ADDENDUM SUGGESTED- WIRING CONFIGURATION HARNAIS EN T POUR FORD 40-BITS · 2019-11-26 · If the...
Transcript of ADDENDUM SUGGESTED- WIRING CONFIGURATION HARNAIS EN T POUR FORD 40-BITS · 2019-11-26 · If the...
* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN.
CONTACTDE CAPOT
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot est un élément de sécurité essentiel et doit absolument être installé.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
STATUT DE CAPOT : LE CONTACT DE CAPOT, DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT.
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20191125
T-HARNESS FORD 40-BITSHARNAIS EN T POUR FORD 40-BITS
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
Guide # 32161
HARDWARE VERSIONVERSION MATÉRIELLE
FIRMWARE VERSIONVERSION LOGICIELLE
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.Pour ajouter la version logicielle et les options,
utilisez l’outil FLASH LINK UPDATER ou FLASH LINK MOBILE, vendu séparément.
MINIMUM 6 71.[47]FORD MINIMUM
Program bypass option(If this option is not OFF
the Ignition will turn On when the door are unlock):
Programmez l’option du contournement(si cette option n’est pas à NON l’ignition
s’allumera lorsque le véhicule est déverrouillé):
UNIT OPTIONOPTION UNITE DESCRIPTION
A5 OFFNON
AUX.1
AUX.1
“Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)”
VEHICLEVEHI-CULES
YEARS ANNÉES Im
mob
ilize
r byp
ass
Con
tour
nem
ent d
’imm
obili
sate
ur
T-ha
rnes
s av
aila
ble
(Sol
d se
para
tely
)
Lock
Unl
ock
Arm
Dis
arm
RA
P D
isab
le
Hor
n
Tach
omet
er
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s*
Han
d-B
rake
Sta
tus
Foot
-Bra
ke S
tatu
s
OEM
Rem
ote
mon
itorin
g
FORDEdge 40-bits 2007-2010 • • • • • • • • • • • • • •Escape 40-bits 2008-2012 • • • • • • • • • • • • • •
Hybrid 40-bits 2008-2012 • • • • • • • • • • • • • •Flex 40-bits 2011-2012 • • • • • • • • • • • • • • •Fusion 40-bits 2010-2012 • • • • • • • • • • • • • • •Taurus 40-bits 2008-2012 • • • • • • • • • • • • • • •MAZDATribute 40-bits 2008-2011 • • • • • • • • • • • • • •
Page 1 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
Ignition barrelBarillet d'ignition OBD-II connector
Connecteur OBD-II
(~) CAN LOW Pin 11
(~) CAN HIGH Pin3
3
11
RX and TX of the module RX et TX du module
BCM Driver side dash boardBCM Tableau de bord côté chauffeur
Driver door pin
F-150, F-250, F-350, F450:BCM Passenger side dash board Black connector (26-pins) Back view or Driver kick panel Running board harness
BCM Tableau de bord côté passagerConnecteur Noir (26-pins) Vue de dos ou Harnais Coté Conducteur Panneau Latéral Conducteur
(+)Parking Lights Location
Edge Purple/WhiteMauve/Blanc
Harnais in driver kick panel.Harnais dans le panneau latéral côté conducteur.
Escape Purple/WhiteMauve/Blanc
Driver running board. Marche pied côté conducteur.
F-150 Purple/WhiteMauve/Blanc
Passenger kick panel.Harnais dans le panneau latéral côté conducteur.
Flex Purple/WhiteMauve/Blanc
At Smart Junction Box, Connector DÀ la boîte de Junction Intelligente, connecteur D.
Fusion Purple/WhiteMauve/Blanc
Harnais in driver kick panel.Harnais dans le panneau latéral côté conducteur.
Mustang Purple/WhiteMauve/Blanc
Driver Running board harness.Harnais dans panneau latéral côté conducteur.
Taurus Purple/WhiteMauve/Blanc
At Smart Junction Box, Connector E, in driver kick panel. À la boîte de Junction Intelligente, connecteur E, dans le panneau latéral côté conducteur.
Tribute Purple/WhiteMauve/Blanc
Driver running board. Marche pied côté conducteur.
(+) Accessory (+) Start
(~) RX (~) TX
(+) Ignition (+)12V
Page 2 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
Ignition barrelBarillet d'ignition
ImmobilizerImmobilisateur
SEE NEXTPAGE
VOIR PAGE SUIVANTE
12V BATTERY 12V BATTERIE
ATTENTION LE COURANT DU 12V PROVENANT DU HARNAIS-EN-T EST LIMITÉ À 10 AMPÈRES MAXIMUM.
Si les lumières de stationnement (+) requièrent plus de 10 Ampères, branchez le 12V du démarreur à distance directement à la batterie du véhicule avec le fusible approprié.
Certains démarreurs à distance NE peuvent PAS être allimentés par le Data-Link. Dans ce cas, branchez le 12V (avec fusible) du démarreur à distance directement au harnais-en-T.
ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.
If the parking lights (+) require more than 10Amp. connect the remote-starter's power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link. In these cases connect the remote starter's fused 12V power wire directly to the T-Harness.
Make the connection between the UNIT and the T-HARNESSEffectuez les branchements entre le MODULE et le HARNAIS EN T.
T-HARNESS INSTALLATION | INSTALLATION DU T-HARNAIS
Page 3 / 9
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
C3 C4
20 PIN CONN.Use the connector supplied with the unit.Utilisez le connecteur fourni avec le module.
DNOT CONNECTED | NE PAS BRANCHER
C
5 PIN CONN.Use the connector supplied with the unit.Utilisez le connecteur fourni avec le module.
2625
2423
2221
2019
1817
1615
14
1312
1110
98
76
54
32
1
12
34
56
712
1110
98
1316
1514
2625
2423
2221
2019
1817 26
2728
2930
31
109
87
54
32
16
(+)Parking Light CAN LOWCAN HIGH Driver Door Pin
26252423222120191817161514
131211107543211
9 10
2 3 4 5 7 8
11 12 13 14 15 16
6
11
3 686 9
CUT
BCM Driver side dash boardBlack connector (26-pins) Back view
BCM Tableau de bord côté chauffeurConnecteur Noir (26-pins) Vue de dos
OBD-II connector Front viewConnecteur OBD-II Vue de face
Yellow/Black
YellowLt. Blue/Black
Lt. BlueA10
A20
SEE PREVIOUS PAGE
VOIR PAGE PRÉCÉDENTE
A18
A17
B
A
MAKE THE CONNECTIONS I FAIRE LES BRANCHEMENTS
Green/VioletVert/Mauve
Violet/Orange
Violet/Orange
Gray/Orange
Gris/Orange
Purple/WhiteMauve/Blanc
Connection required to arm the factory alarm when the doors are locked and RAP Control. Branchement requis pour armer l'alarme d'origine lorsque les portes sont verrouillées et pour le contrôle du RAP.
HOOD (-) IN RS10A15
LOCKUNLOCKDOOR
FOOT BRAKETACHOMETERHAND BRAKE
(-)
(-)(-)(-)
(+)(+/-)(-) IN RS11
IN RS12 IN RS13
IN RS16OUT RS17OUT RS18
OUT RS14
A14A12A11
A4A3A2
A8
ALWAYS REQUIREDTOUJOURS REQUIS
NOT REQUIRED WITH DATALINKNON REQUIS EN DATA-LINK
START
IGNITION2
PARKING LIGHTACCESSORY
12V BATTERYGround | Masse
RS8 OUT
RS6 OUTRS5 OUTRS4 OUT
RS2 IN(-)(+)
(+)
(+)
(+)IGNITION1 MAINRS7 OUT (+)
PARKING LIGHTRS3 OUT (-)
RS1
REMOTESTARTER
DÉMARREURÀ DISTANCE
WITH | AVEC DATA-LINK:Direct connectionBranchement directe
(+)
Cut | Coupez RedBlack
BlueWhite
B4B3B2B1
Cut | Coupez
BlackRed 12V BATTERY
GroundB4B3
SEE | VOIR NOTE PREVIEWS PAGE
PAGE PRÉCÉDENTE
RS4
WITH DATA-LINK:AVEC DATA-LINK:
WITH D2D:AVEC D2D:
OROU
WITHOUT DATA-LINK:SANS DATA-LINK:
GROUND OUT WHILE RUNNING
NOT CONNECTED | NE PAS BRANCHER
A1/RS7
(+) Ignition Yellow In A1(-) Lock Purple In A2
(-) Unlock Purple/White In A3(-) Door/Trunk Status Green Out A4
White Out A5Orange In A6
Orange/Black In A7(-) Ground While Running Dk.Blue In A8
(+)Start Red/Blue In A9Lt.Blue/Black A10
(+) Foot Brake Black Out A11(-/+) Tachometer Pink Out A12
Yellow/Black In A13(-) Hand Brake Brown/White Out A14(-) Hood Brake Pink/Black Out A15
Purple/Yellow A16Green/White A17
Green/Red A18White/Black A19
Lt.Blue A20
C5 BrownC4 Gray/Black CAN LOWC3 Gray CAN HIGHC2 Orange/BrownC1 Orange/Green
D6 White/RedD5 White/BlueD4 White/GreenD3 Yellow/RedD2 Yellow/BlueD1 Yellow/Green
WIRING CONNECTION | SCHÉMA DE BRANCHEMENT
See page 2.
Voir la page 2.
THAR-FOR1
Page 4 / 9
LO
CK
ACC ON
PUSH
STA
RT
IGN
TURNON/RUN
Wait 3 seconds.
LO
CK
ACC ON
STA
RT
IGNON
WAIT3 SEC.
Attendre 3 secondes.
LO
CK
ACC ON
PUSH
STA
RT
OFFTURNOFF
LO
CK
ACC ON
STA
RT
PUSHPUSH
REMOVEKEY
5
KEY#1CLÉ#1
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION
KEY#2CLÉ#2
KEY#1CLÉ#1
2 KEY REQUIRED2 CLÉS REQUISES
Choose between : Choisir entre:
KEY#1CLÉ#1
KEY#2CLÉ#2
KEY#1CLÉ#1
2 key programming.Programmation avec 2 clés.
DCRYPTOR and 1 key programming.Programmation avec DCRYPTOR et 1 clé.
RELEASE
Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.
Insert the required remaining connectors.
CETTE PROGRAMMATION EST POUR LES FORD 40BITS
1
2
3
ONREDROUGE
Insérez les connecteurs requis restants.
Relâchez le bouton de programmation quand la DEL est ROUGE.
Si le DEL n'est pas ROUGE solide débranchez le connecteur 4 pins (Data-Link) et allez à l'étape 1.
ALLE O ALL
Press and hold the programming button:Connect the 4-PIN Data-link harness (Black connector).
� The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Appuyez et maintenir enfoncé le bouton de programmation: Branchez le harnais Data-Link à 4-Broches (connecteur Noir)
� Les DELs Bleue, Rouge, Jaune et Bleue & Rouge s'allumeront alternativement.
Tournez la première clé fonctionelle à Ignition.
Turn the first functional key to the Ignition ON/RUN position.
Turn the key to the OFF position.
Remove the first key.
Tournez la clé à la position Arrêt (OFF).
Retirez la clé du contact.
x1HOLD
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
4
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 1/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 1/2
PAGE 7
Page 5 / 9
8
Press and release theprogramming button.
The vehicle ignition turnON.
Pesez et relâchezle bouton deprogrammation.
L'ignition du véhicules'allume.
Ignition ON
The RED LED will flashrapidly 10x times.
The BLUE LED will flashrapidly.
Key bypass programmed.
CAN-Bus programmed.
La DEL ROUGE clignotera10x fois rapidement.
La DEL BLEU clignoterarapidement:
Contournement de cléprogrammé.
Réseau CAN programmé.
6
7
5 sec. max
CAUTION The following step mustbe completed within 5 seconds.Otherwise disconnect all connectorsand go back to step 1.
ATTENTION5 secondes.
débranchez allez
les prochaines étapes doivent êtrecomplétées en moins deSi non, tous les connecteurs età l'étape 1.
x1PRESS
Wait 3 seconds. Attendre 3 secondes.
The module is nowprogrammed.
Le module estprogrammé.
Use the remote of the remotestarter or security system to testall of the supported features toensure proper programming.
Testez toutes les fonctionssupportées sur le véhicule avec latélécommande du démarreur àdistance ou du système de sécurité.
The vehicle ignition willturn OFF.
L'ignition du véhicules'éteins.
Ignition OFF
If the LED is solid REDdisconnect the 4 Pinconnector (Data-Link) and goback to step 1.
Si le DEL est ROUGE solidedébranchez le connecteur 4pins (Data-Link) et allez àl'étape 1.
FLASH 10XIGNITION ON
FLASH 10X
FLASH
LOCK
ACC ON
PUSH
START
IGN
KEY#2CLÉ#2
LOCK
ACC ON
START
IGNON.
TURNON/RUN WAIT
3 SEC
LOCK
ACC ON
PUSH
START
OFF
LOCK
ACC ON
START
PUSHPUSH
FTURNOF
REMOVEKEY
Tournez la deuxièmeclé fonctionelle à Ignition.
Turn the second functionalkey to the Ignition ON/RUNposition.
Turn
Remove
the key to the OFFposition.
the second key.
Tournez
Retirez
la clé à laposition Arrêt (OFF)
la deuxième clédu barillet d'alimentation.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/2Page 6 / 9
Parts required (not included) Pièces requises (non incluses)
1x ,
1x software1x Microsoft Windows Computer with Internet connection
FLASH LINK UPDATER FLASH LINK
2MANAGER
1x ,
1x Programme 1x Ordinateur Microsoft Windows avec connection Internet
FLASH LINK UPDATER FLASH LINK
2MANAGER
4
Press and release the programming button once (1x).
Appuyez et relâchez 1 fois le bouton de programmation.
� The RED LED will flash once. � La DEL ROUGE clignote 1 fois.
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
RELEASE
Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.
Insert the required remaining connectors.
1
2
3
ONREDROUGE
Insérez les connecteurs requis restants.
Relâchez le bouton de programmation quand la DEL est ROUGE.
Si le DEL n'est pas ROUGE solide débranchez le connecteur 4 pins (Data-Link) et allez à l'étape 1.
x1PRESS
OFF
ON
PRESS X1
OFF
ON
ON
5
�
�
The YELLOW LED will turn on.
The RED LED will turn OFF.
�
� La
La DEL JAUNE s'allume.
DEL ROUGE s'éteint.
LO
CK
ACC ON
PUSH
STA
RT
IGNON
IGN
6
LO
CK
ACC ON
PUSH
STA
RT
OFF
OFFIGN
IGNITION OFF IGNITION ON
OFFON
ON
IGNITION ON IGNITION OFF
ON OFF
ON
�
�
The YELLOW LED will turn OFF.
The RED LED will turn on.
� La
�
DEL JAUNE s'éteint.
La DEL ROUGE s'allume.
Press and hold the programming button:Connect the 4-PIN Data-link harness (Black connector).
� The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Appuyez et maintenir enfoncé le bouton de programmation: Branchez le harnais Data-Link à 4-Broches (connecteur Noir)
� Les DELs Bleue, Rouge, Jaune et Bleue & Rouge s'allumeront alternativement.
Tournez la clé à Ignition.Turn the key to the Ignition ON/RUN position.
Turn the key to the OFF position.
Tournez la clé à la position Arrêt (OFF).
x1HOLD
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTOR
Parts required (not included) Pièces requises (non incluses)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER 1x FLASH LINK MOBILE1x FLASH LINK MOBILE APP
SOFTWARE | PROGRAMME Smartphone Android or iOS with Internet connection (Internet provider charges may apply)Téléphone Intelligent Android ou iOS avec connection Internet (des frais du fournisseur Internet peuvent s’appliquer)
OROU
Microsoft Windows Computer with Internet connectionOrdinateur Microsoft Windows avec connection Internet1x 1x
Page 7 / 9
LOCK
ACC ON
PUSH
START
IGN
TURNON/RUN
LOCK
ACC ON
PUSH
START
OFFF
TURNOF
8
7
The RED and YELLOW LEDswill alternate.
La DEL ROUGE et JAUNEalternent.
The YELLOW LED will turnon and off.
The RED LED will turn OFF.
La
La DEL JAUNE s'allume ets’éteint.
DEL ROUGE s'éteint.
WAIT, the BLUE LED to flashrapidly.
ATTENDRE que la DELBLEUE clignote rapidement.
Tournez la clé à Ignition.Turn the key to theIgnition ON/RUN position.
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
IGNITION OFF
ONON
FLASH RAPIDLY
OFF
IGNITION OFF IGNITION ON
OFFONON
FLASH
LOCK
ACC ON
PUSH
START
IGN
TURNON/RUN
LOCK
ACC ON
PUSH
START
OFFF
TURNOF
8
7
The RED and YELLOW LEDswill alternate.
La DEL ROUGE et JAUNEalternent.
The YELLOW LED will turnon and off.
The RED LED will turn OFF.
La
La DEL JAUNE s'allume ets’éteint.
DEL ROUGE s'éteint.
WAIT, the BLUE LED to flashrapidly.
ATTENDRE que la DELBLEUE clignote rapidement.
Tournez la clé à Ignition.Turn the key to theIgnition ON/RUN position.
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
IGNITION OFF
ONON
FLASH RAPIDLY
OFF
IGNITION OFF IGNITION ON
OFFONON
FLASH
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/2
EVO-ALL
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite le connecteur Data-Link (4-pins).
*Pièces requises (non incluses)
Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILEto visit the DCryptor menu.
Utilisez l'outil: FLASH LINK UPDATER ou FLASH LINK MOBILEpour visitez le menu DCryptor.
*Parts required (not included)
FLASH LINK UPDATER*
FLASH LINK MOBILE*
FLASH LINK MANAGER*SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection*
Ordinateur Microsoft Windows avec connection Internet*
VEHICLE'S OBDII CONNECTOR
CONNECTEUR OBDII DU VÉHICULE
OROU
Smartphone* (Internet provider chargesmay apply)Téléphone Intelligent* (des frais du fournisseurInternet peuvent s’appliquer)
AFTER DCRYPTOR PROGRAMMING COMPLETEDGo back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION DCRYPTOR COMPLETÉE : retournez au véhicule etrebranchez le connecteur 4-pins (Data-Link) et après, tous les connecteurs du EVO-ALL.
EVO-ALL
9
10
11
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
Page 8 / 9
ALL
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
EVO-ALL
Page 9 / 9