1-30-2020 Page 1 o f 3

813P, 833P APPLICATOR QUICK SETUP GUIDERefer to Operators Manual for Complete Setup Instructions

Set Up Tractor Hydraulics - All MachinesImportant: Check hydraulic oil level. Fill if necessary. Set SCV flow rates and detent times as shown in table.

SCV Function Flow Detent TimeI Main Lift Wing Kick 5 ContinuousII Main Fold 12 ContinuousIII

Pump 8Continuous

IVFlip Fold 5

Continuous

Unfolding the Toolbar -- from Transport Position to Field Position• Push SCV I forward to lower the main wing.• Push SCV II forward to unfold main wings down from transport to field position.• This remote must be left in the FLOAT position during field application to allow the main wings to flex up

and down. Not the centered (neutral) position.• Push SCV III forward to unfold flip wings down into field position.

Folding the Toolbar -- from Field Position into Transport Position• Pull rearward on SCV I to raise the main wing.• Pull SCV II backward to fold flip wings up into transport position.• Push SCV III all the way forward into FLOAT mode to fold the main wings up into transport position.

https://www.youtube.com/watch?v=YCYqRj-eGlA

1-30- 2020 Page 2 o f 3

Adjust Center Section Height• Place machine on level surface in field• Unfold toolbar and lower until coulter blades are 2-4” in the

ground• Install required number of depth stops (A) on main lift

cylinders to set the center section to desired depth• While applying fertilizer, operate SCV I in continuous down

mode. This will keep the center section against the depthstops and supply oil to the down pressure valve(s)

Adjust Gauge Wheel Height• With center section height set, adjust the inner and outer gauge

wheels so that the coulter blades are 2-4” in the ground• Adjust gauge wheel (B) by removing spring clip (D) and retaining

pin (C) and moving the gauge wheel up or down• Reinstall pin and retaining clip

Set Toolbar Main Wing and Flip Wing Down-Pressure (If Equipped)Important: Toolbar down pressure should read between 700 - 1000 psi but can be adjusted from 0 - 1500psi. Down pressure should not exceed 1500 psi. Do not use more down-pressure than necessary or excessive wear and damage to machine could result.

• Adjust down-pressure to initial setting by turning the socket • head screw on the down pressure valve. Tighten to increase

pressure, loosen to decrease pressure.• Once set, lock screw in position with jam nut.• Make a trial pass in field. If coulter to ground engagement is

not satisfactory, adjust hydraulic pressure as needed• If equipped, use Flip Wing down pressure valve in the same manner to adjust Flip Wing down

pressure.

Product Plumbing Setup and Calibration• Refer to Operators Manual for complete product plumbing setup, calibration, and servicing.

813P

AN

D 8

33P

DO

UB

LE

BA

R T

RA

CT

OR

RE

MO

TE

FU

NC

TIO

NS

Qui

ck R

efer

ence

She

et

TR

AC

TO

R R

EM

OT

E #

1

TR

AC

TO

R R

EM

OT

E #

2

TR

AC

TO

R R

EM

OT

E #

3

1)Lo

wer

s the

mai

n w

ing

kick

func

tion

1)U

nfol

ds m

ain

win

gs d

own

from

trans

port

to fi

eld

posi

tion

2)Th

is re

mot

e m

ust b

e le

ft in

the

float

posi

tion

durin

g fie

ld a

pplic

atio

n to

allo

w th

e m

ain

win

gs to

flex

up

and

dow

n. N

ot th

e ce

nter

ed (n

eutra

l)po

sitio

n.1)

Unf

olds

flip

win

gs d

own

into

field

pos

ition

1)K

icks

the

mai

n w

ings

up

1)Fo

lds m

ain

win

gs u

p in

totra

nspo

rt po

sitio

n1)

Fold

s flip

s win

gs u

p in

totra

nspo

rt po

sitio

n

1-30- 2020 Page 3 o f 3

Slide Number 1Slide Number 2