802.11ac WIFI Fundamentals
-
Upload
criterion123 -
Category
Engineering
-
view
369 -
download
9
Transcript of 802.11ac WIFI Fundamentals
A strong Wi-Fi evolution path
WiFi evolution path is as following[41] :
802.11ac Technology Overview
5 GHz supported
Even wider channels (80 MHz and 160 MHz)
Higher order modulation (256-QAM)
Beam forming (explicit)
Backwards compability with 11a/b/g/n [16]
80 MHz is contiguous and 4.5x faster than 20 MHz
160 MHz can be either contiguous or in two non-contiguous
80 MHz slices
Channel Allocations
Wave 2
What will wave 2 802.11ac deliver?
MU-MIMO: Transmit data to multiple devices simultaneously
VHT160 : Doubles max data rate[16] Type Data Rate (Mbps)
11n 3x3 HT40 450
11ac 3x3 VHT80 1300
11ac 4x4 VHT160 3467
802.11ac: Up to 3x increase in throughput per stream
3x more in the future with MU-MIMO[41] :
Sub-carriers
OFDM subcarriers used in 802.11a, 802.11n and
802.11ac [16]
QAM constellations
Constellation diagrams for 16-, 64-, 256-QAM [16]
Data Rate
11n and 11ac data-rate Table[8]
802.11ac: Higher data rates at all ranges
With the identical throughput, 802.11ac has longer
transmission distance than 802.11n[41].
Block Diagram
Block diagram[16] :
DAC
A Digital-to-Analog converter(DAC) generates the
sampled output using the sampling clock from the
synthesizer or clock distribution chip.
Hence, the sampling clock quality is direct correlation
of the sampled DAC output performance[17].
Besides, due to the limited number of bits in a practical
DAC, there will be quantization noise, which is not
affected when the TX power is reduced[16]
DAC
Clock signal with high Noise Spectrum Density(NSD) in
spectrum turns to waveform with jitter, and vice
versa[17].
DAC
NSD in spectrum (jitter in waveform) leads to EVM issue
due to phase error.
In addition, it leads to Adjacent Channel Power
Ratio(ACPR) issue as well[19].
Am
plit
ud
e
Adjacent
Channel
Channel
Separation
frequency Phase noise
DAC
DAC can be seen as a clock divider plus a mixer. The
clock and its noise enter the divider together, and then
the divider output mixes with signal source to form the
DAC output[17].
DAC acts like a divider, dividing the clock frequency
and therefore lowers the clock phase noise.
DAC
The following equation illustrates how clock noise
performance is improved by DAC[17].
DAC
According to the equation, we know :
The lower the clock NSD is, the lower DAC output NSD will
be.
The lower DAC output frequency is, the lower DAC output
NSD will be.
The higher clock frequency is, the lower DAC output NSD
will be.
DAC
According to measurement, it proves again that the
lower DAC output frequency is, the lower DAC output
NSD will be.
Besides, the DAC output noise should be a
combination of clock noise and DAC intrinsic noise.
DAC
According to measurement, it proves that the lower
DAC output frequency is, the lower DAC intrinsic noise
will be[17].
DAC
SNR can be derived as:
Take 256 QAM for example, the EVM requirement is
2.5%, then SNR is 32 dB.
DAC output NSD limit can be derived as:
Hence, we take 256 QAM(SNR = 32 dB), BW = 80 MHz
for example, the DAC output NSD should NOT be larger
than : -32 – 79 = -111(dBc/Hz)
Besides, in order to meet EVM requirement, the wider
the bandwidth is, the lower the DAC output NSD should
be. Because wider bandwidth contributes to more
stringent DAC output NSD requirement.
DAC
As mentioned above, the relationship between DAC
output NSD and clock NSD is :
Thus, the clock NSD should NOT larger than -97(dBc/Hz)
Assuming fclock is 983.04 MHz, and fDAC_Output is 200 MHz,
we are capable of deriving clock NSD requirement as :
DAC
As mentioned above, NSD in spectrum (jitter in
waveform) leads to EVM issue due to phase error.
The measurement is as following :
From the measurement, it proves again that the higher
the clock jitter is, the higher the EVM will be[17].
DAC
The influence of peaking NSD and average NSD is
shown below. If the clock NSD is lower than the
predicted value, then the DAC EVM specification can be
met. If there is some peaking in clock phase noise
curve, then the DAC EVM may fluctuate and the
fluctuation depends on the peaking power[17].
DAC
With channel bandwidth = 80 MHz, the spectrum mask
specification is as following:
A (0 dBc, @ 39 MHz offset)
B (20 dBc, @ 41 MHz offset)
C (28 dBc, @ 80 MHz offset)
D (40 dBc, @ 120 MHz offset)
Basically, spectrum mask is just wideband ACPR, which
is related to NSD of DAC output and clock.
DAC
Hence, the NSD of DAC output and clock should be as
low as possible to meet spectrum mask specification.
fclock fDAC DAC
DAC
B (20 dBc, @ 41 MHz offset) Take point B for example, the NSD
of DAC output can be derived as :
With channel bandwidth = 80 MHz, assuming the ACPR
requirement is 70 dBc, then
-70 - 10*log(80MHz) = -149 dBc/Hz
Thus, @ 41 MHz from fDAC_output , the NSD of DAC output
should NOT be larger than -149 dBc/Hz to meet
Spectrum mask requirement.
DAC
B (20 dBc, @ 41 MHz offset) Again, take point B for example,
the NSD of clock can be derived
as :
Thus, @ 41 MHz from fClock , the NSD of clock should
NOT be larger than -135 dBc/Hz to meet Spectrum mask
requirement.
OFDM
Orthogonal Frequency Division Multiplexing, OFDM, is
frequently referred to as multi-carrier modulation
because it transmits signals over multiple subcarriers
simultaneously.
It is based on the Fast Fourier transform (FFT) concept,
which allows the multiple subcarriers to overlap yet
maintain their integrity[20].
OFDM
Over a long transmission distance, the signal passes
through a variety of physical mediums. As a result, the
actual received signal contains the direct path signal
overlaid with signal reflections of smaller amplitudes.
This is called multipath.
OFDM
Multipath makes received signal slightly distorted. The
direct path signal arrives as expected, but slightly
attenuated reflections arrive later. These reflections
interfere with subsequent symbols transmitted along
the direct path.
Thus, multipath causes Inter Symbol Interference(ISI)
because the reflections will make up a significant
percentage of the symbol period. This problem
becomes much more significant at high symbol
rates[21].
OFDM
OFDM systems mitigate this problem by utilizing a
longer symbol period, which doesn’t sacrifice throughput by utilizing multiple sub-carriers per
channel[21].
OFDM
In addition, high throughput are achieved in OFDM due
to precise carrier spacing and exact amplitude and
phase settings for each individual carrier constellation.
This is accomplished using computational modulation
schemes rather than traditional analog modulation[20].
Given the fact that the multiple subcarrier spectrum can
overlap as long as they are orthogonal, Spectrum
efficiency can be improved. As mentioned above, the
modern OFDM systems are FFT/IFFT based[34].
RX
OFDM
Spectrum of FFT based OFDM Signal (Digital)[34] :
OFDM
However, in terms of RF section, OFDM design face
several key issues, including power consumption,
linearity, phase distortion and phase noise. These
issues will impact throughput.
OFDM
One of the most difficult engineering concerns in the
RF section of is handling very large peak-to-average
power ratios (PAPRs). A peak in the signal power will
occur when all, or most, of the sub-carriers align
themselves in phase. In general, this will occur once
every symbol period[20-22].
Average Power
Peak Power
Time
OFDM Symbol Power
OFDM
The value of the PAPR is directly proportional to the
number of carriers, and is given by:
where N is the number of carriers[20].
Besides, the more number of subcarriers, the wider the
bandwidth will be. In other words, PAPR is proportional
to bandwidth as well. 802.11ac
Bandwidth Number of
subcarriers
(IFFT Size)
20 MHz 64
40 MHz 128
80 MHz 256
160 MHz 512
OFDM
For example, for the 802.11a OFDM standard, if the
phases of all 52 carriers line up simultaneously during a
symbol period, the PAPR will be 17 dB, let alone
802.11ac because the higher order modulation leads to
higher PAPR[20].
If the peak power is larger than PA’s compression point, the signal will be clipped, resulting in distortion and
nonlinear effect[23].
OFDM
Given the fact that the clipped waveform is like square
waveform, which is rich in harmonics[42].
Thus, in terms of waveform, it illustrates that why
clipping distortion produces harmonics. The more
serious the clipping distortion is, the larger harmonics
there will be.
OFDM
In order to achieve the desired linearity at the PA output,
the PA must be operated with significant backoff from
its saturation point. The larger the PAPR is, the more
backoff should be[24].
OFDM
With desired linearity, in terms of PA’s efficiency, the more backoff leads to lower output power, which
results in lower efficiency.
Maximum power efficiency of a Class B PA is 78.5%.
Nevertheless, when accounting for a signal having a
PAPR of 10 dB, this efficiency drops to 7.85 %[20]
OFDM
Thus, for 802.11ac, due to its wide bandwidth and high
order modulation, PAPR is large, and this leads to high
linearity requirement and high DC power
consumption[20].
High DC power consumption leads to thermal issue,
which aggravates PA’s linearity and results in EVM and spectrum mask issue[25].
PA
OFDM
Therefore, add GND vias in thermal pad as many as
possible to mitigate thermal issue, thereby improving
RF performance.
Linearity Concerns
OFDM modulation is also very sensitive to the inter-
modulation distortion (IMD) that results from mild non-
linearity in the RF section. Because the subcarriers are
equally spaced, the third-order IMD will appear exactly
on top of another carrier.
Power
Frequency
OFDM Carriers
IMD3 interference
These IMD interference will contribute to a noise-like
cloud surrounding each constellation point[20].
Linearity Concerns
For higher-level modulations, these constellation
clouds can contribute to an increase in bit errors for
each carrier. Even a modest increase in bit error rate
(BER) for each carrier can result in a dramatic increase
in the cumulative error rate over a packet.
As shown below, the larger the IIP3 is, the lower IMD3
interference will be[26].Thus, in an OFDM design,
enough linearity is necessary [20].
Linearity Concerns
In terms of TX performance, a noise-like cloud
surrounding each constellation point leads to EVM
issue.
In terms of RX performance, an increase in symbol
error rate decreases SNR, thereby aggravating
sensitivity.
Linearity Concerns
For the receiver, the power levels are much lower but
the linearity requirement is even more challenging. This
arises from the possible presence of adjacent
channel interference from other, independent but
closely located, WLAN networks[20].
WiFi
Terminal
WiFi
Terminal
WiFi
Terminal
RX
Desired TX
Undesired TX
Because the possibility of the interfering transmitter
location being nearer than the desired transmitter, the
adjacent channel blocker is often received with a
significantly stronger signal power level than the
desired channel. Power
Frequency
Desired TX
Undesired TX
Linearity Concerns
The strong blocker may saturate LNA, leading to gain
reduction. The stronger the blocker is, the more gain
reduction will be[27].
Gain
Blocker Power
Linearity Concerns
According to Friis Formula :
lower gain leads to higher noise figure, thereby
aggravating sensitivity[27].
Gain
Frequency
Noise Figure
Linearity Concerns
But, actually, an infinite gain increment does NOT lead
to an infinite noise figure reduction.
Besides, an infinite gain increment does lead to an
infinite IIP3 reduction. As mentioned above, with
blocker, poor linearity leads to poor sensitivity as
well[28].
LNA Gain V.S Cascade Noise Figure & IIP3
IIP3
NF
Linearity Concerns
Thus, in order to achieve desired sensitivity, the
linearity is the larger the better.
But the gain is neither the larger the better nor the
smaller the better. It is the more exact the better.
LNA enabled Bypass Mode
Gain (dB) 12 -7
IIP3 (dBm) 4 20
Take SKYWORKS SKY85608-11 for example, the gain
and IIP3 are 12 dB and 4 dBm respectively while
activating LNA.
With bypass mode, the IIP3 increases to 20 dBm. It
proves again that LNA’s gain is a compromise between
linearity and noise figure[29].
Phase Noise
By definition, multi-carrier modulation requires very
close proximity of the adjacent individual carriers. This
is possible due to the relatively low data rate for each
carrier.
However, upon down-conversion in the receiver, any
phase noise associated with the local oscillator (LO)
synthesizer will be superimposed onto the low data rate
modulation[20].
Frequency
Power
LO with phase noise
OFDM Carriers
Frequency
Power
Down-converted
OFDM Carriers
With LO phase noise
Phase Noise
As a result, making LO phase noise level sufficiently
low becomes extremely important to achieve low BER
in an OFDM design[20].
Otherwise, as in the case of IMD, a modest increase in
the BER for each carrier can result in a dramatic
increase in the symbol error, thereby aggravating
sensitivity[20].
Phase Noise
Take Broadcom BCM4359 for example, these areas
marked red should be kept out, because these areas are
VCO related circuits[30].
Otherwise, the parasitic effect will aggravate
the phase noise.
Phase Noise
The phase noise of an on-chip VCO will dominate, due
to the low Q of its spiral inductors[20,31].
Nevertheless, the phase noise of crystal(XTAL) also
matters. With poor phase noise of XTAL, the VCO phase
noise aggravates as well[20].
BCM4359
XTAL, 37.4 MHz
XTAL with phase noise
Phase Noise
Besides, we ought to care the power traces related to
VCO, PLL, LO, and synthesizer very much because they
affect phase noise as well[32].
According to the formula below, the lower the IDD is, the
larger the phase noise will be. Thus, the IR drop should
be as low as possible.
Phase Noise
If the input signal is interfered by high frequency noise,
the output signal will has spurs[32].
Hence, keep noisy traces away from XTAL and VCO
power trace.
In addition, reserve bypass capacitor for these power
pins and the location of bypass capacitor should be as
close to chip as possible.
Phase Noise
If the voltage of VCO has large ripple, the phase noise
aggravates as well. Thus, as in the case of bypass
capacitor, reserve decoupling capacitor for these power
pins and the location of decoupling capacitor should be
as close to chip as possible[32].
Time
Voltage Ripple
As shown below, the larger the decoupling capacitor
value is, the lower phase noise will be.
Phase Noise
As mentioned above, the poor power supply
contributes to large phase noise and spurs. Thus, we
can use a clean external power supply to check the root
cause of poor phase noise[32].
Offset Frequency(Hz)
Ph
as
e N
ois
e (
dB
c/H
z)
Poor Power Supply
Clean Power Supply
PA
Constant envelope signal : shape of spectrum
unchanged.
Constant Envelope
Variable Envelope
Variable envelope signal : shape of spectrum manifest
as noise like shoulders, known as spectral regrowth.
For every one 1 dB drop in TX power, the regrowth
drops by 3 dB(2 dB net)[16].
PA
Given the fact that OFDM has high PAPR, the peaks in
the OFDM signal cause distortions[16].
Thus, as mentioned above, the PA must be operated
with significant backoff from its saturation point to
achieve desired linearity[33].
PA Non-linearity
PCIe
According to Shannon Theorem :
We know that channel capacity is proportional to SNR.
SNR(dB)
Data Rate
(Mbps/MHz)
In terms of TX, the higher SNR is, the lower EVM will be.
SNR(dB)
EVM
(%)
SNR(dB)
BER
(%)
In terms of RX, the higher SNR is, the lower BER will be,
which leads to better sensitivity.
PCIe
Thus, both lower EVM and better sensitivity will lead to
higher throughput.
However, take Broadcom BCM4359 for example, the PCIe
interface between BCM4359 and Baseband chip affects
throughput as well. So we also need to take care of it
circumspectly.
BCM 4359
PCIE _ REFCLK _ P
PCIE _ REFCLK _ N
PCIE _ T X _ N
PCIE _ RX _ P
PCIE _ RX _ N
PCIE _ T X _ P
Baseband Chip
When placing series components on these lines, select
component sizes such that pads have a width similar to the
PCIe line. Doing this will reduce reflections from impedance
mismatches.
PCIe
As shown above, there are three PCIe differential pairs, and
their impedance should be 100Ω.
In each pair, match the lengths of each pair member to less
than 30 mils.
Impedance Discontinuity
Reference
[1] CHALLENGES IN DESIGNING 5 GHZ 802.11AC WIFI POWER AMPLIFIERS, RFMD
[2] WCN3660 EVM Degradation Issue Technical Note, Qualcomm
[3] SE5516A: Dual-Band 802.11a/b/g/n/ac WLAN Front-End Module, SKYWORKS
[4] 802.11ac Technology Introduction White Paper, RHODE & SCHWARZ
[5] WLAN IEEE 802.11ac Wide bandwidth high speed 802.11ac technology and testing,
RHODE & SCHWARZ
[6] ACPF-7024 ISM Bandpass Filter (2401 – 2482 MHz), AVAGO
[7] WCN36x0(A) RF Matching Guidelines, Qualcomm
[8] MCS Index for 802.11n and 802.11ac Chart
[9] Sources of Error in IQ Based RF Signal Generation
[10] Integration Aids 802.11ac Mobile Wi-Fi Front Ends
[11] Mini filters for multiband devices, TDK
[12] QCA61x4-1 RF Matching Guidelines, Qualcomm
[13] QCA61x4, QCA937x, QCA65x4 Design Guidelines/Training Slides, Qualcomm
[14] QCA6164-1 with External 2.4G and 5G RFFM Reference Design Example, Qualcomm
[15] WLAN/BT/FM Training Using WCN3660, WCN3660A, or WCN3680, Qualcomm
[16] 802.11ac Wi-Fi Fundamentals
[17] Effects of Clock Noise on High-Speed DAC Performance, Texas Instruments
[18] DIGITAL-TO-ANALOG CONVERTER ICs, Analog Devices
[19] Optimizing the Stimulus to Maximize System Performance
[20] The OFDM Challenge
[21] OFDM and Multi-Channel Communication Systems, National Instruments
[22] 4G Broadband-what you need to know about LTE
[23] Wideband Digital Pre-Distortion Modeling for LTE-Advanced, Keysight
[24] Linearize Power Amps With RF Predistortion
[25] Wideband High Dynamic Range Limiting Amplifier
[26] IMD Measurement with E5072A ENA Series Network Analyzer, Keysight
[27] SAW-less Direct Conversion Receiver Consideration
[28] Sensitivity or selectivity -- How does eLNA impact the receriver performance
[29] SKY85608-11: 5 GHz, 802.11ac Switch/Low-Noise Amplifier Front-End, SKYWORKS
[30] BCM4359 Printed Circuit Board Layout Guidelines, Broadcom
[31] Designing A Low-Noise VCO
[32] GPS RF FRONT-END CONSIDERATIONS
[33] EXAMPLE: 802_11a_RX_Sensitivity, National Instruments
[34] Fundamentals of OFDM Communication Technology
[35] ADC Input Noise: The Good, The Bad, and The Ugly. Is No Noise Good Noise?
[36] A New Leap Towards True Software-Defined Radio
[37] What are Anti-Aliasing Filters and Why are They Used?, National Instruments
[38] Switched-Capacitor Filters Beat Active Filters at Their Own Game
[39] Agile ADCs Enable Digital Cellular Receivers
[40] NAVIGATE THE AFE AND DATA-CONVERTER MAZE IN MOBILE WIRELESS
TERMINALS, MAXIM
[41] The Wi-Fi Evolution An integral part of the wireless landscape, Qualcomm
[42] VLSI Testing Lectures 13 and 14: Radio Frequency (RF) Testing