A Panalog Pa Systems
-
Upload
joeannamarydeguzman -
Category
Documents
-
view
213 -
download
0
Transcript of A Panalog Pa Systems
-
7/30/2019 A Panalog Pa Systems
1/11
70W MIXER AMPLIFIER
360W POWER AMPLIFIER
1000W POWER AMPLIFIER
1500W POWER AMPLIFIER
460W POWER AMPLIFIER
660W POWER AMPLIFIER
130W MIXER AMPLIFIER
260W MIXER AMPLIFIER
360W MIXER AMPLIFIER
AP-811P
AP-130MAP-260MAP-360M
AP-70M
AP-8360AP-8460
AP-8660
AP-1000AAP-1500A
9-INPUT MIXER PRE-AMPLIFIER
AP-812M 10-CHANNEL MONITOR PANEL
AP-815E EMERGENCY PANEL
AP-813A 16-ZONE SPEAKER SELECTOR
AP-813B 2 X 5-ZONE SPEAKER SELECTOR
AP-813D 10-ZONE SPEAKER SELECTOR
AP-SERIES BASIC PA SYSTEM
9
70W MIXER AMPLIFIERAP-200P
130W MIXER AMPLIFIERAP-300P
260W MIXER AMPLIFIERAP-600P
360W MIXER AMPLIFIERAP-1000P
-
7/30/2019 A Panalog Pa Systems
2/11
AP-200P
AP-600P
Highly flexible mixer amplifiers for a wide
variety of voice and background music a-
pplications such as retail shops, restaura-
nts and bars, service centers, houses of
worship, warehouses and many more. M-
ain features are
Cost Effective Mixer Amp
5-INPUT MIXER AMPLIFIERS
AP-300P
AP-1000P
REAR PANEL
SPECIFICATIONS AP-600P AP-1000PAP-200P AP-300P
Rated Power Output
Output Regulation
Speaker Output
Input
Output
THD
Frequency Response
Tone Controls
S/N Ratio
Controls
Cooling
Indicators
Power Consumption
Protection
Power Requirments
Dimensions
Built-in Dimensions
Carton Dimensions
Net Weight
Finish
Gross Weight
70W
Less than 3 dB (no load to full load)
70 ohms (70V)
Low impedance: 4-16 ohms
MIC 1, 2, 3:600 ohms, 5mV, unbalanced, phone jack; AUX 1, 2: 10k ohms, 470mV, unbalanced, RCA jack
600 ohms, >650mV, RCA jack
60 - 15,000 Hz, +/- 3dB
Less than 0.5% at 1kHz (1/3 Rated Power)
Better than 73dB
BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB)
5 input gain, 1 treble, 1 bass, 1 mute, and power switch
Internal 12VDC fan, extensive heat sinking
Power indicator LED, LED output level meter 0, 2, 4, 6, 8, 10dB
AC Fuse: 4A
140W
220-240V AC, 50/60 Hz
89(H) x 483(W) x 366(D) mm
2 U rack 19 inch
185(H) x 520(W) x 435(D) mm
10.04kg
11.72kg
Panel: steel plate, black
130W
260W
11.36kg
13.02kg
260W 360W
350W 485W
13.68kg 14.08kg
15.32kg 15.70kg
Current limiter, short circuit and thermal protection circuits
AC Fuse: 6A AC Fuse: 8A AC Fuse: 8A
Case: steel plate, black
143 ohms (100V)
38 ohms (70V)
Low impedance: 4-16 ohms
77 ohms (100V)
19 ohms (70V) 14 ohms (70V)
Low impedance: 4-16 ohms Low impedance: 4-16 ohms
39 ohms (100V) 28 ohms (100V)
3 microphone and 2 auxiliary inputs
Individual input gain controls with mastervolume control
1 line output
Bass and treble tone controls
100V, 70V and 4-16 Ohms transformer-isolated speaker outputs
LED level meter
Automatic mute function for paging andannouncements
Speaker output short circuit protection
AP SERIES
0
-
7/30/2019 A Panalog Pa Systems
3/11
AP-70M
AP-260M
Highly flexible mixer amplifiers for a widevariety of voice and background music a-
pplications such as retail shops, restaura-
nts and bars, service centers, houses of
worship, warehouses and many more. M-
ain features are
AP Mixer Amp Series
5-INPUT MIXER AMPLIFIERS
AP-130M
AP-360M
REAR PANEL
SPECIFICATIONS AP-260M AP-360MAP-70M AP-130M
Rated Power Output
Output Regulation
Speaker Output
Input
Output
THD
Frequency Response
Tone Controls
S/N Ratio
Controls
Cooling
Indicators
Power Consumption
Protection
Power Requirments
Dimensions
Built-in Dimensions
Carton Dimensions
Net Weight
Finish
Gross Weight
70W
Less than 3 dB (no load to full load)
70 ohms (70V)
Low impedance: 4-16 ohms
MIC 1, 2, 3:600 ohms, 5mV, unbalanced, phone jack; AUX 1, 2: 10k ohms, 470mV, unbalanced, RCA jack
600 ohms, >650mV, RCA jack
60 - 15,000 Hz, +/- 3dB
Less than 0.5% at 1kHz (1/3 Rated Power)
Better than 73dB
BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB)
5 input gain, 1 treble, 1 bass, 1 mute, and power switch
Internal 12VDC fan, extensive heat sinking
Power indicator LED, LED output level meter 0, 2, 4, 6, 8, 10dB
AC Fuse: 4A
140W
110-120V or 220-240V AC, 50/60 Hz
89(H) x 483(W) x 366(D) mm
2 U rack 19 inch
185(H) x 520(W) x 435(D) mm
10.04kg
11.72kg
Panel: steel plate, black
130W
260W
11.36kg
13.02kg
260W 360W
350W 485W
13.68kg 14.08kg
15.32kg 15.70kg
Current limiter, short circuit and thermal protection circuits
AC Fuse: 6A AC Fuse: 8A AC Fuse: 8A
24V DC 24V DC
Case: steel plate, black
143 ohms (100V)
38 ohms (70V)
Low impedance: 4-16 ohms
77 ohms (100V)
19 ohms (70V) 14 ohms (70V)
Low impedance: 4-16 ohms Low impedance: 4-16 ohms
39 ohms (100V) 28 ohms (100V)
3 microphone and 2 auxiliary inputs
Individual input gain controls with mastervolume control
1 line output
Bass and treble tone controls
100V, 70V and 4-16 Ohms transformer-isolated speaker outputs
LED level meter
Automatic mute function for paging andannouncements
Speaker output short circuit protection
AP SERIES
11
-
7/30/2019 A Panalog Pa Systems
4/11
The AP-811P is a versatile mixer pre-amplifier
with 4 microphone inputs, 3 auxiliary inputs, 2
emergency inputs (high priority) and mutefunction.
MIC1, EMC1, EMC2 are priority inputs,
automatically muting all other signal inputs. MIC1
has the highest priority, able to suppress all other
inputs.
Output from the AP-815E emergency panel to
EMC1 provides for alarm siren or emergency
announcement to be broadcast over the public
address system
REAR PANEL
AP-811P
AP-811P
AP-815E
AP-F508R
AP-8360
9-INPUT MIXER PRE-AMPLIFIER
AM/FM TUNER
EMERGENCY PANEL
CD PLAYER
MIC 1
MIC 1
MIC 2
MIC 3
SPEAKERS
SPEAKERS
DUAL CASSETTE DECK
POWER AMPLIFIER
9 inputs, 2 outputs
Automatic mute function for pagingand announcements
Individual input gain controls withmaster volume control
Bass and treble tone controls
SPECIFICATIONS AP-811P
AP SERIES
Input
MIC 1, 2, 3, 4:600 ohms, 5mV, unbalanced, phone jackAUX 1, 2, 3: 10k ohms, 200mV, unbalanced, RCA jack
EMC 1, 2: 10k ohms, 200mV, unbalanced, phone jack
Output
Frequency Response
S/N Ratio
Power Requirements
Dimensions
600 ohms, 775mV, 0 dB, RCA jack
60Hz - 15kHz (+/- 3dB)
Better than 70dB
THD Less than 0.1% at 1kHz
Tone Controls
Muting Function
BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB)
MIC1 overrides other input signals with 0~30 dB attenuationEMC1 overrides other input signals except MIC 1
110-120V or 220-240V AC, 50/60 Hz; 24VDC
89(H) x 483(W) x 366(D) mm
2
-
7/30/2019 A Panalog Pa Systems
5/11
AP-8360These commercial-grade power amplifiersefficiently deliver up to 660 watts of clean,
reliable audio for the most demanding public
address applications.
Rugged and over-built to give years of
dependable service, they are equipped with
massive torrodial power transformers,
extensive heat-sinking and fan cooling,
protective circuits such as over-temperature,
short circuit, RFI and soft start.
AP Power Amp Series
SINGLE CHANNEL POWER AMPLIFIERS
AP-8460
AP-8660
REAR PANEL
SPECIFICATIONS AP-8660AP-8360 AP-8460
Rated Power Output
Output Regulation
Speaker Output
Input
Output
THD
Frequency Response
Slew Rate
S/N Ratio
Controls
Cooling
Indicators
Power Consumption
Protection
Power Requirments
Dimensions
Built-in Dimensions
Carton Dimensions
Net Weight
Finish
Gross Weight
360W
Less than 3 dB (no load to full load)
13.6 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
Less than 1V, unbalanced, XLR and phone jack
775V, 0dB, XLR and phone jack
60 - 16,000 Hz, +/- 3dB
Less than 0.5% at 1kHz (1/3 Rated Power)
Better than 73dB
15V/uS
Volume control and power switch
Internal 12VDC fan, extensive heat sinking
Power, Clip, S ignal, Protect, and Temp LEDs
AC Fuse: 10A
485W
110-120V or 220-240V AC, 50/60 Hz
89(H) x 483(W) x 366(D) mm
2 U rack 19 inch
185(H) x 520(W) x 435(D) mm
15.12kg
16.76kg
Panel: steel plate, black
460W
620W
110-120V or 220-240V AC, 50/60 Hz
17.66kg
19.30kg
660W
880W
110-120V or 220-240V AC, 50/60 Hz
20.8kg
22.3kg
Current limiter, short circuit and thermal protection circuits
AC Fuse: 12A AC Fuse: 15A
24V DC
Case: steel plate, black
27.8 ohms (100V), balanced
10.7 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
21.7 ohms (100V), balanced
7.4 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
15.1 ohms (100V), balanced
100V, 70V and 4-16 Ohms transformer-isolated speaker outputs
Combination XLR/RCA Line In and LineOut connectors
LED status indicators
Speaker output short circuit protection
AP SERIES
13
-
7/30/2019 A Panalog Pa Systems
6/11
AP-1000A All the great features of the AP power ampseries but when even more power is
required, these AP -series high power amps
provide up to 1500 watts into low impedance
or 70/100V constant voltage speaker loads.
AP High Power Amps
SINGLE CHANNEL POWER AMPLIFIERS
AP-1500A
SPECIFICATIONS AP-1500AAP-1000A
Rated Power Output
Output Regulation
Speaker Output
Input
Output
THD
Frequency Response
Slew Rate
S/N Ratio
Controls
Cooling
Indicators
Power Consumption
Protection
Power Requirments
Dimensions
Built-in Dimensions
Carton Dimensions
Net Weight
Finish
Gross Weight
1000W
1350W
110-120V or 220-240V AC, 50/60 Hz
133(H) x 483(W) x 366(D) mm
3 U rack 19 inch
185(H) x 520(W) x 435(D) mm
25.0kg
27.5kg
1500W
2000W
27.0kg
30.0kg
Less than 3 dB (no load to full load)
Current limiter, short circuit and thermal protection circuits
AC Fuse: 20A
Panel: steel plate, black
Case: steel plate, black
Less than 1V, unbalanced, XLR and phone jack
775V, 0dB, XLR and phone jack
Less than 0.5% at 1kHz (1/3 Rated Power)
Better than 105dB
40V/uS
Volume control and power switch
Power, Clip, Signal, Protect, and Temp LEDs
Internal 12VDC fan, extensive heat sinking
4.9 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
10.0 ohms (100V), balanced
3.3 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
6.7 ohms (100V), balanced
50 - 18,000 Hz, +/- 1.5dB
REAR PANEL
100V, 70V and 4-16 Ohms transformer-isolated speaker outputs
Combination XLR/RCA Line In and Line
Out connectors
LED status indicators: power, clip, signal,protect and high temperature
Speaker output short circuit protection
AP SERIES
4
-
7/30/2019 A Panalog Pa Systems
7/11
These commercial-grade power amplifiersefficiently deliver up to 360 watts of clean,reliable audio for the most demanding publicaddress and voice alarm applications.
Rugged and over-built to give years ofdependable service, they are equipped withmassive torrodial power transformers,extensive heat-sinking and fan cooling,protective circuits such as over-temperature,
AP Power Amp Series
SINGLE CHANNEL POWER AMPLIFIERS
Rear Panel
SPECIFICATIONS AP-8360IAP-8260I
Rated Power Output
Output Regulation
Speaker Output
Input
Output
THD
Frequency Response
Slew Rate
S/N Ratio
Controls
Cooling
Indicators
Power Consumption
Protection
Power Requirments
Dimensions
Built-in Dimensions
Carton Dimensions
Net Weight
Finish
Gross Weight
360W
Less than 3 dB ( )From no signal to full working situatio
13.6 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
Less than 1V, unbalanced, XLR and phone jack
775V, 0dB, XLR and phone jack
60 - 16,000 Hz, +/- 3dB
15V/uS
AC Fuse: 10A
720W
110-120V or 220-240V AC, 50/60 Hz
89(H) x 483(W) x 366(D) mm
2 U rack 19 inch
185(H) x 520(W) x 435(D) mm
18.6kg
20.1kgPanel: steel plate, black
260W
520W
15.6kg
17.1kg
AC Fuse: 8A
24V DC
Case: steel plate, black
27.8 ohms (100V), balanced
10.7 ohms (70V), balanced
Low impedance: 4-16 ohms, balanced
21.7 ohms (100V), balanced
100V, 70V and 4-16 Ohms transformer-isolated speaker outputs
Additional features than normal amp:
Combination XLR/RCA Line In and LineOut connectors
LED indicator in front and dry contactin rear panel for amplifier fault monitor
LED indicator in front and dry contactin rear panel for AC fault monitor
LED indicator in front and dry contactin rear panel for DC fault monitor
Speaker output short circuit protection
AP SERIES
Less than 1V, unbalanced, XLR and phone jack
775V, 0dB, XLR and phone jack
60 - 16,000 Hz, +/- 3dB
Less than 0.5% at 1kHz (1/3 Rated Power)
>70 dB>70 dB
15V/uS
Volume control and power switch
Internal 12VDC fan, extensive heat sinking
Power, Clip, S ignal, Protect, and Temp LEDs
AC FUSE1, Short circuit, high temperature , over voltage protection
Panel: steel plate, black
Case: steel plate, black
89(H) 483(W) 366( D) mm
2 U rack 19 inch
185(H) 520(W) 435(D) mm
Pin 1,2AC Fault
Pin 2,4DC Fault
Pin 5,6AMP Fault
Front Panel
AP-8260I260W AMPLIFIER
VOLUME5
0
1
2
3
4 6
7
8
9
10
POWER 2 4 6 8
R
Amplifier DC AC
OKOKOK
AMP
DC
AC
15
ok ok ok
short circuit, RFI and soft start.
-
7/30/2019 A Panalog Pa Systems
8/11
8 SPEAKER
8 SPEAKER
8 SPEAKER 8 SPEAKER
8 SPEAKER 8 SPEAKER
8 SPEAKER
8 SPEAKER 8 SPEAKER
SINGLE SPEAKER - SPEAKER LOAD=8 OHMS
LOW IMPEDANCE (CONSTANT IMPEDANCE) - 4-16 OHMS
HIGH IMPEDANCE (CONSTANT VOLTAGE) 70/100V
FOUR SPEAKERS IN SERIES/PARALLEL - SPEAKER LOAD=8 OHMS
70V - SPEAKER LOAD=80% AMPLIFIER Rated Power
100V - SPEAKER LOAD=80% AMPLIFIER Rated Power
TWO SPEAKERS IN PARALLEL - SPEAKER LOAD=4 OHMS
TWO SPEAKERS IN SERIES - SPEAKER LOAD=16 OHMS
70V SPEAKER70V SPEAKER
100V SPEAKER 100V SPEAKER
Amplifier/Speaker Connections
AP SERIES
6
-
7/30/2019 A Panalog Pa Systems
9/11
Monitor up to 10 speaker channels audibly by using the built-in
loudspeaker. 5-LED dB level meter visually indicates the chann-
els signal level
10-CHANNEL MONITOR PANEL
AP-812M
POWER AMPLIFIER
SPEAKER SELECTOR
MIXER PRE-AMPLIFIERRECORDING MIC
POWER AMPLIFIER
AP-812M
AP-813D
AP-8660
AP-815E
AP-811P
AP-8660
SPECIFICATIONS AP-812M
Input Input
Monitored Channels Output
Audible Monitor Frequency Response
Visual Monitor THD
Indicators Controls
Controls ADC/DAC
Power Consumption Power Consumption
Protection Protection
Power Requirements Power Requirements
Net Weight Net Weight
Gross Weight Gross Weight
FinishFinish
70/100V audio signal MIC:
-
7/30/2019 A Panalog Pa Systems
10/11
16-Zone 2 x 5-Zone 10-Zone Speaker Selector
AP-813A
AP-813B
AP-813D
Flexible multi-input speaker selector arranged
in a 4 x 4 matrix with priority override. 16
speaker zones are divided into 4 groups, each
group can have a separate audio source. A
priority bus is provided to mute background
music for zone paging and emergency alarms
With 2 amplifier inputs and 2 groups of speaker
outputs, the AP-813B can be used as two 5-zone
speaker selectors with separate audio sources or
as a 10-zone selector with a single audio source
The AP-813D is an essential component for a
public address system. It has two amplifierinputs (A and B) and controls up to ten speaker
zones. It has the ability to select zones when
receiving an alarm signal to switch from Input
A (background music signal) to Input B (alarm
sound signal) to the corresponding zones
automatically
AP Speaker Selectors
16-ZONE SPEAKER SELECTOR
2 X 5-ZONE SPEAKER SELECTOR
10-ZONE SPEAKER SELECTOR
Use as two 5-zone selectors or asone 10-zone selector
10-channel priority bus
Support for up to 4 audio sources
2 alarm activation outputs
16-channel priority bus
Supports up to two audio sources
REAR PANEL
REAR PANEL
REAR PANEL
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
AP-813A
AP-813B
AP-813D
Input
Input
Input
Speaker Output
Speaker Output
Speaker Output
4 program and 1 priority channels, 70/100V audio signal
2 program channels, 70/100V audio signal
1 program and 1 priority channels, 70/100V audio signal
4 groups of 4 zones, 70/100V audio signal
2 groups of 5 zones, 70/100V audio signal
1 group of 10 zones, 70/100V audio signal
Priority Bus
Priority Bus
Priority Bus
Power Handling
Power Handling
Power Handling
16 channels, activated by 0V signal
N/A
10 channels, activated by 0V signal
1.5kW total capacity, 375W per channel
1.5kW total capacity, 150W per zone
1.5kW total capacity, 150W per zone
Alarm Output
Alarm Output
Alarm Output
Controls
Controls
Controls
0V signal
N/A
0V signal
16 pushbutton zone selectors, 1 power switch
10 pushbutton zone selectors, 1 power switch
10 pushbutton zone selectors, 1 power switch
Power Requirements
Power Requirements
Power Requirements
Dimensions
Dimensions
Dimensions
110-120V or 220-240V AC, 50/60 Hz; 24VDC
110-120V or 220-240V AC, 50/60 Hz; 24VDC
110-120V or 220-240V AC, 50/60 Hz; 24VDC
89(H) x 483(W) x 366(D) mm
89(H) x 483(W) x 366(D) mm
89(H) x 483(W) x 366(D) mm
AP SERIES
8
-
7/30/2019 A Panalog Pa Systems
11/11
AP-813A
AP-813B
AP-813D
AP-813A AP-813B AP-813D Examples
ZONES 1-4
ZONES 1-5
ZONE 1
ZONES 5-8
ZONES 6-10
ZONE 10
ZONES 9-12 ZONES 13-16
AP-813A
AP-CD12
AP-CD12
AP-CD12AP-812M
AP-815E
AP-70M
AP-130M
AP-260M
AP-130M
AP-811P AP-812M
AP-360M
AP-8660
AP-8460
AP-8660
AP-815E
AP-360M
AP-F508R
AP-F508R
AP-F508R
AP-W228K
AP-W228K
AP-813D
AP-813B
MIC 1
MIC 1
MIC 1
MIC 1
MIC 1
MIC 1
MIC 1
AM/FM TUNER
AM/FM TUNER
MONITOR PANEL
MONITOR PANEL
AM/FM TUNER
CD PLAYER
PROGRAM
PROGRAM A
PROGRAM B
PROGRAM
PRIORITY
ABCD
A
B
B
A
E
PRIORITY
CD PLAYER
CASSETTE DECK
CASSETTE DECK
EMERGENCY PANEL
EMERGENCY PANEL
POWER AMPLIFIER
POWER AMPLIFIER
POWER AMPLIFIER
CD PLAYER
MIXER PRE-AMPLIFIER
MIXER AMPLIFIER
MIXER AMPLIFIER
MIXER AMPLIFIER
MIXER AMPLIFIER
MIXER AMPLIFIER
MIXER AMPLIFIER
AP SERIES
19