Addendum - 2A Town Hall Building Layout
3
1 1 2 2 3 3 4 4 5 5 A A B B C C D D PROJECT TEAM DBR ENGINEERING CONSULTINGS MEP ENGINEER THE WOODLANDS TOWNSHIP OWNER PALERMOBARR CONSTRUCTION MANAGER THEACCESSPARTNERSHIP REGISTERED ACCESSABILITY SPECALIST ROGERS MOORE ENGINEERS STRUCTURAL ENGINEER R E G I S T E R E D A R C H I T E C T S T A T E O F T E X A S M E L I S S A J. O ' N E I L 1 9 7 7 3 28 APRIL 2011 NO. DATE ISSUE PROJECT NAME THE WOODLANDS TOWNSHIP PROJECT ADDRESS 2801 TECHNOLOGY FOREST BLVD THE WOODLANDS, TEXAS 77381 PROJECT NO. CONTRACT NO. KIRKSEY PROJECT NO. 2011008 KEY PLAN SHEET TITLE LEVEL 1 FINISH PLAN - WEST SHEET NUMBER IA2.60 © 2011 Kirksey 2011008 [BIMSERVER] | 7/19/2011 | 7:32 AM CD 28 APR 2011 PRICING + CONSTRUCTION N RECEPTION 100 RECEPTIONIST/ SECURITY 110 CONFERENCE 120 CONFERENCE 122 CONFERENCE 124 COFFEE 112 BOARD MEMBER CHAMBERS 130 CONFERENCE 114 CORRIDOR 140 MOTHERS 142 STORAGE 144 BREAK AREA 146 ELECTRICAL 148 MEETING ROOM 150 MEETING ROOM 152 CORRIDOR 160 CORRIDOR 170 CONFERENCE 172 CORRIDOR 174 WOMENS 180 MENS 182 CORRIDOR 126 CORRIDOR 200 CORRIDOR 202 CONFERENCE 204 COMMONS 210 BREAK 220 CORRIDOR 230 CORRIDOR 232 CORRIDOR 234 OPEN 235 LA MGR 236 CVB/CR STORAGE 240 CVB/CR WORKROOM 244 HR 246 STORAGE 250 JAN. CLOSET 252 HR 254 HR 256 MGT ANALY 260 WAITING 264 PRES 266 CORRIDOR 270 CR MGT 272 HR FILES 274 CVB PRES 275 HR DIR 276 ELECTRICAL 277 COFFEE/COPY 278 HR CONSULT. 288 CORRIDOR 300 FIN 310 FIN 312 FIN 314 REC CENTRAL FILES 330 CORRIDOR 332 REC MGR. 334 FIN 340 FIN 342 FIN 370 FIN 372 AGM FIN 374 AV CLOSET 135 MATCH LINE CPT-1 CPT-1 CPT-1 CPT-1 CPT-1 CT-1 2 CT-5 2 3 CPT-1 CT-1 3 2 P-4 CT-5 2 VCT-1 VCT-3 VCT-2 1 CPT-1 1 CPT-1 1 CPT-1 CPT-1 2 CT-2 B-3 B-3 B-3 5 5 B-3 CT-2 CPT-1 2 B-3 B-3 CPT-1 CPT-1 CPT-1 CPT-1 VCT-2 1 VCT-3 6 VCT-1 CPT-1 1 CPT-1 CPT-1 1 1 RF-1 RF-2 RF-3 7 CPT-1 1 4 VCT-1 CPT-1 1 6 VCT-1 CPT-1 1 9 VCT-2 10 10 P-4 ALIGN ALIGN 13 1 10 ALIGN ALIGN ALIGN ALIGN ALIGN ALIGN ALIGN WD-1 P-2 P-2 P-2 P-2 P-3 P-2 CT-4 CT-3 CT-3 CT-3 CT-3 CT-4 P-2 P-2 P-2 P-2 P-2 P-2 P-3 P-3 WD-1 F I N I S H S C H E D U L E *provide 10% attic stock of all carpet tile, floor and wall tile, ceiling tile, paint, VCT, base and rubber flooring* Flooring CPT-1 B-1 Base Decription: Rubber Base (Used with CPT-1 and VCT) Manufacturer: Allstate Color: A93 Size: 2 1/2" use straight base at carpet and coved at VCT Note: Provide Rolled Goods Description: Carpet Tile, Install with releasable glue. Manufacturer: Lee's Style: Braided Stream #GT047 Color: #404 Aged Eucalyptus Face Yarn: Antron Legacy Nylon, type 6.6 Gauge: 1/12 Dye Method: Yarn Dyed Backing: Encycle Modular by Lee's - 100% PVC Free Thermoplastic Composite Size: 24" x 24" Note: Contractor to verify installation pattern w/Architect prior to starting the installation. P-1 Description: Paint (Typical) Manufacturer: Benjamin Moore Color: Distant Gray #OC-68 Finish: Eggshell Note: Provide a 10' X 10' mockup in space for Designer's approval prior to ordering paint VCT-1 Description: Vinyl Composition Tile Manufacturer: Mannington Commercial Pattern: Solidpoint Premium Visual Tile Color: 339 Chocolate Fudge Size: 12" x 12" VCT-2 Description: Vinyl Composition Tile Manufacturer: Mannington Commercial Pattern: Solid Point Color: 343 Citrine Size: 12" x 12" P-3 Description: Paint (Accent) Manufacturer: Benjamin Moore Color: Old Salem Gray #HC-94 Finish: Eggshell Note: Provide a 10' x 10' mockup in space for Designer's approval prior to ordering paint. Walls B-2 Decription: Rubber Base (Used with rubber flooring) Manufacturer: Roppe Color: 194 Burnt Umber Size: 2 1/2" cove base Note: Provide Rolled Goods PL-1 Description: Plastic Laminate (millwork) Manufacturer: Wilsonart Color: #7919K-78 Amber Cherry Finish: Matte finish Miscellaneous P-2 Description: Paint (Accent) Manufacturer: Benjamin Moore Color: Maryville Brown #HC-75 Finish: Eggshell Note: Provide a 10' X 10' mockup in space for Designer's approval prior to ordering paint SS-1 Description: Solid Surfacing (Millwork Counter Tops) Manufacturer: Silestone Color: Blanco Dune Finish: Polished VCT-3 Description: Vinyl Composition Tile Manufacturer: Armstrong Pattern: Static Dissipative Tile Color: #51955 Moss Green Size: 12" x 12" RF-1 Description: Cork-Rubber Flooring Manufacturer: Expanko Pattern: XCR Color: #XCR41022 Forest Floor Size: 24" x 24" Note: Use manufacturer's recommended adhesives. RF-2 Description: Cork-Rubber Flooring Manufacturer: Expanko Pattern: XCR Color: #XCR41017 Saddle Brown Size: 24" x 24" Note:Use manufacturer's recommended adhesives. RF-3 Description: Cork-Rubber Flooring Manufacturer: Expanko Pattern: XCR Color: #XCR41004 Mint Julep Size: 24" x 24" Note:Use manufacturer's recommended adhesives. Ceramic Tile CT-1 Description: Ceramic Tile, rectified (entry flooring) Manufacturer: Porcelanosa Style: Block #V51215031 Color: Wenge, matte finish Size: 6" x 26" with 1/16" grout joint Note:Use manufacturer's recommended adhesives. Use a self- bonding, sheet applied eslastomeric membrane, 1/16" thick from NAC, ECB anti fracture membrane, contact 1-800-633 4622 CT-2 Description: Porcelain Tile (restroom flooring) Manufacturer: Dal Tile Style: Veranda Color: #P522 Patina Size: 6 1/2" x 20" with 1/16" grout joint Note: Install in an ashlar pattern. CT-3 Description: Glass Tile (restroom accent tile) Manufacturer: Dal Tile Style: Mosaic Tile Color: #P66 Rainforest Blend Size: 1" x 1" Note: Install with a white backer. CT-4 Description: Porcelain Tile (restroom wall tile) Manufacturer: Dal Tile Style: Rittenhouse Square Color: #K775 Matte Biscuit Size: 3" x 6" Note: Install in an ashlar pattern. CT-5 Description: Stone Mosaics (corridor accent floor tile) Manufacturer: Walker Zanger Style: Zen Garden Color: #2ZGATWH12 Size:12" x 12" Note: Install using white multi-purpose thin set & sanded epoxy grout. Use a sealer on the stones. CT-6 Description: Glass Tile (break room backsplash) Manufacturer: Surfaces Unlimited Style: Vision Glass Color: #EV-03 Brown Flicker Size:1" x 4" Note: Install using a white backer. B-3 Decription: Ceramic Tile Cove Base (Used in restrooms) Manufacturer: Dal Tile Pattern: Veranda Color: #P522 Patina Size: #S-36E9T 6" x 13" PL-2 Description: Plastic Laminate (millwork uppers & lowers) Manufacturer: Pionite Color: #SG209 Putty Gray Finish: Suede finish SS-2 Description: Solid Surfacing (Transaction Tops) Manufacturer: Corian Color: Earth Finish: Polished Description: Wood Mosaics (Accent Wall) Manufacturer: Porcelanosa Pattern: Mosaics Brick Wood #L106200061 Size: 273 mm wide x 280 mm length x 10 mm thick Note: Install tiles without joints and use manufacturer's recommended adhesives. WD-1 Description: Glass (Accent Wall) Description: 1/4" thick tempered glass, back painted Paint: MDC Wall Finishes, Liqua Pearl, #L91013, pearl/metallic finish, water based Note: Paint contact, Lindsey Forster 713-679-8164 GL-1 Description: Cast Glass (Reception Desk) Manufacturer: Pulp Studios Pattern: #1036 Size: Maximum dimensions 44" x 110" Note: Contact 310-815-4999 GL-2 P-4 Description: Paint (Accent) Manufacturer: Benjamin Moore Color: Van Buren Brown #HC-70 Finish: Eggshell Note: Provide a 10' x 10' mockup in space for Designer's approval prior to ordering paint. B-4 Decription: Tile base Manufacturer: Porcelanosa Pattern: Block, bullnose base Color: Wenge Size: 4" x 17" Description: Paint (Accent in Breakroom) Manufacturer: Benjamin Moore Color: Henderson Buff #HC-15 Finish: Eggshell Note: Provide a 10' x 10' mockup in space for Designer's approval prior to ordering paint. P-5 Description: Wallcovering (Skyfold) Manufacturer: Maharam Pattern: Measure #399505 Unbacked Color: #007 Root Contents: 61% Polyolefin, 39% Post-Consumer Recycled Polyster Width: 54" WC-1 Description: Frosted Film applied to glass Note: Provide samples to Architect for approval/selection Contact: Foxmark, Jamie Garza, 713-329-5423 FF-1 Description: Graphic (neighborhood maps) printed on film and applied to glass Note: Contact: Foxmark, Jamie Garza, 713-329-5423 FF-2 Description: Tile Flooring Manufacturer: Dal Tile Color: D109 Architectural Gray Size:1" x 1" Note: Install using white multi-purpose thin set & sanded epoxy grout. CT-7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 G E N E R A L N O T E S P L A N N O T E S Provide vinyl transition strip between carpet and VCT. Vinyl strip to match Roppe 147 Light Brown. Refer to details on IA9.10 A. Refer to Project Information Sheet for legend of Reference Symbols and other graphic indicators/symbols.. B. Refer to elevations for scheduled finishes. C. Refer to reflected ceiling plan for ceiling grid and tile specifications and finishes. D. Refer to door schedule for door and frame finishes. E. All surfaces which are to receive finishes are to be clean, true and free from irregularities. F. Existing base building restrooms, stairwells, janitor closets and other core elements are not in contract, unless otherwise noted (shown hatched). G. Contractor to submit two samples of each finish to architect for approval. Submittals to be identified with finish code, name, date, number, formula, sheen and texture as required. Contractor to place full order only after written approval of acceptance is received. Adequate time shall be allowed for review and re - submittal as required. H. No substitutions of grade, quality, or manufacturer shall be allowed without written approval from the Architect or Tenant. J. Carpet shall lay in same direction unless shown otherwise. Carpet to receive a minimum of seams with no cross-joints. Avoid seaming near doors and corners. Contractor shall provide two copies of seaming submittals to Architect for approval prior to placing order. Carpet shall be trimmed evenly and neatly for a tight fit at walls, projections, trim strips or reveals. Final installation shall be free from ripples and punctures and per manufacturer's and industry standards. Architect shall make final determination. K. Transition between two dissimilar floor finishes is to occur at the centerline of door or cased opening, unless otherwise noted. Float floor as required so top of finishes are flush. Install rubber trim strips at transition between carpet and resilient tile. Color to match base. L. All VCT to be cleaned and waxed prior to final punch list. M. Refer to manufacturer's instructions for temperature of surfaces to be painted and surrounding air. Do not apply materials when relative humidity exceeds 85% and do not apply to damp or wet surfaces. N. All carpeted areas to be cleaned and vacuumed prior to final inspection. All VCT, wood, tile, stone, sealed concrete or other hard surface floor finishes to be cleaned and waxed prior to final inspection. P. All floors to be Cpt-1, unless noted otherwise. Q. All base to be B-1, unless noted otherwise. R. All walls to be P-1, unless noted otherwise. S. All suspended drywall ceilings to be painted to match adjacent ceiling tiles. T. All reveal conditions to be painted to match adjacent walls, unless otherwise noted. U. Graphics and Signage installed by others, unless noted otherwise. V. VOC levels must not exceed specified limits for all paints, coatings, adhesives and sealants. See VOC Requirements on page IA0.10. W. Same as note 4 under LEED requirments on page IA0.10. Provide metal Schluter strip between carpet and ceramic tile floor. Refer to details on IA9.10. Install ceramic tile in an ashlar pattern. Install base B-2 at all cork-rubber flooring. Install base B-3 in this room. Install VCT over plywood decking and between rails of high density shelving. Install RF-1 (24"W), RF-2 (24"W) and RF-3 (3"W) in alternating stripes. Stripes to run perpendicular to the window wall. Accent paint color to end at glass frame. Install VCT in a 24" x 24" checkerboard pattern. Refer to elevations for exact finish locations. Existing finishes to remain. ADD ALTERNATE #6: Purchase carpet CPT-1 for this area, but do not install. Stain existing concrete to match CT-2. Seal concrete after it has been stained. Refer to A4/IA9.13 for flush base detail of B-4 base. Refer to C3/IA9.10 for end partition detail of scheduled tile wrapping corner. Install CT-4 on all wet wall locations in the shower enclosure (three sides on wall and ceiling). Install schluter trim (detail C3/IA9.10) on all corner conditions. Provide full height schluter trim where wall and ceiling enclosure stops at gyp. bd. beyond shower. Provide CT-7 on showing flooring enclosure. B5 LEVEL 1 FINISH PLAN SCALE: 1/8" = 1'-0"
Transcript of Addendum - 2A Town Hall Building Layout
1
1
2
2
3
3
4
4
5
5
A A
B B
C C
D DPROJECT TEAM
DBR ENGINEERINGCONSULTINGSMEP ENGINEER
THE WOODLANDS TOWNSHIPOWNER
PALERMOBARRCONSTRUCTION MANAGER
THEACCESSPARTNERSHIPREGISTERED ACCESSABILITY SPECALIST
ROGERS MOORE ENGINEERSSTRUCTURAL ENGINEER
REG ISTERED ARCHITECT
STATE O F TEXAS
MELISSA J. O 'NEIL
19773
28 APRIL 2011
NO. DATE ISSUE
PROJECT NAME
THE WOODLANDS TOWNSHIP
PROJECT ADDRESS
2801 TECHNOLOGY FORESTBLVDTHE WOODLANDS, TEXAS77381 PROJECT NO.
CONTRACT NO.
KIRKSEY PROJECT NO. 2011008KEY PLAN
SHEET TITLE
LEVEL 1 FINISH PLAN - WEST
SHEET NUMBER
IA2.60© 2011 Kirksey
2011
008
[BIM
SER
VER
] | 7
/19/
2011
| 7:
32 A
M
CD 28 APR 2011 PRICING + CONSTRUCTION
N
RECEPTION100
RECEPTIONIST/SECURITY
110
CONFERENCE120
CONFERENCE122
CONFERENCE124
COFFEE112
BOARD MEMBERCHAMBERS
130
CONFERENCE114
CORRIDOR140
MOTHERS142
STORAGE144
BREAK AREA146
ELECTRICAL148
MEETING ROOM150
MEETING ROOM152
CORRIDOR160
CORRIDOR170
CONFERENCE172
CORRIDOR174
WOMENS180
MENS182
CORRIDOR126
CORRIDOR200
CORRIDOR202
CONFERENCE204
COMMONS210
BREAK220
CORRIDOR230
CORRIDOR232
CORRIDOR234
OPEN235
LA MGR236
CVB/CRSTORAGE
240
CVB/CRWORKROOM
244HR246
STORAGE250
JAN. CLOSET252
HR254
HR256
MGT ANALY260
WAITING264
PRES266
CORRIDOR270
CR MGT272
HR FILES274
CVB PRES275
HR DIR276 ELECTRICAL
277 COFFEE/COPY278
HR CONSULT.288
CORRIDOR300
FIN310
FIN312
FIN314
REC CENTRALFILES
330
CORRIDOR332
REC MGR.334
FIN340
FIN342
FIN370
FIN372
AGM FIN374
AV CLOSET135
MATC
H LIN
E
CPT-1
CPT-1
CPT-1
CPT-1 CPT-1
CT-1
2 CT-5
2
3
CPT-1 CT-1
3
2
P-4
CT-5
2
VCT-1
VCT-3
VCT-2
1
CPT-1
1
CPT-1 1
CPT-1
CPT-1 2
CT-2
B-3
B-3
B-3
5 5
B-3 CT-2
CPT-1 2
B-3
B-3
CPT-1
CPT-1
CPT-1
CPT-1
VCT-2
1
VCT-3
6
VCT-1
CPT-1
1
CPT-1 CPT-1 1 1 RF-1
RF-2
RF-3
7
CPT-1 1
4
VCT-1
CPT-1 1
6
VCT-1
CPT-1 1
9 VCT-2
10
10
P-4ALIGNALIGN
13 1
10
ALIGNALIGNALIG
N
ALIG
N
ALIGN
ALIGN
ALIG
N
WD-1
P-2 P-2 P-2
P-2
P-3
P-2
CT-4
CT-3
CT-3 CT-3
CT-3
CT-4
P-2
P-2
P-2
P-2
P-2
P-2
P-3
P-3
WD-1
F I N I S H S C H E D U L E *provide 10% attic stock of all carpet tile, floor and wall tile, ceiling tile, paint, VCT, base and rubber flooring*FlooringCPT-1 B-1
BaseDecription: Rubber Base (Used with CPT-1 and VCT)Manufacturer: AllstateColor: A93Size: 2 1/2" use straight base at carpet and coved at VCTNote: Provide Rolled Goods
Description: Carpet Tile, Install with releasable glue.Manufacturer: Lee'sStyle: Braided Stream #GT047Color: #404 Aged EucalyptusFace Yarn: Antron Legacy Nylon, type 6.6Gauge: 1/12Dye Method: Yarn DyedBacking: Encycle Modular by Lee's - 100% PVC FreeThermoplastic CompositeSize: 24" x 24"Note: Contractor to verify installation patternw/Architect prior to starting the installation.
P-1 Description: Paint (Typical)Manufacturer: Benjamin MooreColor: Distant Gray #OC-68Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
VCT-1 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solidpoint Premium Visual TileColor: 339 Chocolate FudgeSize: 12" x 12"
VCT-2 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solid PointColor: 343 CitrineSize: 12" x 12"
P-3 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Old Salem Gray #HC-94Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
Walls
B-2 Decription: Rubber Base (Used with rubber flooring)Manufacturer: RoppeColor: 194 Burnt UmberSize: 2 1/2" cove baseNote: Provide Rolled Goods
PL-1 Description: Plastic Laminate (millwork)Manufacturer: WilsonartColor: #7919K-78 Amber CherryFinish: Matte finish
Miscellaneous
P-2 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Maryville Brown #HC-75Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
SS-1
Description: Solid Surfacing (Millwork Counter Tops)Manufacturer: SilestoneColor: Blanco DuneFinish: PolishedVCT-3 Description: Vinyl Composition Tile
Manufacturer: ArmstrongPattern: Static Dissipative TileColor: #51955 Moss GreenSize: 12" x 12"
RF-1 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41022 Forest FloorSize: 24" x 24"Note: Use manufacturer's recommended adhesives.
RF-2 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41017 Saddle BrownSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
RF-3 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41004 Mint JulepSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
Ceramic TileCT-1 Description: Ceramic Tile, rectified (entry flooring)
Manufacturer: PorcelanosaStyle: Block #V51215031Color: Wenge, matte finishSize: 6" x 26" with 1/16" grout jointNote:Use manufacturer's recommended adhesives.Use a self- bonding, sheet applied eslastomeric membrane,1/16" thick from NAC, ECB anti fracture membrane,contact 1-800-633 4622
CT-2 Description: Porcelain Tile (restroom flooring)Manufacturer: Dal TileStyle: VerandaColor: #P522 PatinaSize: 6 1/2" x 20" with 1/16" grout jointNote: Install in an ashlar pattern.
CT-3 Description: Glass Tile (restroom accent tile)Manufacturer: Dal TileStyle: Mosaic TileColor: #P66 Rainforest BlendSize: 1" x 1"Note: Install with a white backer.
CT-4 Description: Porcelain Tile (restroom wall tile)Manufacturer: Dal TileStyle: Rittenhouse SquareColor: #K775 Matte BiscuitSize: 3" x 6"Note: Install in an ashlar pattern.
CT-5 Description: Stone Mosaics (corridor accent floor tile)Manufacturer: Walker ZangerStyle: Zen GardenColor: #2ZGATWH12Size:12" x 12"Note: Install using white multi-purpose thin set &sanded epoxy grout. Use a sealer on the stones.
CT-6 Description: Glass Tile (break room backsplash)Manufacturer: Surfaces UnlimitedStyle: Vision GlassColor: #EV-03 Brown FlickerSize:1" x 4"Note: Install using a white backer.
B-3 Decription: Ceramic Tile Cove Base (Used in restrooms)Manufacturer: Dal TilePattern: VerandaColor: #P522 PatinaSize: #S-36E9T 6" x 13"
PL-2 Description: Plastic Laminate (millwork uppers & lowers)Manufacturer: PioniteColor: #SG209 Putty GrayFinish: Suede finish
SS-2
Description: Solid Surfacing (Transaction Tops)Manufacturer: CorianColor: EarthFinish: Polished
Description: Wood Mosaics (Accent Wall)Manufacturer: PorcelanosaPattern: Mosaics Brick Wood #L106200061Size: 273 mm wide x 280 mm length x 10 mm thickNote: Install tiles without joints and use manufacturer'srecommended adhesives.
WD-1
Description: Glass (Accent Wall)Description: 1/4" thick tempered glass, back paintedPaint: MDC Wall Finishes, Liqua Pearl, #L91013,pearl/metallic finish, water basedNote: Paint contact, Lindsey Forster 713-679-8164
GL-1
Description: Cast Glass (Reception Desk)Manufacturer: Pulp StudiosPattern: #1036Size: Maximum dimensions 44" x 110"Note: Contact 310-815-4999
GL-2
P-4 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Van Buren Brown #HC-70Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
B-4 Decription: Tile baseManufacturer: PorcelanosaPattern: Block, bullnose baseColor: WengeSize: 4" x 17"
Description: Paint (Accent in Breakroom)Manufacturer: Benjamin MooreColor: Henderson Buff #HC-15Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
P-5
Description: Wallcovering (Skyfold)Manufacturer: MaharamPattern: Measure #399505 UnbackedColor: #007 RootContents: 61% Polyolefin, 39% Post-Consumer Recycled PolysterWidth: 54"
WC-1
Description: Frosted Film applied to glassNote: Provide samples to Architect for approval/selectionContact: Foxmark, Jamie Garza, 713-329-5423
FF-1
Description: Graphic (neighborhood maps) printed on filmand applied to glassNote: Contact: Foxmark, Jamie Garza, 713-329-5423
FF-2
Description: Tile FlooringManufacturer: Dal TileColor: D109 Architectural GraySize:1" x 1"Note: Install using white multi-purpose thin set & sandedepoxy grout.
CT-7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
G E N E R A L N O T E S P L A N N O T E SProvide vinyl transition strip between carpet and VCT. Vinyl stripto match Roppe 147 Light Brown. Refer to details on IA9.10
A. Refer to Project Information Sheet for legend of Reference Symbols and other graphic indicators/symbols..B. Refer to elevations for scheduled finishes.C. Refer to reflected ceiling plan for ceiling grid and tile specifications and finishes.D. Refer to door schedule for door and frame finishes.E. All surfaces which are to receive finishes are to be clean, true and free from irregularities.F. Existing base building restrooms, stairwells, janitor closets and other core elements are not in contract, unless otherwise noted (shown hatched).G. Contractor to submit two samples of each finish to architect for approval. Submittals to be identified with finish code, name, date, number, formula, sheen and texture asrequired. Contractor to place full order only after written approval of acceptance is received. Adequate time shall be allowed for review and re - submittal as required.H. No substitutions of grade, quality, or manufacturer shall be allowed without written approval from the Architect or Tenant.J. Carpet shall lay in same direction unless shown otherwise. Carpet to receive a minimum of seams with no cross-joints. Avoid seaming near doors and corners.Contractor shall provide two copies of seaming submittals to Architect for approval prior to placing order. Carpet shall be trimmed evenly and neatly for a tight fit at walls,projections, trim strips or reveals. Final installation shall be free from ripples and punctures and per manufacturer's and industry standards. Architect shall make finaldetermination.K. Transition between two dissimilar floor finishes is to occur at the centerline of door or cased opening, unless otherwise noted. Float floor as required so top of finishes areflush. Install rubber trim strips at transition between carpet and resilient tile. Color to match base.L. All VCT to be cleaned and waxed prior to final punch list.M. Refer to manufacturer's instructions for temperature of surfaces to be painted and surrounding air. Do not apply materials when relative humidity exceeds 85% and do notapply to damp or wet surfaces.N. All carpeted areas to be cleaned and vacuumed prior to final inspection. All VCT, wood, tile, stone, sealed concrete or other hard surface floor finishes to be cleaned andwaxed prior to final inspection.P. All floors to be Cpt-1, unless noted otherwise.Q. All base to be B-1, unless noted otherwise.R. All walls to be P-1, unless noted otherwise.S. All suspended drywall ceilings to be painted to match adjacent ceiling tiles.T. All reveal conditions to be painted to match adjacent walls, unless otherwise noted.U. Graphics and Signage installed by others, unless noted otherwise.V. VOC levels must not exceed specified limits for all paints, coatings, adhesives and sealants. See VOC Requirements on page IA0.10.W. Same as note 4 under LEED requirments on page IA0.10.
Provide metal Schluter strip between carpet and ceramic tile floor.Refer to details on IA9.10.Install ceramic tile in an ashlar pattern.
Install base B-2 at all cork-rubber flooring.
Install base B-3 in this room.Install VCT over plywood decking and between rails of highdensity shelving.Install RF-1 (24"W), RF-2 (24"W) and RF-3 (3"W) in alternating stripes.Stripes to run perpendicular to the window wall.Accent paint color to end at glass frame.
Install VCT in a 24" x 24" checkerboard pattern.
Refer to elevations for exact finish locations.
Existing finishes to remain.
ADD ALTERNATE #6: Purchase carpet CPT-1 for this area, but do not install.Stain existing concrete to match CT-2. Seal concrete after it hasbeen stained.Refer to A4/IA9.13 for flush base detail of B-4 base.
Refer to C3/IA9.10 for end partition detail of scheduled tile wrapping corner.
Install CT-4 on all wet wall locations in the shower enclosure (three sides on walland ceiling). Install schluter trim (detail C3/IA9.10) on all corner conditions. Providefull height schluter trim where wall and ceiling enclosure stops at gyp. bd. beyond shower. Provide CT-7 on showing flooring enclosure.
B5LEVEL 1 FINISH PLANSCALE: 1/8" = 1'-0"
1
1
2
2
3
3
4
4
5
5
A A
B B
C C
D DPROJECT TEAM
DBR ENGINEERINGCONSULTINGSMEP ENGINEER
THE WOODLANDS TOWNSHIPOWNER
PALERMOBARRCONSTRUCTION MANAGER
THEACCESSPARTNERSHIPREGISTERED ACCESSABILITY SPECALIST
ROGERS MOORE ENGINEERSSTRUCTURAL ENGINEER
REG ISTERED ARCHITECT
STATE O F TEXAS
MELISSA J. O 'NEIL
19773
28 APRIL 2011
NO. DATE ISSUE
PROJECT NAME
THE WOODLANDS TOWNSHIP
PROJECT ADDRESS
2801 TECHNOLOGY FORESTBLVDTHE WOODLANDS, TEXAS77381 PROJECT NO.
CONTRACT NO.
KIRKSEY PROJECT NO. 2011008KEY PLAN
SHEET TITLE
LEVEL 1 FINISH PLAN - EAST
SHEET NUMBER
IA2.61© 2011 Kirksey
2011
008
[BIM
SER
VER
] | 7
/19/
2011
| 7:
32 A
M
CD 28 APR 2011 PRICING + CONSTRUCTION
N
FIN310
FIN312
FIN314
FIN340
FIN342
FIN370
FIN372
AGM FIN374
CORRIDOR380
CONFERENCE382
FS DIR384
COPY/PRINT386
CORRIDOR400
CONFERENCE410
CONFERENCE412
CAD MGR414
CAD MGR416
WOMENS402
MENS404
CORRIDOR406
CONFERENCE420
PRINT/COPY422
ENTRY500
CORRIDOR508
IT SERVER512
CORRIDOR514
CONFERENCE516
MAIL/PRODUCTION
520MAIL522
COFFEE610
NS MGR.612
AMBASSADORS640
CORRIDOR642
EMPLOYEE ENTRY643
EMPLOYEE ENTRYVESTIBULE
644
CORRIDOR645
NS WORKROOM646
CORRIDOR628
IT DIR634
IT STORAGE636
CONFERENCE650
CAD DIR656
AGM CS658
CORRIDOR659
LE DIR662
PARD DIR664
A PARD DIR666
PARD BD MGR667
PARD FAC SUPER668
PARD FM SPEC668
STORAGE670
CLOSET672
STORAGE673
TELEPHONE674
ELECTRICAL675
SECURE STORAGE676
PC BUILD ROOM510
MATC
H LIN
E
MATCH LINE
CT-5
2
8
CPT-1
CPT-1
5 B-3
CT-2
B-3
CT-2
B-3
B-3 5
B-3 B-3
VCT-1
CPT-1 1
VCT-2 9
CPT-1
CT-1
3
2
CPT-1
10
10
VCT-3
CPT-1 1
CPT-1 1
CT-1
3
VCT-1
CPT-1
1
CT-1
3
CPT-1 2
2
11
11
11
11
11
11
11
12
10
ALIGN
ALIG
N
ALIGN
B-4
B-4
14
14
B-4 14
15
15
15
15
CPT-1
P-2
P-2
P-2
CT-3
CT-4
CT-4
CT-3
CT-3 CT-3
P-2 P-2
P-2
WD-1 GL-1
P-3
P-3
P-2
P-3
P-2
P-2
F I N I S H S C H E D U L E *provide 10% attic stock of all carpet tile, floor and wall tile, ceiling tile, paint, VCT, base and rubber flooring*FlooringCPT-1 B-1
BaseDecription: Rubber Base (Used with CPT-1 and VCT)Manufacturer: AllstateColor: A93Size: 2 1/2" use straight base at carpet and coved at VCTNote: Provide Rolled Goods
Description: Carpet Tile, Install with releasable glue.Manufacturer: Lee'sStyle: Braided Stream #GT047Color: #404 Aged EucalyptusFace Yarn: Antron Legacy Nylon, type 6.6Gauge: 1/12Dye Method: Yarn DyedBacking: Encycle Modular by Lee's - 100% PVC FreeThermoplastic CompositeSize: 24" x 24"Note: Contractor to verify installation patternw/Architect prior to starting the installation.
P-1 Description: Paint (Typical)Manufacturer: Benjamin MooreColor: Distant Gray #OC-68Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
VCT-1 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solidpoint Premium Visual TileColor: 339 Chocolate FudgeSize: 12" x 12"
VCT-2 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solid PointColor: 343 CitrineSize: 12" x 12"
P-3 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Old Salem Gray #HC-94Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
Walls
B-2 Decription: Rubber Base (Used with rubber flooring)Manufacturer: RoppeColor: 194 Burnt UmberSize: 2 1/2" cove baseNote: Provide Rolled Goods
PL-1 Description: Plastic Laminate (millwork)Manufacturer: WilsonartColor: #7919K-78 Amber CherryFinish: Matte finish
Miscellaneous
P-2 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Maryville Brown #HC-75Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
SS-1
Description: Solid Surfacing (Millwork Counter Tops)Manufacturer: SilestoneColor: Blanco DuneFinish: PolishedVCT-3 Description: Vinyl Composition Tile
Manufacturer: ArmstrongPattern: Static Dissipative TileColor: #51955 Moss GreenSize: 12" x 12"
RF-1 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41022 Forest FloorSize: 24" x 24"Note: Use manufacturer's recommended adhesives.
RF-2 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41017 Saddle BrownSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
RF-3 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41004 Mint JulepSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
Ceramic TileCT-1 Description: Ceramic Tile, rectified (entry flooring)
Manufacturer: PorcelanosaStyle: Block #V51215031Color: Wenge, matte finishSize: 6" x 26" with 1/16" grout jointNote:Use manufacturer's recommended adhesives.Use a self- bonding, sheet applied eslastomeric membrane,1/16" thick from NAC, ECB anti fracture membrane,contact 1-800-633 4622
CT-2 Description: Porcelain Tile (restroom flooring)Manufacturer: Dal TileStyle: VerandaColor: #P522 PatinaSize: 6 1/2" x 20" with 1/16" grout jointNote: Install in an ashlar pattern.
CT-3 Description: Glass Tile (restroom accent tile)Manufacturer: Dal TileStyle: Mosaic TileColor: #P66 Rainforest BlendSize: 1" x 1"Note: Install with a white backer.
CT-4 Description: Porcelain Tile (restroom wall tile)Manufacturer: Dal TileStyle: Rittenhouse SquareColor: #K775 Matte BiscuitSize: 3" x 6"Note: Install in an ashlar pattern.
CT-5 Description: Stone Mosaics (corridor accent floor tile)Manufacturer: Walker ZangerStyle: Zen GardenColor: #2ZGATWH12Size:12" x 12"Note: Install using white multi-purpose thin set &sanded epoxy grout. Use a sealer on the stones.
CT-6 Description: Glass Tile (break room backsplash)Manufacturer: Surfaces UnlimitedStyle: Vision GlassColor: #EV-03 Brown FlickerSize:1" x 4"Note: Install using a white backer.
B-3 Decription: Ceramic Tile Cove Base (Used in restrooms)Manufacturer: Dal TilePattern: VerandaColor: #P522 PatinaSize: #S-36E9T 6" x 13"
PL-2 Description: Plastic Laminate (millwork uppers & lowers)Manufacturer: PioniteColor: #SG209 Putty GrayFinish: Suede finish
SS-2
Description: Solid Surfacing (Transaction Tops)Manufacturer: CorianColor: EarthFinish: Polished
Description: Wood Mosaics (Accent Wall)Manufacturer: PorcelanosaPattern: Mosaics Brick Wood #L106200061Size: 273 mm wide x 280 mm length x 10 mm thickNote: Install tiles without joints and use manufacturer'srecommended adhesives.
WD-1
Description: Glass (Accent Wall)Description: 1/4" thick tempered glass, back paintedPaint: MDC Wall Finishes, Liqua Pearl, #L91013,pearl/metallic finish, water basedNote: Paint contact, Lindsey Forster 713-679-8164
GL-1
Description: Cast Glass (Reception Desk)Manufacturer: Pulp StudiosPattern: #1036Size: Maximum dimensions 44" x 110"Note: Contact 310-815-4999
GL-2
P-4 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Van Buren Brown #HC-70Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
B-4 Decription: Tile baseManufacturer: PorcelanosaPattern: Block, bullnose baseColor: WengeSize: 4" x 17"
Description: Paint (Accent in Breakroom)Manufacturer: Benjamin MooreColor: Henderson Buff #HC-15Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
P-5
Description: Wallcovering (Skyfold)Manufacturer: MaharamPattern: Measure #399505 UnbackedColor: #007 RootContents: 61% Polyolefin, 39% Post-Consumer Recycled PolysterWidth: 54"
WC-1
Description: Frosted Film applied to glassNote: Provide samples to Architect for approval/selectionContact: Foxmark, Jamie Garza, 713-329-5423
FF-1
Description: Graphic (neighborhood maps) printed on filmand applied to glassNote: Contact: Foxmark, Jamie Garza, 713-329-5423
FF-2
Description: Tile FlooringManufacturer: Dal TileColor: D109 Architectural GraySize:1" x 1"Note: Install using white multi-purpose thin set & sandedepoxy grout.
CT-7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
G E N E R A L N O T E S P L A N N O T E SProvide vinyl transition strip between carpet and VCT. Vinyl stripto match Roppe 147 Light Brown. Refer to details on IA9.10
A. Refer to Project Information Sheet for legend of Reference Symbols and other graphic indicators/symbols..B. Refer to elevations for scheduled finishes.C. Refer to reflected ceiling plan for ceiling grid and tile specifications and finishes.D. Refer to door schedule for door and frame finishes.E. All surfaces which are to receive finishes are to be clean, true and free from irregularities.F. Existing base building restrooms, stairwells, janitor closets and other core elements are not in contract, unless otherwise noted (shown hatched).G. Contractor to submit two samples of each finish to architect for approval. Submittals to be identified with finish code, name, date, number, formula, sheen and texture asrequired. Contractor to place full order only after written approval of acceptance is received. Adequate time shall be allowed for review and re - submittal as required.H. No substitutions of grade, quality, or manufacturer shall be allowed without written approval from the Architect or Tenant.J. Carpet shall lay in same direction unless shown otherwise. Carpet to receive a minimum of seams with no cross-joints. Avoid seaming near doors and corners.Contractor shall provide two copies of seaming submittals to Architect for approval prior to placing order. Carpet shall be trimmed evenly and neatly for a tight fit at walls,projections, trim strips or reveals. Final installation shall be free from ripples and punctures and per manufacturer's and industry standards. Architect shall make finaldetermination.K. Transition between two dissimilar floor finishes is to occur at the centerline of door or cased opening, unless otherwise noted. Float floor as required so top of finishes areflush. Install rubber trim strips at transition between carpet and resilient tile. Color to match base.L. All VCT to be cleaned and waxed prior to final punch list.M. Refer to manufacturer's instructions for temperature of surfaces to be painted and surrounding air. Do not apply materials when relative humidity exceeds 85% and do notapply to damp or wet surfaces.N. All carpeted areas to be cleaned and vacuumed prior to final inspection. All VCT, wood, tile, stone, sealed concrete or other hard surface floor finishes to be cleaned andwaxed prior to final inspection.P. All floors to be Cpt-1, unless noted otherwise.Q. All base to be B-1, unless noted otherwise.R. All walls to be P-1, unless noted otherwise.S. All suspended drywall ceilings to be painted to match adjacent ceiling tiles.T. All reveal conditions to be painted to match adjacent walls, unless otherwise noted.U. Graphics and Signage installed by others, unless noted otherwise.V. VOC levels must not exceed specified limits for all paints, coatings, adhesives and sealants. See VOC Requirements on page IA0.10.W. Same as note 4 under LEED requirments on page IA0.10.
Provide metal Schluter strip between carpet and ceramic tile floor.Refer to details on IA9.10.Install ceramic tile in an ashlar pattern.
Install base B-2 at all cork-rubber flooring.
Install base B-3 in this room.Install VCT over plywood decking and between rails of highdensity shelving.Install RF-1 (24"W), RF-2 (24"W) and RF-3 (3"W) in alternating stripes.Stripes to run perpendicular to the window wall.Accent paint color to end at glass frame.
Install VCT in a 24" x 24" checkerboard pattern.
Refer to elevations for exact finish locations.
Existing finishes to remain.
ADD ALTERNATE #6: Purchase carpet CPT-1 for this area, but do not install.Stain existing concrete to match CT-2. Seal concrete after it hasbeen stained.Refer to A4/IA9.13 for flush base detail of B-4 base.
Refer to C3/IA9.10 for end partition detail of scheduled tile wrapping corner.
Install CT-4 on all wet wall locations in the shower enclosure (three sides on walland ceiling). Install schluter trim (detail C3/IA9.10) on all corner conditions. Providefull height schluter trim where wall and ceiling enclosure stops at gyp. bd. beyond shower. Provide CT-7 on showing flooring enclosure.
B5LEVEL 1 FINISH PLANSCALE: 1/8" = 1'-0"
1
1
2
2
3
3
4
4
5
5
A A
B B
C C
D DPROJECT TEAM
DBR ENGINEERINGCONSULTINGSMEP ENGINEER
THE WOODLANDS TOWNSHIPOWNER
PALERMOBARRCONSTRUCTION MANAGER
THEACCESSPARTNERSHIPREGISTERED ACCESSABILITY SPECALIST
ROGERS MOORE ENGINEERSSTRUCTURAL ENGINEER
REG ISTERED ARCHITECT
STATE O F TEXAS
MELISSA J. O 'NEIL
19773
28 APRIL 2011
NO. DATE ISSUE
PROJECT NAME
THE WOODLANDS TOWNSHIP
PROJECT ADDRESS
2801 TECHNOLOGY FORESTBLVDTHE WOODLANDS, TEXAS77381 PROJECT NO.
CONTRACT NO.
KIRKSEY PROJECT NO. 2011008KEY PLAN
SHEET TITLE
LEVEL 1 FINISH PLAN - SOUTH
SHEET NUMBER
IA2.62© 2011 Kirksey
2011
008
[BIM
SER
VER
] | 7
/19/
2011
| 7:
32 A
M
CD 28 APR 2011 PRICING + CONSTRUCTION
N
1 05 MAY 2011 ADDENDUM #1
N
1
1
CORRIDOR508
CORRIDOR628
EXPANSION710
HUDDLE722
CORRIDOR721
CORRIDOR723
OPEN800
WOMENSSHOWER
802
WOMENS804
CORRIDOR806
MENS808
MENSSHOWER
810
ELECTRICAL822
EXPANSION850
510
VCT-3 CPT-1 1
12
12
13 B-3
B-3
B-3 13
13
13
B-3
B-3
B-3
10
15 15
15 15
11 11
11
11
11 11
11
CPT-1
CPT-1
CPT-1
CPT-1
16 16
16 16
P-3
CT-3
CT-4
CT-4
CT-3
CT-3
CT-3
F I N I S H S C H E D U L E *provide 10% attic stock of all carpet tile, floor and wall tile, ceiling tile, paint, VCT, base and rubber flooring*FlooringCPT-1 B-1
BaseDecription: Rubber Base (Used with CPT-1 and VCT)Manufacturer: AllstateColor: A93Size: 2 1/2" use straight base at carpet and coved at VCTNote: Provide Rolled Goods
Description: Carpet Tile, Install with releasable glue.Manufacturer: Lee'sStyle: Braided Stream #GT047Color: #404 Aged EucalyptusFace Yarn: Antron Legacy Nylon, type 6.6Gauge: 1/12Dye Method: Yarn DyedBacking: Encycle Modular by Lee's - 100% PVC FreeThermoplastic CompositeSize: 24" x 24"Note: Contractor to verify installation patternw/Architect prior to starting the installation.
P-1 Description: Paint (Typical)Manufacturer: Benjamin MooreColor: Distant Gray #OC-68Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
VCT-1 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solidpoint Premium Visual TileColor: 339 Chocolate FudgeSize: 12" x 12"
VCT-2 Description: Vinyl Composition TileManufacturer: Mannington CommercialPattern: Solid PointColor: 343 CitrineSize: 12" x 12"
P-3 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Old Salem Gray #HC-94Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
Walls
B-2 Decription: Rubber Base (Used with rubber flooring)Manufacturer: RoppeColor: 194 Burnt UmberSize: 2 1/2" cove baseNote: Provide Rolled Goods
PL-1 Description: Plastic Laminate (millwork)Manufacturer: WilsonartColor: #7919K-78 Amber CherryFinish: Matte finish
Miscellaneous
P-2 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Maryville Brown #HC-75Finish: EggshellNote: Provide a 10' X 10' mockup in space forDesigner's approval prior to ordering paint
SS-1
Description: Solid Surfacing (Millwork Counter Tops)Manufacturer: SilestoneColor: Blanco DuneFinish: PolishedVCT-3 Description: Vinyl Composition Tile
Manufacturer: ArmstrongPattern: Static Dissipative TileColor: #51955 Moss GreenSize: 12" x 12"
RF-1 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41022 Forest FloorSize: 24" x 24"Note: Use manufacturer's recommended adhesives.
RF-2 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41017 Saddle BrownSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
RF-3 Description: Cork-Rubber FlooringManufacturer: ExpankoPattern: XCRColor: #XCR41004 Mint JulepSize: 24" x 24"Note:Use manufacturer's recommended adhesives.
Ceramic TileCT-1 Description: Ceramic Tile, rectified (entry flooring)
Manufacturer: PorcelanosaStyle: Block #V51215031Color: Wenge, matte finishSize: 6" x 26" with 1/16" grout jointNote:Use manufacturer's recommended adhesives.Use a self- bonding, sheet applied eslastomeric membrane,1/16" thick from NAC, ECB anti fracture membrane,contact 1-800-633 4622
CT-2 Description: Porcelain Tile (restroom flooring)Manufacturer: Dal TileStyle: VerandaColor: #P522 PatinaSize: 6 1/2" x 20" with 1/16" grout jointNote: Install in an ashlar pattern.
CT-3 Description: Glass Tile (restroom accent tile)Manufacturer: Dal TileStyle: Mosaic TileColor: #P66 Rainforest BlendSize: 1" x 1"Note: Install with a white backer.
CT-4 Description: Porcelain Tile (restroom wall tile)Manufacturer: Dal TileStyle: Rittenhouse SquareColor: #K775 Matte BiscuitSize: 3" x 6"Note: Install in an ashlar pattern.
CT-5 Description: Stone Mosaics (corridor accent floor tile)Manufacturer: Walker ZangerStyle: Zen GardenColor: #2ZGATWH12Size:12" x 12"Note: Install using white multi-purpose thin set &sanded epoxy grout. Use a sealer on the stones.
CT-6 Description: Glass Tile (break room backsplash)Manufacturer: Surfaces UnlimitedStyle: Vision GlassColor: #EV-03 Brown FlickerSize:1" x 4"Note: Install using a white backer.
B-3 Decription: Ceramic Tile Cove Base (Used in restrooms)Manufacturer: Dal TilePattern: VerandaColor: #P522 PatinaSize: #S-36E9T 6" x 13"
PL-2 Description: Plastic Laminate (millwork uppers & lowers)Manufacturer: PioniteColor: #SG209 Putty GrayFinish: Suede finish
SS-2
Description: Solid Surfacing (Transaction Tops)Manufacturer: CorianColor: EarthFinish: Polished
Description: Wood Mosaics (Accent Wall)Manufacturer: PorcelanosaPattern: Mosaics Brick Wood #L106200061Size: 273 mm wide x 280 mm length x 10 mm thickNote: Install tiles without joints and use manufacturer'srecommended adhesives.
WD-1
Description: Glass (Accent Wall)Description: 1/4" thick tempered glass, back paintedPaint: MDC Wall Finishes, Liqua Pearl, #L91013,pearl/metallic finish, water basedNote: Paint contact, Lindsey Forster 713-679-8164
GL-1
Description: Cast Glass (Reception Desk)Manufacturer: Pulp StudiosPattern: #1036Size: Maximum dimensions 44" x 110"Note: Contact 310-815-4999
GL-2
P-4 Description: Paint (Accent)Manufacturer: Benjamin MooreColor: Van Buren Brown #HC-70Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
B-4 Decription: Tile baseManufacturer: PorcelanosaPattern: Block, bullnose baseColor: WengeSize: 4" x 17"
Description: Paint (Accent in Breakroom)Manufacturer: Benjamin MooreColor: Henderson Buff #HC-15Finish: EggshellNote: Provide a 10' x 10' mockup in space forDesigner's approval prior to ordering paint.
P-5
Description: Wallcovering (Skyfold)Manufacturer: MaharamPattern: Measure #399505 UnbackedColor: #007 RootContents: 61% Polyolefin, 39% Post-Consumer Recycled PolysterWidth: 54"
WC-1
Description: Frosted Film applied to glassNote: Provide samples to Architect for approval/selectionContact: Foxmark, Jamie Garza, 713-329-5423
FF-1
Description: Graphic (neighborhood maps) printed on filmand applied to glassNote: Contact: Foxmark, Jamie Garza, 713-329-5423
FF-2
Description: Tile FlooringManufacturer: Dal TileColor: D109 Architectural GraySize:1" x 1"Note: Install using white multi-purpose thin set & sandedepoxy grout.
CT-7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
G E N E R A L N O T E S P L A N N O T E SProvide vinyl transition strip between carpet and VCT. Vinyl stripto match Roppe 147 Light Brown. Refer to details on IA9.10
A. Refer to Project Information Sheet for legend of Reference Symbols and other graphic indicators/symbols..B. Refer to elevations for scheduled finishes.C. Refer to reflected ceiling plan for ceiling grid and tile specifications and finishes.D. Refer to door schedule for door and frame finishes.E. All surfaces which are to receive finishes are to be clean, true and free from irregularities.F. Existing base building restrooms, stairwells, janitor closets and other core elements are not in contract, unless otherwise noted (shown hatched).G. Contractor to submit two samples of each finish to architect for approval. Submittals to be identified with finish code, name, date, number, formula, sheen and texture asrequired. Contractor to place full order only after written approval of acceptance is received. Adequate time shall be allowed for review and re - submittal as required.H. No substitutions of grade, quality, or manufacturer shall be allowed without written approval from the Architect or Tenant.J. Carpet shall lay in same direction unless shown otherwise. Carpet to receive a minimum of seams with no cross-joints. Avoid seaming near doors and corners.Contractor shall provide two copies of seaming submittals to Architect for approval prior to placing order. Carpet shall be trimmed evenly and neatly for a tight fit at walls,projections, trim strips or reveals. Final installation shall be free from ripples and punctures and per manufacturer's and industry standards. Architect shall make finaldetermination.K. Transition between two dissimilar floor finishes is to occur at the centerline of door or cased opening, unless otherwise noted. Float floor as required so top of finishes areflush. Install rubber trim strips at transition between carpet and resilient tile. Color to match base.L. All VCT to be cleaned and waxed prior to final punch list.M. Refer to manufacturer's instructions for temperature of surfaces to be painted and surrounding air. Do not apply materials when relative humidity exceeds 85% and do notapply to damp or wet surfaces.N. All carpeted areas to be cleaned and vacuumed prior to final inspection. All VCT, wood, tile, stone, sealed concrete or other hard surface floor finishes to be cleaned andwaxed prior to final inspection.P. All floors to be Cpt-1, unless noted otherwise.Q. All base to be B-1, unless noted otherwise.R. All walls to be P-1, unless noted otherwise.S. All suspended drywall ceilings to be painted to match adjacent ceiling tiles.T. All reveal conditions to be painted to match adjacent walls, unless otherwise noted.U. Graphics and Signage installed by others, unless noted otherwise.V. VOC levels must not exceed specified limits for all paints, coatings, adhesives and sealants. See VOC Requirements on page IA0.10.W. Same as note 4 under LEED requirments on page IA0.10.
Provide metal Schluter strip between carpet and ceramic tile floor.Refer to details on IA9.10.Install ceramic tile in an ashlar pattern.
Install base B-2 at all cork-rubber flooring.
Install base B-3 in this room.Install VCT over plywood decking and between rails of highdensity shelving.Install RF-1 (24"W), RF-2 (24"W) and RF-3 (3"W) in alternating stripes.Stripes to run perpendicular to the window wall.Accent paint color to end at glass frame.
Install VCT in a 24" x 24" checkerboard pattern.
Refer to elevations for exact finish locations.
Existing finishes to remain.
ADD ALTERNATE #6: Purchase carpet CPT-1 for this area, but do not install.Stain existing concrete to match CT-2. Seal concrete after it hasbeen stained.Refer to A4/IA9.13 for flush base detail of B-4 base.
Refer to C3/IA9.10 for end partition detail of scheduled tile wrapping corner.
Install CT-4 on all wet wall locations in the shower enclosure (three sides on walland ceiling). Install schluter trim (detail C3/IA9.10) on all corner conditions. Providefull height schluter trim where wall and ceiling enclosure stops at gyp. bd. beyond shower. Provide CT-7 on showing flooring enclosure.
B5LEVEL 1 FINISH PLANSCALE: 1/8" = 1'-0"
