces etching gel in syringes (2.5g), 50 pieces disposable brushes,2 pieces brush holders, 50 spatulas, 6 pieces disposable tubes for etchinggel, 2 pieces mixing pads

No-Mix Assortment in Minitips Order No. 163-407-01

Contents: 5 pieces bracket adhesive in minitips (0.12g), 1 piece activator (10 ml), 1 piece etching gel in syringe (2.5g), 1 piece applicator, 5 pieces disposabletubes for etching gel syringes, 1 piece brush holder, 10 pieces disposablebrushes, 2 pieces mixing pads

Single Packs: Order No.

1 piece No-Mix adhesive in jar (8g) 163-413-00

2 pieces No-Mix adhesive in syringes (2.5g) 163-421-00

5 pieces No-Mix adhesive in minitips (0.12g) 163-425-00

1 piece No-Mix activator (10 ml) 163-414-00

1 piece Etching gel in bottle (10 ml) 163-415-00

2 pieces Etching gel in syringes (2.5g) 163-412-00

10 pieces Disposable tubes for etching gel syringes 163-422-00

50 pieces Brushes 163-417-00

50 pieces Spatulas 163-418-00

5 pieces Brush holders 163-419-00

2 pieces Mixing pads 163-416-00

16

NO-MIX is a paste/liquid adhesive to bond metal, ceramic and plastic brackets, as well asbuccal tubes. This polymerization is initiated by pressing.

Three types of adhesiveThe practitioner can choose the preferred method .The NO-MIX program will be a guide toselect either jar, syringe or minitips.

Comfortable working timeNO-MIX facilitates precise bonding. The practitioner decides the starting time of fixation.Position the bracket on the tooth – press - finished.

Easy debondingAt time of bracket removal, the debonding point is transferred into the adhesive/base area inorder to protect the tooth enamel.

Universal applicationDue to the above mentioned properties and characteristics, NO-MIX is well suited for bondingall types of brackets (metal, ceramic, plastic), and buccal tubes.

17

NO-MIX The classic one-component bracket adhesive

Delivery Program:

Mix Assortment Order No. 163-405-00

Contents: 1 piece paste A in jar (18g), 1 piece paste B in jar (18g)1 piece sealant resin A in bottle (3ml), 1 piece sealant resin Bin bottle (3ml), 1 piece etching gel (10 ml), 2 pieces mixing pads,50 pieces spatulas, 100 pieces application sponges

Single Packs: Order No.

1 piece paste A in jar (18g) 163-408-00

1 piece paste B in jar (18g) 163-409-00

1 piece sealant resin A in bottle (3 ml) 163-410-00

1 piece sealant resin B in bottle (3 ml) 163-411-00

1 piece etching gel in bottle (10 ml) 163-415-00

50 pieces spatulas 163-418-00

100 pieces application sponges 163-420-00

2 pieces mixing pads 163-416-00

18

MIX is a paste/paste adhesive for bonding metal, ceramic and plastic brackets as well asbuccal tubes.

Comfortable working timeMIX facilitates precise bonding.

Optimal adhesionThe adhesive has a very pliable consistency with enough flow and sufficient viscosity to guarantee precise bracket positioning and good adhesion.

Universal applicationThe above mentioned qualities and characteristics make MIX adhesive most suitable for bonding all types of brackets (metal, ceramic, plastic), and buccal tubes.

19

MIX The classic two-component bracket adhesive

Date of information: 07/03

- Subject to changes -

For questions regarding the application of our products, please contact our orthodontics department.

Hot line telephone number: +49 7231/803 550

To place orders: +49 7231/803 210

Information and instructions for Dentaurum bracket adhesives are available on the internet

www.dentaurum.com.

989-

625-

20

Prin

ted

by D

enta

urum

Ger

man

y

07/

03

Turnstraße 31 · 75228 Ispringen · Germany · Telefon +49 72 31 / 803-0 · Fax +49 72 31 / 803-295www.dentaurum.com · E-Mail: info@dentaurum.de