99-58141 3 4 FORD ESCAPE 2008 MERCURY MARINER 2008 95-5814 DASH DISASSEMBLY Disconnect the negative...
Transcript of 99-58141 3 4 FORD ESCAPE 2008 MERCURY MARINER 2008 95-5814 DASH DISASSEMBLY Disconnect the negative...
INSTALLATION INSTRUCTIONS FOR PART 99-5814
99-5814
APPLICATIONSFORD Escape 2008
MERCURY Mariner 2008
KIT FEATURES
• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Mount Units Provision
• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket • G) (2) Spare Radio Housing Panel Clips
KIT COMPONENTS
A
TOOLS REQUIRED:Small Flat Blade Screwdriver/ Panel Removal Tool
• Socket Set
1-800-221-0932 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
DE
C
F G
Dash Disassembly- Ford Escape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2- Mercury Mariner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2
Kit Assembly- Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TABLE OF CONTENTS
99-5814
Note: Refer also to the instructions included with the aftermarket radio.
Note: There are (2) extra radio housing panel clips included with the kit incase removal of the kit is necessary at any time.
1
3
4
FORD ESCAPE 2008MERCURY MARINER 2008
95-5814 DASH DISASSEMBLY
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unclip and remove the a/c vent panelabove the radio. (Figure A)
Remove the (2) 7 MM screwsexposed at the top of the factoryradio panel. (Figure B)
Unclip the accessory socket/switch/aux input panel below the radio.Unplug and remove the panel. (Figure C)
Continue on page 2.
2
C
B
A
2
FORD ESCAPE 2008MERCURY MARINER 2008
95-5814 DASH DISASSEMBLY
Continue to kit assembly
Remove the (2) 7 MM screws exposedat the bottom of the factory radiopanel. (Figure D)
5
Remove (4) Torx screws securing theclimate controls to the factory radiopanel. Remove the climate controlsand retain them with the factoryscrews for use during kit assembly.(Figure E)
7
Slide radio out and remove (1) 8mmbolt from the right side securing theground strap to the radio brackets.Unplug and remove the radio.
6
REAR CLIMATE CONTROL
REAR OF RADIO
E
D
3
99-5814 KIT ASSEMBLY
KIT PREPARATION
A
REAR CLIMATE CONTROL
TWO PRE-INSTALLEDRETAINING CLIPS
B
TWO EXTRARADIO HOUSINGRETAINING CLIPS
1 Attach the climate control to the radiohousing using the factory hardwareremoved in step 7 of dash disassembly.(Figure A)
Note: There are (2) extra radio housingpanel clips included with the kit in caseremoval of the kit is necessary at anytime. (Figure B)
Continue to kit assembly.
99-5814 KIT ASSEMBLY
4
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Slide the DIN cage into the radio hous-ing and secure by bending the metallocking tabs outward. (Figure A)
1
Slide the aftermarket radio into the DINcage and until it snaps into place.(Figure B)
2
Snap the pocket into the radio housing.(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-5814 KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)
1
Slide the radio into the radio housinguntil it snaps into place. (Figure B)
2
Snap the trim plate onto the front ofthe Radio Housing. (Figure B)
3
Snap the Pocket into the radio housing. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-5814 KIT ASSEMBLY
6
DOUBLE DIN RADIO PROVISION
Cut and remove the center bar fromthe radio housing. (Figure A)
1
Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)
2
Slide the Double DIN radio into theDDIN bracket/radio housing assemblyand secure the radio to the assemblyusing the screws supplied with theradio. (Figure C)
3
Snap the Double DIN trim plate ontothe front of the radio/housing assem-bly. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
99-5814 KIT ASSEMBLY
7
STACKED ISO MOUNT UNITS PROVISION
Cut and remove the center bar fromthe radio housing. (Figure A)
1
Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)
2
Slide the stacked ISO mount units intothe bracket/housing assembly andsecure the units to the assembly usingthe screws supplied with the units.(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN trim plate ontothe front of the radio/housing assem-bly. (Figure C)
4
99-5814 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
8
NOTES
9
99-5814
99-5814 INSTRUCTIONS
1-800-221-0932 REV. 07/16/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-5814
www.metraonline.com