Hole 5 Hole 8 Distance m,ft 14 Hole Out par 30 Hole 10 11 ...
76601IN-0 Kankara Vessel Without THresources.kohler.com/plumbing/kohlerapac/pdf/76601IN...Kankara...
Transcript of 76601IN-0 Kankara Vessel Without THresources.kohler.com/plumbing/kohlerapac/pdf/76601IN...Kankara...
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTION
76601IN-0Kankara Vessel Without TH
· ·
Make a hole of 8.1cm as drain center.Drill faucet hole as per faucet specification.
Ø
Roughing-In NotesFixture dimensions are nominaland conform to tolerances in ASME Standard A112.19.2M.
ROUGH-IN
SERVICE PARTS
Lift rod
Adjust hereCustom linkage
84474
REQUIRED PARTS:Bottle Trap: 75823IN-CP
IMPORTANT:
For pop-up drains, use the custom linkage 84474 instead of thelinkage supplied with the drain.
Item Code:- 84474Item description:- ASSEMBLY ADJUSTABLE LINKAGE
CARE AND CLEANINGTo keep your lavatory looking new, make sure you clean it outthoroughly after each use. DO NOT USE ABRASIVES on thisproduct, as they will scratch and ruin the surface. Stubborn stains, paint, or tar can be removed with turpentine or paint thinner.
NOTE: BEFORE CUTTING COUNTER-TOP, ALLOW FOR FAUCET HANDLE CLEARANCEFINISHED WALL / BACK SPLASH
2”(5
.1)
Installation check List
Leakage between vessel and drain outlet.
Vessel orientation
Visual inspection of applied sealant
COMPATIBLE FAUCETS WITH ABOVE VESSEL (CHECK KOHLER CATALOGUE FOR FAUCET DETAILS)
14404T-4 Purist Single Control Tall Lav Faucet72298IN-4 Aleo Single Control Tall Lav Faucet With Drain
37329T-4-CP Strayt Single Control Tall Lav Faucet With Drain37303IN-4-CP Cuff Sc Tall Lav Faucet With Drain
10217IN-4ND-CP Forte Sc Tall Lav Faucet
10861IN-4-CP Singulier Sc Tall Lav Faucet With Drain8990IN-9-CP Toobi Single Control Tall Lav Faucet
16231IN-4-CP Margaux Single Control Tall Lav With Drain13524IN-4ND-CP Qualis Single Control Tall Lav Faucet Without Drain14761IN-4ND-CP Stance Sc Tall Lavatory Faucet
1288199-IN01-B
BEFORE YOU BEGIN Observe all local plumbing & building codes. Inspect the waste and supply piping for leakages or damage, replace if necessary. Before installation, unpack the new lavatory and carefully inspect it for any transit damage. Return the lavatory to its protective carton until you are ready to install it. Use this template to mark correct cut-out size of lavatory. Assemble the drain to the lavatory before installing it.
· ·
·
·
· ·
TOOLS AND MATERIAL (Not supplied)Safety glassesPencil Scissors Measuring tapePutty knifePlumbers puttyHacksawKeyhole saw or saber sawDrill bit as requiredAdjustable wrenchPipe wrenchTube cutter
· · · · · · · · · · · ·
Unit: Inch (cm)
·
·
·
·
Place this template on the counter top and align with the finish wall markings.Ensure clearance as specified between outer rim of lavatory and finish wall.Trace the template and mark the drain and faucet hole centers.Remove the template.
INSTALLATION
CAUTION: Risk of personal injury orproduct damage.
· Large lavatories are very heavy. Get help lifting the lavatory during installation.Temporarily position the lavatory in thecut-out and adjust to fit.Trace a pencil line around the outside edge of the lavatory.Remove the lavatory.
Make sure drain is installed beforeproceeding further.
NOTE:
·
·
·
· Apply sealant at the joint of lavatoryand counter as shown.
· Carefully position the lavatory inthe cutout, and ensure the bottomface of lavatory is resting properly.
· Verify the orientation of vessel with marking given on template.
·
·
Immediately wipe off any excess sealant, and fill any voids if needed.Allow the sealant to set for at least 30 minutes before any further activities.
Ø3-3/16” (8.1)
C/L (Drain)
Orientation Marking
C/L
Bottom of lavatory(Apply sealant on bottom edge)
Rim of lavatory
10-5/8”(27)
22-3/16”(56.3)
15-7
/8”(
40.3
)
5-1/
8”(1
3)
34”(
86.4
)
1-3/4”(4.5)
Floor
· Align the lavatory drain outlet hole withthe hole on counter top.
Toll Free 1800 103 2244kohler.co.in
© 2016-17 Kohler Co.
2”(5.1)
2”(5.1)
Fini
shed
wal
l
Fini
shed
wal
l
Faucet hole
Drain hole
TEMPLATE / INSTALLATION INSTRUCTIONSEE PCI #IN1601268 20.10.16ARUN BVWA1
SEE PCI #IN1601693 04.01.17ARUN BMWB1
1288199-IN01
ARUN B
04.01.17A.i.
04.01.17 04.01.17
04.01.17JAYESHMW
REFER NOTESREFER NOTES
REFER NOTES
1:1
1 OF 1
NOTES
3) 4) 5)
PRINT AREA = 670x515 mm (26.35”x20.24”)
TITLE BLOCK & NOTES OUTSIDE PRINT AREA(2) SHOULD NOT TO BE PART OF PRINTING.
SHEET SIZE = A1 (ALTERNATE SHEET SIZE 23”x36”)
PAPER MATERIAL : MAPLITHO PAPER , 100 ± 5 GSM
SAMPLE COPY TO BE APPROVED BY KOHLER INDIA ENGINEERING TEAM PRIOR TO PRODUCTION.PRINTING COLOR : BLACK
1) D300_001 : KITCHEN SINK & LAVATORY CUTOUT TEMPLATE DESIGN.
12
6) THE ARTWORK MUST NOT BE SCALED. MUST BE PRINTED ON 100% (1:1) SCALE.6)
2
2
1
515 mm
670 mm
Minimum
Minimum
Min
imum