A Moisture-Stable Organosulfonate-Based Metal-Organic … · 2020-01-15 · pressure of 10-2 mtorr...
Transcript of A Moisture-Stable Organosulfonate-Based Metal-Organic … · 2020-01-15 · pressure of 10-2 mtorr...
S1 / 21
Supporting Information for
A Moisture-Stable Organosulfonate-Based Metal-Organic
Framework with Intrinsic Self-Trapped White-Light
Emission
Guiyang Zhang‡, Jinlin Yin‡, Xueling Song & Honghan Fei*
School of Chemical Science and Enginnering, Shanghai Key Laboratory of Chemical
Assessment and Sustainability, Tongji University, Shanghai 200092, P. R. China
Corresponding Author
Author Contributions
‡These authors contributed equally.
Electronic Supplementary Material (ESI) for Chemical Communications.This journal is © The Royal Society of Chemistry 2020
S2 / 21
Experimental Section
Materials
All starting reagents, materials and solvents were purchased from commercial
suppliers (Sigma Aldrich, Fisher Scientific, Alfa Aesar, et al.) and used without
further purification unless otherwise indicated. Purity of the reagents and the solvents
are over 99 % and HPLC grade, respectively. Deionized water was obtained from a
BARNSTEAD PACIFIC RO water purification system.
Solvothermal Synthesis of TMOF-7
In a typical synthesis, CdCl2 (69 mg, 0.3 mmol) and 1,2-ethanedisulfonic acid (68
mg, 0.3 mmol) were adequately dispersed in 10 mL DMF by sonication, followed by
transferring the mixtures into a 15 mL Teflon-lined autoclave and heating statically at
120 ℃ for 72 h. After 72 h, the autoclave was cooled down to room temperature at a
rate of 6 ℃/h and the colorless block crystals were isolated by centrifugation at 2000
rpm for 5 min. The crystals were then washed with ethanol for three times (10 mL ×
3) and dried in air (yield: 94 mg, ~82 % based on Cd). The as-synthetized materials
were incubated in 20 mL methanol over a period of 60 hours, in which fresh methanol
was changed every 12 hours. The MOFs were evacuated at 150 ℃ for 6 hours at a
pressure of 10-2
mtorr on a MICROMERITICS ASAP 2020 chemical/physical gas
sorption analyzer, giving activated guest-free sample. The high phase purity of
TMOF-7 was confirmed by comparing experimental PXRD patterns with theoretical
pattern simulated from the single-crystal X-ray diffraction data. Anal. cal. for
C4H12O6NS2ClCd: C 12.56, H 3.14, N 3.66, S 16.76 (%); found: C 12.99, H 3.15, N
S3 / 21
3.80, S 16.90 (%, activated sample). The μm-sized microcrystalline powders of
TMOF-7 were prepared via manual grinding of the bulk crystals.
Powder X-Ray Diffraction (PXRD)
Approximately 20 mg sample of TMOF-7 (pristine or post-treated) were dried in
vacuum prior to PXRD analysis. The measurement was carried out on a BRUKER
D2 PHASER diffractometer with Cu Kα radiation (λ = 1.5418 Å) at 40 kV, 40 mA
and room temperature. The diffraction patterns were scanned with a speed of 1
s/step, a step size of 0.02° in 2θ, and a 2θ range of 5~40°. Theoretical PXRD pattern
were simulated by using the crystallographic information file collected from the
single-crystal X-ray diffraction experiment.
Single Crystal X-Ray Diffraction (SCXRD)
A single crystal of TMOF-7 suitable for X-ray analysis was chosen under an
optical microscope (NIKON ECLIPSE LV100N POL), and carefully mounted onto
the glass fiber. SCXRD data were collected at 150(2) K using
graphite-monochromated Mo-Kα radiation (λ = 0.71073 Å) from a fine-focus sealed
tube operating at 50 kV and 30 mA on a BRUKER D8 VENTURE diffractometer
equipped with a PHOTON III detector. The crystal-to-detector distance was set 45
mm. More than half-sphere of data was collected using a combination of phi and
omega scans with the scan speeds of 2 s/º for the phi scans and 1 s/º for the omega
scans at 2θ = 0°.
S4 / 21
Diffraction data were processed with the APEX3 software package,[S1]
integrated using SAINT, and further corrected for absorption effects using SADABS.
Space-group was determined by systematic absences, E-statistics, agreement factors
for equivalent reflections, and successful refinement of the structure. The structure
was solved by direct methods and expanded routinely. The model was refined by
full-matrix least-squares analysis of F2 against all reflections using SHELXTL
software package.[S2]
All non-hydrogen atoms were refined with anisotropic thermal
displacement parameters. Thermal parameters for hydrogen atoms were tied to the
isotropic thermal parameter of the atoms to which they are bonded. Further details
for the crystallographic data and structural refinement are summarized in Table S2.
Fourier-Transform Infrared (FT-IR) spectrum
FT-IR spectrum were recorded using a BRUKER ALPHA spectrophotometer
with a wavenumber range of 4000~400 cm-1
, a resolution of 4 cm-1
, and scan times of
32.
Thermogravimetry Analysis (TGA)
TGA was performed using a NETZSCH STA 409 PC/PG differential thermal
analyzer with a platinum crucible. The samples were heated in N2 stream (60 mL/min)
from room temperature to 800 °C with a heating rate of 10 °C/min.
S5 / 21
Chemical and Humidity Resistance Studies
A certain amount of activated TMOF-7 was added to various solvents (DMF,
EtOH or acetone) for 24 h. The samples were then filtrated out, washed by EtOH for
three times and dried in air. The humidity test was performed by incubating
activated TMOF-7 in a chamber at a fixed humidity in the range of 50%~90% RH for
48 h. PXRD patterns and photoluminescence of the samples after humidity
treatment were then performed.
Electrical Conductivity Measurement
Electrical conductivity of a single crystal of TMOF-7 was measured using a CHI
760E electrochemical workstation over a frequency range of 10 Hz~10 MHz with an
input voltage amplitude of 500 mV. Silver paste was coated uniformly onto opposite
side of the crystal and copper wire electrodes were fixed into the paste (Figure S2).
The measurements were taken at room temperature and 50% RH. The resistance (R)
was extrapolated by fitting the semicircles of the Niquist plots using a proposed
equivalent circuit via ZVIEW software package and the conductivity (σ) was acquired
by the equation of σ = l/AR where l and A represent the length and the cross-section
area of the single-crystal, respectively.
Cation Exchange
Appropriately 100 mg TMOF-7 crystals was heated in 120 ℃ oven overnight for
adequate activation, and then incubated into DMF solution containing MnCl2. The
concentrations of the solutions range from 0.5 mol % to 2.5 mol % in order to achieve
S6 / 21
different degree of cation exchange. The suspension was fixed onto a mechanical
shaker at a constant shaking rate of 200 cpm for 6 h to assure sufficient cation
exchange. Then, the solids were isolate by filtration, washed by EtOH for three
times, and dried in air. Inductively coupled plasma optical emission spectra
(ICP-OES, operated on a PERKIN ELMER AVIO 200 ICP-OES spectrometer) was
employed to evidence the successful incorporation of MnII into TMOF-7. TMOF-7
and its derivatives were digested by mixed solvent of D3PO4 (36 wt. % in D2O) and
d6-DMSO for
1H NMR measurements.
Elemental Analysis
Elemental analysis (EA) for C/H/N/S was performed using a THERMAL FLASH
EA 1112 element analyzer.
Steady State Photoluminescence Spectra
The excitation and emission spectra of both the mm-sized single crystals and
μm-sized microcrystals of TMOF-7 were collected at room temperature using a
HITACHI F-7000 spectrophotometer equipped with a 1 kW Xe lamp. The slit width
was set 1 mm.
Ultraviolet-Visible (UV-Vis) Diffuser Reflectance Spectrum
The UV-Vis diffuser reflectance spectrum in 200~1000 nm region was recorded
at room temperature upon a SHIMADZU UV-2600 spectrometer equipped with
S7 / 21
integrating sphere. BaSO4 was used as a reference for 100% reflectance for all
measurements. The μm-sized microscopic powders were packed into the sample cell.
Reflectance spectrum were converted to absorption according to the equation:
A = 2-lg(T%)
where A and T represent the absorbance and reflectance, respectively. The
Kubelka-Munk plot [F(α)hν]1/2
as a function of photon energy (hν) was applied to the
absorption spectra and the optical absorption coefficient, F(α) = A2/2(1-A), is
calculated, where A is the absorbance, h is the Planck constant, and ν is the frequency
of light at a specific wavelength. The extrapolation of the linear region affords the
bandgap value for TMOF-7.
Time-Resolved Photoluminescence
Time-resolved emission data was collected at room temperature using an
EDINBURGH FLS980 steady state/transient state fluorescence/phosphorescent
spectrometer equipped with time-correlated single photon counting (TCSPC) system.
Excitation was provided by an EPL-360PS pulsed diode laser. The average lifetime
was obtained according to the equation:
𝜏avg =∑𝛼i𝜏i
2
∑𝛼i𝜏i 𝑖 = 1,2,3…
where 𝑎𝑖 represents the amplitude of each component and 𝜏𝑖 represents their decay
time. The instrument response was measured to be ~1 ns FWHM by measuring
scattered light from alumina colloidal particles.
S8 / 21
Temperature-Dependent Photoluminescence
Temperature-dependent emission data was collected for μm-sized microscopic
powders using the EDINBURGH FLS980 steady state/transient state
fluorescence/phosphorescent spectrometer at a series of temperature ranged from 77
K to 477 K.
Photoluminescence Quantum Efficiencies (PLQEs)
Absolute PLQE measurements of TMOF-7 were performed on an EDINBURGH
FLS920 steady state/transient state fluorescence/phosphorescent spectrometer with an
integrating sphere (BaSO4 coating) using single photon counting mode. The focal
length of the monochromator was 300 mm. Samples were excited using light output
from a 450W Xe lamp with 3 mm excitation slits width. Emission from the sample
was guided through a single grating Czerny-Turner monochromator and detected by a
Hamamatsu R928P photomultiplier tube. The emission was obtained using a scan step
of 0.2 nm, a scan dwell time of 0.2 s, and an emission slit width of 0.1 mm. The
PLQEs were calculated by the equation: = k𝑓/k𝑎 , in which k𝑓 means the number
of emitted photons and k𝑎 means the number of absorbed photons. Control sample,
Rhadamine-101, was measured using the same method to give a PLQY of 95%,
which is close to the literature value.
Photostability Tests
A 4 W, 365 nm lamp was used as the continuous irradiation source to test the
photostability of TMOF-7. Then, steady-state photoemission measurements were
S9 / 21
performed for the samples which were irradiated for 14 days in air (~50% relative
humidity, room temperature).
Raman Masurements
Solid-state Raman spectra were recorded on a CRIAC 20/30PV full spectrum
microspectrophotometer with an above-bandgap excitation wavelength of 785 nm.
Crystals were placed on quartz slides under Krytox oil, and data was collected after
optimization of microspectrophotometer.
Computational Methods
Density function theory calculations (DFT) were fulfilled by using CP2K
package. The system was described by Perdew-Burke-Ernzerhof (PBE) function with
Grimme D3 correction. Unrestricted Kohn-Sham DFT has been used as the electronic
structure method in the framework of the Gaussian and plane waves method. The
Goedecker-Teter-Hutter (GTH) pseudopotentials, DZVP-MOLOPT-SR-GTH basis
sets were utilized to describe the molecules. A plane-wave energy cut-off of 500 Ry
has been employed. The lattice parameters were fixed at the experimentally measured
values while the atomic positions were optimized. Following Franck-Condon
principle, the optical excitation and emission energies were obtained by calculating
the total energy differences between the excited and the ground states using optimized
ground-state and excited-state structures, respectively.
S10 / 21
Figures and Tables
Figure S1. Crystallographic view of TMOF-7 along a-axis, showing the protonated
dimethylamine cations in its pore channel. Hydrogen atoms are omitted for clarity. Cd
teal, S yellow, O red, C grey, Cl green, N blue.
Figure S2. a) The approach to measure electrical conductivity of a single crystal of
TMOF-7; b) Nyquist plots of a single crystal of TMOF-7 along crystallographic
a-axis and along crystallographic b-axis
S11 / 21
Figure S3. FTIR spectrum for TMOF-7 before and after chemical treatment, and the
characteristic absorption bands (1169 cm-1
, 1067 cm-1
, 607 cm-1
) of sulfonate groups
are highlight.
Figure S4. PXRD patterns of TMOF-7 before and after incubation in different
solvents. The new peaks highlighted by red squares are likely due to the partial
degradation of our MOFs in organic solvents.
S12 / 21
Figure S5. Thermogravimetry curve for TMOF-7.
Figure S6. Tauc plot of TMOF-7, in which (Ahν)2 is a function of the photon energy
(hν). The extrapolation of the linear region estimates the bandgap value of TMOF-7 is
about 4.15 eV.
S13 / 21
Figure S7. Photoluminescence excitation and emission of pristine bulk TMOF-7.
Figure S8. Photoluminescence decay of TMOF-7 measured at 298K (monitored at
390 nm).
S14 / 21
Figure S9. Photoluminescence decay of TMOF-7 measured at 77K (monitored at 390
nm).
Figure S10. Photoluminescence emission of TMOF-7 before (black) and after (cyan)
continuous UV irradiation (310 nm, 67 mW/cm2) for 15 days under ambient condition
(~50% RH, room temperature).
S15 / 21
Figure S11. Photoluminescence emission of TMOF-7 before (black) and after (blue)
incubating in high moisture condition (RH 90 %) for 24 h.
Figure S12. PXRD patterns of TMOF-7 before and after Mn(II) exchange.
S16 / 21
Figure S13. 1H NMR spectra of digested TMOF-7 (black) and TMOF-7-Mn0.9 (red),
showing slight leaching of dimethylamine species during cation exchange.
Figure S14. Photoluminescence decay of mm/μm-sized TMOF-7 at 298 K.
S17 / 21
Figure S15. Photoluminescence decay of TMOF-7 measured at 298 K (monitored at
489 nm).
Figure S16. Temperature dependence of the main emission bandwidth (excluding the
high-energy shoulder) of TMOF-7 and the best fit to the following equation[S3]
.
Г(T) = Г0 + ГLO(e𝐸LO 𝑘B𝑇⁄ − 1)-1 + Гinhe−𝐸b 𝑘B𝑇⁄ (1)
The best fit demonstrated a considerable contribution of the electron-phonon
coupling [ΓLO of 79(2) meV] to the broadening of photoluminescence and phonon
energy of 14(1) meV. The latter corresponds to a frequency of 116 cm-1
, which resides
well in the range of Cd—Cl stretching frequency in TMOF-7 (Figure S17). All of
these photophysical studies suggest the high-energy shoulder and the low-energy
broadband emission of TMOF-7 are probably attributed to the self-trapped excitons
(from electron-phonon coupling in the deformable lattice) and free excitons,
respectively.
S18 / 21
Figure S17. Raman spectrum of TMOF-7.
Table S1. Photophysical properties of TMOF-7 before and after the Mn2+
incorporation.
Material x y FWHM (nm) CCT (K) CRI PLQE (%)
TMOF-7 0.28 0.34 230 8497 82 11
TMOF-7-Mn0.3 0.30 0.35 225 6720 86 7
TMOF-7-Mn0.6 0.36 0.37 219 4297 92 8
TMOF-7-Mn0.9 0.38 0.38 202 3862 88 11
S19 / 21
Table S2. Photoluminescence parameters of recently reported intrinsic white-light emitters.
Material PLQE (%) CRI Reference
TJU-3 1.8 78 Angew. Chem. Int. Ed. 2017, 56, 14411.
TJU-4 11.8 68 Angew. Chem. Int. Ed. 2017, 56, 14411.
TJU-5 2.0 N.A. Angew. Chem. Int. Ed. 2017, 56, 14411.
TJU-6 5.4 N.A. Chem. Sci. 2018, 9, 1627.
TJU-7 1.8 N.A. Chem. Sci. 2018, 9, 1627.
TMOF-5(Cl) 6~8 85 Angew. Chem. Int. Ed. 2019, 58, 7818.
TMOF-5(Br) 1.5 89 Angew. Chem. Int. Ed. 2019, 58, 7818.
(N-MEDA)PbBr4 0.5 85 J. Am. Chem. Soc. 2014, 136, 1718.
(EDBE)PbBr4 9 84 J. Am. Chem. Soc. 2014, 136, 13154.
(EDBE)PbCl4 2 81 J.Am. Chem. Soc. 2014, 136, 13154.
(PEA)2PbCl4 <1 84 Chem. Mater. 2017, 29, 3947.
(API)PbCl4 <1 93 J. Mater. Chem. C 2018, 6, 1171.
(MPenDA)PbBr4 3.4 91 Chem. Commun. 2018, 54, 4053.
(CyBMA)PbBr4 1.5 N.A. ChemSusChem 2017, 10, 3765.
α-(DMEN)2PbBr4 N.A. 73 J.Am. Chem. Soc. 2017, 139, 5210.
(HMTA)3Pb2Br7 7 N.A. Chem. Sci. 2017, 8, 8400.
(H2DABCO)Pb2Cl6 2.5 96 Chem. Sci. 2015, 6, 7222.
(C6H18N2O2)Pb0.95Mn
0.05Br4
12.5 85 Chem. Mater. 2019, 31, 5788.
(BAPP)Pb2Br8 1.5 87 Adv. Mater. 2019, 31, 1807383.
(TDMP)PbBr4 45 75 Adv. Mater. 2019, 31, 1807383.
S20 / 21
Table S3. Crystallographic data and structural refinement for TMOF-7.
Identification code TMOF-7
Empirical formula C4H12O6NS2ClCd
Formula weight 382.12
Temperature 150 (2) K
Wavelength 0.71073 Å
Crystal system triclinic
Space group P-1
Unit cell dimensions a = 8.0898 (9) Å α = 113.630(4)°
b = 8.7429 (11) Å β = 100.423(4)°
c = 9.3861 (11) Å γ = 106.839(4)°
Volume 547.71 (11) Å3
Z 2
Density (calculated) 2.317 g/cm3
F (000) 376
Crystal size 0.23 × 0.13 × 0.10 mm3
θ range for data collection 3.048 ~ 27.552°
Limiting indices -10 ≤ h ≤ 10, -11 ≤ k ≤ 10, 0 ≤ l ≤ 12
Reflections collected 2521
Independent reflections 2409
Completeness to θ = 26.73° 100%
Absorption correction empirical
Data / restraints / parameters 2521/0/142
Goodness-of-fit on F2 1.190
Final R indices [I > 2σ (I)] R1 = 0.0180, wR2 = 0.0480
R indices (all data) R1 = 0.0199, wR2 = 0.0468
Largest diff. peak and hole 0.407 and -0.565 eÅ-3
S21 / 21
References
S1. APEX-II, 2.1.4, Bruker-AXS: Madison, WI, 2007.
S2. SHELXTL, Crystal Structure Determination Package, Bruker Analytical X-ray Systems Inc.:
Madison, WI, 1995~99.
S3. Lee, J.; Koteles, E. S.; Vassell, M. O., Phys. Rev. B 1986, 33: 5512-5516.