A New Paddle for a New Extra • AmateurRadio
Transcript of A New Paddle for a New Extra • AmateurRadio
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
1/16
AmateurRadio.com
International Ham Radio News & Opinion
NEW! Ham Radio Equipment For Sale:
Wouxun KG-UV8D
$109.99
Wouxun KG-UV920P
$259.99
Baofeng UV-5R
$29.99
Ham Starter Kit
$349.99
Home
A New Paddle for a New Extra
14 May 2016 | by Greg KK4TIX | Share | Tweet | Leave a Comment (1)
Since my last article was
published, I made my fourth attempt to pass the extra exam. I knew I had done better, but was pleasantly surprised when
the VEs congratulated me. I’m still trying to believe that since it was only one week ago. Never mind that anyway, it
doesn’t really have anything to do with the new CW paddle I made.
Way back when, after I had been on the air for a few months, I decided I’d give CW a shot. I knew I’d need a key or
paddle, but didn’t really know where to start. A simple Internet search for CW paddle brought up a very large number of
beautiful paddles that nearly made me drool. What prevented the drooling was the price attached to nearly all of those
lovely paddles. I wasn’t about to spend that kind of money on something that I didn’t even know I could operate.
My next Internet search included the word “homebrew” to see if it were even possible to make a CW paddle that would
work. Much to my amazement, there are hundreds of different designs for homebrew CW paddles. Altoid tins, hacksaw
blades, plastic, wood, all wire, metal, you name it, someone had created one. Seeing all of those wonderful homemade
paddles, I knew it was possible, but was it possible for me?
I thought I’d try one with a hacksaw blade. I had some scrap wood around and then discovered I only had one hacksaw
blade, and that was attached to my only hacksaw. So, that was out. I searched around my messy garage and finally came
across a piece of aluminum I had used for landing gear strut for one of my RC planes. This was left over from that
landing gear project. It was fairly soft and somewhat flexible. It wasn’t huge, only 0.1” by 1”. Perfect, I thought.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
2/16
I set out searching for a base material to mount the thing on. I had 5/8” plywood, but nothing easily workable. Further
searching I realized I had a “super duty” paint stick from ACE hardware. (Again from one of my RC planes). Yup. That
would do it. One small piece of 5/8” plywood and about half a “super duty” paint stick, that aluminum, some small
hardware, scrap 22 gauge wire, and a “stereo” RCA connector cable.
Viola.
Sure, it isn’t much to
look at, but it worked. Getting on the air with it was another story. (The WA9AS… was me trying to figure out who my
first 6 meter QSO was, again, another story…)
Nonetheless, it served me well for all two of my CW QSOs to date. Even though I only had the two QSOs, I still called
CQ fairly regularly, just for practice if nothing else. This was great for several months. Then, just a couple of weeks ago,
the dah kept being delayed, which messed up my letters tremendously. Sometimes I’d key out my dah-dit-dah dah-dit-dah
dit-dit-dit-dit dah. As many know, that would have been received as, KKH T, which, of course made no sense. I imagine
anyone listening would have been seriously confused as they heard, CQ N NQ CQ, KKH T, N T, KK4 TID T. It nearly
made me angry and I gave up trying. I knew it was time for a new paddle.
Behold, the quest for a new paddle begins…
The best thing was, I still had another piece of that aluminum left. It was about 7.5” long. Not too shabby for a new CW
paddle. I tossed around the idea of using more paint sticks, but I was less than satisfied with the weight of that first
paddle. I always had to hold the paddle down with my left hand while keying with my right. I’m a left handed writer, so,
that made it impossible to write anything quickly if the sending station was quick on the draw. With that in mind, I set out
to make a paddle that was a little weightier.
It wasn’t long before I realized I had plenty of 2×4 lying around. It would be made from a 2×4, or two pieces of 2×4.
Although I had that idea and thought it would be easy, I was mistaken, a little. I thought I’d cut one piece for the base and
set a second piece of 2×4 on top. But that didn’t happen.
First I measured out 4.5 inches for the length of the base.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
3/16
That was easy, until I cut
it. Turns out, the bottom had a chunk taken out of it. So I cut a second piece at 4.5 inches. This one had a knot in it. Third
time is the charm, at least in this case. I had videoed the making of this, but the quality turned out so bad, I don’t have an
initial picture.
After that initial piece, it was time for the “top” piece. I measured and measured until I finally came up with the height of
1.75 inches. That would make the whole thing, 3.2 inches tall. After thinking about that, it seemed a bit too tall for its
size. I also then realized that my initial idea, to have that second piece stand vertically, wouldn’t work because I would be
cutting a slot in it to mount the aluminum paddle. More measuring and more measuring came up with cutting a piece 3.5
inches long to lay sideways. Well, there now the thing was going to be over 4 inches tall. That’s outrageous.
The next evolution was to cut that 3.5 inch piece of 2×4 down so it wasn’t so tall. 2.9 inches turned out to be the magic
number for me. It allowed me to slot it for the aluminum piece. I set the blade depth just deeper than the one inch for the
aluminum, then cut the slot in the side of the 2×4.
I set it on another piece
of 2×4 to provide a safe barrier when I ran that piece through. Thankfully that worked wonderfully for me.
As it turned out, I didn’t get it deep enough, but was afraid to take off more so I ended up slotting the base for the
aluminum as well. That all turned out like this:
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
4/16
Next was to attach the
back to the base. That was done by gluing then screwing the pieces together. After the glue dried, I took out the screws.
With those together, it was time to work on the wiring. I cut up an RCA splitter to make each side of the paddle. I split the
shield from each wire, one red, one white. I extended those center conductor with the same color. I then tied the shields to
a black wire for each lead.
There is shrink tube
between each connection and then over that shrink tube. The two black wires, the shields will be connected together for
one lead.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
5/16
I now have all the wiring
necessary. I’ll use the black wire to attach to the paddle itself, and then have a special treat to get the red and white wire
in place. But first, there is some prep work to be done. Here I drill a couple of holes for the posts that will be placed.
Looking closely, you
might see the hole in the paddle as well. All should be in perfect, or near perfect alignment. The distance from the end
was pretty arbitrary, but ended up being 1 inch from the end of the base, and 2 inches from the end of the paddle. I open
the holes for the posts to just undersized for the screws I intend to use, so I can screw them in. They turned out to be 1.5
inch long #8 machine screws. That’s a #6 threaded rod for the pointer thing. (No I don’t know what these parts are
supposed be called.)
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
6/16
Yes, the threaded rod is
too long. But I’ll fix that later. Here I put the hole in the tail to accept the ground wire.
That’s a #6 screw, far too
long, but I used it anyway. Next up, I’ll open up the post holes on the bottom to accept a nut. I made a number of small
drill depths to get that nut up far enough to engage the screw from the top. I didn’t want a bunch of the screw poking
through, so I carefully advanced the drill until it was the right depth. I also took this opportunity to use my Dremel to cut
a creative path for my wiring on the bottom.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
7/16
The straight cuts were
made with the table saw. The fancy M shape was made with the Dremel. You can see the ends of the red and white wire
are already stripped and soldered. I have the red and white wires just long enough to stick in the bottom of the holes on
the nut side. I’ll simply pinch the wires with the nut when I tighten everything down.
Next up, I take everything off except the paddle itself and add a coat of stain, after much sanding, of course. I also
sprayed several layers of polyurethane over everything, yes everything. I tested out the paddle to make sure it wouldn’t
provide any resistance.
Now it is time to startassembling everything. First the post and pointer thing.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
8/16
I set the height of the
screw so that the nut, jammed up to the top, could serve as the contact point for the pointer thing. With the screw at the
bottom of the smaller hole, I ran the wire and nut up and held it in place while I screwed the screw down to meet it. Once
the screw had one thread poking through the nut, I tightened the jam nut located on the wood in the above picture.
Here’s a bottom view of the wires and one nut. It is hard to see where the wire is pinched between the nut and the wood.
Before I added the
second post screw, I estimated the length needed for the center pointer thing to be, cut it, then cut it again, and again.
Finally, I got the length right. I thought.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
9/16
The tolerance there was
super tight. Almost imperceptible movements provided enough movement to activate the tone. It is nearly complete.
Here’s a closer look at where one wire connects to the post screw.
To secure the wires to
the bottom, I considered tape, then not tape. I don’t have a perfectly smooth bottom for tape to stick, plus I didn’t want all
that stickiness if I ever needed to take it off. Going back to my RC stuff, I broke out the hot glue gun, and put a few beads
here and there. They are tough to see, but here’s the picture.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
6
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
10/16
You can see the black
ground wire feeding up to the cut that was made for the aluminum paddle. I stripped about an inch off the end of that,
shaped it into a loop, and soldered it to itself to make a solid connection for the screw in the back of the paddle. Also, the
holes left by the screws can be seen.
Now it is all done.
Almost.
It’s time for testing anyway. So I plugged it in to my RCA to stereo adapter and into the back of the TS-2000. It worked
like a charm. For a day. No, I didn’t send out anything, just practiced with it. The next day, I found the dah stuck solidly. Icouldn’t push it over to hit the dit or stop the dah. This meant something had changed. I suppose using wood, I should
have expected that.
Nonetheless, I took things apart and cut that center pointer thing down a little more. Now there is definite movement, but
not an excessive amount. It was a challenge to try to show the gap between the center pointer thing and the post screw.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
11/16
All that is left now is to
put some feet on it.
I opted for stick-on foam
rubber ones, so I could peel them off if needed.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
12/16
All dressed up and no
place to go…
Thanks for reading.
As it turns out, that thing still isn’t heavy enough to keep from moving around when I key. So I’m going to get some
fishing weights, drill holes for them and hot glue them on the bottom.
All I need now is my third CW QSO!
Greg Walters, KK4TIX, is a special contributor to AmateurRadio.com and writes from Kentucky, USA.
One Response to “A New Paddle for a New Extra”
Colin GM4JPZ:
14 May 2016 at 21:38 UTC
Thanks for the detailed description, Greg. You can be proud of your handiwork there. Pity condx are so poor at the
moment, otherwise I would be happy to join in your 3rd CW QSO.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
13/16
Just one little point: It’s normal to pronounce the dot in the middle of a character (anywhere but the end in fact) as
DI, leaving DIT for the end. An example DI DAH DI DIT, DAH DI DAH DIT etc. Your hand sent CW should
correspond to this and the rhythm will sound right.
Good luck with your CW and 73 from GM-Land!
Colin
Leave a Comment
Name & Callsign (required)
E-Mail (will not be published) (required)
Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter
News, Opinion, Giveaways & More!
E-mailJoin over 3,000 subscribers!
We never share your e-mail address.
Also available via RSS feed, Twitter, and Facebook .
UPDATED Ham Radio Equipment For Sale: Alinco | Ameritron | Astron | Baofeng | Collins | Drake | Elecraft | Heathkit |
Icom | Kenwood | MFJ | Motorola | Swan | Ten-Tec | Vibroplex | Wouxun | Yaesu
Subscribe FREE to AmateurRadio.com's
Amateur Radio Newsletter
We never share your e-mail address.
Please support our generous sponsors
who make AmateurRadio.com possible:
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
14/16
KB3IFH QSL Cards
InnovAntennas
Hip Ham Shirts
Associated Radio
Expert Linears
American Radio Supply
Georgia Copper
Learn Morse Code
Morse Fusion
Ham Shirts
N3ZN Keys
West Mountain Radio
R&L Electronics
Ni4L Antennas
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
15/16
Alpha Antenna
socialhams
PackTenna
Ears To Our World
Search AmateurRadio.com
Do you like to write?
Interesting project to share?
Helpful tips and ideas for other hams?
Submit an article and we will review it for publication on AmateurRadio.com!
Are you a reporter covering ham radio?
Find ham radio experts for your story.
How to Set Up a Ham Radio BlogGet started in less than 15 minutes!
Recent Posts
Listen to the music
ICQ Podcast Episode 211 – Emergency Comms
AmateurLogic 90: Everybody’s Talking About Antennas
A New Paddle for a New Extra
Amateur Radio Weekly – Issue 111
The ZL1SIX Ocean Floater
Summits On The Air – Colorado StyleIC-7300 LF / MF Receive Performance
Portable Ops 23/45: 20 Meters Was Fun Today!
Announcing: 25th Annual Colorado 14er Event
Copyright © 1995-2016 AmateurRadio.com, All Rights Reserved.
RSS Feed | Sitemap | DMCA ContactEach individual posting is the property of its respective author and the opinions expressed may not represent those of AmateurRadio.com including its editor, staff, or sponsors. Content may not be reproduced without
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm
16
-
8/15/2019 A New Paddle for a New Extra • AmateurRadio
16/16
written permission.
w Paddle for a New Extra • AmateurRadio.com http://www.amateurradio.com/a-new-paddle-for-a-new-extra/?utm