A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
-
Upload
ramoutar-ken-seecharran -
Category
Documents
-
view
217 -
download
1
Transcript of A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
1/57
By Ramoutar (Ken) Seecharran (MEIZ)By Ramoutar (Ken) Seecharran (MEIZ)
Plant Superintendent, Frontier Sprl, DR Congo
A CASE FOR FORGED MILL BALLSCASE FOR FORGED MILL BALLS
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
2/57
FIRST QUANTUMFIRST QUANTUMs ACTIVITIESs ACTIVITIES
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
3/57
PLACEFIX MAP SHOWING FRONTIER MINEPLACEFIX MAP SHOWING FRONTIER MINE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
4/57
BRIEF HISTORY OF FRONTIER MINEBRIEF HISTORY OF FRONTIER MINE
The deposit was known to exist, but not fully quantified
The Japanese had shown interest during the Gecamine erabut depressed copper price and high project cost curtailedproject implementation
First Quantum was operating the Lonshi mine to the south east
of this deposit, in the Pedicle, so logistically, it was easy forus to carry out extensive drilling
Once quantified, the board was committed to our development
of copper deposits in this part of Africa, and approved the project
The project was implemented at a cost of $US226m
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
5/57
For the valuable mineral(s) of an ore to be economically separatedfrom the waste, host rock (gangue), the ore has to be broken downto a small enough size (comminuted), to liberate it (them) from therock matrix. Comminution represents the most expensive part of aplants circuit. At this point, we minerals engineers use our knowledgeof the properties of the various minerals to exploit noticeable differencesin those properties, between the valuable mineral(s) and their ganguecounterparts.
These differences in properties could be: Difference in specific gravity Difference in solubility in a suitable dissolving chemical Difference in magnetic susceptibility or,
Difference in surface properties
BEFORE THESE DIFFERENCES CAN BE EXPLOITED, WE MUSTPRESENT THE MINERALS TO THE SEPARATION STAGE INAS UNIFORM A SIZE AS POSSIBLE, IDEALLY, ALL OF THE SAMEGRAIN SIZE.OR AS NEAR TO THE SAME SIZE AS POSSIBLE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
6/57
So once broken, the grains of minerals in the ore must be sized.
Those which meet this size requirement progress to the separationstage, those failing, are given another chance to be broken.Therefore, the ideal sizing machine should be some form of a screen,however, the huge tonnages we treat these days will not make screening
feasible. Hydrocyclones are used as a practical compromise.A hydrocyclone utilises drag force to remove the fines through the vortexfinder in the middle of the cone while the coarser particles are actedupon by centrifugal force and forced outwards towards the wall. Theythen migrate downwards under gravity and get another chance tobe broken.
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
7/57
THE NEED FOR COMMINUTIONTHE NEED FOR COMMINUTION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
8/57
POLISHED SECTIONS OF FRONTIERPOLISHED SECTIONS OF FRONTIERs OREs ORE
FREE CuFeS2LOCKED CuFeS2
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
9/57
POLISHED SECTIONS OF CONGOLESE/ZAMBIAN Cu ORESPOLISHED SECTIONS OF CONGOLESE/ZAMBIAN Cu ORES
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
10/57
Traditionally, comminution in a concentrator plant was carried out in afew well defined steps, namely:
Primary crushing.underground or on surface
Secondary crushing.on surface in the concentrator plant Tertiary crushing.in the concentrator plant, and in closed circuit witha screen
Ball milling.in the concentrator plant
Before the refinement of tertiary crushing, this function was performedby rod milling. Rod mills became unfashionable in the early 1960sas crusher bowl and mantle profile research enabled ore to be crushedsuccessfully to a size below 10mm without causing metal to metalcontact between the crushing faces.
Crushing and screening plants had numerous operational problemssuch as Bogged crushers, Blinded screens and Blocked chutes. A
phenomenon we plant operators called the three Bs!
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
11/57
FRONTIERFRONTIERs OPEN PITs OPEN PIT
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
12/57
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
13/57
PROCESS DESCRIPTION AT FRONTIERPROCESS DESCRIPTION AT FRONTIER
Run of mine ore is primary crushed and stockpiled Crushed ore at a size of 80% smaller than 112mm is fed to a
Semi Autogenous Grinding (SAG) mill SAG mill product is fed to a cluster of hydrocyclones (sizing device) wherethe fine product progresses to the separation stage and the coarse fractionis routed to a ball mill and given a second chance to be broken, the ball millproduct is fed to the same cluster of hydrocyclones, in order to close the circuit
Separation of valuable mineral from waste is carried out using froth flotation The copper minerals recovered is thickened and filtered to produce a solidcake containing about 9.5% moisture
The waste rejected (tailings) is thickened and disposed of in a responsible
manner in a tailings impoundment All water used in the plant is recycled in the process
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
14/57
GYRATORY CRUSHER AT FRONTIERGYRATORY CRUSHER AT FRONTIER
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
15/57
CRUSHED ORE STOCKPILECRUSHED ORE STOCKPILE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
16/57
SAG and BALL MILLS AT FRONTIERSAG and BALL MILLS AT FRONTIER
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
17/57
INSIDE THE SAG MILLINSIDE THE SAG MILL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
18/57
SEPARATION UTILISING FROTH FLOTATIONSEPARATION UTILISING FROTH FLOTATION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
19/57
People being exposed to SAG milling for the first time often
underestimate the crushing forces present in these mills. Theyare normally of >32 feet in diameter. So the crushing force atthe toe of the crop load, the cataracting end, is phenomenal.Some studies suggest pressures as high as 20 bars are present.
Due to the shortage of suitable grinding media in Sub-SaharanAfrica, we were forced to start our plant with sub-standardgrinding media in October 2007. Time was of the essence as wewere faced with an entirely new work force and on-the-job
training had to be expeditiously carried out.
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
20/57
POROUS CAST BALLPOROUS CAST BALL-- INVITING DISASTERINVITING DISASTER
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
21/57
POROUS BALLS AFTER 20 Hrs OPERATIONPOROUS BALLS AFTER 20 Hrs OPERATION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
22/57
A WEEK LATER!!!!A WEEK LATER!!!!
EVEN THE BETTER QUALITY CAST BALLSEVEN THE BETTER QUALITY CAST BALLS
HAD THEIR OWN PROBLEMSHAD THEIR OWN PROBLEMS
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
23/57
HAD THEIR OWN PROBLEMSHAD THEIR OWN PROBLEMS.caused by the intense pressure in the SAG mill
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
24/57
BROKEN BALLS ARE DETRIMENTAL TO SAG MILLING OPERATIONSBROKEN BALLS ARE DETRIMENTAL TO SAG MILLING OPERATIONS
They take up useful space that could be occupied by ore. Beingstreamlined, they do not get flushed out easily
They are too light to have enough kinetic energy to break rock
They add to power consumption, by their weight and being pinnedto the mill shell, they get carried up to a point beyond which a wholeball leaves the shell on its trajectory, thus adding more load to the
motor
They add to steel consumption, Fe ions are detrimental to flotation.Sulphide minerals get depressed
When hammered against the discharge grate, they cause peening.Peening reduce the flow through a mill
They act as a cushion against which rocks are hammered by balls,
so breakage is less effective
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
25/57
Cast balls are not suitable for a SAG mill
The outer crust is hard, typically in excess ofBrinell hardness 450. This quickly diminishes
towards the centre of the ball.
It is for this reason, when you open a SAG mill,in which cast balls were fed, you see balls ofpredominantly one size.
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
26/57
DATA I COMPILED FOR ZCCM IN 1989DATA I COMPILED FOR ZCCM IN 1989under a different incarnation
BRINELL HARDNESS ACROSS BALL
050
100
150
200250
300
350
400450
500
1 2 3 4 5 6 7 8
PICTURE FROM INSIDE KANSANSHIPICTURE FROM INSIDE KANSANSHI SAG MILLSAG MILL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
27/57
PICTURE FROM INSIDE KANSANSHIPICTURE FROM INSIDE KANSANSHIs SAG MILLs SAG MILLNOTE BALLS OF ONE SIZE
EFFECTS OF SOFT CENTRE OF A CAST BALLEFFECTS OF SOFT CENTRE OF A CAST BALL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
28/57
EFFECTS OF SOFT CENTRE OF A CAST BALLEFFECTS OF SOFT CENTRE OF A CAST BALLuneven wear
EFFECTS OF SOFT CENTRE OF A CAST BALLEFFECTS OF SOFT CENTRE OF A CAST BALL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
29/57
EFFECTS OF SOFT CENTRE OF A CAST BALLEFFECTS OF SOFT CENTRE OF A CAST BALLdimpled ball
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
30/57
WHAT WAS THE SOLUTION?.....FORGED BALLSThe bar from which a forged ball is made is cut into shots, reheatedand hammered at least 30 times. Compacting and hardening it. Theinitial hot rolling of the bar followed by rapid cooling, reheating and
subsequent hammering, also changes the microstructure from oneresembling pearlitic to that closer to martensitic. The steels grainstructure aligns and stretches in the forging process, thus creating astronger, more compact steel. The balls are then quenched and
reheated for tempering and stress relieving, respectively.
We therefore then get a ball which is of uniform hardness andweight. A ball which can withstand the harsh conditions in a SAG mill.The difference in weight between a well forged ball and an excellent
cast counterpart could be about 9%
Here networking helped us. ECLIPSE foundry in South Africa washelpful. I knew Humphrey, their Zambian representative for many
years, and studied at university in the UK with Jacob, their ex MDin South Africa.
PHOTOMICROGRAPHS OF STEELPHOTOMICROGRAPHS OF STEEL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
31/57
PHOTOMICROGRAPHS OF STEELPHOTOMICROGRAPHS OF STEEL
PEARLITIC MARTENSITIC
ECLIPSE FOUNDRYECLIPSE FOUNDRYs FORGED BALLs FORGED BALL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
32/57
ECLIPSE FOUNDRYECLIPSE FOUNDRY s FORGED BALLs FORGED BALL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
33/57
Although proved to be successful, the volumeof forged balls we required, ECLIPSE wasunable to supply.
So, armed with valuable information gathered from theECLIPSE trial, we went to the European Union, from
where our sister plant in Mauritania was sourcing theirSAG mill balls.
Long lead time and transport logistics remain a nightmare.
I was informed that ECLIPSE has plans to expand theirproduction capacity, we welcome such a symbiotic move.
FORGED MILL BALLS FROM SPAINFORGED MILL BALLS FROM SPAIN
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
34/57
FORGED MILL BALLS FROM SPAINFORGED MILL BALLS FROM SPAIN
HAND FORGING IN CHINAHAND FORGING IN CHINA
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
35/57
HAND FORGING IN CHINAHAND FORGING IN CHINA
MILLING INFORMATION SHOWN ON THE COMPUTERMILLING INFORMATION SHOWN ON THE COMPUTER
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
36/57
MILLING INFORMATION SHOWN ON THE COMPUTERMILLING INFORMATION SHOWN ON THE COMPUTER
EMPHASIS ON CENTRE HARDNESSEMPHASIS ON CENTRE HARDNESS
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
37/57
AERIAL VIEW OF THE PLANTAERIAL VIEW OF THE PLANT
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
38/57
FINISHED PRODUCTIONFINISHED PRODUCTION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
39/57
CURRENT MILL BALL PROFILECURRENT MILL BALL PROFILE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
40/57
BENEFITSBENEFITS
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
41/57
We have found that throughput has increased, as grindingis now more efficient
The quality of the ground ore has improved
Steel consumption has decreased, due to less
ball breakage and a more competent ball
Grinding cost has decreased, steel consumption droppedfrom about 550 g/tonne of ore milled to about 450.
It is currently running at about $US 1.15 per tonne of ore milledwe are confident that this will reduce as the circuit is optimised
MILL BALLS WORLDWIDEMILL BALLS WORLDWIDE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
42/57
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
43/57
ANY QUESTIONS????NY QUESTIONS????
HARDNESS TESTINGHARDNESS TESTING
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
44/57
BRINELL - A hardened ball of specified diameter is impressedinto the materials surface, at a known pressure. The Brinell
hardness number results from calculations involving the loadand the spherical area of the balls impression.
ROCKWELL This method involves measuring the depth ahardened steel ball or a diamond penetrates into the materialbeing tested, under controlled loading.
STEEL MANUFACTURING PROCESSSTEEL MANUFACTURING PROCESSmicrostructure
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
45/57
microstructure
STEEL MANUFACTURINGSTEEL MANUFACTURING
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
46/57
HARDNESS OF MARTENSITE WITH CARBON CONTENTHARDNESS OF MARTENSITE WITH CARBON CONTENT
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
47/57
FRONTIERFRONTIERs FLOWSHEETs FLOWSHEET
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
48/57
BEST EVER DAYBEST EVER DAYs RESULTs RESULT
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
49/57
FIRST QUANTUMFIRST QUANTUMs PRODUCTION PROFILEs PRODUCTION PROFILE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
50/57
15 YEAR COPPER PRICE15 YEAR COPPER PRICE
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
51/57
OROGENESIS, MINERALS FORMATIONOROGENESIS, MINERALS FORMATION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
52/57
Cu PRICE IN JAN 2006 centsCu PRICE IN JAN 2006 cents
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
53/57
NORMAL RUNNING and OVERLOADED MILL
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
54/57
PEENING OF DISCHARGE GRATESPEENING OF DISCHARGE GRATES
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
55/57
HYDROCYCLONESHYDROCYCLONES
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
56/57
HYDROCYCLONE OPERATIONHYDROCYCLONE OPERATION
-
8/14/2019 A Case for Forged Mill Balls - EIZ Meeting, Livingstone, Zambia, 2008
57/57