8 9 10 11 Side 2 4. Install Drive Carrier Install the PCI...Remove hot-swap drive carrier(s) by...
1
16 Software • BIOS, Drivers, and Operating System Installation A. Confirm BIOS Version: Look on the Server/System Management screen in the BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at: http://www.intel.com/p/en_US/support/highlights/server/s3420gp If new versions are available, update the BIOS on your server. See the Service Guide on the Intel ® Server Deployment Toolkit CD for update instructions. B. Configure your RAID Controller: Use the instructions provided with the RAID controller. C. Install your Operating System: Use the instructions provided with the RAID controller and with the operating system. D. Install Operating System Drivers: With the operating system running, insert the Intel ® Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel ® Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other operating systems, browse the CD folders to locate and install the driver files. Side 2 Install Hard Disk Drives 8 Connector End of Drive 1. Remove the Drive Carrier 2. Install 2.5’ Drive into Carrier 3. Install 3.5” Drive into Carrier 4. Install Drive Carrier into Chassis 5. Hard Drive Numbering Diagram Repeat these steps for each installed hard drive. CAUTION: If you install less than four drives or devices, empty drive bays must be occupied by carriers to maintain proper system cooling. To avoid possible damage to your chassis, use only the carriers that came with your server system. Remove hot-swap drive carrier(s) by pushing the green latch towards the lever, opening the lever all the way, and then pulling the drive carrier out of the system. A Attach drive to carrier from the underside using four screws. Make sure the connector end of drive is placed as shown. A Connector End 2.5” HDD Attach drive to carrier side rails using four screws. Make sure connector end of drive is placed as shown. A 3.5” HDD With the carrier lever in the OPEN position, slide drive assembly into chassis until it fully engages the backplane connector, then close the lever until it snaps shut. A 0 1 2 3 Drive 1 Primary 9 A Remove filler panel from the add-in card slot. Turn PCIe riser assembly up-side-down for this procedure to avoid damage to the riser card connector. B Insert add-in card until it seats into the riser card socket. C Attach with screw as shown. CAUTION: Observe normal ESD precautions when installing the PCIe add-in card. Riser Connector REMOVE Filler Panel A C B Riser Socket Riser Card Install Add-in Card Available Documents Technical Specification Update Quick Reference Label Quick Start User Guide/System Configuration Guide Additional Reference documents available at: http://www.intel.com/p/en_US/support highlights/server/s3420gp Front Panel Controls and Indicators A F E D C B A. Power/Sleep Button B. System Reset Button C. Power/Sleep LED D. System NIC 5 Activity LED E. System Status LED F. USB 2.0 Connectors - Port 0/1 11 Install Intel® SAS module and I/O Expansion Module (Optional) A Refer Intel ® Server System Service Guide, available on the Intel ® Server Deployment Toolkit CD or at vhttp://www/intel/com/support/motherboards/server/s3420gprx, for detailed steps of installation of Intel ® SAS Module and Intel ® I/O Expansion Module. 10 Position riser card edge connector over the server board riser socket and align riser with the back panel opening of the chassis. A Press down uniformly until thePCI riser assembly engages both the chassis back panel and the riser socket on the server board. Check that the assembly is flush with the top edges of the chassis. B PCI Riser Socket Riser Card Edge Connector A B Install the PCI Riser Assembly 12 Install the Air Duct Air Duct 13 Install the Top Cover Captive Thumb Screw Tighten the captive thumb screw after installation. Replacement of shipping screw is optional. A C A B 14 Install Rack Handles 15 Before installing your operating system, you must finish your chassis installation, make I/O connections and plug in power. Finishing Up CAUTION: See your chassis documentation for power and grounding requirements. A. Redundant Power Supply Units B. Power Supply Status LED C. NIC 1 & 2 Connectors RJ-45 D. Video Out E. NIC 3, 4 & 5 Connectors RJ-45 F. Dual USB Ports G. RJ-45 Serial Port H. PCI Express* Add-in Slot I. IO Module External Connectors J. Thumb Screw Back Panel Features and Indicators A. Redundant Power Supply Units B. Power Supply Status LED C. NIC 1 & 2 Connectors RJ-45 D. Video Out E. NIC 3, 4 & 5 Connectors RJ-45 F. Dual USB Ports G. RJ-45 Serial Port H. PCI Express* Add-in Slot I. IO Module External Connectors J. Thumb Screw IMPORTANT NOTE: The Intel ® Server System SR1695GPRX requires the use of shielded LAN cable to comply with Emission/Immunity regulatory requirements. Use of non shield cables may result in product non-compliance. * See your Server Board S3420GP Product Guide for specific capabilities and configurations for server board system fans. Fan1 Fan2 Fan3 See chassis diagram at right for system fan numbering information. To remove fan, first unplug power cable to server board, then lift straight up and remove. When installing new fan, note air flow direction arrow. System airflow is from front to back. Chassis Fan Connections 2 3 1 Air Flow Server System Cabling and Component Diagram ... Quick Reference Front Panel USB HDD 0 HDD 3 HDD 1 HDD 2 Cable Connection Details Serial B USB 6/7 Front Panel IMPORTANT NOTE: See your Intel ® Server System SR1695GPRX Service Guide for complete cabling and server board component descriptions. See your BBU product documentation for complete installation information. Battery Backup Unit Power Supply BBU Optical Drive RAID Card Server Board Front Panel HDD 0 HDD 1 HDD2 HDD3 Front Panel USB Backplane Backplane IPMB SGPIO SES Optical Drive Server Board Power Connections Auxiliary Signal Power Detail Latch CPU Power Connector Detail CAUTION: Note the location of the latch on each power cable connector and align it with the matching tab on each server board socket. Main Power Connector Detail Intel ® Server Board S3420GPRX Component Layout Note: Not all components, jumpers and connectors are described in this diagram. Refer to your Server System Service Guide on the Intel ® Server Deployment Toolkit CD for additional information.
Transcript of 8 9 10 11 Side 2 4. Install Drive Carrier Install the PCI...Remove hot-swap drive carrier(s) by...
16 Software • BIOS, Drivers, and Operating System Installation
A. Confirm BIOS Version: Look on the Server/System Management screen in the BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at:http://www.intel.com/p/en_US/support/highlights/server/s3420gpIf new versions are available, update the BIOS on your server. See the Service Guide on the Intel® Server Deployment Toolkit CD for update instructions.
B. Configure your RAID Controller: Use the instructions provided with the RAID controller.
C. Install your Operating System: Use the instructions provided with the RAID controllerand with the operating system.
D. Install Operating System Drivers: With the operating system running, insert theIntel® Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel®Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other operating systems, browse the CD folders to locate and install the driver files.
Side
2 Install Hard Disk Drives8
Connector End of Drive
1. Remove the Drive Carrier 2. Install 2.5’ Drive into Carrier
3. Install 3.5” Drive into Carrier
4. Install Drive Carrier into Chassis
5. Hard Drive Numbering Diagram
Repeat these steps for each installed hard drive.
CAUTION: If you install less than four drives or devices, empty drive bays must be occupied by carriers to maintain proper system cooling. To avoid possible damage to your chassis, use only the carriers that came with your server system.
Remove hot-swap drive carrier(s) by pushing the green latch towards the lever, opening the lever all the way, and then pulling the drive carrier out of the system.
AAttach drive to carrier from the underside using four screws. Make sure the connector end of drive is placed as shown.
A
Connector End
2.5”HDD
Attach drive to carrier side rails usingfour screws. Make sure connectorend of drive is placed as shown.
A
3.5”HDD
With the carrier lever in the OPEN position, slide drive assembly into chassis until it fully engagesthe backplane connector, then close the lever until it snaps shut.
A
0 1 2 3Drive 1 Primary
9
A Remove filler panel from the add-in card slot.
Turn PCIe riser assembly up-side-down for this procedure to avoid damage to the riser card connector.
B Insert add-in card until it seats into the riser card socket.
C Attach with screw as shown.
CAUTION:Observe normal ESD precautions wheninstalling the PCIe add-in card.
Riser ConnectorREMOVE Filler Panel
A
C
B
Riser Socket
Riser Card
Install Add-in Card
Available DocumentsTechnical Specification UpdateQuick Reference LabelQuick Start User Guide/System Configuration Guide
Additional Reference documents available at:http://www.intel.com/p/en_US/supporthighlights/server/s3420gp
Tab
Front Panel Controls and Indicators
A FED
CB
A. Power/Sleep ButtonB. System Reset ButtonC. Power/Sleep LEDD. System NIC 5 Activity LEDE. System Status LEDF. USB 2.0 Connectors - Port 0/1
11 Install Intel® SAS module andI/O Expansion Module (Optional)
A Refer Intel® Server System Service Guide, available on the Intel® Server DeploymentToolkit CD or at vhttp://www/intel/com/support/motherboards/server/s3420gprx,for detailed steps of installation of Intel® SAS Module andIntel® I/O Expansion Module.
10
Position riser card edge connector over the serverboard riser socket and align riser with the back panelopening of the chassis.
A
Press down uniformly until thePCI riser assemblyengages both the chassis back panel and the risersocket on the server board. Check that the assembly is flush with the top edgesof the chassis.
B
PCI RiserSocket
Riser CardEdge Connector
AB
Install the PCIRiser Assembly
12 Install the Air DuctAir Duct
13 Install the Top CoverCaptiveThumbScrew
Tighten the captive thumb screwafter installation. Replacement ofshipping screw is optional.
A
C
A
B
14 Install RackHandles
15Before installing your operating system, you must finish your chassis installation, make I/O connections and plug in power.
Finishing Up
CAUTION: See your chassisdocumentation for power and grounding requirements.
A. Redundant Power Supply UnitsB. Power Supply Status LEDC. NIC 1 & 2 Connectors RJ-45D. Video OutE. NIC 3, 4 & 5 Connectors RJ-45 F. Dual USB PortsG. RJ-45 Serial Port H. PCI Express* Add-in SlotI. IO Module External ConnectorsJ. Thumb Screw
Back Panel Features and Indicators
A. Redundant Power Supply UnitsB. Power Supply Status LEDC. NIC 1 & 2 Connectors RJ-45D. Video OutE. NIC 3, 4 & 5 Connectors RJ-45F. Dual USB PortsG. RJ-45 Serial Port H. PCI Express* Add-in SlotI. IO Module External ConnectorsJ. Thumb Screw
IMPORTANT NOTE: The Intel® Server System SR1695GPRXrequires the use of shielded LAN cable to comply withEmission/Immunity regulatory requirements. Use of non shieldcables may result in product non-compliance.
* See your Server Board S3420GP Product Guide for specific capabilities and configurations for server board system fans.Fan1 Fan2 Fan3
See chassis diagram at right for system fan numbering information.To remove fan, first unplug power cable to server board, then lift straight up and remove.When installing new fan, note air flow direction arrow. System airflow is from front to back.
Chassis Fan Connections
23
1
A i r F l o w
Server System Cabling and Component Diagram ... Quick Reference
FrontPanelUSB
HDD 0 HDD 3
HDD 1
HDD 2
Cable Connection Details
Serial B
USB 6/7
Front Panel
IMPORTANT NOTE: See your Intel® Server System SR1695GPRXService Guide for complete cabling andserver board component descriptions.
See your BBU productdocumentation for complete installation information.
BatteryBackupUnit
PowerSupply
BBU
OpticalDrive
RAID
Car
d
ServerBoard
Fron
t Pan
el
HDD
0
HDD
1
HDD2
HDD3
Front Panel USB
Backplane
Backplane
IPM
B SGPIO
SES
OpticalDrive
Server Board PowerConnections
Auxiliary SignalPower Detail
Latch
CPU PowerConnector Detail
CAUTION: Note the location of the latch on each power cable connector and align it with the matching tab on each server board socket.
Main PowerConnector Detail
Intel® Server Board S3420GPRXComponent Layout
Note: Not all components, jumpers and connectors are described in this diagram. Refer to your Server SystemService Guide on the Intel® Server Deployment Toolkit CD for additional information.
