Adhesion Method2

7/24/2019 Adhesion Method2

http://slidepdf.com/reader/full/adhesion-method2 1/18

NSUR2-1 Whispertek™ surface Dual installaton guide

Span™ ideaon system



WHAT YOU’LL NEED

Laser level 3" roller

Two (2) people toinstall the surface.

TABLE OF CONTENTS

Before you begin

Step 1 ̶ Measure and mark

Step 2 ̶

Aligning surface 1

Step 3 ̶ Adhering surface 1

3

4

6

9

Measuring tape

Step 4 ̶ Mounting surface 2 14



WhisperTek

TM

Surface installationhttp://nureva-span.uservoice.com/knowledgebase/articles/603927

70°F 21°C

To avoid cracking, ensure your surfaces have reached

room temperature before removing from the boxes. Allow the

surfaceto rest and flatten before installation.

BEFORE YOU BEGIN



STEP 1

MEASURE AND MARK



Measure and markSet up the laser lever and project a line 1" above the projected image.

Find the overall centerline of the system. Each surface is 124" (314 cm) long and should extend 1" past the projectedimage. Once you have found the centerline, use a straight edge to mark the entire length of the centerline.



STEP 2

ALIGNING SURFACE 1



Peel the adhesive linerCarefully flip one of the surfaces so the adhesive liner is facing up. Fold down a 6-inch widfrom the edge of the surface to where the liner is cut in the center. Fold down a corner of

on the other side of the cut line.



Align surface 1

Do not let the exposed adhesive touch the wall during this step.



STEP 3

ADHERING SURFACE 1



Adhere the top of the surface

Person B presses the exposed adhesive

against the wall ̶ ensuring it is level

with the laser line ̶ then firmly smoothes

the top of the surface against the wall.

Hold the surface in place

Once the surface is aligned, person A holds thesurface firmly against the wall.



Remove the adhesive liner

While person A holds their side of the surface, person B pulls the bottom of the surface away fromthe wall to remove the release liner . Do not bend the surface at a sharp angle as this can causekinking.



Begin adhering the surface to the wall

Starting from the top of the surface and moving downward, person B begins to press the surface against the

wall with overlapping up-and-down strokes to prevent bubbles from forming under the surface.



Adhere the second half of surface 1

Once the first half is adhered, person A pulls the surface away from the wall from the side carefully while avoiding

kinking the surface in the center. Person B goes behind the surface to remove the adhesive liner from the second half of

the surface.

Person A holds the outside edge of the surface while person B smoothes it against the wall using up-and-down stokes.



STEP 4

MOUNTING SURFACE 2



Peel the adhesive liner

Carefully flip the other surface so the adhesive liner is facing up. Fold down a 6-inch wide vethe surface that will touch the system centerline. Fold down the corner of the liner on the o



Align and secure surface 2

Person A and person B hold the surface up to the wall. Person A aligns the inside edge of the surface with thesurface that has already been installed. Once the center edge is completely aligned, person A smoothes downthe exposed adhesive to secure the edge of surface 2 against surface 1.



Person B walks the edge of the surface away from the wall so person A can get behind the surface to remove the linerfrom where it was folded.

While person B holds the outside edge, person A goes back to the front of the surface and smoothes that half of thesurface against the wall starting at the centerline using overlapping up-and-down strokes.

Once person A adheres that side of the surface, person A then goes behind the surface again to remove the second

half of the liner to smooth that side of the surface against the wall.



Roller both surfaces

Apply pressure to both the surfaces using the 3" roller to promote proper adhesion. The surface is now readyfor use.

© 2016 Nureva Inc. All rights reserved. Nureva, Span, WhisperTek and the Span logo are trademarks of Nureva Inc. in the United States, Canada and other countries.

Adhesion Method2

Documents

Transcript of Adhesion Method2