863 FILTERING 8ed. 06.06 new controller SA...FIRST COMMISSIONING AND ROUTINE START - UP FIRST...
Transcript of 863 FILTERING 8ed. 06.06 new controller SA...FIRST COMMISSIONING AND ROUTINE START - UP FIRST...
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
OOOdddiiisssMMMaaatttiiiccc®®® EEEllleeeccctttrrriiiccc FFFiiilllttteeerrr
SSeerriieess 886633--SSAA
Installation, Operation & Maintenance
Manual
Models
86302 (2”)
86303 (3”)
86304 (4”)
86306 (6”)
86308 (8”)
86310 (10”)
86312 (12”)
86314 (14”)
Board No. 86302
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
CONTENTS
Page
Technical Specification ……………………………………... 3
Filtration Screens ……………………………………………. 3
Materials ……………………………………………………… 4
Construction ………………………………………………….. 4
Operational Principles ………………………………………. 5
Operational Modes ………………………………………….. 6
Installation ……………………………………………………. 7
First Commissioning and Routine Start-up ……………….. 8
Automatic Operation ………………………………………… 9
Continuous Operation ………………………………………. 9
Changing Parameters On The PLC ……………………… 15
Control Box …………………………………………………… 15
Maintenance …………………………………………………. 17
Trouble Shooting Table …………………………………….. 19
Parts Breakdown …………………………………………….. 20
Parts List ……………………………………………………… 22
Hydraulic Scheme …………………………………………… 23
Head Loss/ Flow Rate Diagram ……………………………. 24
General Dimensions ………………………………………… 25
Electric Drawings ………………………………………… 15
ODIS takes all possible precautions in packing each equipment
item to prevent damage during shipment. Carefully inspect each
item, and if damage occurred, please report ODIS immediately.
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
General Data
Min. Working Pressure 2 bar 30 psi
Max. Working Pressure 10 bar 150 psi
For other pressure consult ODIS representative
Screen area & Maximum Flow Rates
In/Out – dia. Max. Flow Rate Flush Flow Rate Screen Area
Model Inch mm m3/h gpm m3/h gpm Sq.cm Sq.inch
86302 2” 50 25 110 8 35 2500 390
86303 3” 80 40 170 8 35 2500 390
86304 4” 100 80 350 10 44 4000 620
86306 6” 150 150 660 10 44 4000 620
86308 8” 200 300 1300 12 53 6000 930
86310 10” 250 400 1750 12 53 6000 930
86312 12” 300 470 2050 14 62 8000 1240
86314 14” 350 550 2400 14 62 8000 1240
The max. flow rate refers to screens over 200 microns/ less than 80 mesh
For a finer filtration degrees consult our representative.
Screen Grades
mesh 500 300 200 150 100 80 40
micron 30 50 80 100 150 200 400
* Other screen grades’ are available.
Electrical Data
Mains 3 Phase 380V – 50 Hz, 220V/440V – 60 Hz
Drive Assembly 1/3 HP, 1/4 KW
Control PLC operating at 24V DC
For other power supply consult ODIS representative
TECHNICAL SPECIFICATION
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
Filter housing : Carbon Steel , electrostatic powder coating
Optional - Stainless Steel .
Filtration Screens :Stainless Steel 316
Gaskets : SBR (Synthetic Rubber)
Optional - other materials
The standard housing of the filter is constructed of carbon steel, which has a 100
micron protective coating of extra durable polyester, applied electrostatically and oven
cured on a zinc-phosphate layer, for maximal anti-corrosion protection both internally
and externally
Access to the internal of the filter is through a removable bolted cover.
This allows for easy access for servicing and maintenance purposes. All immersed
parts are constructed of either plastic or non-corrosive metals, allowing for extended
service life.
Optional materials are available for special applications ;contact our
representative for more information.
On the end of the filter housing the electric worm-gear motor is mounted, performing
simultaneously two movements during the flushing cycle:
a. Rotation of the collector assembly with a unique designed SA (patent pending)
suction nozzles to clean the screen on its entire perimeter.
b. Longitudinal motion of the collector assembly with all the nozzles to clean the
screen on all it’s length.
Both actions clean all the surface of the filtering screen in a helical movement. The
rotation is transmitted from the worm-gear motor to the collector assembly by a sliding
key, while the longitudinal motion is transmitted by a square, double thread screw.
MATERIALS
CONSTRUCTION
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
1. INLET 5. OUTLET 9. WORM GEAR MOTOR
2. COARSE SCREEN 6. FLUSHING VALVE 10. CONTROLLER
3. FINE SINTERED SCREEN 7. FLUSHING CHAMBER
4. SUCTION NOZZLE (P) 8. COLLECTOR
(P) – Patent Pending
A. Normal flow pattern
The raw water enters the filter inlet and passes through the coarse screen, the first
stage of filtration. This prevents passage of large particles which may damage the
filter internals.
The water then enters the second stage of filtration, where the fine sintered screen
is located. This screen consists of a multi-layer sintered screen of stainless steel
woven mesh sintered together.
As the water passes through this screen, the solids accumulate creating a “cake” of
dirt on the surface of the screen. This cake performs finer filtration than the
screens itself, resulting in increased filter efficiency. The cake creates also a
pressure differential across the screen.
This differential is monitored by the control system, and a flushing cycle is
activated once the predetermined differential is achieved.
OPERATING PRINCIPLES
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
B. Flushing cycle
When the predetermined differential pressure is reached (as preset on the D.P.
switch gauge) the controller activates the flushing valve (opens it) and the gear
motor.
The pressure differential between the pressure inside the filter and at the open valve
to the atmosphere produces a back-flushing effect at the unique SA (patent pending)
nozzles, removing accumulated solids from the screen to the drain.
The unique design of the S.A nozzles achieves an increased suction and
significantly decreasing in the water consumption during flushing, due to accurate
contact point between the unique S.A nozzle and the screen. The spiral motion of the nozzles as mentioned above cleans the all area of the
screen.
The same Flushing cycle may be activated by the controller - by the Preset Timer or
by the Manual Flushing button (Test).
C. Continuous flushing
Means the flushing of the fine sintered screen continuously, through the suction
nozzles. The flushing valve and the worm-gear motor are activated continuously.
The “Continuous Flushing” is selected manually by the operator.
This efficient filter is automatic and easy to operate.
Its operating modes are as follows:
1) Filtration - The normal function of the filter, until a flushing mode is activated.
2) Automatic Flushing – Flushing of the screen through the suction nozzles, when
activated by time or DP. The gear-motor and the flushing valve are activated
simultaneously by the controller. The Yellow Flushing light (on the control board)
is ON.
The timer activates the flushing cycle, if the D.P. is not activated.
3) Continuous Flushing -
Back flushing of the screen through the suction nozzles. The gear motor and the
flushing valve are activated continuously and the Yellow Flushing light is ON.
This manual mode is selected by the operator.
4) Malfunction mode – This mode takes place
a. When the overload is tripped.
b. When both micro-switches are pressed down at the same time, or when
both micro-switches are short-circuited.
OPERATING MODES
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
c. The motor works for more than T2 (= 60 seconds) between micro
switches.
Then the RED Fault Light (on the control board) is ON.
WARNING : Maximal pressure 10 bar (150 psi).
If the pressure is not controlled effectively, a pressure relief valve must be installed
before the filter.
Prevent back-pressure or reverse flow - install a mechanical non-return valve on each
filter outlet.
NOTE: Install isolation valves at inlet & outlet. These valves would service the filter whenever needed, and in addition the outlet valve can be used to adjust the flow rate
whenever needed.
Install the filter in any position with enough space for servicing and dismantling, but
horizontally is recommended.
Water inlet and outlet directions are clearly marked by an arrow.
Install a mechanical non-return valve at outlet.
Connect a drain pipe with no appreciable resistance.
Check for leaks.
INSTALLATION
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
NOTE: The differential pressure switch and timers have been preset to the proper
settings. Do not adjust prior to start-up.
1. Check that the line pressure will always be at least 2 bar (20mWC) at the filter
inlet during the flushing cycle.
2. Check that there are no upstream pipeline restrictions.
3. Check that the filter is mounted in the correct flow orientation as indicated by
the arrows on the body.
4. Check that the flushing valve is mounted properly.
5. Check that the tubing connections are completed.
6. Check that power is available to the Electrical Control Box and that the main
switch on the control box is in the “OFF” position.
7. Check that the flushing valve drain lines are installed.
8. Check that the upstream and downstream isolation valves are closed.
9. Check that adequate space is available around the filter for maintenance as
indicated in dimensions drawing page 21.
1. Slowly open the inlet valve to the filter allowing the filter to pressurize.
2. Check for any external leakage and eliminate.
3. Slowly open the outlet valve of the filter (if installed).
4. Turn the main switch ON.
NOTE: An automatic procedure will find the right moving direction.
5. Verify that all power supply and all machine elements are connected.
6. Verify input voltage is correct.
7. Turn on main switch wait 5 sec.
8. Push the TEST push button for two seconds. See the movement of the screw.
NOTE: The filter will perform its first flush and will stop, (between the limit
switches). During flushing ensure that the filter inlet pressure is higher than
2 bar (20mWC).
After this first operation the filter passes into automatic mode (command
switch: on "AUTO" position), at any given time pressing the TEST button
will cause one flush cycle.
9. Initiate a manual flushing; observe the inlet and flushing chamber pressures.
The flushing chamber pressure should be between 1.2 to1.5 bar below inlet
pressure during the flushing cycle.
FIRST COMMISSIONING AND ROUTINE START - UP
FIRST COMMISSIONING
START - UP
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
1. The filter will perform a flushing cycle after interval (T6) time in which no
flushes took place.
2. The filter will perform a flushing cycle due to the pressure differential switch
command (D.P.), and will stop near the limit switches.
3. If the pressure differential remains on, the filter will continue its flushing.
4. Counter CTMR (C2) will count the number of flushes due to TFmin time.
5. Counter CDP (C3) will count the number of flushes due to pressure differential.
6. Counter fault (C4) will count the number of faults.
In this mode the filter will flush continuously.
AUTOMATIC OPERATION
CONTINUOUS OPERATION
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
INTERVAL CHANGING INSTRUCTIONS:
1. At normal operation the PLC displays the time, date and I/O table (FIG.1)
2. To change and read parameters press Menu/OK – the following screen will show
(FIG. 2). Use the up/down arrow to reach the PARAMETER (it will blink) and
press Menu/OK.
CHANGING PARAMETERS ON THE PLC
FIG.1
FIG.2
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
3. The following screen will show (FIG. 3)
4. Use the up (∧) arrow till the following screen will show (FIG. 4)
5. Push the left key (<), the time value will start blinking. Use the up (∧) and down
(∨) keys to change the time interval (hours: minutes).
6. Press Menu/OK to confirm changes the following screen will show (FIG. 5).
Select YES by using up (∧) and down (∨) keys and confirm by pressing Menu/OK.
FIG.3
FIG.4
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
MASTR./ SLAVE CHANGING INSTRUCTIONS:
Another change - required only on first use (installation) - is C1:
− If operated as single filter or master filter in cascade – P=00001 (MSTR).
− If operated as slave filter in cascade – P=00002 (SLAVE)
• On main menu (FIG 1) press Menu/OK
• On the menu shown in (FIG 2) press down arrow to reach the PARAMETER
(it will blink) and press Menu/OK.
• Press up (∧) arrow to choose C1 (FIG 6).
• Press Right (>) arrow until the value (P=0001) will blink, and change it by
using the vertical [up (∧) or down (∨)] buttons.
FIG.5
FIG. 6 FIG. 7
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
P=00001 – MASTER. (FIG 6)
P=00002 – SLAVE. (FIG 7)
• Press Menu/OK to confirm changes the confirm screen will show (FIG. 5).
• Select YES by using up (∧) and down (∨) keys and confirm by pressing
Menu/OK.
• Press Menu/OK to return to main screen.
GENERAL DATA
When the PLC is on the main screen (FIG 1), pressing one of the keys below the
numbers: 2, 3, 4 will show one the following data:
2 INTERVAL Time between last flushing cycle to following flushing cycle
(interval) h : m
3 FAULT Number of faults. (Counter)
CTMR Number of flushing cycles due to timer (Counter). 4
CDP Number of flushing cycle due to pressure difference (Counter).
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
The fault condition (RED light on) is generated in following cases:
1. If the two motor limit switches are pressed simultaneously (or both are shorted).
2. The motor works continuously for more than 60 seconds without stopping.
Turn the command switch to RESET (spring loaded) to eliminate FAULT
continuation. RED light should turn off.
Check always the reason for the FAULT.
FAULT
RESET
CONTROLS
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EXTERNAL
Lights : YELLOW - Flushing
RED - Malfunction Command Switch: RESET – (Exit fault mode)
AUTO – (Automatic Operation)
CONT.– Continuous Flushing
Yellow Button: TEST – Manual Flush
INTERNAL
PLC : Programmable Logic Controller, for
service personnel ONLY.
Counter : For monitoring the number of flushings
See PLC instructions.
D.P. - differential pressure switch gage
The D.P. monitors the differential pressure of the filter at
inlet/outlet, to activate the PLC for a single back-flushing cycle.
PLC - control
The PLC activates a single flushing cycle when either the DP or
time is activated
DP is set to 6 psi ,0.4bar, the time is set to 3 hrs. (normally 3-8
hours).
The PLC may be in CONTINUOUS mode - the Timer is then by-passed .
For details of control modes, see the operating modes.
NOTE: before installing bolts back to their places spread the bolts treads with
grease.
1. Every 1 month apply MOLYKOTE G-n Plus Paste to the screw of the drive
assembly (item 17 on breakdown drawing).
2. Every 1 month apply “DOW CORNING 4” or EQUAL grease to the shaft
extension (item 15 on breakdown drawing).
3. Repair any damage to the protective coating of the filter without delay. Prior to
application of protective paint, thoroughly clean the damaged spot with wire
brush.
CONTROL BOX
MAINTENANACE
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
4. In case that there is needs to take out the screen for maintenance, prior to
installation lubricate the screen seals and the cover gasket with “DOW
CORNING 4” or EQUAL grease.
OdisMatic® Filter Check
(Refers to drawing D-C863-001-04 on page 19)
NOTE: before installing bolts back to their places spread the bolts treads with
grease.
• Close filter’s inlet and outlet valves, wait until the pressure is reduce to ‘0’.
• Open drainage valve located on the inlet chamber bottom, and wait until the
water stops to flow.
• Open flushing chamber service port cover (9).
• Dismantle the drive protection cover (13).
• Dismantle the drive pin (22) split pin and pull out the drive pin.
• Open cover (32), verify that cover gasket (28) is intact.
• Pull out the collector assembly and then pull out the filters assembly.
• Verify that filters coarse (3) and fine (4.1) screens are intact.
• Verify that screen seals (4/2) are intact.
• Check that collector (2/2) and suction nozzles (2/3) are intact.
• Verify that screen seals are in there place, lubricate the screen seals with
“DOW CORNING 4” or EQUAL grease; Insert the screens assembly and
then the collector assembly into the filters body.
• Verify that cover gasket (28) is in its place, lubricate the gasket with “DOW
CORNING 4” or EQUAL grease, close cover (32) and tighten the cover bolts.
Before installing bolts back to their places spread the bolts treads with thin
layer of grease.
• Use the service port (29) to install the collector assembly.
• Close flushing chamber service ports cover (9); verify that gasket (29) is in its
place.
• Connect the shaft extension (15) to the drive shaft (17) Install the drive pin (22)
and secure the pin with split pin.
• Install the drive protection cover (13).
• Gradually open filter’s inlet and outlet valves and check for leakage.
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
Item Problem Check If Solution
1 System
does
not work
Power
Main switch OFF Check Main Switch is ON
Check Power supply is available
(electricity).
Check Fuses/overload
2 Fault Lamp ON Check for possible reason - remedy
then press RESET
3 No water
flowing
Isolation
Valve
not open Open then press RESET
Manual
Valves
those required to
be open are not
open
Open them
4 Flowrate
is low or
Outlet
pressure is
low.
Water
pressure
(inlet) or
Line pressure
Pressure is Low
(usually below
35psi),
Press Manual Flush button: TEST
(when all required valves are open).
Increase pressure to normal:
�Water company
�Pumps
�Remote valves
�Main Line blocking
Normal
Go to next line
5 Pressure
drop too
high
Pressure drop
on filter -
difference in
readings of
pressure gage
D.P. is high,
over 0.5 bar, (7
psi).
Press TEST: Manual Flush button.
(on panel).
6 D.P. remains high Check flow rate - if not excessive
(higher than design flow rate).
TROUBLE SHOOTING
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
Item Problem Check If Solution
7 Repeat the above mentioned (Manual
Flush) and if D.P. is high:
a - Check for any
- disconnected or leaking control
tubes.
� disconnected wires
b – Unusually high dirt load
beyond design- call service
meanwhile reduce flow rate.
c – Unusual Blocking of filter
(close isolation valves)
dismantle filter and clean
screens .
8 Flush
valve does
not close
dirt on the
valve’s seat
Dirty Close water entry - release pressure
and clean.
9 Flush
valve does
not open
Solenoid
valve lamp
light not ON
Wiring problem
Replace solenoid if Faulty.
10 Gear
motor
rotating
but Drive
Shaft not
advancing
At extremity of
travel (left or
right) and drive
pin is in place
Check that the Limit Switches are
operating:
a) they are properly positioned
b) wiring problem
c) press on Limit Switch and see if
activated.
Replace Limit Switch if faulty .
Drive nut drive pin is not in
place
Install pin in its place and fit split pin
11 Flush
cycles are
too
frequent
Raw water Dirt load is high
or very soft and
“sticky”
Go to CONTINUOUS MODE
(Command Switch: CONT.).
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
OdisMatic® - 863 - Parts breakdown
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
OdisMatic® - 863
PART LIST (refer to drawing D-C863-001-04– issue 1)
NO DESCRIPTION 86302
86303
86304
86306
86308
86310
86312
86314
1 Filter Body A86302N-SA-2”
A86303F-SA-3”
A86304 F-SA -4”
A86306 F-SA -6”
A86308-8”
A86310-10”
A86312F-SA -12”
A86314F-SA -14”
2 Dirt Collector ass. E8632021 E8632041 E86302081 E8632121
2/1 Collector bearing E86002060 E86002060 E86002060 E86002060
2/2 Collector Body E8632022 E8632042 E86302082 E8632122
2/3 Suction Nozzle assy. E8632211 E8632211 E8632811 E8632811
2/3-1 Suction Nozzle pipe E8632212 E8632212 E8632812 E8632812
2/3-2 Suction Nozzle E8632213 E8632213 E8632213 E8632213
Suction nozzle "O" ring ER00106 ER00106 ER00106 ER00106
3 Coarse Screen E86302020 E86304020 E86308020 E86312020
4 Fine Screen ass. E86302030 E86304030 E86308030 E86312030
4/1 Fine screen E86302031 E86304031 E86308031 E86312031
4/2 Fine screen seal E263003 E263003 E8628000 E8628000
4/3 Collector lower guide E86007060 E86007060 E86007080 E86007080
4/4 Guide Base E86302033 E86302033 E86308033 E86308033
4/5 Guide Stopper ER00113 ER00113 ER00113 ER00113
5 Electrical Board E86336060 E86336060 E86336060 E86336060
6 Solenoid Valve – N.O N512009 N512009 N512009 N512009
7 3 way valve PM202500 PM202500 PM202500 PM202500
8 Pressure Gauge N6111025 N6111025 N6111025 N6111025
9 Service port Cover E400260-SFR E400260-SFR E400260-SFR E400260-SFR
10 Flush valve NB20501502T NB20501502T NB470863020T NB470863020T
11 Drive base support E86302040 E86302040 E86308040 E86308040
12 Shaft Seal (set) E86302162 E86302162 E86302162 E86302162
13 Drive protection cover E86010060 E86010060 E86010060 E86010060
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
OdisMatic® - 863
PART LIST (refer to drawing D-C863-001-04– issue 1)
NO DESCRIPTION 86302
86303
86304
86306
86308
86310
86312
86314
14 Limit switch N598605 N598605 N598605 N598605
15 Shaft Extension E86022060 E86022060 E86022060 E86022060
16 Limit switch disk E86024060 E86024060 E86024060 E86024060
17 Drive shaft E86012060 E86012060 E86012060 E86012060
18 Worm gear motor V5397 V5397 E86035060 E86035060
19 Drive shaft cover E86026060 E86026060 E86026060 E86026060
20 Drive key E86025060 E86025060 E86025060 E86025060
21 Disk positioning nut E86011060 E86011060 E86011060 E86011060
22 Drive pin E86023060 E86023060 E86023060 E86023060
23 Drive base E86021060 E86021060 E86021060 E86021060
24 Drive nut E86020060 E86020060 E86020060 E86020060
25 Shaft guide E86302041 E86302041 E86302041 E86302041
26 Air valve N131010 N131010 N131120 N131120
27 Guide seal E86302043 E86302043 E86302043 E86302043
28 Cover gasket ER02004 ER02004 ER10033 ER10033
29 Service port gasket E004365 E004365 E004365 E004365
30 D.P switch N6040 N6040 N6040 N6040
31 Collector guide E86015060 E86015060 E86015080 E86015080
32 Cover E86302050 E86302050 E86308050 E86308050
33 Drain valve PM1075110 PM1075110 PM1075110 PM1075110
34 Pressure Control Box Y8510201 Y8510201 Y8510201 Y8510201
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
3x380VAC
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
3x220VAC
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz
User’s Notes
EuroClean s.r.o. Podbabská 81 /17, Praha 6 , PSČ: 160 00 IČO: 26141477, DIČ: CZ26141477
Tel.: 224 811 900, Fax: 224 810 597, e-mail: [email protected], web: www.euroclean.cz