A318/A319/A320/A321 31700 BLAGNAC CONF ALL ATA …

207
A318/A319/A320/A321 SERVICE BULLETIN REV 00 Jun 13/19 A320-25-1BPY Page 1 CONF ALL AIRBUS 2, ROND POINT EMILE DEWOITINE 31700 BLAGNAC FRANCE The content of this document is the property of Airbus. It is supplied in confidence and commercial security on its contents must be maintained. It must not be used for any purpose other than that for which it is supplied, nor may information contained in it be disclosed to unauthorized persons. It must not be reproduced in whole or in part without permission in writing from the owners of the copyright. Requests for reproduction of any data in this document and the media authorized for it must be addressed to Airbus. ATA SYSTEM: 25 TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS - REVISE BIN BASE FOR PIVOTING OHSC MODIFICATION No.: 162563K30846

Transcript of A318/A319/A320/A321 31700 BLAGNAC CONF ALL ATA …


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 1

CONF ALLAIRBUS2, ROND POINT EMILE DEWOITINE31700 BLAGNACFRANCE The content of this document is the property of Airbus.It is supplied in confidence and commercial security on its contents must be maintained.It must not be used for any purpose other than that for which it is supplied, nor may informationcontained in it be disclosed to unauthorized persons.It must not be reproduced in whole or in part without permission in writing from the owners of thecopyright. Requests for reproduction of any data in this document and the media authorized for it mustbe addressed to Airbus.

ATA SYSTEM: 25

TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS -REVISE BIN BASE FOR PIVOTING OHSC

MODIFICATION No.:162563K30846


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 2

ATA SYSTEM: 25

TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS -REVISE BIN BASE FOR PIVOTING OHSC

SUMMARYThis summary is for information only and is not approved for modification of the aircraft.A. MODIFICATIONS

CONF 001

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 002

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 003

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 004

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 005

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 3

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 006

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF 007

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

CONF ALLB. REASON

(1) HistorySeveral damages to the pivoting bins of the Overhead Stowage Compartments (OHSC)have been reported in-service leading to unscheduled and additional maintenance.

(2) Objective/ActionThis Service Bulletin is published to advise the operators of the affected MSNs toinstall new pivoting bins which provide a more robust bonding design.

(3) AdvantagesThe accomplishment of this Service Bulletin will improve the robustness and increasethe lifetime of the pivoting OHSCs leading to a reduction in unscheduled maintenance.

(4) Operational/Maintenance ConsequencesNone

C. GENERAL EVALUATION

EVALUATION TABLECOMPLIANCE RECOMMENDED COST SAVING NOA/C OPERATIONAFFECTED

NO VENDOR SB NO

CANCELS INSPECTION SB NO ETOPS AFFECTED NOPAX COMFORT AFFECTED YES POTENTIAL AD NORELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NOLIFE LIMIT NO LINE MAINTENANCE AFFECTED NO


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 4

NOTE: Service Bulletin recommended to be accomplished to prevent significantoperational disruptions.

D. MAINTENANCE CONFIGURATIONCONF 001

No specific aircraft maintenance configuration required.CONF 002

No specific aircraft maintenance configuration required.CONF 003

No specific aircraft maintenance configuration required.CONF 004

No specific aircraft maintenance configuration required.CONF 005

No specific aircraft maintenance configuration required.CONF 006

No specific aircraft maintenance configuration required.CONF 007

No specific aircraft maintenance configuration required.CONF ALL

E. MATERIAL PRICE INFORMATIONCONF 001

(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in the

Pivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD01R00 1 394500.00 USD Bin assembliesPart kit 251BPYD08R00 1 50.00 USD Washers and screwsTOTAL   394550.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 002(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD02R00 1 503000.00 USD Bin assembliesPart kit 251BPYD09R00 1 60.00 USD Washers and screwsTOTAL   503060.00 USD  


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 5

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 003(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD03R00 1 450000.00 USD Bin assembliesPart kit 251BPYD10R00 1 60.00 USD Washers and screwsTOTAL   450060.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 004(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD04R00 1 404000.00 USD Bin assembliesPart kit 251BPYD11R00 1 50.00 USD Washers and screwsTOTAL   404050.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 005(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD05R00 1 484000.00 USD Bin assembliesPart kit 251BPYD12R00 1 60.00 USD Washers and screws


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 6

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

TOTAL   484060.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 006(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD06R00 1 404000.00 USD Bin assembliesPart kit 251BPYD11R00 1 50.00 USD Washers and screwsTOTAL   404050.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF 007(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPYD07R00 1 532000.00 USD Bin assembliesPart kit 251BPYD13R00 1 60.00 USD Washers and screwsTOTAL   532060.00 USD  Components See SB See Note Bracket

NOTE: Price information to be obtained from the given supplier.

CONF ALLF. APPLICABILITY

This Service Bulletin is applicable to this (these) operator(s):ANZ HAL KZR LAN SKU TAM

G. CONCURRENT REQUIREMENTSAccomplishment of this Service Bulletin requires the prior or simultaneous accomplishmentof the following Service Bulletin:


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 7

Service Bulletin(s) Modification(s)Ref. SB A320-25-1BPZ  

NOTE: Ref. SB A320-25-1BPZ (EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGECOMPARTMENTS - REVISE INSTALLATION OF DAMPENER FOR POHSC BINS).

H. NATURE OF THE WORKCONF 001

(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in the

Pivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 002(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 003(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 004(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 005(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 006(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 8

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF 007(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT NOEQUIPMENT YES

CONF ALLI. MANPOWER

CONF 001(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 24.50 hELAPSED TIME (HOURS) 12.75 h

CONF 002(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 31.00 hELAPSED TIME (HOURS) 16.25 h

CONF 003(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 28.50 hELAPSED TIME (HOURS) 15.00 h

CONF 004(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 25.00 h


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

REV 00 Jun 13/19 A320-25-1BPYPage 9

MANPOWERELAPSED TIME (HOURS) 13.00 h

CONF 005(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 30.00 hELAPSED TIME (HOURS) 15.75 h

CONF 006(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 25.00 hELAPSED TIME (HOURS) 13.00 h

CONF 007(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

MANPOWERTOTAL MAN-HOURS 33.25 hELAPSED TIME (HOURS) 17.50 h


A318/A319/A320/A321SERVICE BULLETIN

SUMMARY

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJQ-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYGeneral overview

Page 10

CONF ALLJ. GENERAL OVERVIEW

CONF ALL

Z200

A

TYPICAL

OVERHEAD STOWAGE COMPARTMENTTO BE MODIFIED

A

ICN-A320-A-25XX1BPY-A-FAPE3-01CJQ-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 11

ATA SYSTEM: 25

TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS -REVISE BIN BASE FOR PIVOTING OHSC

1. PLANNING INFORMATIONA. APPLICABILITY

NOTE: An accomplishment Overhead Stowage Compartment (OHSC) per OHSC is allowed.

(1) ModelsON A/C 08444, 08497, 08521, 08523, 08691, 08693, 08731, 08999

320-251NON A/C 07844, 07864, 08140, 08166, 08172, 08529, 08715, 08803, 08833

320-271NON A/C 08495, 08596, 08635

320-273NON A/C 07917, 07959, 08092, 08123, 08129, 08157, 08186, 08237, 08266, 08471, 08578,08764, 08872

321-271NON A/C 08496, 08542, 08573, 08629, 08799, 08837, 08839, 08908

321-271NXCONF ALL

(2) Applicability by MSN07844 07864 07917 07959 08092 08123 08129 08140 08157 08166 08172 0818608237 08266 08444 08471 08495-08497 08521 08523 08529 08542 08573 0857808596 08629 08635 08691 08693 08715 08731 08764 08799 08803 08833 0883708839 08872 08908 08999

(3) MSN by configurationCONF 001

MSN CONFIGURATION08495 08529 08596 08635 001

CONF 002

MSN CONFIGURATION07917 07959 08092 08123 08129 08157 08186 08237 0826608471 08578 08764 08872

002

CONF 003

MSN CONFIGURATION08715 08803 08833 003

CONF 004

MSN CONFIGURATION08444 08497 08521 08523 08691 08693 08731 08999 004

CONF 005


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 12

MSN CONFIGURATION08837 005

CONF 006

MSN CONFIGURATION07844 07864 08140 08166 08172 006

CONF 007

MSN CONFIGURATION08496 08542 08573 08629 08799 08839 08908 007

CONF ALL(4) Configuration definition

CONF 001Configuration 001

CONF 001 is applicable for all LAN10 aircraft affected by this Service Bulletin.CONF 001 retrofits following modifications: 162563K30846.

CONF 002Configuration 002

CONF 002 is applicable for all HAL01 aircraft affected by this Service Bulletin.CONF 002 retrofits following modifications: 162563K30846.

CONF 003Configuration 003

CONF 003 is applicable for all ANZ05 aircraft affected by this Service Bulletin.CONF 003 retrofits following modifications: 162563K30846.

CONF 004Configuration 004

CONF 004 is applicable for all SKU01 aircraft affected by this Service Bulletin.CONF 004 retrofits following modifications: 162563K30846.

CONF 005Configuration 005

CONF 005 is applicable for all KZR07 aircraft affected by this Service Bulletin.CONF 005 retrofits following modifications: 162563K30846.

CONF 006Configuration 006

CONF 006 is applicable for all LAN11 aircraft affected by this Service Bulletin.CONF 006 retrofits following modifications: 162563K30846.

CONF 007Configuration 007

CONF 007 is applicable for all ANZ06 aircraft affected by this Service Bulletin.CONF 007 retrofits following modifications: 162563K30846.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 13

CONF ALLB. CONCURRENT REQUIREMENTS

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishmentof the following Service Bulletin:

Service Bulletin(s) Modification(s)Ref. SB A320-25-1BPZ  

NOTE: Ref. SB A320-25-1BPZ (EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGECOMPARTMENTS - REVISE INSTALLATION OF DAMPENER FOR POHSC BINS).

C. REASON

(1) HistorySeveral damages to the pivoting bins of the Overhead Stowage Compartments (OHSC)have been reported in-service leading to unscheduled and additional maintenance.

(2) Objective/ActionThis Service Bulletin is published to advise the operators of the affected MSNs toinstall new pivoting bins which provide a more robust bonding design.

(3) AdvantagesThe accomplishment of this Service Bulletin will improve the robustness and increasethe lifetime of the pivoting OHSCs leading to a reduction in unscheduled maintenance.

(4) Operational/Maintenance ConsequencesNone

D. DESCRIPTIONTo accomplish this Service Bulletin it is necessary to:(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

CONF 0011 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0021 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0031 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0041 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0051 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0061 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF 0071 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)

CONF ALL


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 14

2 Reidentify the Overhead Stowage Compartment AssembliesE. COMPLIANCE

(1) ClassificationRECOMMENDED: Service Bulletin recommended to be accomplished to preventsignificant operational disruptions.

(2) Accomplishment TimescaleAccomplishment of this Service Bulletin is recommended at the earliest opportunitywhere manpower and facilities are available.

F. APPROVALThe technical content of this document is approved under the authority of DesignOrganisation Approval No. EASA.21J.031.If an aircraft listed in the applicability has a modification or repair embodied that is notof AIRBUS origin, and which affects the content of this Service Bulletin, the operatoris responsible for obtaining approval by its airworthiness authority for any adaptationnecessary before incorporation of the Service Bulletin.

G. MANPOWERCONF 001

The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

20.50 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.00 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 24.50 hELAPSED TIME (HOURS) 12.75 h

CONF 002The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do not


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 15

include the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

26.50 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.50 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 31.00 hELAPSED TIME (HOURS) 16.25 h

CONF 003The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

24.00 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.50 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 28.50 h


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 16

ELAPSED TIME (HOURS) 15.00 h

CONF 004The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

21.00 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.00 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 25.00 hELAPSED TIME (HOURS) 13.00 h

CONF 005The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

25.50 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 17

TESTOperational Test 2.50 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 30.00 hELAPSED TIME (HOURS) 15.75 h

CONF 006The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDUREReplace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

21.00 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.00 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 25.00 hELAPSED TIME (HOURS) 13.00 h

CONF 007The manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATIONJob Set-up 0.25 h

PROCEDURE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 18

Replace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

28.50 h

Reidentify the Overhead Stowage CompartmentAssemblies

1.50 h

PREPARATION FOR TESTNone

TESTOperational Test 2.75 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 33.25 hELAPSED TIME (HOURS) 17.50 h

CONF ALLH. WEIGHT AND BALANCE

CONF 001 004 006The weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +31.1 kg (+68.563 lb)Effect on Balance +621.2 kg.m (+4493.140 lb.ft)

CONF 002The weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +40.0 kg (+88.184 lb)Effect on Balance +938.8 kg.m (+6790.340 lb.ft)

CONF 003The weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +30.1 kg (+66.358 lb)Effect on Balance +594.4 kg.m (+4299.295 lb.ft)

CONF 005The weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +38.9 kg (+85.759 lb)Effect on Balance +923.3 kg.m (+6678.229 lb.ft)

CONF 007The weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +40.1 kg (+88.404 lb)Effect on Balance +942.1 kg.m (+6814.209 lb.ft)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 19

CONF ALLI. ELECTRICAL LOAD DATA

Not changedJ. REFERENCES

CONCURRENT SERVICE BULLETIN (SB)A320-25-1BPZ

CONF 001(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 002(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 003(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 20

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 004(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 005(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 21

STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 006(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF 007(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

CONF ALLK. PUBLICATION AFFECTED

AIRCRAFT MAINTENANCE MANUAL (AMM)ILLUSTRATED PART CATALOG (IPC)

L. INDUSTRY SUPPORT INFORMATIONAIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kitsat no charge for orders placed before Apr 30/22.AIRBUS will credit the man-hours indicated in this Service Bulletin at the agreed in-housewarranty labor rate for claims received no later than 90 days after completion of the last


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 22

affected aircraft of your fleet, for the accomplishment of this Service Bulletin before Apr30/22.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 23

2. MATERIAL INFORMATIONA. MATERIAL APPLICABILITY

CONF 001Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD01R00 1Part kit 251BPYD08R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF 002Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD02R00 1Part kit 251BPYD09R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF 003Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD03R00 1Part kit 251BPYD10R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF 004Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD04R00 1Part kit 251BPYD11R00 1Components See SBInterchangeable parts See SB


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 24

MATERIAL QTY SEE NOTESSpare parts See SB

CONF 005Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD05R00 1Part kit 251BPYD12R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF 006Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD06R00 1Part kit 251BPYD11R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF 007Material for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPYD07R00 1Part kit 251BPYD13R00 1Components See SBInterchangeable parts See SBSpare parts See SB

CONF ALLB. TOOLING

No toolsC. CONSUMABLES

CONF 001Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 25

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 002Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 003Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 004Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 005Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 006Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF 007Consumables for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 26

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

CONF ALLD. LIST OF NEW PARTS

CONF 001Part kit 251BPYD01R00

Cost 394500.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 5 CMPRTMNTE2529795000100 3 CMPRTMNTE2529795000200 5 CMPRTMNTE2529795000300 3 CMPRTMNTE2529795000400 5 CMPRTMNTE2529795000500 6 CMPRTMNTE2529795000600 3 CMPRTMNTE2529795000700 5 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795001300 1 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 27

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795002500 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

CONF 002Part kit 251BPYD02R00

Cost 503000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 7 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 2 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795000800 1 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001700 1 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 28

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795001900 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 1 CMPRTMNTE2529797000000 1 CMPRTMNTE2529797000200 1 CMPRTMNTE2529797000400 2 CMPRTMNT

CONF 003Part kit 251BPYD03R00

Cost 450000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 8 CMPRTMNTE2529795000100 6 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 29

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 4 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 3 CMPRTMNTE2529795001300 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795002500 1 CMPRTMNTE2529795002700 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529795700600 1 CMPRTMNTE2529795700700 1 CMPRTMNTE2529796500200 1 CMPRTMNTE2529796500300 1 CMPRTMNT

CONF 004Part kit 251BPYD04R00

Cost 404000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 30

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 7 CMPRTMNTE2529795000100 6 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 3 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 2 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795002300 1 CMPRTMNTE2529795002500 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

CONF 005Part kit 251BPYD05R00

Cost 484000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 9 CMPRTMNTE2529795000100 6 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 31

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000200 7 CMPRTMNTE2529795000300 7 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795002100 1 CMPRTMNTE2529795002700 1 CMPRTMNTE2529795600200 1 CMPRTMNTE2529795600300 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 1 CMPRTMNT

CONF 006Part kit 251BPYD06R00

Cost 404000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 32

They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 5 CMPRTMNTE2529795000100 2 CMPRTMNTE2529795000200 5 CMPRTMNTE2529795000300 4 CMPRTMNTE2529795000400 5 CMPRTMNTE2529795000500 6 CMPRTMNTE2529795000600 4 CMPRTMNTE2529795000700 5 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

CONF 007Part kit 251BPYD07R00

Cost 532000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 33

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 7 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 8 CMPRTMNTE2529795000400 4 CMPRTMNTE2529795000500 4 CMPRTMNTE2529795000600 2 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001400 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600200 1 CMPRTMNTE2529795600300 1 CMPRTMNTE2529795700100 1 CMPRTMNTE2529795700300 1 CMPRTMNTE2529795700700 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796500300 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529797000000 1 CMPRTMNTE2529797000400 1 CMPRTMNT

CONF 001Part kit 251BPYD08R00

Cost 50.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 34

E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 164 SCREW3 NAS1149CN832R 164 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 002Part kit 251BPYD09R00

Cost 60.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 196 SCREW


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 35

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES3 NAS1149CN832R 196 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 003Part kit 251BPYD10R00

Cost 60.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 192 SCREW3 NAS1149CN832R 192 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 004 006Part kit 251BPYD11R00

Cost 50.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 36

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 168 SCREW3 NAS1149CN832R 168 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 005Part kit 251BPYD12R00

Cost 60.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 37

E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 204 SCREW3 NAS1149CN832R 204 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 007Part kit 251BPYD13R00

Cost 60.00 USDAvailability 162 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II BHein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 220 SCREW


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 38

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES3 NAS1149CN832R 220 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

CONF 001Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 41 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 002Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 39

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 49 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 003Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 48 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 004Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 40

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 42 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 005Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 51 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 006Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 41

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 42 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF 007Components for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

Procurement address D4296

AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 55 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

CONF ALLE. LIST OF EXISTING PARTS

CONF 001Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 42

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201100 E2529795001000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201300 E2529795001100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202500 E2529795002500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400600 E2529795600000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400700 E2529795600100 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 002Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 43

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200800 E2529795000800 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200900 E2529795000900 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201100 E2529795001000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201900 E2529795001700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202200 E2529795001900 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202400 E2529795002000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400600 E2529795600000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400700 E2529795600100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796000500 E2529796300100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100600 E2529796500000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100700 E2529796500100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200000 E2529796600000 01

COMPARTMENTASSY-OVHD STWG E2529796200100 E2529796600100 01

COMPARTMENTASSY-OVHD STWG E2529796200400 E2529796600200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200500 E2529796600300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529797200600 E2529797000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529797201000 E2529797000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529797202300 E2529797000200 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 44

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC is

allowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 003Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795100700 E2529795300100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202400 E2529795002000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202500 E2529795002500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202900 E2529795002700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400600 E2529795600000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400700 E2529795600100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795501000 E2529795700600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795501100 E2529795700700 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 45

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529796102000 E2529796500200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796102100 E2529796500300 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 004Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201100 E2529795001000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201300 E2529795001100 01

COMPARTMENTASSY-OVHD STWG E2529795202500 E2529795002500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202700 E2529795002300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400600 E2529795600000 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 46

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529795400700 E2529795600100 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 005Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202400 E2529795002000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202900 E2529795002700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795203100 E2529795002100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795402600 E2529795600200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795402700 E2529795600300 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 47

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529796000500 E2529796300100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100600 E2529796500000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100700 E2529796500100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200000 E2529796600000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200100 E2529796600100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200400 E2529796600200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200500 E2529796600300 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 006Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 48

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529795201100 E2529795001000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201300 E2529795001100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400600 E2529795600000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795400700 E2529795600100 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 007Interchangeable parts for task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795100700 E2529795300100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200000 E2529795000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200100 E2529795000100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200200 E2529795000200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200300 E2529795000300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200400 E2529795000400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200500 E2529795000500 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200600 E2529795000600 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200700 E2529795000700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795200900 E2529795000900 01 (1) (2)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 49

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529795201100 E2529795001000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201200 E2529795001300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795201500 E2529795001400 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795202400 E2529795002000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795402600 E2529795600200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795402700 E2529795600300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795500100 E2529795700100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795500900 E2529795700300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795501100 E2529795700700 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100600 E2529796500000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796100700 E2529796500100 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796102100 E2529796500300 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529796200400 E2529796600200 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529797200600 E2529797000000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529797201000 E2529797000400 01 (1) (2)

NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

CONF 001Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 50

DESCRIPTION OLD PART No. SEE NOTESCOMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795201300 (1)COMPARTMENT ASSY-OVHD STWG E2529795202500 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.

CONF 002Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200800 (1)COMPARTMENT ASSY-OVHD STWG E2529795200900 (1)COMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795201900 (1)COMPARTMENT ASSY-OVHD STWG E2529795202200 (1)COMPARTMENT ASSY-OVHD STWG E2529795202400 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 51

DESCRIPTION OLD PART No. SEE NOTESCOMPARTMENT ASSY-OVHD STWG E2529796000500 (1)COMPARTMENT ASSY-OVHD STWG E2529796100600 (1)COMPARTMENT ASSY-OVHD STWG E2529796100700 (1)COMPARTMENT ASSY-OVHD STWG E2529796200000COMPARTMENT ASSY-OVHD STWG E2529796200100COMPARTMENT ASSY-OVHD STWG E2529796200400 (1)COMPARTMENT ASSY-OVHD STWG E2529796200500 (1)COMPARTMENT ASSY-OVHD STWG E2529797200600 (1)COMPARTMENT ASSY-OVHD STWG E2529797201000 (1)COMPARTMENT ASSY-OVHD STWG E2529797202300 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.

CONF 003Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795100700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795202400 (1)COMPARTMENT ASSY-OVHD STWG E2529795202500 (1)COMPARTMENT ASSY-OVHD STWG E2529795202900 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)COMPARTMENT ASSY-OVHD STWG E2529795501000 (1)COMPARTMENT ASSY-OVHD STWG E2529795501100 (1)COMPARTMENT ASSY-OVHD STWG E2529796102000 (1)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 52

DESCRIPTION OLD PART No. SEE NOTESCOMPARTMENT ASSY-OVHD STWG E2529796102100 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.

CONF 004Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201300COMPARTMENT ASSY-OVHD STWG E2529795202500 (1)COMPARTMENT ASSY-OVHD STWG E2529795202700 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.

CONF 005Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 53

DESCRIPTION OLD PART No. SEE NOTESCOMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795202400 (1)COMPARTMENT ASSY-OVHD STWG E2529795202900 (1)COMPARTMENT ASSY-OVHD STWG E2529795203100 (1)COMPARTMENT ASSY-OVHD STWG E2529795402600 (1)COMPARTMENT ASSY-OVHD STWG E2529795402700 (1)COMPARTMENT ASSY-OVHD STWG E2529796000500 (1)COMPARTMENT ASSY-OVHD STWG E2529796100600 (1)COMPARTMENT ASSY-OVHD STWG E2529796100700 (1)COMPARTMENT ASSY-OVHD STWG E2529796200000 (1)COMPARTMENT ASSY-OVHD STWG E2529796200100 (1)COMPARTMENT ASSY-OVHD STWG E2529796200400 (1)COMPARTMENT ASSY-OVHD STWG E2529796200500 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.

CONF 006Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795201300 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 54

CONF 007Spare parts for task set A320-A-25-XX-1BPY-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795100700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200900 (1)COMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795201500 (1)COMPARTMENT ASSY-OVHD STWG E2529795202400 (1)COMPARTMENT ASSY-OVHD STWG E2529795402600 (1)COMPARTMENT ASSY-OVHD STWG E2529795402700 (1)COMPARTMENT ASSY-OVHD STWG E2529795500100 (1)COMPARTMENT ASSY-OVHD STWG E2529795500900 (1)COMPARTMENT ASSY-OVHD STWG E2529795501100 (1)COMPARTMENT ASSY-OVHD STWG E2529796100600 (1)COMPARTMENT ASSY-OVHD STWG E2529796100700 (1)COMPARTMENT ASSY-OVHD STWG E2529796102100 (1)COMPARTMENT ASSY-OVHD STWG E2529796200400 (1)COMPARTMENT ASSY-OVHD STWG E2529797200600 (1)COMPARTMENT ASSY-OVHD STWG E2529797201000 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 55

CONF ALL3. ACCOMPLISHMENT INSTRUCTIONS

Task set A320-A-25-XX-1BPY-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONSINCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICALWIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLYSERVICEABLE). WHEN YOU DO MAINTENANCE WORK, REPAIRS ORMODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS ANDTHE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION ANDDAMAGE TO THE ELECTRICAL WIRING INSTALLATION.IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given inother documents or in other sections of the Service Bulletin. When the words “refer to”are used and the operator has a procedure accepted by the local authority he belongs to,the accepted alternative procedure can be used. When the words “in accordance with”are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in thisService Bulletin do not constitute or affect the technical intent of the Service Bulletin.Operators can therefore, as deemed necessary, omit or add access and/or close-up stepsto add flexibility to their maintenance operations as long as the technical intent of theService Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Referto paragraph 1.J., References, for the definition of acronyms.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATIONTask Manpower

CONF 001TOTAL MAN-HOURS 24.50 h

CONF 002TOTAL MAN-HOURS 31.00 h

CONF 003TOTAL MAN-HOURS 28.50 h

CONF 004TOTAL MAN-HOURS 25.00 h

CONF 005TOTAL MAN-HOURS 30.00 h

CONF 006TOTAL MAN-HOURS 25.00 h

CONF 007TOTAL MAN-HOURS 33.25 h

CONF 001ELAPSED TIME (HOURS) 12.75 h


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 56

CONF 002ELAPSED TIME (HOURS) 16.25 h

CONF 003ELAPSED TIME (HOURS) 15.00 h

CONF 004ELAPSED TIME (HOURS) 13.00 h

CONF 005ELAPSED TIME (HOURS) 15.75 h

CONF 006ELAPSED TIME (HOURS) 13.00 h

CONF 007ELAPSED TIME (HOURS) 17.50 h

CONF ALLB. PREPARATION

(1) Task A320-A-25-XX-1BPY-01001-540A-A - Job Set-upJob Set-Up Information

Manpower/Resources/Skills

Man-hours 0.25 hMinimum Number of person 1Elapsed Time 0.25 hSkills Utility

Referenced Information

Manuals/Drawings References/Sheets

AMM Task 12-34-24-869-802Task 24-42-00-861-001

Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task12-34-24-869-802.

(b) Energize the ground service network, refer to Ref. AMM Task 24-42-00-861-001.(c) Make sure that the bin of the Overhead Stowage Compartment (OHSC) is empty.

If necessary:- Remove, identify and retain any installed equipment.- Remove, identify and retain any attachment assemblies from the bin.

NOTE: Items will be re-installed in the new bins.

C. PROCEDURECONF 001

(1) Task A320-A-25-XX-1BPY-01001-920A-A - Replace the Bin of the PivotingOverhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 20.50 h


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 57

Minimum Number of person 3Elapsed Time 10.25 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD01R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 5 CMPRTMNTE2529795000100 3 CMPRTMNTE2529795000200 5 CMPRTMNTE2529795000300 3 CMPRTMNTE2529795000400 5 CMPRTMNTE2529795000500 6 CMPRTMNTE2529795000600 3 CMPRTMNTE2529795000700 5 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795001300 1 CMPRTMNTE2529795002500 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

Part kit 251BPYD08R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 164 SCREW3 NAS1149CN832R 164 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 41 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 58

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 2F AL ST

1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(c) Replace bin assembly 2F AR STD


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 59

1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(d) Replace bin assembly 2F FL ST1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 60

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(e) Replace bin assembly 2F FR STD1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 61

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(f) Replace bin assembly 2F AL EE1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(g) Replace bin assembly 2F AR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 62

1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(h) Replace bin assembly 2F FL EE1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 63

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(i) Replace bin assembly 2F FR EE1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 64

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(j) Replace bin assembly 2F LH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001000  

(k) Replace bin assembly 2F AR MCU


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 65

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(l) Replace bin assembly 2F RH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 66

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001100  

(m) Replace bin assembly 2F FR MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 67

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002500  

(n) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600000  

(o) Replace bin assembly 2FP FR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 68

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600100  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 69

CONF 001

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 70

CONF 001

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 71

CONF 001

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 72

CONF 001

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 73

CONF 002(1) Task A320-A-25-XX-1BPY-01002-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 26.50 hMinimum Number of person 3Elapsed Time 13.25 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD02R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 7 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 2 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795000800 1 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001700 1 CMPRTMNTE2529795001900 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 1 CMPRTMNTE2529797000000 1 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 74

Part kit 251BPYD02R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529797000200 1 CMPRTMNTE2529797000400 2 CMPRTMNT

Part kit 251BPYD09R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 196 SCREW3 NAS1149CN832R 196 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 49 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 2F AL ST

1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 75

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(c) Replace bin assembly 2F AR STD1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 76

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(d) Replace bin assembly 2F FL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(e) Replace bin assembly 2F FR STD


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 77

1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(f) Replace bin assembly 2F AL EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 78

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(g) Replace bin assembly 2F AR EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 79

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(h) Replace bin assembly 2F FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(i) Replace bin assembly 2F FR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 80

1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(j) Replace bin assembly 2F LH SYM1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200800   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 81

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000800  

(k) Replace bin assembly 2F RH SYM1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 82

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000900  

(l) Replace bin assembly 2F LH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001000  

(m) Replace bin assembly 2F AR MCU


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 83

1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(n) Replace bin assembly 2F FR LOCK1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 84

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001700  

(o) Replace bin assembly 2F AR EE LOCK1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 85

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001900  

(p) Replace bin assembly 2F LH SYM EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002000  

(q) Replace bin assembly 2FP FL EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 86

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600000  

(r) Replace bin assembly 2FP FR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 87

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600100  

(s) Replace bin assembly 1FPC RH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796000500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 88

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796300100  

(t) Replace bin assembly 1FC LH1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500000  

(u) Replace bin assembly 1FC EE RH


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 89

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500100  

(v) Replace bin assembly 2FC LH STD1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 90

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600000  

(w) Replace bin assembly 2FC RH STD1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 91

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600100  

(x) Replace bin assembly 2FC LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600200  

(y) Replace bin assembly 2FC RH EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 92

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600300  

(z) Replace bin assembly 2FR LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529797200600   Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 93

3 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529797000000  

(aa) Replace bin assembly 2FRS EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529797201000   Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

3 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529797000400  

(ab) Replace bin assembly 2FR LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529797202300   Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

3 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529797000200  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 94

CONF 002

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 95

CONF 002

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 96

CONF 002

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 97

CONF 002

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 98

CONF 003(1) Task A320-A-25-XX-1BPY-01003-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 24.00 hMinimum Number of person 3Elapsed Time 12.00 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD03R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 8 CMPRTMNTE2529795000100 6 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 4 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 3 CMPRTMNTE2529795001300 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795002500 1 CMPRTMNTE2529795002700 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529795700600 1 CMPRTMNTE2529795700700 1 CMPRTMNTE2529796500200 1 CMPRTMNTE2529796500300 1 CMPRTMNT

Part kit 251BPYD10R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 192 SCREW3 NAS1149CN832R 192 WASHER


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 99

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 48 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 1F FR EE

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795100700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 2


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 100

3 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795300100  

(c) Replace bin assembly 2F AL ST1 Remove:

8 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

32 SCREW   Item (2) Discard

32 WASHER   Item (3) Discard

8 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

8 BRACKET 606A00306-000 Item 1

32 WASHER NAS1149CN832R Item 3

32 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

8 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(d) Replace bin assembly 2F AR STD


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 101

1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(e) Replace bin assembly 2F FL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 102

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(f) Replace bin assembly 2F FR STD1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 103

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(g) Replace bin assembly 2F AL EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(h) Replace bin assembly 2F AR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 104

1 Remove:

4 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

16 SCREW   Item (2) Discard

16 WASHER   Item (3) Discard

4 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

4 BRACKET 606A00306-000 Item 1

16 WASHER NAS1149CN832R Item 3

16 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

4 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(i) Replace bin assembly 2F FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 105

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(j) Replace bin assembly 2F FR EE1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 106

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(k) Replace bin assembly 2F AR MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(l) Replace bin assembly 2F LH SYM EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 107

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002000  

(m) Replace bin assembly 2F FR MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 108

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002500  

(n) Replace bin assembly 2F FL KANDU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 109

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002700  

(o) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600000  

(p) Replace bin assembly 2FP FR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 110

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600100  

(q) Replace bin assembly US 16 AL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795501000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discard


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 111

b Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795700600  

(r) Replace bin assembly US 16 AR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795501100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 112

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795700700  

(s) Replace bin assembly 1F CO C64 FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796102000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500200  

(t) Replace bin assembly 1F CO C64 FR EE


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 113

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796102100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500300  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 114

CONF 003

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 115

CONF 003

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 116

CONF 003

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 117

CONF 003

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 118

CONF 004(1) Task A320-A-25-XX-1BPY-01004-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 21.00 hMinimum Number of person 3Elapsed Time 10.50 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD04R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 7 CMPRTMNTE2529795000100 6 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 6 CMPRTMNTE2529795000400 3 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 2 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795002300 1 CMPRTMNTE2529795002500 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

Part kit 251BPYD11R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 168 SCREW3 NAS1149CN832R 168 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 42 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 119

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 2F AL ST

1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 120

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(c) Replace bin assembly 2F AR STD1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(d) Replace bin assembly 2F FL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 121

a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(e) Replace bin assembly 2F FR STD1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 122

c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(f) Replace bin assembly 2F AL EE1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 123

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(g) Replace bin assembly 2F AR EE1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(h) Replace bin assembly 2F FL EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 124

a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(i) Replace bin assembly 2F FR EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 125

c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(j) Replace bin assembly 2F LH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 126

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001000  

(k) Replace bin assembly 2F RH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001100  

(l) Replace bin assembly 2F AR MCU EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202700   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 127

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002300  

(m) Replace bin assembly 2F FR MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 128

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002500  

(n) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 129

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600000  

(o) Replace bin assembly 2FP FR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600100  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 130

CONF 004

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 131

CONF 004

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 132

CONF 004

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 133

CONF 004

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 134

CONF 005(1) Task A320-A-25-XX-1BPY-01005-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 25.50 hMinimum Number of person 3Elapsed Time 12.75 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD05R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 9 CMPRTMNTE2529795000100 6 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 7 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795002100 1 CMPRTMNTE2529795002700 1 CMPRTMNTE2529795600200 1 CMPRTMNTE2529795600300 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 1 CMPRTMNT

Part kit 251BPYD12R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 204 SCREW


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 135

Part kit 251BPYD12R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES3 NAS1149CN832R 204 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 51 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 2F AL ST

1 Remove:

9 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

36 SCREW   Item (2) Discard

36 WASHER   Item (3) Discard

9 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 136

c Install:

9 BRACKET 606A00306-000 Item 1

36 WASHER NAS1149CN832R Item 3

36 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

9 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(c) Replace bin assembly 2F AR STD1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 137

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(d) Replace bin assembly 2F FL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(e) Replace bin assembly 2F FR STD1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 138

a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(f) Replace bin assembly 2F AL EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 139

c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(g) Replace bin assembly 2F AR EE1 Remove:

3 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

12 SCREW   Item (2) Discard

12 WASHER   Item (3) Discard

3 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

3 BRACKET 606A00306-000 Item 1

12 WASHER NAS1149CN832R Item 3

12 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 140

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

3 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(h) Replace bin assembly 2F FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(i) Replace bin assembly 2F FR EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 141

a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(j) Replace bin assembly 2F AR MCU1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 142

c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(k) Replace bin assembly 2F LH SYM EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 143

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002000  

(l) Replace bin assembly 2F FL KANDU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002700  

(m) Replace bin assembly 2F RH SYM EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795203100   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 144

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002100  

(n) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795402600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 145

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600200  

(o) Replace bin assembly 2FP FR EE MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795402700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 146

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600300  

(p) Replace bin assembly 1FPC RH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796000500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796300100  

(q) Replace bin assembly 1FC LH1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100600   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 147

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500000  

(r) Replace bin assembly 1FC EE RH1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 148

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500100  

(s) Replace bin assembly 2FC LH STD1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 149

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600000  

(t) Replace bin assembly 2FC RH STD1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600100  

(u) Replace bin assembly 2FC LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200400   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 150

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600200  

(v) Replace bin assembly 2FC RH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 151

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600300  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 152

CONF 005

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 153

CONF 005

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 154

CONF 005

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 155

CONF 005

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 156

CONF 006(1) Task A320-A-25-XX-1BPY-01006-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 21.00 hMinimum Number of person 3Elapsed Time 10.50 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD06R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 5 CMPRTMNTE2529795000100 2 CMPRTMNTE2529795000200 5 CMPRTMNTE2529795000300 4 CMPRTMNTE2529795000400 5 CMPRTMNTE2529795000500 6 CMPRTMNTE2529795000600 4 CMPRTMNTE2529795000700 5 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001100 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNT

Part kit 251BPYD11R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 168 SCREW3 NAS1149CN832R 168 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 42 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 157

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 2F AL ST

1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 158

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(c) Replace bin assembly 2F AR STD1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(d) Replace bin assembly 2F FL ST1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 159

a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(e) Replace bin assembly 2F FR STD1 Remove:

4 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

16 SCREW   Item (2) Discard

16 WASHER   Item (3) Discard

4 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 160

c Install:

4 BRACKET 606A00306-000 Item 1

16 WASHER NAS1149CN832R Item 3

16 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

4 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(f) Replace bin assembly 2F AL EE1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 161

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(g) Replace bin assembly 2F AR EE1 Remove:

6 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

24 SCREW   Item (2) Discard

24 WASHER   Item (3) Discard

6 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

6 BRACKET 606A00306-000 Item 1

24 WASHER NAS1149CN832R Item 3

24 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

6 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(h) Replace bin assembly 2F FL EE1 Remove:

4 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 162

a Remove:

16 SCREW   Item (2) Discard

16 WASHER   Item (3) Discard

4 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

4 BRACKET 606A00306-000 Item 1

16 WASHER NAS1149CN832R Item 3

16 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

4 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(i) Replace bin assembly 2F FR EE1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 163

c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(j) Replace bin assembly 2F LH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 164

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001000  

(k) Replace bin assembly 2F AR MCU1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(l) Replace bin assembly 2F RH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201300   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 165

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001100  

(m) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 166

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600000  

(n) Replace bin assembly 2FP FR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795400700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 167

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600100  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 168

CONF 006

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 169

CONF 006

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 170

CONF 006

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 171

CONF 006

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 172

CONF 007(1) Task A320-A-25-XX-1BPY-01007-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 28.50 hMinimum Number of person 3Elapsed Time 14.25 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPYD07R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 7 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 8 CMPRTMNTE2529795000400 4 CMPRTMNTE2529795000500 4 CMPRTMNTE2529795000600 2 CMPRTMNTE2529795000700 2 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001400 1 CMPRTMNTE2529795002000 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600200 1 CMPRTMNTE2529795600300 1 CMPRTMNTE2529795700100 1 CMPRTMNTE2529795700300 1 CMPRTMNTE2529795700700 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796500300 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529797000000 1 CMPRTMNTE2529797000400 1 CMPRTMNT


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 173

Part kit 251BPYD13R00ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 220 SCREW3 NAS1149CN832R 220 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 55 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.

Referenced Information

Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure(a) Standard Practices

1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 1F FR EE

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795100700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 174

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795300100  

(c) Replace bin assembly 2F AL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200000   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 175

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000000  

(d) Replace bin assembly 2F AR STD1 Remove:

5 COMPARTMENT ASSY-OVHD STWG

E2529795200100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

20 SCREW   Item (2) Discard

20 WASHER   Item (3) Discard

5 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

5 BRACKET 606A00306-000 Item 1

20 WASHER NAS1149CN832R Item 3

20 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

5 COMPARTMENT ASSY-OVHD STWG

E2529795000100  

(e) Replace bin assembly 2F FL ST1 Remove:

7 COMPARTMENT ASSY-OVHD STWG

E2529795200200   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 176

a Remove:

28 SCREW   Item (2) Discard

28 WASHER   Item (3) Discard

7 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

7 BRACKET 606A00306-000 Item 1

28 WASHER NAS1149CN832R Item 3

28 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

7 COMPARTMENT ASSY-OVHD STWG

E2529795000200  

(f) Replace bin assembly 2F FR STD1 Remove:

8 COMPARTMENT ASSY-OVHD STWG

E2529795200300   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

32 SCREW   Item (2) Discard

32 WASHER   Item (3) Discard

8 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 177

c Install:

8 BRACKET 606A00306-000 Item 1

32 WASHER NAS1149CN832R Item 3

32 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

8 COMPARTMENT ASSY-OVHD STWG

E2529795000300  

(g) Replace bin assembly 2F AL EE1 Remove:

4 COMPARTMENT ASSY-OVHD STWG

E2529795200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

16 SCREW   Item (2) Discard

16 WASHER   Item (3) Discard

4 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

4 BRACKET 606A00306-000 Item 1

16 WASHER NAS1149CN832R Item 3

16 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 178

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

4 COMPARTMENT ASSY-OVHD STWG

E2529795000400  

(h) Replace bin assembly 2F AR EE1 Remove:

4 COMPARTMENT ASSY-OVHD STWG

E2529795200500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

16 SCREW   Item (2) Discard

16 WASHER   Item (3) Discard

4 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

4 BRACKET 606A00306-000 Item 1

16 WASHER NAS1149CN832R Item 3

16 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

4 COMPARTMENT ASSY-OVHD STWG

E2529795000500  

(i) Replace bin assembly 2F FL EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200600   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 179

a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000600  

(j) Replace bin assembly 2F FR EE1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795200700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 180

c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795000700  

(k) Replace bin assembly 2F RH SYM1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795200900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 181

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795000900  

(l) Replace bin assembly 2F LH 3FS1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001000  

(m) Replace bin assembly 2F AR MCU1 Remove:

2 COMPARTMENT ASSY-OVHD STWG

E2529795201200   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 182

a Remove:

8 SCREW   Item (2) Discard

8 WASHER   Item (3) Discard

2 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

2 BRACKET 606A00306-000 Item 1

8 WASHER NAS1149CN832R Item 3

8 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

2 COMPARTMENT ASSY-OVHD STWG

E2529795001300  

(n) Replace bin assembly 2F FL KANDU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795201500   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 183

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795001400  

(o) Replace bin assembly 2F LH SYM EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795202400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 184

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795002000  

(p) Replace bin assembly 2FP FL EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795402600   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600200  

(q) Replace bin assembly 2FP FR EE MCU1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795402700   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 185

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795600300  

(r) Replace bin assembly US1 AR STD1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795500100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 186

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795700100  

(s) Replace bin assembly US3 FR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795500900   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 187

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795700300  

(t) Replace bin assembly US 16 AR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795501100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529795700700  

(u) Replace bin assembly 1FC LH1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100600   Discard

2 Replace the X-fixation bracket in the housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 188

a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500000  

(v) Replace bin assembly 1FC EE RH1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796100700   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 189

c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500100  

(w) Replace bin assembly 1F CO C64 FR EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796102100   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-001 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 190

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796500300  

(x) Replace bin assembly 2FC LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529796200400   Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW   Item (2) Discard

4 WASHER   Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

  Non Aqueous Cleaner -General

08BAA9  

and

  Textile - Lint free Cotton 14SBA1  c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529796600200  

(y) Replace bin assembly 2FR LH EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529797200600   Discard

2 Reidentify the OHSC housing.


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 191

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

3 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529797000000  

(z) Replace bin assembly 2FRS EE1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529797201000   Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

3 Install:

1 COMPARTMENT ASSY-OVHD STWG

E2529797000400  


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYBin Installation - Typical

Page 192

CONF 007

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPY-A-FAPE3-01CJR-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01 SHEET 1/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 193

CONF 007

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CV9-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01 SHEET 2/2REV 00 Jun 13/19 A320-25-1BPYFixation Bracket Replacement

Page 194

CONF 007

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPY-A-FAPE3-01CVA-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYHousing Placard Location

Page 195

CONF 007

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPY IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPY-A-FAPE3-01HYG-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 196

CONF ALL(2) Task A320-A-25-XX-1BPY-01001-900A-A - Reidentify the Overhead Stowage

Compartment AssembliesJob Set-Up Information

Manpower/Resources/Skills

Man-hours 1.50 hMinimum Number of person 1Elapsed Time 1.50 hSkills Cabin

Procedure(a) Reidentify the OHSC assembly.

1 To find the correct PN for the placard to be installed, refer to Ref. AppendixPART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUS Material,Logistics and Suppliers, Customer Order Fulfilment.

2 Install the OHSC assembly placard, refer to Ref. Fig. OHSC AssemblyPlacard Location.


A318/A319/A320/A321SERVICE BULLETIN

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01GWY-A-001-01 SHEET 1/1REV 00 Jun 13/19 A320-25-1BPYOHSC Assembly Placard Location

Page 197

CONF ALL

Z200

A

TYPICAL

TYPICAL

A

B

B

SB25-1BPY IMPLEMENTED

NEW P/N: E25294XXXXXXXX

NOTE:MAKE EXISTING P/N UNREADABLE01

01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

02 03

C

C

ICN-A320-A-25XX1BPY-A-FAPE3-01GWY-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 198

D. PREPARATION FOR TESTNone

E. TESTCONF 001 004 006

(1) Task A320-A-25-XX-1BPY-01001-320A-A - Operational TestJob Set-Up Information

Manpower/Resources/Skills

Man-hours 2.00 hMinimum Number of person 1Elapsed Time 2.00 hSkills Cabin

Referenced Information

Manuals/Drawings References/SheetsAMM Task 25-24-00-710-002

Procedure(a) Open and close the bin to check the correct operation.(b) If necessary do the adjustment of the bin, refer to Ref. AMM Task

25-24-00-710-002.CONF 002 003 005

(1) Task A320-A-25-XX-1BPY-01002-320A-A - Operational TestJob Set-Up Information

Manpower/Resources/Skills

Man-hours 2.50 hMinimum Number of person 1Elapsed Time 2.50 hSkills Cabin

Referenced Information

Manuals/Drawings References/SheetsAMM Task 25-24-00-710-002

Procedure(a) Open and close the bin to check the correct operation.(b) If necessary do the adjustment of the bin, refer to Ref. AMM Task

25-24-00-710-002.CONF 007

(1) Task A320-A-25-XX-1BPY-01003-320A-A - Operational TestJob Set-Up Information

Manpower/Resources/Skills

Man-hours 2.75 hMinimum Number of person 1


A318/A319/A320/A321SERVICE BULLETIN

REV 00 Jun 13/19 A320-25-1BPYPage 199

Elapsed Time 2.75 hSkills Cabin

Referenced Information

Manuals/Drawings References/SheetsAMM Task 25-24-00-710-002

Procedure(a) Open and close the bin to check the correct operation.(b) If necessary do the adjustment of the bin, refer to Ref. AMM Task

25-24-00-710-002.CONF ALL

F. CLOSE-UP(1) Task A320-A-25-XX-1BPY-01001-740A-A - Close-up

Job Set-Up InformationManpower/Resources/Skills

Man-hours 0.25 hMinimum Number of person 1Elapsed Time 0.25 hSkills Utility

Procedure(a) Make sure that the OHSC bins are clean and clear of tools and other items of

equipment.1 Open the OHSC bin.2 Install, where necessary, the identified removed equipment in the OHSC

bin.3 Close the OHSC bin.

(b) Put the aircraft back to its initial configuration.G. ADMINISTRATIVE

(1) Task A320-A-25-XX-1BPY-01001-90AA-A - Administrative

ProcedureConfirm in the applicable aircraft records that you have completed all the work definedin this Service Bulletin task set as required.


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

REV 00 Jun 13/19 A320-25-1BPYPage 200

APPENDIXA. PART NUMBER ROLL INFORMATION

PART NUMBER ROLL INFORMATIONThis Appendix gives information about the Part Number roll after accomplishment of thisService Bulletin.


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01GX2-A-002-01 SHEET 1/5REV 00 Jun 13/19 A320-25-1BPYPart Number Roll Information

Page 201

CONF ALL

TOP OHSC 4F E252-94000-000-00 E252-94000-006-00D252-93571-000-00

E252-94000-004-00 E252-94000-010-00D252-93571-004-00

E252-94001-000-00 E252-94001-006-00D252-93571-010-00

E252-94001-004-00 E252-94001-014-00D252-93571-010-00

E252-94001-008-00 E252-94001-018-00D252-93571-012-00

E252-94001-010-00 E252-94001-016-00D252-93571-014-00

E252-94001-022-00 E252-94001-020-00D252-93571-016-00

E252-94002-000-00 E252-94002-020-00D252-93571-018-00

E252-94002-006-00 E252-94002-028-00D252-93571-024-00

E252-94002-008-00 E252-94002-030-00D252-93571-026-00

E252-94002-010-00 E252-94002-032-00D252-93571-028-00

E252-94002-016-00 E252-94002-038-00D252-93571-032-00

E252-94002-018-00 E252-94002-022-00D252-93571-034-00

TOP OHSC 4F TS E252-94003-002-00 E252-94003-020-00D252-93571-036-00

TOP OHSC 4F TS E252-94003-006-00 E252-94003-024-00D252-93571-040-00

TOP OHSC 4F TS E252-94003-008-00 E252-94003-026-00D252-93571-042-00

TOP OHSC 4F TS E252-94003-014-00 E252-94002-028-00D252-93571-046-00

TOP OHSC 4F TS E252-94003-018-00 E252-94003-034-00D252-93571-050-00

E252-94004-000-00 E252-94004-006-00D252-93571-052-00

E252-94004-002-00 E252-94004-010-00D252-93571-054-00

E252-94005-000-00 E252-94005-008-00D252-93571-058-00

E252-94005-002-00 E252-94005-010-00D252-93571-060-00

E252-94005-006-00 E252-94005-012-00D252-93571-062-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F E252-94006-000-00 E252-94006-006-00D252-93571-064-00

E252-94006-002-00 E252-94006-010-00D252-93571-066-00

E252-94006-004-00 E252-94006-008-00D252-93571-068-00

E252-94007-000-00 E252-94007-006-00D252-93571-070-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94007-002-00 E252-94007-010-00

E252-94007-004-00 E252-94007-008-00

E252-94010-000-00 E252-94010-006-00

E252-94010-002-00 E252-94010-010-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

D252-93571-072-00

D252-93571-074-00

D252-93571-076-00

D252-93571-078-00

E252-94004-004-00 E252-94004-008-00D252-93571-056-00TOP OHSC 4F

D252-93646-000-00

D252-93646-004-00

D252-93646-006-00

D252-93646-010-00

D252-93646-012-00

D252-93646-014-00

D252-93646-016-00

D252-93646-018-00

D252-93646-024-00

D252-93646-026-00

D252-93646-028-00

D252-93646-030-00

D252-93646-032-00

D252-93646-034-00

D252-93646-038-00

D252-93646-040-00

D252-93646-042-00

D252-93646-044-00

D252-93646-046-00

D252-93646-048-00

D252-93646-102-00

D252-93646-050-00

D252-93646-052-00

D252-93646-054-00

D252-93646-056-00

D252-93646-058-00

D252-93646-060-00

D252-93646-062-00

D252-93646-064-00

D252-93646-066-00

D252-93646-068-00

D252-93646-070-00

PART NUMBER ROLL

TOP OHSCOHSC NAME

AFTER SB25-1BPZPRE PN TOP OHSC

BEFORE SB25-1BPZPRE PN

HOUSINGPOST PN

HOUSINGPRE PN TOP OHSC PLACARD PN

TOP OHSCPOST PN

HOUSINGPLACARD PN

E252-97904-018-00

E252-97921-009-00

E252-97914-000-00

E252-97914-000-00

E252-97931-009-00

E252-97915-001-00

E252-97931-009-00

E252-97904-000-00

E252-97904-007-00

E252-97904-004-00

E252-97904-000-00

E252-97921-015-00

E252-97921-015-00

E252-97914-015-00

E252-97914-007-00

E252-97914-004-00

E252-97914-015-00

E252-97914-015-00

E252-97904-003-00

E252-97904-003-00

E252-97914-003-00

E252-97914-003-00

E252-97914-003-00

E252-97904-029-00

E252-97904-029-00

E252-97904-029-00

E252-97914-030-00

E252-97914-030-00

E252-97914-030-00

E252-97904-006-00

E252-97904-006-00

E252-97904-003-00

E252-97924-010-00

E252-97940-008-00

E252-97934-000-00

E252-97934-000-00

E252-97941-004-00

E252-97935-001-00

E252-97941-004-00

E252-97924-000-00

E252-97924-005-00

E252-97924-003-00

E252-97924-000-00

E252-97940-009-00

E252-97940-009-00

E252-97934-012-00

E252-97934-007-00

E252-97934-004-00

E252-97934-012-00

E252-97934-012-00

E252-97924-002-00

E252-97924-002-00

E252-97934-003-00

E252-97934-003-00

E252-97934-003-00

E252-97924-015-00

E252-97924-015-00

E252-97924-015-00

E252-97934-019-00

E252-97934-019-00

E252-97934-019-00

E252-97924-004-00

E252-97924-004-00

E252-97924-002-00

D252-93648-044-00

D252-93648-186-00

D252-93648-108-00

D252-93648-108-00

D252-93577-014-00

D252-93648-148-00

D252-93577-014-00

D252-93648-024-00

D252-93648-034-00

D252-93648-030-00

D252-93648-024-00

D252-93648-186-00

D252-93648-186-00

D252-93648-130-00

D252-93648-120-00

D252-93648-116-00

D252-93648-130-00

D252-93648-130-00

D252-93648-028-00

D252-93648-028-00

D252-93648-028-00

D252-93648-114-00

D252-93648-114-00

D252-93648-114-00

D252-93648-054-00

D252-93648-054-00

D252-93648-054-00

D252-93648-140-00

D252-93648-140-00

D252-93648-140-00

D252-93648-032-00

D252-93648-032-00

ICN-A320-A-25XX1BPY-A-FAPE3-01GX2-A-002-01


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01GX3-A-002-01 SHEET 2/5REV 00 Jun 13/19 A320-25-1BPYPart Number Roll Information

Page 202

CONF ALL

E252-94011-000-00 E252-94011-006-00

E252-94011-002-00 E252-94011-010-00

E252-94011-004-00 E252-94011-008-00

E252-94012-000-00 E252-94012-006-00

E252-94012-002-00 E252-94012-010-00

E252-94012-004-00 E252-94012-008-00

E252-94013-000-00 E252-94013-006-00

E252-94013-002-00 E252-94013-010-00

E252-94013-004-00 E252-94013-008-00

E252-94014-000-00 E252-94014-024-00

E252-94014-004-00 E252-94014-032-00

E252-94014-006-00 E252-94014-028-00

E252-94014-008-00 E252-94014-022-00

E252-94014-014-00 E252-94014-026-00

TOP OHSC 4F TS

E252-94014-016-00 E252-94014-018-00

E252-94015-000-00 E252-94015-016-00

E252-94015-004-00 E252-94015-022-00

E252-94015-006-00 E252-94015-024-00

E252-94015-012-00 E252-94015-030-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F TS

TOP OHSC 4F TS

TOP OHSC 4F TS

E252-94015-014-00 E252-94015-018-00

E252-94016-000-00 E252-94016-008-00

E252-94016-004-00 E252-94016-012-00

E252-94016-006-00 E252-94016-014-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F TS

D252-93571-082-00

D252-93571-084-00

D252-93571-086-00

D252-93571-088-00

D252-93571-090-00

D252-93571-092-00

D252-93571-094-00

D252-93571-096-00

D252-93571-098-00

D252-93571-100-00

D252-93571-104-00

D252-93571-106-00

D252-93571-108-00

D252-93571-112-00

D252-93571-114-00

D252-93571-116-00

D252-93571-120-00

D252-93571-122-00

D252-93571-126-00

D252-93571-128-00

D252-93571-130-00

D252-93571-134-00

D252-93571-136-00

E252-94017-006-00 E252-94017-022-00

E252-94017-008-00 E252-94017-024-00

E252-94017-010-00 E252-94017-026-00

E252-94017-012-00 E252-94017-016-00

E252-94018-000-00 E252-94018-012-00

E252-94018-002-00 E252-94018-018-00

E252-94018-008-00 E252-94018-014-00

E252-94018-010-00 E252-94018-016-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

D252-93571-142-00

D252-93571-144-00

D252-93571-146-00

D252-93571-148-00

D252-93571-150-00

D252-93571-152-00

D252-93571-158-00

D252-93571-160-00

E252-94010-004-00 E252-94010-008-00TOP OHSC 4F D252-93571-080-00 D252-93646-072-00

D252-93646-074-00

D252-93646-076-00

D252-93646-078-00

D252-93646-080-00

D252-93646-082-00

D252-93646-084-00

D252-93646-086-00

D252-93646-088-00

D252-93646-090-00

D252-93646-092-00

D252-93646-096-00

D252-93646-098-00

D252-93646-100-00

D252-93646-104-00

D252-93646-108-00

D252-93646-106-00

D252-93646-112-00

D252-93646-114-00

D252-93646-118-00

D252-93646-120-00

D252-93646-122-00

D252-93646-126-00

D252-93646-128-00

D252-93646-134-00

D252-93646-136-00

D252-93646-138-00

D252-93646-140-00

D252-93646-142-00

D252-93646-144-00

D252-93646-148-00

D252-93646-150-00

PART NUMBER ROLL

TOP OHSCOHSC NAME

AFTER SB25-1BPZPRE PN TOP OHSC

BEFORE SB25-1BPZPRE PN

HOUSINGPOST PN

HOUSINGPRE PN TOP OHSC PLACARD PN

TOP OHSCPOST PN

HOUSINGPLACARD PN

E252-97914-006-00

E252-97914-006-00

E252-97914-006-00

E252-97904-028-00

E252-97904-028-00

E252-97904-028-00

E252-97914-025-00

E252-97914-025-00

E252-97914-025-00

E252-97904-021-00

E252-97904-021-00

E252-97904-021-00

E252-97921-019-00

E252-97904-021-00

E252-97904-021-00

E252-97914-026-00

E252-97914-026-00

E252-97914-026-00

E252-97931-014-00

E252-97931-014-00

E252-97904-024-00

E252-97904-024-00

E252-97904-024-00

E252-97914-024-00

E252-97914-011-00

E252-97914-011-00

E252-97914-011-00

E252-97904-008-00

E252-97904-008-00

E252-97904-008-00

E252-97921-006-00

E252-97904-006-00

E252-97934-006-00

E252-97934-006-00

E252-97934-006-00

E252-97924-014-00

E252-97924-014-00

E252-97924-014-00

E252-97934-016-00

E252-97934-016-00

E252-97934-016-00

E252-97924-012-00

E252-97924-012-00

E252-97924-012-00

E252-97940-012-00

E252-97924-012-00

E252-97924-012-00

E252-97934-017-00

E252-97934-017-00

E252-97934-017-00

E252-97941-009-00

E252-97941-009-00

E252-97924-013-00

E252-97924-013-00

E252-97924-013-00

E252-97934-015-00

E252-97934-010-00

E252-97934-010-00

E252-97934-010-00

E252-97924-006-00

E252-97924-006-00

E252-97924-006-00

E252-97940-006-00

E252-97924-004-00 D252-93648-032-00

D252-93648-118-00

D252-93648-118-00

D252-93648-118-00

D252-93648-052-00

D252-93648-052-00

D252-93648-052-00

D252-93648-134-00

D252-93648-134-00

D252-93648-134-00

D252-93648-048-00

D252-93648-048-00

D252-93648-048-00

D252-93648-194-00

D252-93648-048-00

D252-93648-048-00

D252-93648-136-00

D252-93648-136-00

D252-93648-136-00

D252-93577-020-00

D252-93577-020-00

D252-93648-050-00

D252-93648-050-00

D252-93648-050-00

D252-93648-132-00

D252-93648-126-00

D252-93648-126-00

D252-93648-126-00

D252-93648-036-00

D252-93648-036-00

D252-93648-036-00

D252-93648-182-00

ICN-A320-A-25XX1BPY-A-FAPE3-01GX3-A-002-01


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01GX4-A-002-01 SHEET 3/5REV 00 Jun 13/19 A320-25-1BPYPart Number Roll Information

Page 203

CONF ALL

E252-94019-002-00 E252-94019-012-00

E252-94019-004-00 E252-94019-014-00

E252-94019-008-00 E252-94019-018-00

E252-94020-006-00 E252-94020-022-00

E252-94020-012-00 E252-94020-028-00

E252-94020-014-00 E252-94020-030-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94021-006-00 E252-94021-022-00

E252-94021-008-00 E252-94021-030-00

E252-94022-008-00 E252-94022-026-00

E252-94022-014-00 E252-94022-032-00

E252-94022-016-00 E252-94022-034-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94021-014-00 E252-94021-028-00TOP OHSC 4F

D252-93571-164-00

D252-93571-166-00

D252-93571-170-00

D252-93571-178-00

D252-93571-182-00

D252-93571-184-00

D252-93571-192-00

D252-93571-194-00

D252-93572-008-00

D252-93572-012-00

D252-93572-014-00

D252-93571-198-00

E252-94023-008-00 E252-94023-026-00

E252-94023-014-00 E252-94023-032-00

E252-94023-016-00 E252-94023-034-00

E252-94024-000-00 E252-94024-008-00

E252-94024-002-00 E252-94024-010-00

E252-94024-006-00 E252-94024-014-00

E252-94025-000-00 E252-94025-008-00

E252-94025-002-00 E252-94025-010-00

E252-94025-006-00 E252-94025-014-00

E252-94026-006-00 E252-94026-022-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94026-012-00 E252-94026-028-00TOP OHSC 4F

E252-94026-014-00 E252-94026-030-00TOP OHSC 4F

E252-94027-006-00 E252-94027-022-00TOP OHSC 4F

E252-94027-012-00 E252-94027-028-00TOP OHSC 4F

E252-94027-014-00 E252-94027-030-00TOP OHSC 4F

E252-94028-006-00 E252-94028-026-00TOP OHSC 4F

E252-94028-014-00 E252-94028-034-00TOP OHSC 4F

E252-94028-016-00 E252-94028-020-00TOP OHSC 4F

E252-94029-006-00 E252-94029-026-00TOP OHSC 4F

D252-93572-024-00

D252-93572-028-00

D252-93572-030-00

D252-93572-032-00

D252-93572-034-00

D252-93572-038-00

D252-93572-040-00

D252-93572-042-00

D252-93572-046-00

D252-93572-052-00

D252-93572-056-00

D252-93572-058-00

D252-93572-066-00

D252-93572-070-00

D252-93572-072-00

D252-93572-080-00

D252-93572-084-00

D252-93572-086-00

D252-93572-094-00

E252-94019-000-00 E252-94019-010-00TOP OHSC 4F D252-93571-162-00 D252-93646-152-00

D252-93646-154-00

D252-93646-156-00

D252-93646-158-00

D252-93646-164-00

D252-93646-166-00

D252-93646-168-00

D252-93646-174-00

D252-93646-176-00

D252-93646-178-00

D252-93646-186-00

D252-93646-188-00

D252-93646-190-00

D252-93646-198-00

D252-93647-000-00

D252-93647-002-00

D252-93647-004-00

D252-93647-006-00

D252-93647-008-00

D252-93647-010-00

D252-93647-012-00

D252-93647-014-00

D252-93647-018-00

D252-93647-020-00

D252-93647-022-00

D252-93647-028-00

D252-93647-030-00

D252-93647-032-00

D252-93647-038-00

D252-93647-040-00

D252-93647-042-00

D252-93647-048-00

PART NUMBER ROLL

TOP OHSCOHSC NAME

AFTER SB25-1BPZPRE PN TOP OHSC

BEFORE SB25-1BPZPRE PN

HOUSINGPOST PN

HOUSINGPRE PN TOP OHSC PLACARD PN

TOP OHSCPOST PN

HOUSINGPLACARD PN

E252-97934-018-00

E252-97934-018-00

E252-97934-021-00

E252-97924-008-00

E252-97940-011-00

E252-97940-011-00

E252-97934-008-00

E252-97941-001-00

E252-97924-017-00

E252-97940-001-00

E252-97940-014-00

E252-97941-001-00

E252-97934-022-00

E252-97941-000-00

E252-97941-012-00

E252-97926-000-00

E252-97926-000-00

E252-97926-001-00

E252-97936-000-00

E252-97936-000-00

E252-97936-001-00

E252-97924-001-00

E252-97940-002-00

E252-97940-002-00

E252-97934-001-00

E252-97941-007-00

E252-97941-007-00

E252-97924-011-00

E252-97940-010-00

E252-97940-010-00

E252-97934-002-00

E252-97934-018-00

E252-97914-027-00

E252-97914-027-00

E252-97914-034-00

E252-97904-016-00

E252-97921-017-00

E252-97921-017-00

E252-97914-008-00

E252-97931-002-00

E252-97904-037-00

E252-97921-001-00

E252-97921-021-00

E252-97931-002-00

E252-97914-037-00

E252-97931-001-00

E252-97931-021-00

E252-97906-000-00

E252-97906-000-00

E252-97906-003-00

E252-97916-000-00

E252-97916-000-00

E252-97916-003-00

E252-97904-001-00

E252-97921-002-00

E252-97921-002-00

E252-97914-001-00

E252-97931-012-00

E252-97931-012-00

E252-97904-020-00

E252-97921-016-00

E252-97921-016-00

E252-97914-002-00

E252-97914-027-00 D252-93648-138-00

D252-93648-138-00

D252-93648-138-00

D252-93648-142-00

D252-93648-040-00

D252-93648-192-00

D252-93648-192-00

D252-93648-122-00

D252-93577-012-00

D252-93577-012-00

D252-93648-058-00

D252-93648-174-00

D252-93577-008-00

D252-93648-144-00

D252-93577-010-00

D252-93577-026-00

D252-93648-064-00

D252-93648-064-00

D252-93648-066 00

D252-93648-152-00

D252-93648-152-00

D252-93648-154-00

D252-93648-026-00

D252-93648-176-00

D252-93648-176-00

D252-93648-110-00

D252-93577-016-00

D252-93577-016-00

D252-93648-046-00

D252-93648-190-00

D252-93648-190-00

D252-93648-112-00

ICN-A320-A-25XX1BPY-A-FAPE3-01GX4-A-002-01


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01GX5-A-003-01 SHEET 4/5REV 00 Jun 13/19 A320-25-1BPYPart Number Roll Information

Page 204

CONF ALL

E252-94029-012-00 E252-94029-030-00TOP OHSC 4F

E252-94029-014-00 E252-94029-018-00TOP OHSC 4F

E252-94040-004-00 E252-94040-012-00TOP OHSC 4F

D252-93572-098-00

D252-93572-100-00

D252-93572-104-00

E252-94040-006-00 E252-94040-014-00TOP OHSC 4F

E252-94041-004-00 E252-94041-012-00TOP OHSC 4F

E252-94041-006-00 E252-94041-014-00TOP OHSC 4F

E252-94042-004-00 E252-94042-012-00TOP OHSC 4F

E252-94042-006-00 E252-94042-014-00TOP OHSC 4F

E252-94043-004-00 E252-94043-012-00TOP OHSC 4F

E252-94043-006-00 E252-94043-014-00TOP OHSC 4F

E252-94044-004-00 E252-94044-012-00TOP OHSC 4F

E252-94044-006-00 E252-94044-014-00TOP OHSC 4F

E252-94045-004-00 E252-94045-010-00TOP OHSC 4F

E252-94048-008-00 E252-94048-026-00

E252-94048-010-00 E252-94048-028-00

E252-94048-012-00 E252-94048-030-00

E252-94048-014-00 E252-94048-018-00

E252-94049-008-00 E252-94049-022-00

E252-94049-010-00 E252-94049-024-00

E252-94049-012-00 E252-94049-026-00

E252-94052-006-00 E252-94052-014-00

E252-94053-006-00 E252-94053-016-00

TOP OHSC 2FR E252-94054-002-00 E252-94054-006-00

TOP OHSC 2FC UP AIR

TOP OHSC 2FC UP AIR

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

D252-93572-106-00

D252-93572-110-00

D252-93572-112-00

D252-93572-116-00

D252-93572-118-00

D252-93572-122-00

D252-93572-124-00

D252-93572-128-00

D252-93572-130-00

D252-93572-134-00

D252-93572-142-00

D252-93572-144-00

D252-93572-146-00

D252-93572-148-00

D252-93572-154-00

D252-93572-156-00

D252-93572-158-00

D252-93572-166-00

D252-93572-174-00

D252-93572-178-00

E252-94055-004-00 E252-94055-010-00TOP OHSC 2FR

E252-94056-002-00 E252-94056-006-00TOP OHSC 2FC

E252-94057-002-00 E252-94057-006-00TOP OHSC 2FC

E252-94058-006-00 E252-94058-014-00TOP OHSC 2F

E252-94059-006-00 E252-94059-014-00TOP OHSC 2F

E252-94060-006-00 E252-94060-014-00TOP OHSC 2FC

E252-94061-008-00 E252-94061-012-00TOP OHSC 2FC

E252-94062-002-00 E252-94062-016-00

E252-94062-008-00 E252-94062-022-00

TOP OHSC 2FR

TOP OHSC 2FR

D252-93572-186-00

D252-93572-190-00

D252-93572-194-00

D252-93573-002-00

D252-93573-010-00

D252-93573-016-00

D252-93573-024-00

D252-93573-028-00

D252-93573-032-00

D252-93647-050-00

D252-93647-052-00

D252-93647-054-00

D252-93647-056-00

D252-93647-058-00

D252-93647-060-00

D252-93647-062-00

D252-93647-064-00

D252-93647-066-00

D252-93647-068-00

D252-93647-070-00

D252-93647-072-00

D252-93647-074-00

D252-93647-082-00

D252-93647-084-00

D252-93647-086-00

D252-93647-088-00

D252-93647-094-00

D252-93647-096-00

D252-93647-098-00

D252-93647-104-00

D252-93647-110-00

D252-93647-114-00

D252-93647-120-00

D252-93647-124-00

D252-93647-128-00

D252-93647-134-00

D252-93647-140-00

D252-93647-144-00

D252-93647-150-00

D252-93647-154-00

D252-93647-156-00

PART NUMBER ROLL

OHSC NAMEAFTER SB25-1BPZBEFORE SB25-1BPZ TOP OHSC

PRE PN TOP OHSC PRE PNHOUSING

POST PNHOUSING

PRE PN TOP OHSC PLACARD PNTOP OHSCPOST PN

HOUSINGPLACARD PN

E252-97931-013-00

E252-97931-013-00

E252-97904-006-00

E252-97904-006-00

E252-97904-006-00

E252-97904-006-00

E252-97921-004-00

E252-97921-020-00

E252-97931-015-00

E252-97931-020-00

E252-97921-005-00

E252-97921-018-00

E252-97921-005-00

E252-97903-002-00

E252-97903-003-00

E252-97903-004-00

E252-97903-034-00

E252-97913-000-00

E252-97913-034-00

E252-97913-004-00

E252-97907-004-00

E252-97917-004-00

E252-97908-000-00

E252-97918-000-00

E252-97907-000-00

E252-97917-000-00

E252-97902-000-00

E252-97912-000-00

E252-97907-045-00

E252-97917-046-00

E252-97908-003-00

E252-97908-041-00

E252-97941-008-00

E252-97941-008-00

E252-97924-004-00

E252-97924-004-00

E252-97924-006-00

E252-97924-006-00

E252-97940-004-00

E252-97940-013-00

E252-97941-010-00

E252-97941-011-00

E252-97940-005-00

E252-97940-015-00

E252-97940-005-00

E252-97923-001-00

E252-97923-002-00

E252-97923-003-00

E252-97923-004-00

E252-97933-000-00

E252-97933-003-00

E252-97933-002-00

E252-97927-001-00

E252-97937-001-00

E252-97928-000-00

E252-97938-000-00

E252-97927-000-00

E252-97937-000-00

E252-97920-000-00

E252-97930-000-00

E252-97927-003-00

E252-97937-003-00

E252-97928-001-00

E252-97928-003-00

D252-93577-018-00

D252-93577-018-00

D252-93648-032-00

D252-93648-032-00

D252-93648-036-00

D252-93648-036-00

D252-93648-178-00

D252-93648-196-00

D252-93577-022-00

D252-93577-024-00

D252-93648-180-00

D252-93648-192-00

D252-93648-180-00

D252-93648-014-00

D252-93648-016-00

D252-93648-018-00

D252-93648-020-00

D252-93648-100-00

D252-93648-106-00

D252-93648-104-00

D252-93648-070-00

D252-93648-158-00

D252-93648-076-00

D252-93648-164-00

D252-93648-068-00

D252-93648-156-00

D252-93648-004-00

D252-93648-094-00

D252-93648-074-00

D252-93648-162-00

D252-93648-078-00

D252-93648-082-00

ICN-A320-A-25XX1BPY-A-FAPE3-01GX5-A-003-01


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

Figure ICN-A320-A-25XX1BPY-A-FAPE3-01HYH-A-001-01 SHEET 5/5REV 00 Jun 13/19 A320-25-1BPYPart Number Roll Information

Page 205

CONF ALL

E252-94062-010-00 E252-94062-014-00

E252-94063-004-00 E252-94063-018-00

TOP OHSC 2FR E252-94063-008-00 E252-94063-022-00

TOP OHSC 2FR E252-94063-010-00 E252-94063-012-00

TOP OHSC 2FR

TOP OHSC 2FR

E252-94068-002-00 E252-94068-010-00TOP OHSC 1FC

E252-94068-006-00 E252-94068-014-00TOP OHSC 1FC

E252-94069-002-00 E252-94069-010-00TOP OHSC 1FC

E252-94069-006-00 E252-94069-014-00TOP OHSC 1FC

E252-94071-004-00 E252-94071-010-00TOP OHSC 1FPC

D252-93573-034-00

D252-93573-040-00

D252-93573-044-00

D252-93573-046-00

D252-93573-052-00

D252-93573-056-00

D252-93573-060-00

D252-93573-064-00

D252-93573-068-00

E252-94075-004-00 E252-94075-010-00TOP OHSC 2F

E252-94077-002-00 E252-94077-006-00TOP OHSC 3FM

E252-94086-002-00 E252-94086-008-00TOP OHSC 2FP

E252-94086-004-00 E252-94086-010-00TOP OHSC 2FP

E252-94088-002-00 E252-94088-010-00TOP OHSC 2F

E252-94088-006-00 E252-94088-014-00TOP OHSC 2F

E252-94089-002-00 E252-94089-006-00TOP OHSC 2F

D252-93573-074-00

D252-93573-080-00

D252-93573-082-00

D252-93573-084-00

D252-93573-086-00

D252-93573-088-00

D252-93573-090-00

D252-93647-158-00

D252-93647-164-00

D252-93647-166-00

D252-93647-168-00

D252-93647-172-00

D252-93647-174-00

D252-93647-178-00

D252-93647-180-00

D252-93647-182-00

D252-93647-186-00

D252-93647-190-00

D252-93647-192-00

D252-93647-194-00

D252-93647-196-00

D252-93647-198-00

D252-93577-004-00

PART NUMBER ROLL

OHSC NAMEAFTER SB25-1BPZBEFORE SB25-1BPZ TOP OHSC

PRE PN TOP OHSC PRE PNHOUSING

POST PNHOUSING

PRE PN TOP OHSC PLACARD PNTOP OHSCPOST PN

HOUSINGPLACARD PN

D252-93648-084-00E252-97908-001-00

E252-97918-003-00

E252-97918-005-00

E252-97918-001-00

E252-97900-012-00

E252-97900-002-00

E252-97910-013-00

E252-97910-003-00

E252-97910-000-00

E252-97912-006-00

E252-97915-011-00

E252-97932-006-00

E252-97932-007-00

E252-97902-001-00

E252-97902-003-00

E252-97912-003-00

E252-97928-004-00

E252-97938-001-00

E252-97938-002-00

E252-97938-005-00

E252-97901-001-00

E252-97901-000-00

E252-97911-003-00

E252-97911-002-00

E252-97911-000-00

E252-97930-001-00

E252-97935-002-00

E252-97942-000-00

E252-97942-001-00

E252-97920-001-00

E252-97920-003-00

E252-97930-002-00

D252-93648-166-00

D252-93648-168-00

D252-93648-172-00

D252-93648-002-00

D252-93648-000-00

D252-93648-092-00

D252-93648-090-00

D252-93648-086-00

D252-93648-096-00

D252-93648-150-00

D252-93577-028-00

D252-93577-030-00

D252-93648-006-00

D252-93648-010-00

D252-93648-098-00

ICN-A320-A-25XX1BPY-A-FAPE3-01HYH-A-001-01


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

REV 00 Jun 13/19 A320-25-1BPYPage 206

B. REPORTING SHEET

TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS -REVISE BIN BASE FOR PIVOTING OHSC

MODIFICATION No.: 162563K30846

(1) SB Reporting statusThis Service Bulletin will only be incorporated into affected customized Maintenanceand Flight Operations Products if it is duly reported to Airbus.

(2) GENERAL informationThe SB Reporting policy is published in ISI 00.00.00135. This document providesinformation regarding: the SB Reporting means and benefits, the update ofcustomized Maintenance Products and customized Flight Operations Products.If this Service Bulletin has an operational impact, refer to paragraph "Flight OperationsProducts" for further information on the update of affected Flight Operations Products.

(3) SB Reporting procedureStandard practice to report SB is to use the online reporting application onAirbusWorld.Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus, Question 2 "What arethe standard practices for SB Reporting?"

- If this SB requires previous or simultaneous accomplishment of other SBs,Question 3 "What about the reporting of prerequisite Service Bulletins?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.It is revised on a regular basis.


A318/A319/A320/A321SERVICE BULLETIN

APPENDIX

REV 00 Jun 13/19 A320-25-1BPYPage 207

C. QUALITY PERCEPTION FORMUse this form to tell us what is your perception of the quality of this Service Bulletin.The reported data that you provide us will be used to analyse areas of difficulties and totake corrective action to further improve the quality of our Service Bulletin.We thank you for the time you have taken in completing this form.

Quality rating of this SB 4 3 2 1Quality rating of the Accomplishment Instructions 4 3 2 1Quality rating of the Illustrations 4 3 2 1Is this SB easy to understand ? Y / N

NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score

If you have difficulties in the accomplishment of this SB please quote below the area(s) andgive a short description of the issue.

Planning Material InstructionsX Applicability X Tooling X PreparationX Reason X List of Materials

Operator SuppliedX Mod/Inspection

X Manpower X Kit content X TestX References X Re-identification X Close-upX Publication X IllustrationsX Industry Support

Comments :

Operator : Date :Name/TitlePlease return this form to :AIRBUS2, ROND POINT EMILE DEWOITINE31700 BLAGNACFRANCEOr via your Resident Customer Support Office.