A Presentation of the SPI-OSHA Alliance
description
Transcript of A Presentation of the SPI-OSHA Alliance
![Page 1: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/1.jpg)
The Society of the Plastics Industry, Inc.
Lockout/Tagout forThermoforming
Control of Hazardous Energy
A Presentation of the SPI-OSHA Alliance
![Page 2: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/2.jpg)
The Society of the Plastics Industry, Inc.
1910.147 The Control of Hazardous Energy a.k.a.
Lockout/Tagout (LOTO)
The specific practices and procedures necessary to disable machinery and equipment so that employees performing service and maintenance activities are protected
![Page 3: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/3.jpg)
The Society of the Plastics Industry, Inc.
The Purpose of LOTO
• Prevent injuries from the unexpected startup or release of stored energy
• Reduce the number of fatalities and injuries
• Establish a program and procedures for controlling hazardous energy
![Page 4: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/4.jpg)
The Society of the Plastics Industry, Inc.
Where to Begin?
• Job Safety Analysis (JSA)
• Develop Procedures
• Verify
• Train
• Audit
![Page 5: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/5.jpg)
The Society of the Plastics Industry, Inc.
Preventing Unexpected Startup or Release of Energy
Energy isolation:
• Minimize potential for inadvertent activation and/or release of stored energy
• Ensure power to the machine is isolated and locked at control points
• Use a method that cannot readily be removed, bypassed, overridden or otherwise defeated
![Page 6: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/6.jpg)
The Society of the Plastics Industry, Inc.
Common Types of Energy Used in Thermoforming
• Electrical• Mechanical• Hydraulic
• Pneumatic• Thermal• Gravity
![Page 7: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/7.jpg)
The Society of the Plastics Industry, Inc.
Definitions
• Servicing and/or maintenance - activities where employees may be exposed to unexpected start-up or release of hazardous energy including:– Construction– Installing and setting up– Adjusting, inspecting, modifying– Maintaining and/or servicing equipment– Lubricating, cleaning or unjamming– Tool changes or adjustments
![Page 8: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/8.jpg)
The Society of the Plastics Industry, Inc.
Definitions (cont’d)
• Set-up - Work to prepare a machine to perform its normal production operation
• Lockout – Placement of lockout device on an energy isolating device
• Lockout device – Device that uses a physical means to prevent energizing of a machine or equipment
![Page 9: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/9.jpg)
The Society of the Plastics Industry, Inc.
Definitions (cont’d)
• Energized - Connected to an energy source, or containing residual or stored energy
• Energy isolating device - A mechanical device that physically prevents the transmission or release of energy
Push buttons, selector switches and other control circuit devices are not energy isolating devices
![Page 10: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/10.jpg)
The Society of the Plastics Industry, Inc.
Common Causes of Accidents
• Failure to identify risk
• Employees working outside of job description
• Inadequate training and/or comprehension
• Pressure to meet production goals
• Feeling they can do the task after watching someone else do it
![Page 11: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/11.jpg)
The Society of the Plastics Industry, Inc.
LOTO applies when:• Employees are performing servicing and
maintenance, and there is a potential for injury from unexpected start-up or release of stored energy
• Service and maintenance that takes place during normal production, if employee:– Must remove or bypass a guard or safety
device; or – Must place any part of their body into the
danger zone
![Page 12: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/12.jpg)
The Society of the Plastics Industry, Inc.
Some Examples of when Lockout is Required
• Performing a set-up• Tool changing• Platen and toggle repair• Oven repair• While working on any electrical component• Repairs or maintenance on sheet transport
system• Major plastic jams
![Page 13: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/13.jpg)
The Society of the Plastics Industry, Inc.
Exception to LOTO
Minor servicing activities that take place during normal production when alternative effective protection is used
![Page 14: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/14.jpg)
The Society of the Plastics Industry, Inc.
Minor Servicing During Normal Production Operations
• Routine
• Repetitive
• Integral to the use of the equipment for production
![Page 15: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/15.jpg)
The Society of the Plastics Industry, Inc.
Alternative effective protection such as:
• Interlocked gates and barriers
• Mechanical blocks, pins, bars, or locking devices
• Remote lubricators or other remote devices
![Page 16: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/16.jpg)
The Society of the Plastics Industry, Inc.
Exceptions to LOTO While in Production Mode May Include:
• Unjamming parts in form or trim station
• Wear plate changes
• Polishing the mold
• Cutting die adjustmentsSharpening ShimmingStoning Notching
• Foam placement in cutting die
![Page 17: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/17.jpg)
The Society of the Plastics Industry, Inc.
• Prevents platens from closing when the mold is being set
• Must have at least one mechanical device on all Form Stations and all Trim Stations
Mechanical Safety Device
Metal Pin inserted into telescoping post to prevent travel of platens
![Page 18: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/18.jpg)
The Society of the Plastics Industry, Inc.
Mechanical Safety Device
Metal pin inserted to prevent any
travel of platens
![Page 19: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/19.jpg)
The Society of the Plastics Industry, Inc.
Mechanical Safety Device
Metal bar inserted to prevent any
travel of platens
![Page 20: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/20.jpg)
The Society of the Plastics Industry, Inc.
Form or Trim Station Pinning Device
Metal pin inserted to prevent any
movement of platen
Moveable platen
![Page 21: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/21.jpg)
The Society of the Plastics Industry, Inc.
Form or Trim Station Pinning Device
Metal pin inserted to prevent any
movement of platen
![Page 22: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/22.jpg)
The Society of the Plastics Industry, Inc.
Sanding Minor Mold Blemish
Metal pins inserted to prevent any
movement of platen
![Page 23: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/23.jpg)
The Society of the Plastics Industry, Inc.
Method of Blocking Oven Travel
![Page 24: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/24.jpg)
The Society of the Plastics Industry, Inc.
Accident #1Amputation of 3 fingers
• Product stuck in forming/cutting area of thermoforming machine
• Full-time press operator reached in to the unguarded machine to dislodge part
• Forming molds closed on his hand
• Surgeons were unable to reattach fingers
![Page 25: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/25.jpg)
The Society of the Plastics Industry, Inc.
Accident #2Amputation of fingers
• Employee was attempting to clear material which had become lodged in trim press
• Placed fingers into working envelope of the cutting die
• The cutting die cycled, trapping the employee’s fingers and thumb inside
• The employee’s fingers were severed and fell into a grinder located below the die
![Page 26: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/26.jpg)
The Society of the Plastics Industry, Inc.
Accident #3Amputation of 3 fingers and thumb
• Machine Operator was removing jammed parts from machine
• Inadvertently activated the remote switch which activated the die ram
• The die ram lowered and amputated 3 fingers and thumb
• Machine had been modified, side guards removed and micro switches taped down
![Page 27: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/27.jpg)
The Society of the Plastics Industry, Inc.
Accident #4Arm Caught in Machine
• Machine operator on ladder reached over plastic sheet on thermoformer and under the sheet guide to readjust the guide
• Glove got caught in the unguarded chain and sprocket drive
• Pulled arm into sprocket teeth and cycled
• After 1 cycle, arm was freed
![Page 28: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/28.jpg)
The Society of the Plastics Industry, Inc.
Accident #5Fatality
• Employee operating thermoforming machine on automatic mode
• Employee entered machine to make an adjustment
• Employee’s head caught in pinch point causing fatal crushing injury
![Page 29: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/29.jpg)
The Society of the Plastics Industry, Inc.
Core Components of an Energy Control Program
• Energy control procedures for each type of machine
• Training and retraining to ensure employees understand the program
• Periodic inspection to ensure procedures are being followed
ABC Co.Energy Control Program
Purpose._______________________________________________________________________
Compliance with this program ______________________________________________________________________________
Sequence of Lockout
(1)__________________________________________________
![Page 30: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/30.jpg)
The Society of the Plastics Industry, Inc.
Energy Control Procedures
• Must be specific to each type of machine and equipment you are working on
• Must include – Statement of intended use of the procedure – Steps for shutting down and securing machines
and equipment– Steps for placing, removing, and transferring of
lockout devices– Requirements for testing and verifying
effectiveness of lockout devices
![Page 31: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/31.jpg)
The Society of the Plastics Industry, Inc.
Required Training
• Authorized employees– Recognition of hazardous energy sources– Type and magnitude of energy in the workplace– Methods for energy isolation / control
• Affected employees– Purpose and use of energy control procedures
• Other employees in work area– Procedures related to restarting machines
![Page 32: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/32.jpg)
The Society of the Plastics Industry, Inc.
Retraining Requirements
Retraining is required if:• Change in job assignments• Change in machines• Change in energy control procedures• Equipment or processes present new hazards• Inspections reveal deficiencies in employee's
knowledge of energy control procedures• Retraining must reestablish employee
proficiency
![Page 33: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/33.jpg)
The Society of the Plastics Industry, Inc.
Periodic Inspections
• Performed at least annually
• Conducted by authorized employees
• Intended to correct inadequacies identified in program
• Certified
![Page 34: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/34.jpg)
The Society of the Plastics Industry, Inc.
Certification Requirements
• Identification of equipment or machinery
• Date of inspection
• Names of employees involved in the inspection
• Name of person(s) performing inspection
![Page 35: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/35.jpg)
The Society of the Plastics Industry, Inc.
Application of the Energy Control Procedure (Lockout)
1. Prepare for shutdown2. Shut down equipment3. Isolate all energy sources4. Apply locks & tags5. Release stored energy6. Verify equipment isolation7. Perform the task 8. Release from Lockout
![Page 36: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/36.jpg)
The Society of the Plastics Industry, Inc.
Step 1: Prepare for Shutdown
• Understand equipment hazards
• Notify other workers of shutdown
![Page 37: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/37.jpg)
The Society of the Plastics Industry, Inc.
Step 2: Shut down equipment
• Use the normal shutdown procedures
• Turn all switches to OFF/Neutral
![Page 38: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/38.jpg)
The Society of the Plastics Industry, Inc.
Step 3: Isolate all Energy Sources
• Use energy isolation devices in accordance with established procedures to prevent transmission or release of energy
![Page 39: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/39.jpg)
The Society of the Plastics Industry, Inc.
Step 4: Apply Locks & Tags
Apply locks and tags to:
• Valves
• Breakers/electrical disconnects
• Mechanical blocksValve lockout device
![Page 40: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/40.jpg)
The Society of the Plastics Industry, Inc.
Step 5: Release or Block all Stored Energy
• Discharge capacitors• Block/disconnect
lines• Block or release
springs• Block elevated parts• Relieve system
pressure
• Drain fluids• Vent gases• Allow system to cool
(or use PPE)• Apply any additional
locks and tags needed
![Page 41: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/41.jpg)
The Society of the Plastics Industry, Inc.
Step 6: Verify Equipment Isolation• Check that other workers
are clear of potential hazards
• Check that locking devices are secure
• Attempt normal startup
• Return control to OFF/Neutral
Controls to verifyenergy isolation
![Page 42: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/42.jpg)
The Society of the Plastics Industry, Inc.
Step 7: Perform the Task
![Page 43: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/43.jpg)
The Society of the Plastics Industry, Inc.
Step 8: Release from Lockout
• Ensure machinery is properly assembled and all tools removed
• Ensure that employees are outside of danger zones and are notified that devices are being removed
• Remove LOTO devices– Must be removed by authorized employee
who applied it
![Page 44: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/44.jpg)
The Society of the Plastics Industry, Inc.
The Job Safety Analysis Process
The Job Safety Analysis (JSA) process is a very effective means of helping reduce incidents, accidents, and injuries in the workplace. It is a multi-step process.
•Basic Job Steps
•Potential Hazards
•Recommended Safe Job Procedures
![Page 45: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/45.jpg)
The Society of the Plastics Industry, Inc.
Our sincere thanks to:• SPI Thermoforming Institute
– Buckell Plastic Co., Inc.– Prent Corporation– Placon Corporation
• United Southern Industries, Inc. • OSHA Regions V & VIII• Michigan OSHA• OSHA’s Office of Education and Training• OSHA’s Salt Lake Technical Center • The Society of the Plastics Industry, Inc.
![Page 46: A Presentation of the SPI-OSHA Alliance](https://reader036.fdocuments.us/reader036/viewer/2022062400/56814c37550346895db93de2/html5/thumbnails/46.jpg)
The Society of the Plastics Industry, Inc.
Do You Have AnyQuestions?