MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

1 BAHN Left Ignition Cover for Victory — Tuxedo 1 Bracket 1 Hardware Kit containing: 6 M6 X 1.0 X 12 MM Serrated Flange Screws 3 M6 X 1.0 Serrated Flange Nuts 3 External Tooth Lock Washers 1 Installation Instructions

YOU WILL ALSO NEED:

Set of Metric Combination Wrenches

STEP 1 Read and understand all STEPS in the instructions before starting the installation. Park the motorcycle

on a hard, level surface and turn IGN OFF.

This indicat ion a ler ts you to the fact that ignor ing the contents descr ibed here in may negat ive ly a f fect product per formance and funct ional i ty or damage the product i tsel f or the product to which i t is being at tached.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY.

These insta l la t ion instruct ions conta in important informat ion. Ensure that the end user receives th is copy and is aw are of i ts importance for future reference.

Avoid damage to the motorcycle . Protect pa inted surfaces w ith a sof t c loth or b lanket .

-cont.- 7640-12MC-0215

7640 BAHN LEFT IGNITION COVER for VICTORY — TUXEDO

YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.

WORKING AROUND THE SHARP EDGES OF THE CYLINDER-HEAD FINS EXPOSES YOUR HANDS TO INJURY. WEAR PROTECTIVE GLOVES TO PREVENT SERIOUS INJURY.

NOTE: The BAHN Left Hand Ignition Cover for Victory can be

mounted either horizontally or vertically. Decide which way

you want the cover to be mounted before beginning the in-

stallation. PIC 1 and 2

STEP 2 Remove the OEM cover. Gently pull out on the edges of the cover to release

the tabs from the grommets. Set the cover aside, it will not be re-used.

STEP 3 Locate the Bracket in the hardware kit. Refer to PIC 3. Note that the orienta-

tion of the bracket, whether mounted vertically or horizontally, is the same.

PIC 4 and 5

STEP 4 Insert the three included M6 screws through the included External Tooth Lock Washers and into the

threaded holes as shown in PIC 6 and 7. Gently snug the screws. DO NOT OVER TIGHTEN THE

SCREWS!

STEP 5 Refer to PIC 8. Flip the bracket with the screws over and attach the mounting bracket to the cover with

the remaining three M6 screws. The bracket orientation and screw locations will be the same whether

the cover is horizontal or vertical.

2 -cont.-

7640 BAHN LEFT IGNITION COVER for VICTORY — TUXEDO

PIC 8

HORIZONTAL

ATTACH THE BRACKET TO THE COVER WITH THREE SCREWS

PIC 1

VERTICAL FRONT

PIC 2

HORIZONTAL FRONT

TOP

PIC 3

TOP

HORIZONTAL

PIC 4

TOP

VERTICAL

PIC 5

PIC 7

TOP

PIC 6

INSTALL THREE SCREWS WITH LOCK WASHERS IN THREADED HOLES

STEP 6 Refer to PIC 9 and 10. Position the cover assembly on the igni-

tion bracket . The three studs will fit in the three slots in the

ignition bracket. Attach it to the ignition bracket from the back-

side with the three included M6 nuts. Leave the nuts loose until

all three have been started and the cover is aligned with the

ignition switch face, then tighten the nuts.

I t is the end user ’s responsibi l i ty to ensure that a l l o f the fasteners ( inc luding pre-assembled) are t ightened before operat ion of the motorcycle . Küryakyn w i l l not provide w arranty coverage on products or components lost due to improper insta l la t ion or lack of maintenance. Per iodic inspect ion and maintenance are required on a l l fasteners .

TIPS FOR PROPER CARE:

Your new BAHN product is made out of anodized aluminum. Anodized aluminum requires special attention when cleaning. Some cleaning products or procedures can actually remove the anodized treatment which will lead to pitting in the aluminum.

Thoroughly clean the BAHN product often with a soft cloth, mild soap and water. Regular cleaning keeps contaminates from building up.

Rinse thoroughly with FRESH water.

Use only metal protection products that are formulated for anodized aluminum.

DO NOT USE bleach or chlorides to clean the BAHN product.

DO NOT USE products containing abrasives to clean the BAHN product. Never use steel or brass wool, wire brushes, polishing wheels, rubbing or polishing compounds on the BAHN product.

DO NOT USE concentrated alkaline based solutions to clean the BAHN product. Many detergents are alkaline based.

7640 BAHN LEFT IGNITION COVER for VICTORY — TUXEDO

3

PIC 9

IGNITION SWITCH FACE

PIC 10

IGNITION SWITCH FACE