› files › Documentation › PluginSpecific... · MaxxECU Plugin - Engine Specifics Audi...
Transcript of › files › Documentation › PluginSpecific... · MaxxECU Plugin - Engine Specifics Audi...
Fig 1 - MaxxECU Audi AAN kit consist of the following parts: - MaxxECU Audi AAN kit consist of the following parts:1. MaxxECU CMC connector2. Audi vehicle harness adapter.3. 16-pin extra connector. 4. 3-pin connector for extra 0-5v sensor (ex. pressure sensor).
4.
3.
2.
1.
2015-10-16
MaxxECU Plugin - Engine SpecificsAudi S2/S4/S6 (AAN)
Maxxtuning AB - www.maxxtuning.eu - [email protected]
ECU installationStock Engine Control Unit (ECU) on this vehicle is mounted on passenger side floor, under the glove compartment.• Remove the carpet and the black large plastic guard, where the ECU is located.• Disconnect the stock ECU from vehicle harness connector.• Install MaxxECU harness into vehicle harness connector.• Install included MAP-sensor into engine manifold with included hose kit.• MaxxECU uses stock air temperature sensor (highly recommended to replace it to get a more accurade IAT reading).
Dynotuning Engine Management Motorsport 2
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
86
87
85
30
AIR TEMP SENSOR, (F2)
5V SENSOR SUPPLY, (G1)
THROTTLE SENSOR, (G2)
COOLANT SENSOR, (F1)
ANALOG IN 1, TEMP, (J1)
ANALOG IN 2, TEMP, (J2)
ANALOG IN 3, 0-5V, (J3)
ANALOG IN 4, 0-5V, (J4)
DIGITAL IN 1, (K3)
DIGITAL IN 2, (K4)
SENSOR GND
IGNITION CYL 1, (A2)
IGNITION CYL 2, (A3)
IGNITION CYL 3, (B2)
IGNITION CYL 4, (B3)
IGNITION CYL 5, (C2)
IGNITION CYL 6, (C3)
IGNITION CYL 7, (D2)
IGNITION CYL 8, (D3)
INJECTOR CYL 1, (K1)
INJECTOR CYL 2, (K2)
INJECTOR CYL 3, (M1)
INJECTOR CYL 4, (M2)
INJECTOR CYL 5, (M3)
INJECTOR CYL 6, (L3)
INJECTOR CYL 7, (L2)
INJECTOR CYL 8, (L1)
GP OUT 1, (B4)
GP OUT 2, (C4)
GP OUT 3, (D4)
GP OUT 4, (E4)
GP OUT 5, (A1)
GP OUT 6, (B1)
GP OUT 7, (C1)
TACH/GP OUT 8, (A4)
WBO2 HTR PIN 4, (D1)
TRIGGER
HOME/CAM
12V ECU, (M4)
ENGINE GROUND
12V ECU, (C)
12V IGNITION, (D)
12V INJECTORS
12V GP OUT
12V LAMBDA (PIN3)
Text in blue
Relay wirings
+12V
from ECU GPOfrom ECU GPO
Fuse!
Fan / pump etc.
WBO2 HTR PIN4, (D1)
12V LAMBDA (PIN 3)
Extra inputs.MaxxECU AAN Plugin has 4 extra flexible inputs.AIN 1, temp sensor or switches.AIN 2, temp sensor or switches.AIN 3, 0-5V input.AIN 4, 0-5V input. Extra 3-pin connector (4).
Extra outputs.MaxxECU AAN Plugin offers 4 extra outputs for flexible control like boost control, fan control.INJ 7, INJ 8, GPO 3, GPO 4 (GND switched outputs).
Fig 3 - 3-pin Superseal connector.1: Signal GND.2: AIN 4 (0-5V) input.3: +5V from ECU.
9: Wideband.10: Wideband.11: Wideband.12: +12V (output).13: GND.14: AIN 1 (temperature / switch) (input).15: AIN 2 (temperature / switch) (input).16: AIN 3 (0-5V) (input).
1: Wideband.2: Wideband.3: Wideband.4: Wideband.5: INJ 7 (output).6: INJ 8 (output).7: GPO 3 (output).8: GPO 4 (output).
16-pin connector
Fig 2 - Extra connector (3)seen from cable side.
Plugin Trigger
Audi 5-cylinder engines is using an unique trigger decoder which take use of three inputs.Trigger + HOME + DINx.It’s extremely important that HOME signal (flywheel sensor nr 2) is triggered in the middle of 2 Trigger teeths.In MTune, RealTime Data tab --> Trigger, ”Home position” which should be within 10-90% to perform best. Be sure to also check this value on higher RPMs.The only thing that controls the HOME POSITION is the polarity of the HOME input, please modify (if possible) using ”Trigger Polarity”, Inputs ---> Trigger/Home inputs and ”Trigger input”.
NotesMaxxECU has some built in output test and diagnostics, see Diagnostics ---> Output test to test certain outputs. Diagnostics ---> Output test to test certain outputs. Diagnostics ---> Output testThis will only work if fuel pump is set to ”Always active” since fuel pump relay is also powering injectors and ignition.