8-1 School of Electrical Systems Engineering ABD RAHIM 2008 EET421 Power Electronic Drives - DC to...
-
Upload
sandra-woods -
Category
Documents
-
view
216 -
download
0
Transcript of 8-1 School of Electrical Systems Engineering ABD RAHIM 2008 EET421 Power Electronic Drives - DC to...
8-1
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
EET421Power Electronic Drives
- DC to AC converter / Inverter
Abdul Rahim Abdul Razak
8-2
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-3
Summary
dc-to-ac converters are known as inverters The function of an inverter is to change the dc input voltage to an ac
output voltage of desired magnitude and frequency The output voltage waveforms of ideal inverters should be sinusoidal However, the output of practical inverters contains harmonics For high power applications, low distorted sinusoidal waveforms are
required Harmonic contents could be minimized by the use of high-speed
semiconductor switching techniques
Inverters are widely used in industrial applications- motor drives, UPS, induction heating, standby power
supplies, etc.- input may be a battery, fuel cell, solar cell, or there dc
source
dc-to-ac inverters can make smooth transition into the rectification mode, where the flow of power reverses from the ac side to the dc side
Two types of inverters: single-phase inverters and three-phase inverters
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-4
Switch-Mode DC-AC InvertersApplications: ac motor drives Uninterruptible ac power supplies Where a sinusoidal ac output is required whose
magnitude and frequency both have to be controlled
Terminal voltage is adjustablein its magnitude and frequency
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-5
Switch-Mode DC-AC Inverter: Bi-directional power flow
8-6
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-7
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-8
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-9
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-10
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-11
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-12
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-13
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-14
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-15
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-16
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-17
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-18
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-19
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-20
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
Voltage control of 1-phase inverter
- The needs to have a controllable output voltage :
1) To cope with variations of DC input voltage
2) For inverter voltage regulation
3) For constant volts/frequency control requirement
- Most efficient techniques is by incorporating PWM control within the inverter :
a) Single pulse width modulation - PWM
b) Multiple pulse width modulation - MPWM
c) Sinusoidal pulse width modulation - SPWM
d) Modified sinusiodal pulse width modulation - MSPWM
e) Phase displacement control
8-21
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
a) Single pulse width modulation - PWM
Modulation index:
M=Ar/Ac
Varying Ar from 0 to Ac, will increase the δ thus the output will vary from 0 to Vs
8-22
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
a) Single pulse width modulation - PWM
Modulation index:
M=Ar/Ac
Varying Ar from 0 to Ac, will increase the δ thus the output will vary from 0 to Vs
DF increased badly significantly at low output voltage
3rd harmonic more dominant on single PWM
8-23
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
b) Multiple pulse width modulation - MPWM
fo will set the output frequency while fc will determines the pulses per half cycle,p.
fc / fo = mf, frequency modulation ratio
8-24
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
b) Multiple pulse width modulation - MPWM
fo will set the output frequency while fc will determines the pulses per half cycle,p.
fc / fo = mf, frequency modulation ratio
-By using several pulses, (p=5) The harmonic content are reduced compared to single PWM
- the DF is also reduced significantly.
- but switching loss would increased.
- if p increased, the amplitude of lower order harmonics would be lowered but it will increase the high-orders harmonics
8-25
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
c) Sinusoidal pulse width modulation - SPWM
-Pulse width varied proportional to the amplitude of sinewave ref signal.
- the gating signal generated by comparing the triangular carrier wave and sinusoidal ref signal.
8-26
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
Sinusoidal pulse width modulation - SPWM
Modulation index:
M=Ar/Ac
Varying Ar from 0 to Ac, will increase the δ thus the output will vary from 0 to Vs
-DF is less compared to MPWM
- eliminates the lower order harmonics of 2p-1, for this p=5, lowest order harmonics is 9th.
- the harmonics were pushed to the high frequency range of fc. So it would be much easier for low-pass filtering process.
8-27
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
8-28
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
Overmodulation leads to squarewave operation and add harmonics to the system
8-29
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
d) Modified sinusiodal pulse width modulation - MSPWM
- instead of 100% pulses, carrier wave is applied on 1st and last 60 degree of half cycle.
- advantages :
a) Fundamental component increased
b) Harmonics characteristics are improved.
c) Reduce switching loss.
8-30
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
d) Modified sinusiodal pulse width modulation - MSPWM
advantages :
a) Fundamental component increased
b) Harmonics characteristics are improved.
c) Reduce switching loss.
8-31
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
e) Phase displacement control
- multiple inverter are used, output is taken from summation of output voltage of the individual inverter.
-
2 half bridge inverter output
Output with 180 degree displacement.
Output with β degree displacement
8-32
Three-Phase Inverter
Used to supply three-phase loads Three single-phase inverters could be used with 120 degree displacement
or shifting between phases, however, 12 switches are necessary Consists of three legs, one for each phase One of the two switches in a leg is always ON at any instant Output of each leg depends on Vd and the switching status
8-33
8-34
School of E
lect rical S
ystems E
ngi neer ing
ABD RAHIMABD RAHIM 2008 2008
Current source inverters
- a large inductor component inserted at the input
-input behaves like a current source
-The output current will maintained constant at any loads but output voltage forced to change
-Diodes in series are required to block the reverse voltage on the transistors.