ACPSB-P 50-60Hz MS0228B-0117dunhambush.org/source/catagory/Catologue/ACPSB-P_50-60Hz... · 2020. 2....
Transcript of ACPSB-P 50-60Hz MS0228B-0117dunhambush.org/source/catagory/Catologue/ACPSB-P_50-60Hz... · 2020. 2....
Product that perform…By people who care
- 2 -
NOMENCLATURE
6 AC P S B 435 P - HP Q P GENERAL DESCRIPTION The ACPSB-P Series with new features is suitable for hotel, office, hospital, school, factory and supermarket applications. The low noise and compact series are completely leak tested, evacuated, dehydrated and charged with refrigerant prior to shipment. HERMETIC SCROLL COMPRESSOR(S) Reliability
No contact scroll design that minimizes friction, increases volumetric efficiency and reduces vibration, thus longer service life.
Suction gas cooled motor. Low Power Consumption:
High EER. No crankcase heater required.
CLASS F INSULATION CONDENSER FAN MOTOR
Extra safety margin and longer motor life even in extreme operating conditions. IP 55 construction ensure extra motor protection (ACPSB Series 68P to 1520P). Low motor speed at 950 rpm ensures quiet condenser fan operation.
MULTIPLE COMPRESSOR (ACPSB Series 220P and above)
By cycling off compressor operation to match building load, no energy is being wasted when room load requires lesser cooling capacity.
No total shut down when servicing or repairing a faulty compressor. EFFICIENT CONDENSER COIL
Staggered row of 3/8”OD inner groove tubes with 25 to 30% more surface area guarantee better heat transfer.
Mechanically expanded into die-formed corrugated aluminum fins. Integral subcooling circuit to maximize efficiency. One or multiple thermal expansion valve promotes efficient cooling
and superheat during reverse cycle Leak and pressure tested to 450 psig.
Blank - R22 P - R407C
Blank - Standard Q - Special
Blank - Cooling Only HP - Heat Pump
Air Cooled
Packaged
Nominal Capacity (MBH) Generation
6 - 60 Hz Blank - 50Hz
S - Scroll Compressor R - Rotary Compressor Propeller Fan
Product that perform…By people who care
- 3 -
GENERAL DESCRIPTION SAFETY CONTROL
High-low pressure cutout to protect compressor from high discharge pressure and system leakage. Suction accumulator to prevent liquid flood back to the compressor during heating cycle
FULLY LEAK TESTED REFRIGERANT CIRCUIT
Compressor, condenser coil, filter drier, sight glass, thermo-expansion valve, distributor and evaporator coil is brazed in complete sealed loop.
Leak and pressure tested at 450 psig. Pressure ports are provided on the discharge, liquid and suction line. Evacuated, dehydrated and charge with refrigerant gas prior to shipment.
CASING
Constructed from heavy gauge galvanized steel. Panels are painted with epoxy powder paint for excellent finish, weatherability and corrosion resistance. Evaporator section is insulated with 1 x 1 1/2 lb per.cu.ft of linacoustic fiberglass.
EFFICIENT EVAPORATOR COIL
Independent thermal expansion valve with external equalizer for better refrigerant control and wider load condition.
Leak and pressure tested to 450 psig Evacuated, dehydrated and charged with refrigerant gas.
DRIVE PACKAGE AND BLOWERS
Belt driven drive package offers flexibility on various air flow rate and various static pressure applications (ACPSB Series 160P and above).
Single large diameter double inlet double width blowers (AMCA certified) reduce the noise level and eliminates the need for common transition and eliminates air unbalance.
FILTERS
1” thick with side loading for ACPSB Series 30P to 145P. 2” thick with side loading for ACPSB Series 160P and above.
OPTIONAL ACCESSORIES
Factory wired starters - DOL for compressors and fan motors. - Auto-transformer for compressors.
Suction stop valve(s), discharge stop valve(s) and liquid stop valve(s). Fan staging (ACPSB Series 160P and above) of multiple fans for head pressure control. Thermostat. Hydrophilic fins or copper fins for better corrosion resistance. Hot gas by pass for low load and low ambient conditions. Hot water heating coils. Electric heaters. Optional R22 refrigerant.
Product that perform…By people who care
- 4 -
COOLING & HEATING PORTFOLIO
Reference Hz Capacity
MBH kW
ACPRB 30 Cooling 50/60 29.3 8.6 Heating 50/60 31.6 9.3
ACPSB 40 Cooling 50/60 39.0 11.4 Heating 50/60 42.1 12.3
ACPSB 50 Cooling 50/60 48.8 14.3 Heating 50/60 52.7 15.4
ACPSB 68 Cooling 50/60 59.2 17.3 Heating 50/60 63.9 18.7
ACPSB 81 Cooling 50/60 71.2 20.9 Heating 50/60 76.9 22.5
ACPSB 95 Cooling 50/60 83.8 24.6 Heating 50/60 90.5 26.5
ACPSB 108 Cooling 50/60 97.6 28.6 Heating 50/60 105.4 30.9
ACPSB 125 Cooling 50/60 109.8 32.2 Heating 50/60 117.6 34.5
ACPSB 145 Cooling 50/60 127.2 37.3 Heating 50/60 137.4 40.3
ACPSB 160 Cooling 50/60 146.4 42.9 Heating 50/60 158.1 46.3
ACPSB 190 Cooling 50/60 165.9 48.6 Heating 50/60 179.2 52.5
ACPSB 220 Cooling 50/60 195.2 57.2 Heating 50/60 210.8 61.8
ACPSB 250 Cooling 50/60 219.6 64.4 Heating 50/60 237.2 69.5
ACPSB 290 Cooling 50/60 253.8 74.4 Heating 50/60 274.1 80.3
ACPSB 320 Cooling 50/60 292.8 85.8 Heating 50/60 316.2 92.7
ACPSB 380 Cooling 50/60 341.6 100.1 Heating 50/60 368.9 108.1
ACPSB 435 Cooling 50/60 380.6 111.5 Heating 50/60 411.0 120.5
ACPSB 480 Cooling 50/60 424.6 124.4 Heating 50/60 458.6 134.4
ACPSB 510 Cooling 50/60 449.0 131.6 Heating 50/60 484.9 142.1
ACPSB 570 Cooling 50/60 497.8 145.9 Heating 50/60 537.6 157.6
ACPSB 640 Cooling 50/60 566.1 165.9 Heating 50/60 611.4 179.2
ACPSB 700 Cooling 50/60 624.6 183.1 Heating 50/60 674.6 197.7
ACPSB 760 Cooling 50/60 673.4 197.4 Heating 50/60 727.3 213.1
ACPSB 800 Cooling 50/60 722.2 211.7 Heating 50/60 780.0 228.6
ACPSB 890 Cooling 50/60 790.6 231.7 Heating 50/60 853.8 250.2
ACPSB 960 Cooling 50/60 858.9 251.7 Heating 50/60 927.6 271.9
ACPSB 1020 Cooling 50/60 907.7 266.0 Heating 50/60 980.3 287.3
ACPSB 1140 Cooling 50/60 995.5 291.8 Heating 50/60 1075.1 315.1
ACPSB 1340 Cooling 50/60 1190.7 349.0 Heating 50/60 1286.0 376.9
ACPSB 1520 Cooling 50/60 1327.4 389.0 Heating 50/60 1433.6 420.1
Notes: 1.) Ratings Are Gross Capacities - For Net Capacities, Deduct Evaporator Blower Motor Heat. 2.) Cooling Mode: At 80 °F (DB), 67 °F (WB) Air on Evaporator And 95°F Ambient Air Temperature on Condenser. 3.) Heating Mode: At 70 °F (DB) Air on Evaporator And 45°F Ambient Air Temperature on Condenser.
Product that perform…By people who care
- 5 -
PHYSICAL SPECIFICATIONS 50 Hz
Notes: 1) Evaporator blower motor for 30P to 145P is 220/240-1-50Hz and direct drive. 2) Condenser fan motors voltage is 220/240-1-50Hz for model 30P to 50P. 3) ACPRB 30P is rotary compressor and the power supply is 220/240-1-50Hz. 4) Sound Pressure Level is calculated based on nominal airflow at external static pressure of 0.5" WG (Model 30-145) / 1.5 WG (Model 160-1520), 3m (9.8ft) distance
away from unit at free field. Unit supply and return are assumed to be entirely insulated. The actual sound at field could be affected by the supply and return duct break out noise.
5) Minimum-maximum voltage is 360V to 440V. 6) LRA - Locked Rotor Amp. 7) NRA - Nominal Running Amp. 8) MRA - Maximum Running Amp.
Model
Compressor Condenser Coil Cond. Fan
Motor HP
(Qty)
Evaporator Blower Evaporator Coil Air Filter Refrigerant
Charge Approx.
Operating Weight (Lbs)
Sound Pressure
Level±2 dB(A)Qty MRA
Each LRA Each
NRA Each
Face Area
ft²
Row / FPI Standard Size (Qty)
Motor Max HP
(Qty)
Fan Min-Max
Cfm
Face Area
ft² Row /
FPI Size Inches
(Qty)
Lbs Per System (Qty)
Cooling Only
Heat Pump
Cooling Only
Heat Pump
ACPRB 30P 1 - 1x62 1x12.6 4.6 2/16 3/12 1/5(1) DD9x7
(1) 0.6(1) 650 1280 2.1 3/12 16x25x1(1) 4.5(1) 7.2(1) 550 62
ACPSB 40P 1 - 1x45 1x6.8 7.2 2/16 3/12 1/5(1) DD9x7
(1) 0.6(1) 920 1800 3.1 3/12 20x25x1(1) 6.4(1) 9.1(1) 600 62
ACPSB 50P 1 - 1x56 1x8.2 8.3 2/14 3/12 1/5(1) DD9x9
(1) 0.6(1) 1100 2200 3.7 3/12 20x25x1(1) 7.2(1) 9.9(1) 650 62
ACPSB 68P 1 - 1x45 1x9.3 8.3 2/12 2/12 5/8(1) DD9x9
(1) 1(1) 1400 2800 4.7 3/12 16x25x1(2) 7.5(1) 10.2(1) 1100 66
ACPSB 81P 1 1x15.0 1x101 1x10.5 9.4 2/14 3/12 5/8(1) DD10x10
(1) 1(1) 1550 3100 5.2 3/12 16x25x1(1)
20x25x1(1) 9.9(1) 15.4(1) 1200 66
ACPSB 95P 1 1x15.6 1x95 1x12.5 10.9 2/16 3/12 5/8(1) DD10x10
(1) 1(1) 1550 3100 5.2 4/12 16x25x1(1)
20x25x1(1) 12.1(1) 17.6(1) 1300 66
ACPSB 108P 1 1x16.8 1x111 1x13.7 14.2 2/16 3/12 5/8(1) DD10x10
(2) 0.8(2) 1850 3600 6.1 4/12 20x25x1(2) 13.2(1) 18.7(1) 1500 66
ACPSB 125P 1 1x19.6 1x118 1x15.8 14.2 3/14 3/12 5/8(1) DD10x10
(2) 0.8(2) 2000 3900 6.6 4/12 20x25x1(2) 13.2(1) 18.7(1) 1600 67
ACPSB 145P 1 1x22.3 1x118 1x17.6 16.3 3/16 3/12 5/8(1) DD10x10
(2) 1(2) 2600 5100 8.5 4/12 20x25x1(2) 15.4(1) 20.9(1) 1750 67
ACPSB 160P 1 1x25.6 1x167 1x19.1 19.5 2/16 3/12 5/8(2) 15x15
(1) 5.5(1) 3500 7000 11.7 3/12 20x20x2(2)
20x25x2(2) 23.1(1) 28.7(1) 1700 69
ACPSB 190P 1 1x30.0 1x198 1x23.7 19.5 3/12 3/12 5/8(2) 15x15
(1) 5.5(1) 3500 7000 11.7 4/12 20x20x2(2)
20x25x2(2) 25.4(1) 30.9(1) 1800 70
ACPSB 220P 2 2x16.8 2x111 2x13.7 19.5 3/16 4/12 5/8(2) 15x15
(1) 5.5(1) 3700 7300 12.3 4/12 20x20x2(2)
20x25x2(2) 13.2(2) 18.7(2) 1900 69
ACPSB 250P 2 2x19.6 2x118 2x15.8 27.4 3/16 4/12 5/8(2) 18x13
(1) 7.5(1) 4400 8700 14.6 4/12 25x25x2(4) 13.2(2) 18.7(2) 2100 71
ACPSB 290P 2 2x22.3 2x118 2x17.6 27.4 4/16 5/12 5/8(2) 18x13
(1) 7.5(1) 5000 10000 16.7 4/12 25x25x2(4) 15.4(2) 20.9(2) 2400 71
ACPSB 320P 2 2x25.6 2x167 2x19.1 37.5 3/14 4/12 5/8(3) 18x18
(1) 15(1) 5850 11600 19.4 4/12 16x25x2(2)
20x25x2(4) 23.1(2) 28.7(2) 2900 71
ACPSB 380P 2 2x30.0 2x198 2x23.7 37.5 4/14 5/12 5/8(3) 18x18
(1) 15(1) 6700 13400 22.6 4/12 16x20x2(3)
20x20x2(6) 25.4(2) 30.9(2) 3000 72
ACPSB 435P 3 3x22.3 3x118 3x17.6 40 4/16 5/12 5/8(3) 450x450
(1) 20(1) 7000 14000 23.3 4/12 16x20x2(3)
20x20x2(6) 15.4(3) 20.9(3) 3100 72
ACPSB 480P 3 3x25.6 3x167 3x19.1 48.3 3/14 4/12 5/8(4) 500x500
(1) 20(1) 8900 17900 29.7 3/12
20x20x2(2)20x25x2(5) 25x25x2(2)
23.1(3) 28.7(3) 4000 73
ACPSB 510P 3 2x25.6
1x30.0 2x167 1x198
2x19.1 1x23.7 48.3 3/16 4/12 5/8(4) 500x500
(1) 20(1) 8900 17900 29.7 3/13
20x20x2(2) 20x25x2(5) 25x25x2(2)
23.1(2) 25.4(1)
28.7(2) 30.9(1) 4300 73
ACPSB 570P 3 3x30.0 3x198 3x23.7 48.3 4/14 5/12 5/8(4) 500x500
(1) 20(1) 8900 17900 29.7 4/10
20x20x2(2) 20x25x2(5) 25x25x2(2)
25.4(3) 30.9(3) 4400 74
ACPSB 640P 4 4x25.6 4x167 4x19.1 65.3 3/12 3/12 1.5(4) 560x560
(1) 30(1) 1000020000 33.4 4/10 20x20x2(4)
20x25x2(8) 23.1(4) 28.7(4) 6500 79
ACPSB 700P 4 2x25.6
2x30.0 2x167 2x198
2x19.1 2x23.7 65.3 3/14 4/12 1.5(4) 560x560
(1) 30(1) 10000 20000 33.4 4/12 20x20x2(4)
20x25x2(8) 23.1(2) 25.4(2)
28.7(2) 30.9(2) 6650 79
ACPSB 760P 4 4x30.0 4x198 4x23.7 65.3 4/12 4/12 1.5(4) 560x560
(1) 30(1) 10400 20800 34.7 4/12 20x20x2(4)
20x25x2(8) 25.4(4) 30.9(4) 6750 79
ACPSB 800P 5 5x25.6 5x167 5x19.1 94.0 3/16 4/12 1.5(4) 630x630
(1) 40(1) 13500 27000 45.1 4/10
20x20x2(4) 20x25x2(9) 25x25x2(2)
23.1(5) 28.7(5) 7000 79
ACPSB 890P 5 2x25.6
3x30.0 2x167 3x198
2x19.13x23.7 94.0 4/14 5/12 1.5(4) 630x630
(1) 40(1) 14000 28000 46.9 4/12
20x20x2(4) 20x25x2(9) 25x25x2(2)
25.4(3) 23.1(2)
30.9(3) 28.7(2) 7100 79
ACPSB 960P 6 6x25.6 6x167 6x19.1 94.0 4/16 5/12 1.5(4) 630x630
(1) 40(1) 14500 29000 48.6 4/12
20x20x2(4) 20x25x2(9) 25x25x2(2)
23.1(6) 28.7(6) 7250 79
ACPSB 1020P 6 4x25.6
2x30.0 4x167 2x198
4x19.1 2x23.7 123.0 3/16 4/12 1.5(4) 710x710
(1) 40(1) 16600 33300 55.6 4/10 20x20x2(12)
20x25x2(8) 23.1(4) 25.4(2)
28.7(4) 30.9(2) 8350 81
ACPSB 1140P 6 6x30.0 6x198 6x23.7 123.0 4/14 5/12 1.5(4) 710x710
(1) 40(1) 19000 38300 63.9 4/10 20x25x2(20) 25.4(6) 30.9(6) 9400 81
ACPSB 1340P 8 6x25.6
2x30.0 6x167 2x198
6x19.1 2x23.7 129.0 4/16 5/12 1.5(4) 800x800
(1) 50(1) 21600 43300 72.2 4/10 20x20x2(8)
20x25x2(18)23.1(6) 25.4(2)
28.7(6) 30.9(2) 10400 81
ACPSB 1520P 8 8x30.0 8x198 8x23.7 129.0 4/16 5/12 1.5(4) 800x800
(1) 50(1) 21600 43300 72.2 5/10 20x20x2(8)
20x25x2(16) 25.4(8) 30.9(8) 11000 82
Product that perform…By people who care
- 6 -
PHYSICAL SPECIFICATIONS 60 Hz
Model
Compressor Condenser Coil Cond. Fan
Motor HP
(Qty)
Evaporator Blower Evaporator Coil Air Filter Refrigerant
Charge Approx.
Operating Weight (Lbs)
Sound Pressure
Level±2 dB(A)Qty MRA
Each LRA Each
NRA Each
Face Area
ft²
Row / FPI Standard Size (Qty)
Motor MaxHP
Fan Min-Max
Cfm
Face Area
ft² Row/ FPI
Size Inches (Qty)
Lbs Per System (Qty)
Cooling Only
Heat Pump
Cooling Only
Heat Pump
6ACPRB 30P 1 - 1x82 1x12.5 4.6 2/16 3/12 1/5(1) DD9x7
(1) 0.6(1) 650 1280 2.1 3/12 16x25x1 (1) 3.5(1) 3.5(1) 550 62
6ACPRB 40P 1 - 1x62 1x16.4 7.2 2/16 3/12 1/5(1) DD9x7
(1) 0.6(1) 920 1800 3.1 3/12 20x25x1 (1) 3.7(1) 3.7(1) 600 62
6ACPSB 50P 1 - 1x45 1x6.8 8.3 2/14 3/12 1/5(1) DD9x9
(1) 0.6(1) 11002200 3.7 3/12 20x25x1 (1) 4.8(1) 4.8(1) 650 62
6ACPSB 68P 1 - 1x56 1x8.2 8.3 2/12 2/12 5/8(1) DD9x9
(1) 1(1) 14002800 4.7 3/12 16x25x1 (2) 5.9(1) 5.9(1) 1100 66
6ACPSB 81P 1 - 1x45 1x9.3 9.4 2/14 3/12 5/8(1) DD10x10
(1) 1(1) 15503100 5.2 3/12 16x25x1 (1)
20x25x1 (1) 8.3(1) 8.3(1) 1200 66
6ACPSB 95P 1 1x15.0 1x100 1x11.0 10.9 2/16 3/12 5/8(1) DD10x10
(1) 1(1) 15503100 5.2 4/12 16x25x1 (1)
20x25x1 (1) 9.9(1) 9.9(1) 1300 66
6ACPSB 108P 1 1x15.6 1x95.0 1x12.8 14.2 2/16 3/12 5/8(1) DD10x10
(2) 0.75(2) 18503600 6.1 4/12 20x25x1 (2) 12.3(1) 12.3(1) 1500 66
6ACPSB 125P 1 1x16.8 1x114 1x14.1 14.2 3/14 3/12 5/8(1) DD10x10
(2) 0.75(2) 20003900 6.6 4/12 20x25x1 (2) 13.2(1) 13.2(1) 1600 67
6ACPSB 145P 1 1x19.6 1x125 1x16.3 16.3 3/16 3/12 5/8(1) DD10x10
(2) 1(2) 26005100 8.5 4/12 20x25x1 (2) 17.6(1) 17.6(1) 1750 67
6ACPSB 160P 1 1x22.3 1x125 1x18.2 19.5 2/16 3/12 5/8(2) 15x15
(1) 5.5(1) 35007000 11.7 3/12 20x20x2 (2)
20x25x2 (2) 16.0(1) 16.0(1) 2100 69
6ACPSB 190P 1 1x25.6 1x158 1x19.1 19.5 3/12 3/12 5/8(2) 15x15
(1) 5.5(1) 35007000 11.7 4/12 20x20x2 (2)
20x25x2 (2) 23.8(1) 23.8(1) 2300 70
6ACPSB 220P 1 1x30.0 1x187 1x24.1 19.5 3/16 4/12 5/8(2) 15x15
(1) 5.5(1) 37007300 12.3 4/12 20x20x2 (2)
20x25x2 (2) 25.3(1) 25.3(1) 2600 69
6ACPSB 250P 2 2x16.8 2x114 2x14.1 27.4 3/16 4/12 5/8(2) 18x13
(1) 7.5(1) 44008700 14.6 4/12 25x25x2 (4) 13.2(2) 13.2(2) 2800 71
6ACPSB 290P 2 2x19.6 2x125 2x16.3 27.4 4/16 5/12 5/8(2) 18x13
(1) 7.5(1) 500010000 16.7 4/12 25x25x2 (4) 17.6(2) 17.6(2) 3000 71
6ACPSB 320P 2 2x22.3 2x125 2x18.2 37.5 3/14 4/12 5/8(3) 18x18
(1) 10(1) 585011600 19.4 4/12 16x25x2 (2)
20x25x2 (4) 16.0(2) 16.0(2) 4000 71
6ACPSB 380P 2 2x25.6 2x158 2x19.1 37.5 4/14 5/12 5/8(3) 18x18
(1) 10(1) 670013400 22.6 4/12 16x20x2 (3)
20x20x2 (6) 23.8(2) 23.8(2) 4400 72
6ACPSB 435P 2 2x30.0 2x187 2x24.1 40.0 4/16 5/12 5/8(3) 450x450
(1) 20(1) 700014000 23.3 4/12 16x20x2 (3)
20x20x2 (6) 25.3(2) 25.3(2) 4700 72
6ACPSB 480P 3 3x22.3 3x125 3x18.2 48.3 3/14 4/12 5/8(4) 500x500
(1) 20(1) 890017900 29.7 3/12
20x20x2 (2) 20x25x2 (5) 25x25x2 (2)
16.0(3) 16.0(3) 5500 73
6ACPSB 510P 3 3x25.6 3x158 3x19.1 48.3 3/16 4/12 5/8(4) 500x500
(1) 20(1) 890017900 29.7 3/13
20x20x2 (2) 20x25x2 (5) 25x25x2 (2)
23.8(3) 23.8(3) 5700 73
6ACPSB 570P 3 2x25.6
1x30.0 2x158 1x187
2x19.1 1x24.1 48.3 4/14 5/12 5/8(4) 500x500
(1) 20(1) 890017900 29.7 4/10
20x20x2 (2) 20x25x2 (5) 25x25x2 (2)
23.8(2) 25.3(1)
23.8(2) 25.3(1) 5950 74
6ACPSB 640P 3 3x30.0 3x187 3x24.1 65.3 3/12 3/12 1.5(4) 560x560
(1) 30(1) 1000020000 33.4 4/10 20x20x2 (4)
20x25x2 (8) 25.3(3) 25.3(3) 6500 79
6ACPSB 700P 4 4x25.6 4x158 4x19.1 65.3 3/14 4/12 1.5(4) 560x560
(1) 30(1) 1000020000 33.4 4/12 20x20x2 (4)
20x25x2 (8) 23.8(4) 23.8(4) 6650 79
6ACPSB 760P 4 2x25.6
2x30.0 2x158 2x187
2x19.1 2x24.1 65.3 4/12 4/13 1.5(4) 560x560
(1) 30(1) 1040020800 34.7 4/12 20x20x2 (4)
20x25x2 (8) 23.8(2) 25.3(2)
23.8(2) 25.3(2) 6750 79
6ACPSB 800P 4 4x30.0 4x187 4x24.1 94.0 3/16 4/12 1.5(4) 630x630
(1) 40(1) 1350027000 45.1 4/10
20x20x2 (4) 20x25x2 (9) 25x25x2 (2)
25.3(4) 25.3(4) 7000 79
6ACPSB 890P 5 5x25.6 5x158 5x19.1 94.0 4/14 5/12 1.5(4) 630x630
(1) 40(1) 1400028000 46.9 4/12
20x20x2 (4) 20x25x2 (9) 25x25x2 (2)
23.8(5) 23.8(5) 7100 79
6ACPSB 960P 6 6x22.3 6x125 6x18.2 94.0 4/16 5/12 1.5(4) 630x630
(1) 40(1) 1450029000 48.6 4/12
20x20x2 (4) 20x25x2 (9) 25x25x2 (2)
16.0(6) 16.0(6) 7250 79
6ACPSB 1020P 6 2x25.6
4x22.3 2x158 4x125
2x19.1 4x18.2 123.0 3/16 4/12 1.5(4) 710x710
(1) 40(1) 1660033300 55.6 4/10 20x20x2 (12)
20x25x2 (8) 16.0(4) 23.8(2)
16.0(4) 23.8(2) 8350 81
6ACPSB 1140P 6 4x25.6
2x30.0 4x158 2x187
4x19.1 2x24.1 123.0 4/14 5/12 1.5(4) 710x710
(1) 40(1) 1900038300 63.9 4/10 20x25x2 (20) 23.8(4)
25.3(2) 23.8(4) 25.3(2) 9400 81
6ACPSB 1340P 6 6x30.0 6x187 6x24.1 129.0 4/16 5/12 1.5(4) 800x800
(1) 50(1) 2160043300 72.2 4/10 20x20x2 (8)
20x25x2 (16) 25.3(6) 25.3(6) 10400 81
6ACPSB 1520P 8 6x25.6
2x30.0 6x158 2x187
6x19.1 2x24.1 129.0 4/16 5/12 1.5(4) 800x800
(1) 50(1) 2160043300 72.2 5/10 20x20x2 (8)
20x25x2 (16) 23.8(6) 25.3(2)
23.8(6) 25.3(2) 11000 82
Notes: 1) Evaporator Blower motor for 6ACPRB 30P to 145P is 220/240-1-60Hz and direct drive. 2) Condenser fan motors voltage is 220/240-1-60Hz for model 30P to 50P. 3) 6ACPRB 30P & 6ACPRB 40P is rotary compressor and the power supply is 230-1-60Hz. 4) Sound Pressure Level is calculated based on nominal airflow at external static pressure of 0.5" WG (Model 30-145) / 1.5 WG (Model 160-1520), 3m (9.8ft) distance
away from unit at free field. Unit supply and return are assumed to be entirely insulated. The actual sound at field could be affected by the supply and return duct break out noise.
5) LRA - Locked Rotor Amp. 6) NRA - Nominal Running Amp. 7) MRA - Maximum Running Amp.
Product that perform…By people who care
- 7 -
SYSTEM COOLING CAPACITY PERFORMANCE DATA – COOLING ONLY
Model Std.
Capacity MBH [kW]
Air On Evap. Cooling Capacity @ Air Temperature On Condenser Coil
CFM [m³/h]
WB Temp 75⁰F [24⁰C] 95⁰F [35⁰C] 115⁰F [46⁰C]
Total Sensible KW Input³
Total Sensible KW Input³
Total Sensible KW Input³ ⁰F ⁰C MBH¹ kW¹ MBH² kW² MBH¹ kW¹ MBH² kW² MBH¹ kW¹ MBH² kW²
ACPRB 30PP 29.3 [8.6] 1,000
[1,699]
72 22.2 34.1 10.0 15.9 4.7 2.4 32.3 9.5 15.4 4.5 2.8 30.2 8.9 14.8 4.3 3.1
67 19.4 31.6 9.3 20.2 5.9 2.3 29.3 8.6 19.3 5.7 2.7 28.0 8.2 19.0 5.6 3.0
62 16.7 29.1 8.5 24.4 7.2 2.2 27.5 8.1 23.8 7.0 2.5 25.7 7.5 23.1 6.8 2.8
ACPSB 40PP
39.0 [11.4]
1,400 [2,379]
72 22.2 45.5 13.3 22.0 6.4 3.1 43.1 12.6 21.3 6.2 3.6 40.4 11.8 20.4 6.0 4.0
67 19.4 42.1 12.3 27.9 8.2 3.0 39.0 11.4 26.6 7.8 3.4 37.3 10.9 26.2 7.7 3.8
62 16.7 38.8 11.4 33.7 9.9 2.9 36.7 10.8 32.8 9.6 3.3 34.3 10.1 31.9 9.3 3.6
ACPSB 50PP
48.8 [14.3]
1,600 [2,718]
72 22.2 56.9 16.7 28.0 8.2 3.9 53.9 15.8 27.1 7.9 4.4 50.4 14.8 25.9 7.6 5.0
67 19.4 52.7 15.4 35.5 10.4 3.7 48.8 14.3 34.0 10.0 4.3 46.7 13.7 33.3 9.8 4.7
62 16.7 48.5 14.2 42.9 12.6 3.6 45.9 13.5 41.8 12.3 4.1 42.9 12.6 40.6 11.9 4.5
ACPSB 68PP
59.2 [17.3]
2,000 [3,398]
72 22.2 66.6 19.5 36.3 10.6 4.2 62.9 18.4 34.5 10.1 4.5 59.2 17.3 31.3 9.2 4.7
67 19.4 63.6 18.6 48.8 14.3 4.1 59.2 17.3 45.5 13.3 4.4 56.1 16.4 43.2 12.7 4.6
62 16.7 57.9 17.0 57.9 17.0 3.9 54.3 15.9 54.3 15.9 4.3 51.1 15.0 51.1 15.0 4.5
ACPSB 81PP
71.2 [20.9]
2,400 [4,078]
72 22.2 79.9 23.4 43.6 12.8 5.1 75.3 22.1 41.3 12.1 5.5 71.0 20.8 37.4 11.0 5.8
67 19.4 76.2 22.3 58.4 17.1 5.0 71.2 20.9 54.6 16.0 5.4 67.1 19.7 51.7 15.2 5.7
62 16.7 69.5 20.4 63.3 18.6 4.8 65.0 19.0 59.3 17.4 5.3 61.2 17.9 55.9 16.4 5.5
ACPSB 95PP
83.8 [24.6]
2,600 [4,417]
72 22.2 94.4 27.7 52.1 15.3 5.9 88.8 26.0 49.1 14.4 6.3 83.8 24.6 46.3 13.6 6.6
67 19.4 90.1 26.4 69.4 20.3 5.7 83.8 24.6 64.7 19.0 6.2 79.4 23.3 61.4 18.0 6.5
62 16.7 82.2 24.1 82.2 24.1 5.7 76.9 22.5 76.9 22.5 6.1 72.4 21.2 72.4 21.2 6.4
ACPSB 108PP
97.6 [28.6]
3,200 [5,437]
72 22.2 109.8 32.2 60.6 17.8 6.9 103.5 30.3 57.1 16.7 7.3 97.5 28.6 53.9 15.8 7.7
67 19.4 104.8 30.7 80.7 23.7 6.7 97.6 28.6 75.3 22.1 7.2 92.4 27.1 71.4 20.9 7.6
62 16.7 95.6 28.0 95.6 28.0 6.6 89.5 26.2 89.5 26.2 7.1 84.2 24.7 84.2 24.7 7.5
ACPSB 125PP
109.8 [32.2]
3,500 [5,947]
72 22.2 122.6 35.9 68.0 19.9 7.5 116.4 34.1 64.0 18.8 8.0 108.8 31.9 60.3 17.7 8.4
67 19.4 117.0 34.3 90.0 26.4 7.3 109.8 32.2 83.9 24.6 8.0 103.2 30.2 79.4 23.3 8.4
62 16.7 106.7 31.3 106.7 31.3 7.2 100.6 29.5 100.6 29.5 7.8 94.1 27.6 94.1 27.6 8.2
ACPSB 145PP
127.2 [37.3]
4,000 [6,796]
72 22.2 142.1 41.6 70.5 20.7 8.5 130.0 38.1 66.3 19.4 9.1 126.1 37.0 62.5 18.3 9.6
67 19.4 135.6 39.7 93.3 27.3 8.3 127.2 37.3 87.0 25.5 9.1 119.4 35.0 82.2 24.1 9.6
62 16.7 123.6 36.2 112.0 32.8 8.2 116.5 34.1 104.8 30.7 8.9 109.0 31.9 98.9 29.0 9.3
ACPSB 160PP
146.4 [42.9]
4,600 [7,815]
72 22.2 165.1 48.4 97.4 28.5 10.4 155.5 45.6 91.8 26.9 11.1 146.4 42.9 86.4 25.3 11.6
67 19.4 157.5 46.2 132.4 38.8 9.9 146.4 42.9 119.3 35.0 11.0 138.8 40.7 117.0 34.3 11.5
62 16.7 143.8 42.1 143.8 42.1 9.8 134.5 39.4 134.5 39.4 10.8 126.7 37.1 126.7 37.1 11.2
ACPSB 190PP
165.9 [48.6]
4,800 [8,155]
72 22.2 187.0 54.8 93.1 27.3 11.8 176.0 51.6 96.8 28.4 12.6 165.8 48.6 91.4 26.8 13.2
67 19.4 178.4 52.3 136.1 39.9 11.5 165.9 48.6 126.8 37.2 12.4 157.3 46.1 120.2 35.2 13.0
62 16.7 162.7 47.7 162.7 47.7 11.3 152.2 44.6 152.2 44.6 12.2 143.5 42.1 143.5 42.1 12.8
ACPSB 220PP
195.2 [57.2]
5,400 [9,175]
72 22.2 221.0 64.8 132.7 38.9 13.7 208.0 61.0 125.2 36.7 14.5 195.0 57.1 117.2 34.3 15.4
67 19.4 207.2 60.7 177.7 52.1 13.6 195.2 57.2 167.5 49.1 14.4 183.1 53.7 157.2 46.1 15.4
62 16.7 191.5 56.1 191.5 56.1 13.4 181.3 53.1 181.3 53.1 14.3 169.4 49.6 169.4 49.6 15.3
ACPSB 250PP
219.6 [64.4]
6,400 [10,874]
72 22.2 245.2 71.9 133.8 39.2 15.3 230.9 67.7 126.1 37.0 16.3 217.6 63.8 118.9 34.8 17.0
67 19.4 234.0 68.6 176.2 51.6 14.8 219.6 64.4 165.8 48.6 16.2 206.3 60.5 157.3 46.1 16.9
62 16.7 213.5 62.6 208.6 61.1 14.6 199.7 58.5 199.7 58.5 15.8 188.2 55.2 188.2 55.2 16.6
ACPSB 290PP
253.8 [74.4]
7,500 [12,743]
72 22.2 283.3 83.0 147.1 43.1 17.8 266.5 78.1 138.4 40.6 18.9 250.0 73.3 130.1 38.1 20.1
67 19.4 265.6 77.8 189.2 55.4 17.7 253.8 74.4 178.4 52.3 18.7 234.9 68.8 167.5 49.1 20.0
62 16.7 245.1 71.8 228.4 66.9 17.4 232.5 68.1 216.6 63.5 18.7 217.1 63.6 202.3 59.3 19.9
ACPSB 320PP
292.8 [85.8]
8,000 [13,592]
72 22.2 331.6 97.2 171.0 50.1 20.7 312.1 91.5 161.2 47.2 22.0 292.5 85.7 151.3 44.3 23.3
67 19.4 310.9 91.1 218.6 64.1 20.6 292.8 85.8 206.0 60.4 21.8 274.8 80.5 193.6 56.7 23.2
62 16.7 287.2 84.2 262.3 76.9 20.2 272.0 79.7 239.7 70.2 21.6 245.1 71.8 232.7 68.2 23.1
Notes: 1) Ratings are based on 80oF [27oC] air on evaporator dry bulb temperature. 2) Ratings are gross capacities. For net capacity deduct evaporator blower motor heat. 3) kW input shown in the table is total compressor(s) power input. 4) R22 performance data can be estimated from the above data by applying below factor: +1% on cooling capacity, -3% on compressor kW input.
Product that perform…By people who care
- 8 -
SYSTEM COOLING CAPACITY PERFORMANCE DATA – COOLING ONLY
Model Std.
Capacity MBH [kW]
Air On Evap. Cooling Capacity @ Air Temperature On Condenser Coil
CFM [m³/h]
WB Temp 75⁰F [24⁰C] 95⁰F [35⁰C] 115⁰F [46⁰C]
Total Sensible KW Input³
Total Sensible KW Input³
Total Sensible KW Input³ ⁰F ⁰C MBH¹ kW¹ MBH² kW² MBH¹ kW¹ MBH² kW² MBH¹ kW¹ MBH² kW²
ACPSB 380PP
341.6 [100.1]
9,200 [15,631]
72 22.2 384.4 112.7 206.2 60.4 24.2 361.8 106.0 194.3 56.9 25.6 341.0 99.9 183.3 53.7 27.2
67 19.4 366.6 107.4 272.6 79.9 24.0 341.6 100.1 254.1 74.5 25.5 323.1 94.7 240.9 70.6 27.1
62 16.7 334.3 98.0 330.5 96.9 23.6 313.0 91.7 309.7 90.8 25.3 294.9 86.4 292.2 85.6 26.9
ACPSB 435PP
380.6 [111.5]
11,500 [19,539]
72 22.2 426.8 125.1 208.0 61.0 27.5 403.5 118.3 197.7 57.9 29.2 380.3 111.5 179.5 52.6 31.1
67 19.4 407.7 119.5 279.1 81.8 27.3 380.6 111.5 260.9 76.5 29.2 361.2 105.9 247.8 72.6 30.9
62 16.7 373.4 109.4 337.2 98.8 26.8 350.2 102.6 313.7 91.9 28.8 327.0 95.8 298.0 87.3 30.8
ACPSB 480PP
424.6 [124.4]
12,000 [20,388]
72 22.2 479.9 140.6 249.5 73.1 29.9 451.5 132.3 235.0 68.9 31.8 423.2 124.0 220.4 64.6 33.8
67 19.4 449.7 131.8 375.1 109.9 29.7 424.6 124.4 302.0 88.5 31.6 397.7 116.6 283.8 83.2 33.6
62 16.7 415.6 121.8 378.7 111.0 29.2 393.7 115.4 359.1 105.2 31.4 367.7 107.8 335.7 98.4 33.4
ACPSB 510PP
449.0 [131.6]
14,000 [23,786]
72 22.2 508.6 149.1 262.8 77.0 31.9 478.5 140.2 247.6 72.6 33.9 448.6 131.5 232.3 68.1 36.0
67 19.4 476.8 139.7 334.7 98.1 31.7 449.0 131.6 315.7 92.5 33.6 421.4 123.5 296.5 86.9 35.9
62 16.7 440.4 129.1 401.2 117.6 31.2 417.3 122.3 380.6 111.5 33.3 389.7 114.2 355.7 104.2 35.6
ACPSB 570PP
497.8 [145.9]
15,000 [25,485]
72 22.2 563.8 165.2 294.7 86.4 35.3 530.6 155.5 275.8 80.8 37.4 497.3 145.7 258.7 75.8 39.8
67 19.4 528.7 154.9 439.6 128.8 35.0 497.8 145.9 354.0 103.7 37.2 467.2 136.9 332.6 97.5 39.6
62 16.7 488.3 143.1 444.9 130.4 34.4 462.7 135.6 422.0 123.7 36.9 432.0 126.6 394.4 115.6 39.3
ACPSB 640PP
566.1 [165.9]
16,000 [27,184]
72 22.2 641.3 187.9 329.8 96.7 39.9 603.4 176.8 310.7 91.1 42.3 565.6 165.8 291.7 85.5 45.0
67 19.4 601.1 176.2 418.5 122.6 39.6 566.1 165.9 394.5 115.6 42.0 531.4 155.7 370.6 108.6 44.7
62 16.7 555.3 162.7 506.0 148.3 39.0 526.2 154.2 479.9 140.6 41.7 491.5 144.0 448.7 131.5 44.5
ACPSB 700PP
624.6 [183.1]
17,200 [29,223]
72 22.2 707.3 207.3 365.4 107.1 44.2 665.5 195.0 344.1 100.8 46.9 623.8 182.8 324.5 95.1 49.8
67 19.4 663.1 194.3 465.6 136.5 43.9 624.6 183.1 439.1 128.7 46.5 585.8 171.7 412.5 120.9 49.6
62 16.7 612.5 179.5 558.0 163.5 43.2 580.3 170.1 529.2 155.1 46.3 542.1 158.9 494.9 145.0 49.2
ACPSB 760PP
673.4 [197.4]
18,000 [30,582]
72 22.2 763.1 223.6 394.3 115.6 47.7 718.1 210.5 371.3 108.8 50.7 673.1 197.3 350.2 102.6 53.9
67 19.4 715.6 209.7 502.4 147.2 47.4 673.4 197.4 473.9 138.9 50.4 632.1 185.2 445.1 130.4 53.7
62 16.7 660.9 193.7 602.2 176.5 46.6 626.3 183.5 571.1 167.4 49.9 584.9 171.4 534.0 156.5 53.3
ACPSB 800PP
722.2 [211.7]
19,600 [33,300]
72 22.2 818.3 239.8 422.7 123.9 51.0 770.1 225.7 398.1 116.7 54.1 721.8 211.5 375.5 110.0 57.5
67 19.4 767.2 224.8 538.7 157.9 50.7 722.2 211.7 508.0 148.9 53.7 677.8 198.6 477.3 139.9 57.2
62 16.7 708.7 207.7 645.7 189.2 49.7 671.5 196.8 612.4 179.5 53.3 627.2 183.8 572.6 167.8 56.8
ACPSB 890PP
790.6 [231.7]
21,000 [35,679]
72 22.2 886.0 259.7 461.1 135.1 55.5 833.9 244.4 434.0 127.2 58.9 781.7 229.1 407.4 119.4 62.6
67 19.4 830.6 243.4 566.7 166.1 55.2 790.6 231.7 558.1 163.6 58.5 734.3 215.2 524.3 153.7 62.3
62 16.7 767.4 224.9 699.2 204.9 54.3 727.1 213.1 663.1 194.3 58.1 679.0 199.0 619.9 181.7 61.9
ACPSB 960PP
858.9 [251.7]
23,000 [39,077]
72 22.2 972.9 285.1 506.3 148.4 60.5 915.6 268.3 476.6 139.7 64.2 858.3 251.5 447.3 131.1 68.2
67 19.4 912.1 267.3 622.2 182.3 60.1 858.9 251.7 612.9 179.6 63.8 806.2 236.3 575.7 168.7 68.0
62 16.7 842.7 247.0 767.8 225.0 59.2 798.5 234.0 728.2 213.4 63.3 745.6 218.5 680.6 199.5 67.5
ACPSB 1020PP
907.7 [266.0]
25,800 [43834]
72 22.2 1025.6 300.6 533.6 156.4 64.1 965.2 282.9 502.4 147.2 68.0 904.8 265.2 471.5 138.2 72.3
67 19.4 961.5 281.8 656.0 192.3 63.6 907.7 266.0 646.1 189.4 67.5 849.9 249.1 606.8 177.8 72.0
62 16.7 888.3 260.3 809.3 237.2 62.6 841.7 246.7 767.7 225.0 67.0 785.9 230.3 717.5 210.3 71.5
ACPSB 1140PP
995.5 [291.8]
26,400 [44,854]
72 22.2 1127.3 330.4 586.6 171.9 70.6 1060.8 310.9 552.2 161.8 74.9 994.4 291.4 518.3 151.9 79.5
67 19.4 1056.8 309.7 720.9 211.3 70.0 995.5 291.8 710.0 208.1 74.4 934.1 273.8 667.0 195.5 79.2
62 16.7 976.3 286.1 889.5 260.7 68.9 925.1 271.1 843.6 247.2 73.8 863.9 253.2 788.6 231.1 78.6
ACPSB 1340PP
1190.7 [249.0]
32,000 [54,368]
72 22.2 1331.5 390.2 692.8 203.0 84.0 1253.0 367.2 652.3 191.2 89.2 1174.6 344.2 612.1 179.4 94.8
67 19.4 1248.2 365.8 851.5 249.5 83.4 1190.7 349.0 838.8 245.8 88.6 1103.3 323.3 787.8 230.9 94.4
62 16.7 1153.2 338.0 1050.6 307.9 82.1 1092.6 320.2 996.5 292.0 87.9 1020.3 299.0 931.5 273.0 93.7
ACPSB 1520PP
1327.4 [1327.4]
36,000 [61,164]
72 22.2 1506.0 441.4 783.7 229.7 94.1 1417.3 415.4 737.8 216.2 99.8 1328.6 389.4 692.4 202.9 106.0
67 19.4 1412.0 413.8 963.2 282.3 93.4 1327.4 389.0 948.7 278.0 99.2 1248.0 365.8 891.2 261.2 105.6
62 16.7 1304.4 382.3 1188.4 348.3 92.0 1235.9 362.2 1127.2 330.3 98.4 1154.1 338.2 1053.6 308.8 104.8
Notes: 1) Ratings are based on 80oF [27oC] air on evaporator dry bulb temperature. 2) Ratings are gross capacities. For net capacity deduct evaporator blower motor heat. 3) kW input shown in the table is total compressor(s) power input. 4) R22 performance data can be estimated from the above data by applying below factor: +1% on cooling capacity, -3% on compressor kW input.
Product that perform…By people who care
- 9 -
SYSTEM HEATING CAPACITY PERFORMANCE DATA – HEAT PUMP HEATING MODE
Model Std.
Heating Capacity
MBH [kW]
Air Volume CFM
[m³/h]
Dry Bulb Temp
Heating Capacity @ Air Temperature On Condenser Coil
35⁰F [1.7⁰C] 45⁰F [7.2⁰C] 55⁰F [12.8⁰C]
Capacity KW Input²
Capacity KW Input²
Capacity KW Input² ⁰F ⁰C MBH¹ kW¹ MBH¹ kW¹ MBH¹ kW¹
ACPRB 30P-HPP
31.6 [9.3]
1,000 [1,699]
60 15.6 27.8 8.1 2.1 32.3 9.5 2.2 35.8 10.5 2.2
70 21.1 27.2 8.0 2.2 31.6 9.3 2.4 35.1 10.3 2.4
80 26.7 26.7 7.8 2.4 31.0 9.1 2.6 34.4 10.1 2.8
ACPSB 40P-HPP
42.1 [12.3]
1,400 [2,379]
60 15.6 36.9 10.8 2.6 43.0 12.6 2.8 47.6 14.0 2.8
70 21.1 36.2 10.6 2.8 42.1 12.3 3.1 46.7 13.7 3.0
80 26.7 35.5 10.4 3.0 41.3 12.1 3.3 45.8 13.4 3.8
ACPSB 50P-HPP
52.7 [15.4]
1,600 [2,718]
60 15.6 46.2 13.5 3.3 53.8 15.8 3.6 59.6 17.5 3.9
70 21.1 45.3 13.3 3.6 52.7 15.4 3.9 58.4 17.1 3.8
80 26.7 44.4 13.0 3.9 51.6 15.1 4.2 57.3 16.8 4.5
ACPSB 68P-HPP
63.9 [18.7]
2,000 [3,398]
60 15.6 56.1 16.4 3.4 65.2 19.1 3.7 72.3 21.2 3.9
70 21.1 55.0 16.1 3.7 63.9 18.7 4.0 70.9 20.8 3.9
80 26.7 53.9 15.8 3.9 62.7 18.4 4.3 69.5 20.4 4.6
ACPSB 81P-HPP
76.9 [22.5]
2,400 [4,078]
60 15.6 67.4 19.8 4.1 78.4 23.0 4.5 87.0 25.5 4.8
70 21.1 66.1 19.4 4.5 76.9 22.5 4.9 85.3 25.0 4.8
80 26.7 64.8 19.0 4.8 75.4 22.1 5.2 83.6 24.5 5.7
ACPSB 95P-HPP
90.5 [26.5]
2,600 [4,417]
60 15.6 79.4 23.3 4.1 107.5 31.5 5.2 102.4 30.0 5.6
70 21.1 77.8 22.8 4.5 90.5 26.5 5.6 100.4 29.4 5.5
80 26.7 76.3 22.4 4.8 88.7 26.0 6.0 98.4 28.8 6.5
ACPSB 108P-HPP
105.4 [30.9]
3,200 [5,437]
60 15.6 92.4 27.1 5.5 107.5 31.5 6.0 119.2 34.9 6.4
70 21.1 90.7 26.6 6.0 105.4 30.9 6.5 116.9 34.3 6.4
80 26.7 88.9 26.1 6.4 103.3 30.3 7.0 114.6 33.6 7.5
ACPSB 125P-HPP
117.6 [34.5]
3,500 [5,947]
60 15.6 103.1 30.2 6.1 120.0 35.2 6.6 133.0 39.0 7.2
70 21.1 101.1 29.6 6.6 117.6 34.5 7.2 130.4 38.2 7.1
80 26.7 99.1 29.0 7.2 115.3 33.8 7.7 127.8 37.5 8.4
ACPSB 145P-HPP
137.4 [40.3]
4,000 [6,796]
60 15.6 120.5 35.3 6.9 140.1 41.1 7.6 155.4 45.5 8.1
70 21.1 118.1 34.6 7.6 137.4 40.3 8.2 152.3 44.6 8.0
80 26.7 115.8 33.9 8.1 134.6 39.4 8.8 149.3 43.8 9.5
ACPSB 160P-HPP
158.1 [46.3]
4,600 [7,815]
60 15.6 138.7 40.6 8.4 161.3 47.3 9.1 178.8 52.4 9.9
70 21.1 136.0 39.9 9.1 158.1 46.3 9.9 175.3 51.4 9.7
80 26.7 133.3 39.1 9.9 154.9 45.4 10.6 171.9 50.4 11.5
ACPSB 190P-HPP
179.2 [52.5]
4,800 [8,155]
60 15.6 157.1 46.0 9.5 182.8 53.6 10.3 202.6 59.4 11.1
70 21.1 154.1 45.2 10.3 179.2 52.5 11.2 198.7 58.2 10.9
80 26.7 151.0 44.3 11.1 175.6 51.5 12.0 194.8 57.1 13.0
ACPSB 220P-HPP
210.8 [61.8]
5,400 [9,175]
60 15.6 184.9 54.2 11.0 215.0 63.0 12.0 238.4 69.9 12.9
70 21.1 181.3 53.1 12.0 210.8 61.8 13.0 233.8 68.5 12.7
80 26.7 177.7 52.1 12.9 206.6 60.5 13.9 229.2 67.2 15.1
ACPSB 250P-HPP
237.2 [69.5]
6,400 [10,874]
60 15.6 208.0 61.0 12.4 241.9 70.9 13.5 268.2 78.6 14.5
70 21.1 204.0 59.8 13.5 237.2 69.5 14.6 263.0 77.1 14.3
80 26.7 199.9 58.6 14.5 232.4 68.1 15.7 257.8 75.6 17.0
ACPSB 290P-HPP
274.1 [80.3]
7,500 [12,743]
60 15.6 240.4 70.5 14.3 279.6 81.9 15.5 310.0 90.9 16.7
70 21.1 235.7 69.1 15.5 274.1 80.3 16.8 304.0 89.1 16.5
80 26.7 231.1 67.7 16.7 268.6 78.7 18.1 298.0 87.3 19.6
ACPSB 320P-HPP
316.2 [92.7]
8,000 [13,592]
60 15.6 277.3 81.3 16.6 322.5 94.5 18.1 357.6 104.8 19.5
70 21.1 272.0 79.7 18.1 316.2 92.7 19.6 350.7 102.8 19.2
80 26.7 266.6 78.1 19.5 309.9 90.8 21.1 343.7 100.7 22.9
Notes: 1) Ratings are gross capacities. For net capacity add evaporator blower motor heat. 2) kW input shown in the table is total compressor(s) power input. 3) R22 performance data can be estimated from the above data by applying below factor: +1% on heating capacity, -3% on compressor kW input.
Product that perform…By people who care
- 10 -
SYSTEM HEATING CAPACITY PERFORMANCE DATA – HEAT PUMP HEATING MODE
Model Std.
Heating Capacity
MBH [kW]
Air Volume CFM
[m³/h]
Dry Bulb Temp
Heating Capacity @ Air Temperature On Condenser Coil
35⁰F [1.7⁰C] 45⁰F [7.2⁰C] 55⁰F [12.8⁰C]
Capacity KW Input²
Capacity KW Input²
Capacity KW Input² ⁰F ⁰C MBH¹ kW¹ MBH¹ kW¹ MBH¹ kW¹
ACPSB 380P-HPP
368.9 [108.1]
9,200 [15,631]
60 15.6 323.5 94.8 19.5 376.3 110.3 21.2 417.3 122.3 22.8
70 21.1 317.3 93.0 21.2 368.9 108.1 23.0 409.1 119.9 22.5
80 26.7 311.0 91.1 22.8 361.5 105.9 24.7 401.0 117.5 26.7
ACPSB 435P-HPP
411.0 [120.5]
11,500 [19,539]
60 15.6 360.5 105.7 22.3 419.3 122.9 24.3 464.9 136.2 26.2
70 21.1 353.5 103.6 24.3 411.0 120.5 26.3 455.9 133.6 25.8
80 26.7 346.5 101.5 26.2 402.8 118.0 28.3 446.8 130.9 30.6
ACPSB 480P-HPP
458.6 [134.4]
12,000 [20,388]
60 15.6 402.2 117.9 24.1 467.7 137.1 26.3 518.6 152.0 28.3
70 21.1 394.4 115.6 26.3 458.6 134.4 28.4 508.6 149.1 27.9
80 26.7 386.6 113.3 28.3 449.4 131.7 30.6 498.5 146.1 33.1
ACPSB 510P-HPP
484.9 [142.1]
14,000 [23,786]
60 15.6 425.3 124.6 25.6 494.6 145.0 27.9 548.4 160.7 30.1
70 21.1 417.0 122.2 27.9 484.9 142.1 30.2 537.8 157.6 29.6
80 26.7 408.8 119.8 30.1 475.2 139.3 32.5 527.1 154.5 35.2
ACPSB 570P-HPP
537.6 [157.6]
15,000 [25,485]
60 15.6 471.5 138.2 28.4 548.4 160.7 30.9 608.1 178.2 33.3
70 21.1 462.4 135.5 30.9 537.6 157.6 33.5 596.2 174.7 32.8
80 26.7 453.2 132.8 33.3 526.9 154.4 36.0 584.4 171.3 39.0
ACPSB 640P-HPP
611.4 [179.2]
16,000 [27,184]
60 15.6 536.2 157.1 32.1 623.6 182.8 34.9 691.5 202.7 37.6
70 21.1 525.8 154.1 34.9 611.4 179.2 37.8 678.0 198.7 37.0
80 26.7 515.4 151.0 37.6 599.2 175.6 40.6 664.6 194.8 44.0
ACPSB 700P-HPP
674.6 [197.7]
17,200 [29,223]
60 15.6 591.6 173.4 35.5 688.1 201.7 38.6 762.9 223.6 41.6
70 21.1 580.1 170.0 38.6 674.6 197.7 41.9 748.1 219.2 41.0
80 26.7 568.7 166.7 41.6 661.1 193.7 45.0 733.3 214.9 48.8
ACPSB 760P-HPP
727.3 [213.1]
18,000 [30,582]
60 15.6 637.8 186.9 38.5 741.8 217.4 41.9 822.5 241.1 45.1
70 21.1 625.5 183.3 41.9 727.3 213.1 45.4 806.5 236.4 44.5
80 26.7 613.1 179.7 45.1 712.7 208.9 48.8 790.5 231.7 52.8
ACPSB 800P-HPP
780.0 [228.6]
19,600 [33,300]
60 15.6 684.0 200.5 41.0 795.6 233.2 44.6 882.2 258.5 48.1
70 21.1 670.8 196.6 44.6 780.0 228.6 48.3 865.0 253.5 47.4
80 26.7 657.5 192.7 48.1 764.4 224.0 52.0 847.8 248.5 56.3
ACPSB 890P-HPP
853.8 [250.2]
21,000 [35,679]
60 15.6 748.8 219.5 44.6 870.9 255.2 48.6 965.7 283.0 52.4
70 21.1 734.3 215.2 48.6 853.8 250.2 52.7 946.9 277.5 51.6
80 26.7 719.8 211.0 52.4 836.8 245.2 56.6 928.1 272.0 61.3
ACPSB 960P-HPP
927.6 [271.9]
23,000 [39,077]
60 15.6 813.5 238.4 48.7 946.2 277.3 53.0 1049.1 307.5 57.1
70 21.1 797.7 233.8 53.0 927.6 271.9 57.4 1028.7 301.5 56.3
80 26.7 782.0 229.2 57.1 909.1 266.4 61.7 1008.3 295.5 66.9
ACPSB 1020P-HPP
980.3 [287.3]
25,800 [43834]
60 15.6 859.7 252.0 51.5 999.9 293.0 56.1 1108.7 324.9 60.4
70 21.1 843.1 247.1 56.1 980.3 287.3 60.8 1087.2 318.6 59.5
80 26.7 826.4 242.2 60.4 960.7 281.6 65.3 1065.6 312.3 70.8
ACPSB 1140P-HPP
1075.1 [315.1]
26,400 [44,854]
60 15.6 942.9 276.3 56.8 1096.6 321.4 61.8 1216.0 356.4 66.6
70 21.1 924.6 271.0 61.8 1075.1 315.1 67.0 1192.3 349.4 65.6
80 26.7 906.3 265.6 66.6 1053.6 308.8 72.0 1168.7 342.5 78.0
ACPSB 1340P-HPP
1286.0 [376.9]
32,000 [54,368]
60 15.6 1127.8 330.5 67.6 1311.7 384.4 73.6 1454.4 426.2 79.3
70 21.1 1106.0 324.1 73.6 1286.0 376.9 79.7 1426.2 418.0 78.1
80 26.7 1084.0 317.7 79.3 1260.2 369.3 85.7 1397.7 409.6 92.9
ACPSB 1520P-HPP
1433.6 [420.1]
36,000 [61,164]
60 15.6 1257.3 368.5 75.7 1462.3 428.6 82.4 1621.4 475.2 88.9
70 21.1 1232.9 361.3 82.4 1433.6 420.1 89.3 1589.9 466.0 87.5
80 26.7 1208.4 354.1 88.9 1404.9 411.7 96.0 1558.2 456.7 104.0
Notes: 1) Ratings are gross capacities. For net capacity add evaporator blower motor heat. 2) kW input shown in the table is total compressor(s) power input. 3) R22 performance data can be estimated from the above data by applying below factor: +1% on heating capacity, -3% on compressor kW input.
Product that perform…By people who care
- 11 -
BLOWER PERFORMANCE A.) ACPRB 30P & ACPSB 40P to 145P ( Direct Drive )
ACPRB 30P ACPSB 40P ACPSB 50P ACPSB 68P ACPSB 81P DD 9-7 DD 9-7 DD 9 - 9 DD 9 - 9 DD 10 - 10
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
CFM m³/h in WG Pa CFM m³/h in WG Pa CFM m³/h in WG Pa CFM m³/h in WG Pa CFM m³/h in WG Pa900 1529 1.11 276.5 1300 2209 0.88 219.2 1400 2379 0.88 219.2 1900 3228 0.82 204.3 2400 4078 0.96 239.1
1000 1699 1.04 259.1 1400 2379 0.73 181.8 1500 2549 0.77 191.8 2000 3398 0.68 169.4 2500 4248 0.75 186.8 1100 1869 0.95 236.6 1500 2549 0.5 124.5 1600 2718 0.63 156.9 2100 3568 0.58 144.5 2600 4417 0.56 139.5 1200 2039 0.82 204.3 1600 2718 0.18 44.8 1700 2888 0.4 99.6 2200 3738 0.47 117.1 2700 4587 0.3 74.7
ACPSB 95P ACPSB 108P ACPSB 125P ACPSB 145P DD 10 - 10 2 x (DD 10 - 10) 2 x (DD 10 - 10) 2 x (DD 10 - 10)
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
Airflow on Evaporator
External Static Pressure
CFM m³/h in WG Pa CFM m³/h in WG Pa CFM m³/h in WG Pa CFM m³/h in WG Pa2400 4078 0.87 216.7 3000 5097 1.06 264.0 3400 5777 0.84 209.2 3900 6626 1.27 316.3 2500 4248 0.64 159.4 3100 5267 1.01 251.6 3500 5947 0.77 191.8 4000 6796 1.22 303.9 2600 4417 0.46 114.6 3200 5437 0.99 246.6 3600 6116 0.71 176.9 4100 6966 1.17 291.4 2700 4587 0.19 47.3 3300 5607 0.94 234.1 3700 6286 0.65 161.9 4200 7136 1.14 284.0
B.) ACPSB 160P to 1520P ( Belt Driven )
RPM
CFM
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP FAN
MODEL in WG Pa in WG Pa in WG Pa in WG Pa in WG Pa
ACPSB 160P 4000 4400 4600 4800 5000
15-15 650 0.4 97.1 1.1 0.3 79.7 1.3 0.3 69.7 1.3 0.2 57.3 1.4 0.2 1.5 381.1 750 0.7 179.3 1.4 0.7 169.4 1.6 0.6 159.4 1.7 0.6 149.5 1.8 0.6 1.9 465.8 850 1.1 266.5 1.7 1.0 259.1 1.9 1.0 254.1 2.0 1.0 249.1 2.1 1.0 2.3 565.4 950 1.4 358.7 2.0 1.4 356.2 2.3 1.4 353.7 2.4 1.4 348.7 2.6 1.4 2.7 672.5
ACPSB 190P 4000 4400 4800 5000 5200
15-15 700 0.5 119.6 1.2 0.4 102.1 1.4 0.3 77.2 1.6 0.3 67.3 1.7 0.2 52.3 1.4 800 0.8 204.3 1.5 0.8 191.8 1.7 0.7 174.4 2.0 0.7 166.9 2.1 0.6 154.4 2.2 900 1.2 293.9 1.9 1.1 284.0 2.1 1.1 274.0 2.3 1.1 266.5 2.5 1.0 259.1 2.6
1000 1.6 388.6 2.3 1.5 383.6 2.5 1.5 376.1 2.8 1.5 373.6 3.0 1.5 366.2 3.1 ACPSB 220P
4600 5000 5400 5800 6200
15-15 800 0.8 189.3 1.8 0.7 174.4 2.1 0.6 149.5 2.3 0.5 119.6 2.6 0.4 87.2 2.9 900 1.2 286.5 2.2 1.1 274.0 2.5 1.0 256.6 2.8 0.9 234.1 3.1 0.8 206.7 3.4
1000 1.6 386.1 2.6 1.5 381.1 3.0 1.5 368.7 3.3 1.4 351.2 3.6 1.3 328.8 4.0 1100 2.0 493.2 3.1 2.0 493.2 3.5 2.0 485.7 3.8 1.9 470.8 4.2 1.8 455.8 4.6
ACPSB 250P 5600 6000 6400 6800 7200
18-13 600 0.4 107.1 2.0 0.3 84.7 2.2 0.2 57.3 2.5 - - - - - - 700 0.9 231.7 2.5 0.9 211.7 2.8 0.8 191.8 3.1 0.7 166.9 3.4 0.6 137.0 3.7 800 1.5 361.2 3.1 1.4 348.7 3.4 1.3 331.3 3.8 1.3 313.9 4.1 1.2 293.9 4.0 900 2.0 500.7 3.8 2.0 490.7 4.1 1.9 480.7 4.5 1.9 465.8 4.7 1.8 448.4 5.3
ACPSB 290P 6500 7000 7500 8000 8500
18-13 700 0.8 204.3 3.1 0.7 174.4 3.6 0.6 137.0 3.9 0.4 92.2 4.3 0.2 42.3 4.8 800 1.4 348.7 3.8 1.3 323.8 4.3 1.2 293.9 4.7 1.0 259.1 5.3 0.9 216.7 5.8 900 2.0 495.7 4.6 1.9 480.7 5.1 1.8 458.3 5.7 1.7 428.4 6.2 1.6 396.1 6.8
1000 2.6 655.1 5.5 2.7 660.1 6.1 2.5 627.7 6.7 2.4 605.3 7.3 2.3 580.4 8.0 ACPSB 320P
7200 7600 8000 8400 8800
18-18 700 0.9 214.2 3.2 0.8 199.3 3.5 0.7 184.3 3.7 0.7 166.9 4.0 0.6 147.0 4.3 800 1.4 341.3 4.0 1.3 331.3 4.3 1.3 318.8 4.6 1.2 303.9 4.9 1.2 288.9 5.3 900 1.9 478.3 4.8 1.9 470.8 5.2 1.9 460.8 5.5 1.8 450.9 5.9 1.8 438.4 6.3
1000 2.5 622.7 5.8 2.5 617.7 6.2 2.5 610.3 6.6 2.4 602.8 7.0 2.4 595.3 7.5 ACPSB 380P
7600 8400 9200 10000 10800
18-18 600 0.9 219.2 3.5 0.8 189.3 4.0 0.6 151.9 4.6 0.4 102.1 5.3 0.2 52.3 6.0 700 1.4 351.2 4.3 1.3 326.3 4.9 1.2 296.4 5.6 1.0 256.6 6.4 0.9 211.7 7.2 800 2.0 488.2 5.2 1.9 473.3 5.9 1.8 448.4 6.7 1.7 416.0 7.6 1.5 378.6 8.6 900 2.6 637.7 6.2 2.5 627.7 7.1 2.5 610.3 8.0 2.3 582.9 9.0 2.2 553.0 10.0
ACPSB 435P 9200 10400 11500 12400 13200
450x450 (mm)
700 0.7 179.3 4.5 0.5 117.1 5.4 0.2 39.9 6.3 - - - - - - 800 1.3 313.9 5.5 1.1 269.0 6.6 0.8 209.2 7.6 0.6 147.0 8.6 0.3 82.2 9.5 900 1.8 453.3 6.8 1.7 423.5 7.9 1.5 378.6 9.1 1.3 328.8 10.2 1.1 276.5 11.2
1000 2.4 592.8 8.2 2.3 577.9 9.5 2.2 545.5 10.8 2.1 513.1 12.0 1.9 468.3 13.1 ACPSB 480P
10400 11200 12000 12800 13600
500x500 (mm)
600 0.7 161.9 4.2 0.5 134.5 4.7 0.4 102.1 5.2 0.3 64.8 5.7 0.1 22.4 6.3 700 1.2 301.4 5.4 1.1 281.5 5.9 1.0 256.6 6.5 0.9 226.7 7.2 0.8 191.8 7.9 800 1.8 443.4 6.7 1.7 433.4 7.4 1.7 416.0 8.1 1.6 396.1 8.8 1.5 371.1 9.6 900 2.4 597.8 8.3 2.4 590.3 9.1 2.3 582.9 9.9 2.3 570.4 10.7 2.2 550.5 11.6
Product that perform…By people who care
- 12 -
BLOWER PERFORMANCE
RPM
CFM
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP
Static Pressure BHP FAN
MODEL in WG Pa in WG Pa in WG Pa in WG Pa in WG Pa
ACPSB 510P 12400 13200 14000 14800 15600
500x500 (mm)
600 0.3 77.2 5.5 0.1 34.9 6.0 - - - - - - - - - 700 1.0 236.6 6.8 0.8 204.3 7.5 0.7 166.9 8.2 0.5 122.1 9.0 0.3 69.7 9.8 800 1.6 398.5 8.4 1.5 373.6 9.2 1.4 346.2 10.0 1.3 311.4 10.9 1.1 269.0 11.8 900 2.3 570.4 10.3 2.2 553.0 11.2 2.1 530.6 12.1 2.0 503.2 13.1 1.9 470.8 14.1
ACPSB 570P 12000 13000 14000 15000 16000
500x500 (mm)
600 0.4 94.7 5.2 0.2 44.8 5.9 - - - - - - - - - 700 1.0 249.1 6.5 0.8 209.2 7.3 0.7 161.9 8.2 0.4 107.1 9.2 0.2 47.3 10.2 800 1.6 408.5 8.1 1.5 376.1 9.0 1.4 341.3 10.0 1.2 296.4 11.1 1.0 246.6 12.3 850 2.0 490.7 8.9 1.9 465.8 10.0 1.8 435.9 11.0 1.6 396.1 12.2 1.4 348.7 13.4
ACPSB 640P 14000 15000 16000 17000 18000
560x560 (mm)
600 0.9 216.7 6.8 0.8 186.8 7.5 0.6 149.5 8.2 0.5 112.1 9.0 0.3 64.8 9.9 650 1.2 298.9 7.7 1.1 276.5 8.5 1.0 244.1 9.3 0.8 206.7 10.1 0.7 164.4 11.1 700 1.5 383.6 8.8 1.5 366.2 9.6 1.4 338.8 10.5 1.2 308.9 11.4 1.1 266.5 12.3 750 1.9 470.8 9.9 1.8 458.3 10.8 1.7 433.4 11.7 1.7 411.0 12.8 1.5 376.1 13.8
ACPSB 700P 15200 16200 17200 18200 19200
560x560 (mm)
650 1.0 244.1 8.7 0.8 209.2 9.5 0.7 169.4 10.4 0.5 122.1 11.3 0.3 72.2 12.2 700 1.3 333.8 9.8 1.2 303.9 10.7 1.1 269.0 11.6 0.9 226.7 12.6 0.7 184.3 13.7 750 1.7 425.9 11.0 1.6 401.0 11.9 1.5 371.1 13.0 1.3 331.3 14.0 1.2 293.9 15.1 800 2.1 520.6 12.3 2.0 500.7 13.3 1.9 475.8 14.4 1.8 443.4 15.6 1.6 403.5 16.7
ACPSB 760P 16000 17000 18000 19000 20000
560x560 (mm)
650 0.9 226.7 9.3 0.8 186.8 10.2 0.6 144.5 11.1 0.4 97.1 12.1 0.2 37.4 13.0 700 1.3 321.3 10.5 1.2 286.5 11.4 1.0 244.1 12.3 0.8 204.3 13.4 0.6 151.9 14.5 750 1.7 416.0 11.7 1.6 388.6 12.8 1.4 353.7 13.8 1.3 313.9 14.9 1.1 269.0 16.1 800 2.1 510.6 13.1 2.0 490.7 14.2 1.9 460.8 15.3 1.7 423.5 16.5 1.5 381.1 17.7
ACPSB 800P 16600 18100 19600 21100 22600
630x630 (mm)
600 1.6 391.1 10.1 1.5 378.6 11.3 1.5 361.2 12.6 1.4 336.3 14.0 1.2 303.9 15.5 650 1.9 483.2 11.6 1.9 473.3 12.9 1.9 460.8 14.3 1.8 443.4 15.9 1.7 416.0 17.5 700 2.3 577.9 13.2 2.3 572.9 14.6 2.3 562.9 16.2 2.2 550.5 17.9 2.1 528.1 19.6 750 2.7 677.5 15.0 2.7 680.0 16.6 2.7 670.0 18.2 2.7 662.6 20.1 2.6 647.6 22.0
ACPSB 890P 19000 20500 22000 23500 25000
630x630 (mm)
600 1.4 351.2 12.0 1.3 326.3 13.4 1.2 293.9 14.6 1.0 256.6 16.4 0.9 211.7 18.1 650 1.8 450.9 13.7 1.8 435.9 15.3 1.6 408.5 16.9 1.5 376.1 18.5 1.3 333.8 20.3 700 2.2 555.5 15.6 2.2 540.5 17.2 2.1 520.6 19.0 2.0 495.7 20.8 1.8 458.3 22.7 750 2.7 662.6 17.6 2.6 647.6 19.3 2.5 630.2 21.2 2.5 615.2 23.2 2.4 587.8 25.3
ACPSB 960P 20000 21500 23000 24500 26000
630x630 (mm)
600 1.4 343.7 13.0 1.3 313.9 14.4 1.1 279.0 15.9 0.9 234.1 17.5 0.7 184.3 19.2 650 1.8 445.9 14.7 1.7 423.5 16.3 1.6 398.5 18.0 1.4 358.7 19.7 1.3 316.3 21.6 700 2.2 553.0 16.7 2.2 538.0 18.4 2.1 510.6 20.1 1.9 480.7 22.1 1.8 445.9 24.1 750 2.7 660.1 18.7 2.6 650.1 20.6 2.5 632.7 22.6 2.4 605.3 24.6 2.3 575.4 26.8
ACPSB 1020P 22800 24300 25800 27300 28800
710x710 (mm)
550 1.6 388.6 14.6 1.5 371.1 15.8 1.4 348.7 17.2 1.3 321.3 18.6 1.2 288.9 20.1 600 2.0 503.2 17.0 2.0 490.7 18.4 1.9 468.3 19.8 1.8 448.4 21.4 1.7 418.5 23.0 650 2.5 622.7 19.6 2.5 612.8 21.2 2.4 595.3 22.8 2.3 577.9 24.4 2.2 555.5 26.3 700 3.0 747.3 22.5 3.0 737.3 24.1 2.9 724.8 25.9 2.9 714.9 27.8 2.8 695.0 29.7
ACPSB 1140P 23200 24800 26400 28000 29600
710x710 (mm)
500 1.2 293.9 12.7 1.1 269.0 14.0 1.0 239.1 15.3 0.8 209.2 16.8 0.7 171.9 18.3 550 1.6 406.0 14.9 1.5 383.6 16.3 1.4 358.7 17.7 1.3 333.8 19.4 1.2 301.4 21.0 600 2.1 518.1 17.3 2.0 503.2 18.8 1.9 483.2 20.4 1.9 463.3 2.2 1.7 433.4 24.0 650 2.6 642.6 20.1 2.5 627.7 21.7 2.5 612.8 23.4 2.4 592.8 25.3 2.3 570.4 27.2
ACPSB 1340P 28000 30000 32000 34000 36000
800x800 (mm)
450 1 324 16 1 306 17 1 284 19 1 254 21 1 222 23 500 2 453 19 2 436 21 2 416 23 2 394 25 1 366 27 550 2 585 22 2 575 24 2 558 26 2 538 29 2 513 31 600 3 725 26 3 715 28 3 705 31 3 692 33 3 670 36
ACPSB 1520P 33000 34500 36000 37500 39000
800x800 (mm)
450 1.0 239.1 20.1 0.9 216.7 21.6 0.8 191.8 23.0 0.7 164.4 24.6 0.5 134.5 26.2 500 1.5 373.6 23.6 1.4 353.7 25.2 1.3 331.3 26.8 1.2 308.9 28.5 1.1 279.0 30.3 550 2.1 515.6 27.4 3.0 747.3 29.2 1.9 480.7 31.0 1.9 460.8 32.9 1.8 435.9 34.9 600 2.7 665.1 31.7 2.6 652.6 33.7 2.6 637.7 35.7 2.5 620.2 37.8 2.4 597.8 39.9
Product that perform…By people who care
- 13 -
DIMENSIONAL DATA ACPRB 30P, ACPSB 40P
MODEL A B
ACPRB 30P 32 [813] 16 [406] ACPSB 40P 40 [1016] 20[508]
ACPSB 50P
ACPSB 68P
Note: All Dimensions Are In Inches [mm].
Product that perform…By people who care
- 14 -
DIMENSIONAL DATA ACPSB 81P, 95P
ACPSB 108P, 125P
ACPSB 145P
Note: All Dimensions Are In Inches [mm].
Product that perform…By people who care
- 15 -
DIMENSIONAL DATA ACPSB 160P, 190P, 220P
MODEL A
STANDARD RUBBER ACPSB 160P 13 1/2 [343] 16 1/2 [419] ACPSB 190P 13 1/2 [343] 16 1/2 [419]
ACPSB 220P 13 1/2 [343] 16 1/2 [419]
ACPSB 250P, 290P
MODEL A STANDARD RUBBER
ACPSB 250P 15 3/4 [400] 18 3/4 [476] ACPSB 290P 15 3/4 [400] 18 3/4 [476]
ACPSB 320P, 380P, 435P
MODEL A B C STANDARD RUBBER
ACPSB 320P ]674[ 4/3 81 ]154[4/3 71 ]384[ 91 ]955[ 22ACPSB 380P ]674[ 4/3 81 ]154[4/3 71 ]384[ 91 ]955[ 22ACPSB 435P ]754[ 81 ]234[ 71 ]275[ 2/1 22 ]275[ 2/1 22
Note: All Dimensions Are In Inches [mm].
Product that perform…By people who care
- 16 -
DIMENSIONAL DATA ACPSB 480P, 510P, 570P
MODEL A
STANDARD RUBBER ACPSB 480P 18 [457] 19 [483] ACPSB 510P 18 [457] 19 [483]
ACPSB 570P 18 [457] 19 [483]
ACPSB 640P, 700P, 760P
ACPSB 800P, 890P, 960P
Note: All Dimensions Are In Inches [Mm].
Product that perform…By people who care
- 17 -
DIMENSIONAL DATA ACPSB 1020P
ACPSB 1140P
ACPSB 1340P, 1520P
Note: All Dimensions Are In Inches [Mm].
Product that perform…By people who care
- 18 -
TYPICAL WIRING SCHEMATIC With IEC Direct-On-Line (DOL) Option
GUIDE SPECIFICATIONS
1 General Air cooled packaged unit shall include compressor(s), evaporator and condenser coils with fans, refrigeration piping, electrical components and enclosing cabinet in one piece. The units shall be factory assembled, internally wired, fully refrigerant charged with R22 or R407C and are suitable for outdoor installation on ground level with ducted system. The units shall be capable to operate up to 115°F [46°C] ambient temperature without failure.
2 Cabinet The unit cabinet shall be constructed from heavy gauge galvanized steel with epoxy painted for excellent finished, weatherability and corrosion resistance up to 1000 hours salt spray test according to ASTM B-117. Evaporator section shall be of 13mm [1/2 inch] (model ACPSB Series 30P to 145P) and 25mm [1 inch] (model ACPSB Series 160P and above) thick single skin and lined with minimum 2lbs/ft3 [32kg/m3] density having thermal conductivity of 0.0346W/m.K [0.24 Btu.in/ft2.h.oF] acoustical fiberglass insulation. The insulation shall have fire resistant of Class O (BS 476 Part 6, 7). Access doors shall be provided for easy service and maintenance of unit internal parts.
3 Compressor & Refrigeration Piping Compressor(s) shall be scroll, refrigerant gas cooled and mounted on the base via vibration isolators. 1, 2, 3 or 4 refrigeration circuits shall be piped with copper tubing and include expansion valve with external equalizer, filter dryer, sight glass, pressure fittings of manual reset high pressure control and auto reset low
pressure safety cutouts as well as charging/access ports in each circuit. The compressors comply with the internationally recognized standards CE and UL.
4 Evaporator Coil Evaporator coil shall be of draw through air design for uniform air distribution. The evaporator coil shall be quality construction of staggered row of 3/8”OD (model ACPSB Series 30 to 570P) and 1/2”OD (model ACPSB Series 640P and above) seamless copper tube, mechanically bonded to aluminium fins with galvanized coil plates. The coil shall be factory leak and pressure tested to 450psig [31bar] under water. A galvanized and painted drain pan shall be provided to cover the entire coil area. The drain pan shall be designed to incorporate sloped gutter for complete condensate removal.
5 Evaporator Blower and Motor Evaporator blower shall be direct-driven (model ACPSB Series 30 to 145P) and belt driven (model ACPSB Series 160P and above), double-inlet-double-width (DIDW) forward curved. All blowers are statically and dynamically balanced to ensure quiet operation and smooth performance. Heavy-duty V-belt fan drive with cast iron pulleys keyed and secured to the blower shaft shall be provided (model ACPSB Series 160P and above). Motors shall be of totally enclosed fan cooled (TEFC) with IP55 enclosure rating, 4-poles with class F insulation. Motors shall be mounted to an adjustable motor frame. Motor pulleys shall be cast iron, keyed and secured to the motor shaft (model ACPSB Series 160P and above).
Product that perform…By people who care
- 19 -
GUIDE SPECIFICATIONS 6 Condenser Coil Condenser coil shall be air cooled with integral sub-cooling circuit, constructed from staggered row of 3/8”OD inner grooved seamless copper tube, mechanically bonded to aluminium fins with galvanized coil plates. The coil shall be factory leak and pressure tested to 450psig [31 bar] under water.
7 Condenser Fan and Motor Condenser fan shall be direct driven propeller type discharging air vertically upward. Condenser fans shall be constructed of corrosion resistant blades and are statically and dynamically balanced. Condenser fan motors shall be of totally enclosed fan cooled (TEFC) with IP55 enclosure rating, 6-poles with class F insulation and wired to unit control panel (model ACPSB 68P and above). The condenser fan assembly shall be provided with heavy gauge and rust resistant steel wire fan guard.
8 Filters Units shall be provided with 1” (model ACPSB Series 30P to 145P) and 2” (model ACPSB Series 160P and above) thick washable pleated filters having average arrestance efficiency of 70% (model ACPSB Series 30P to 145P) and 75% (model ACPSB Series 160P and above) as per ASHRAE Standard 52.1 (or equivalent) with side loading.
9 Control Panel The unit mounted control panel enclosure shall be constructed from heavy gauge galvanized steel with epoxy painted for excellent finished, weatherability and corrosion resistance. The enclosure shall conform to IP54. Hinged and lock type access door shall be provided for easy access and security. The control panel shall be wired without starter and control.
10 Options
10.1 Hot Gas Bypass The refrigerant circuit (applicable to ‘first in last out’ refrigeration system only) shall be provided with a hot gas bypass system for low load and low ambient condition (evaporator freeze protection).
10.2 Evaporator Coil Fin Materials In lieu of standard aluminium fin, alternative fin material and/or protective coating include,
Hydrophilic coated aluminium fin Aluminium fin with Airestec coating
10.3 Condenser Coil Fin Materials In lieu of standard aluminium fin, alternative fin material and/or protective coating include,
Hydrophilic coated aluminium fin Aluminium fin with Airestec coating
10.4 Discharge / Suction / Liquid Line Service Valves Service valves shall be provided at each refrigerant lines for service convenience.
10.5 Closed Cell Elastomer Insulation 1/2 inch (model ACPSB 30P to 145P) and 1 inch (model ACPSB 160P and above) thick closed cell elastomer insulation (Insulflex®) shall be provided in lieu of standard fiberglass insulation. Closed cell elastomer insulation shall comply Class O (BS476 Part 6) and Class 1 (BS476 Part 7) fire resistant standard.
10.6 Carel Controller Panel mounted thermostat is provided for the unit to control and maintain the room temperature at a constant level or set point.
10.7 1” Double Wall Fiberglass Casing (Evaporator Section) 1” double wall fiberglass casing shall be provided in lieu of single skin fiberglass casing (model ACPSB 160P and above).
10.8 Hot Water Heating Coil Hot water coil shall be provided for heating purpose (hot water shall be field supplied).
10.9 Evaporator Blower Isolator Rubber or spring isolator shall be provided to dampen vibration caused by motor and blower (model ACPSB Series 160P and above).
10.10 IEC DOL (Non UL) The unit mounted control panel enclosure shall be constructed from heavy gauge galvanized steel with epoxy painted for excellent finished, weatherability and corrosion resistance. The enclosure shall conform to IP54. Hinged and lock type access door shall be provided for easy access and security. The control panel shall be factory wired and shall include compressor, evaporator fan motor and condenser fan motor circuit breaker and contactors, compressor and evaporator fan motor thermal overload relays, anti-recycling time delay relay, control circuit fuse, power and control circuit terminal blocks and features 230V controls with 380-415V/3PH/50HZ (+Neutral) power supply or 115V/230V/24V controls with 208V-230V/380/460V-3PH-60HZ power\supply.
10.11 Indicating Lights Indication provided for high-pressure trip and compressor run.
10.12 UVR/Phase Failure Protect. Phase Failure Relay is provided for over voltage, under voltage and phase loss protection
10.13 Low Ambient Kit Fan cycling for better performance during low ambient.
10.14 Door Interlock Main Incoming Isolator Incoming Isolator is provided for isolate the main incoming power supply to the unit.