76 Exterior and Interior Trim

760C9–02

B57670

Front Fender Liner RH

Front Bumper ReinforcementSub–assy

Front Bumper EnergyAbsorber

Front Fender Liner LH

Cooler Thermistor

Front Bumper Cover

Front Bumper Hole Cover LH

Front Bumper Hole Cover RH

Fog Lamp Assy LH

Fog Lamp Assy RH

Engine Under Cover LH

Engine Under Cover RH

Front BumperReinforcementSub–assy Upper

Front Bumper Cover Lower

Front Bumper Extention MountingBracket

TMC Made:

TMC Made:

N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque

34 (350, 25)

34 (350, 25)

–EXTERIOR/INTERIOR TRIM FRONT BUMPER76–1

2704Author�: Date�:

2002 CAMRY REPAIR MANUAL (RM881U)

FRONT BUMPERCOMPONENTS

760BN–03

B55729

B55730

76–2–EXTERIOR/INTERIOR TRIM FRONT BUMPER



REPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.1. REMOVE ENGINE UNDER COVER LH(a) Remove the 4 screws.(b) Using a screwdriver, remove the 4 clips and engine under cover.2. REMOVE ENGINE UNDER COVER RH(a) Remove the 3 screws.(b) Using a screwdriver, remove the 3 clips and engine under cover.

3. REMOVE FRONT FENDER LINER LH(a) Remove the screw and a part of the front fender liner LH.HINT:Remove the screw and the front fender liner LH within the rangethat the front bumper cover can be removed.4. REMOVE FRONT FENDER LINER RH

5. REMOVE FRONT BUMPER COVER(a) Remove the 2 screws and 2 bolts.(b) Using a clip remover, remove the clip.(c) Disengage the hooks and remove the front bumper cover.(d) Disconnect the fog lamp connectors (on the fog lamp op-

tion only).

6. REMOVE FRONT BUMPER ENERGY ABSORBER7. REMOVE FRONT BUMPER REINFORCEMENT SUB–ASSY(a) Disconnect the cooler thermistor connector and wire harness clips.(b) Remove the 6 bolts and reinforcement.8. REMOVE FRONT BUMPER REINFORCEMENT SUB–ASSY UPPER(a) Remove the 8 bolts, 4 nuts and frontbumper reinforcement sub–assy upper.9. REMOVE FOG LAMP ASSY LH (See page 65–12)10. REMOVE FOG LAMP ASSY (See page 65–12)11. REMOVE COOLER (AMBIENT TEMP. SENSOR) THERMISTOR12. REMOVE FRONT BUMPER EXTENTION MOUNTING BRACKET (Only TMC made)13. REMOVE FRONT BUMPER COVER LOWER (Only TMC made)

–EXTERIOR/INTERIOR TRIM FRONT BUMPER76–3



14. REMOVE FRONT BUMPER HOLE COVER RH(a) Disengage the hooks and remove the front bumper hole cover.15. REMOVE FRONT BUMPER HOLE COVER LH16. INSTALL FRONT BUMPER REINFORCEMENT SUB–ASSY(a) Install the front bumper reinforcement with 6 bolts.

Torque: 34 N ⋅m (350 kgf ⋅cm, 25 ft ⋅lbf)

760BL–03

B56513

Luggage Compartment Trim CoverInner LH

Luggage Compartment TrimCover Inner RH

Luggage CompartmentFloor Mat

Luggage Compartment TrimHook No.1

Spare Wheel Cover Assy

Luggage Compartment Trim Hook No.1

Rear Floor Finish Plate

Rear Bumper EnergyAbsorber

Rear Bumper Reinforcement Sub–assy

Rear Bumper Cover

Luggage Compartment Side CoverSub–assy RH

Rear Bumper SideRetainer LH

Rear Bumper RetainerUpper RH

Rear Bumper RetainerUpper LH

Rear Bumper Side Retainer RH

34 (350, 25)

34 (350, 25)

N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque

76–4–EXTERIOR/INTERIOR TRIM REAR BUMPER



REAR BUMPERCOMPONENTS

760BM–02

B56105Clips

B60006

–EXTERIOR/INTERIOR TRIM REAR BUMPER76–5



REPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT2. REMOVE SPARE WHEEL COVER ASSY3. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB–ASSY RH4. REMOVE LUGGAGE COMPARTMENT TRIM HOOK NO.1(a) Remove the 2 bolts and luggage compartment trim hooks.

5. REMOVE REAR FLOOR FINISH PLATE(a) Disengage the clips and remove the rear floor finish plate.6. REMOVE LUGGAGE COMPARTMENT TRIM COVER

INNER RH(a) Using a clip remover, remove the 2 clips and luggage

compartment trim cover inner.7. REMOVE LUGGAGE COMPARTMENT TRIM COVER

INNER LH

8. REMOVE REAR BUMPER COVER(a) Remove the 8 nuts, 4 bolts and 4 clips.(b) Remove the 2 screws and rear bumper cover.(c) Disengage the rear bumper seal bracket and remove the

rear bumper cover.

9. REMOVE REAR BUMPER SIDE RETAINER RH(a) Remove the clip and rear bumper side retainer. (Only TMC made)(b) Remove the rivet and rear bumper side retainer. (Only TMMK made)10. REMOVE REAR BUMPER SIDE RETAINER LH11. REMOVE REAR BUMPER RETAINER UPPER RH(a) Remove the 3 clips and rear bumper retainer upper. (Only TMC made)(b) Remove the 4 rivets and rear bumper retainer upper. (Only TMMK made)12. REMOVE REAR BUMPER RETAINER UPPER LH13. REMOVE REAR BUMPER ENERGY ABSORBER14. REMOVE REAR BUMPER REINFORCEMENT SUB–ASSY(a) Remove the 6 nuts and rear bumper reinforcement.15. INSTALL REAR BUMPER REINFORCEMENT SUB–ASSY(a) Install the front bumper reinforcement with 6 nuts.

Torque: 34 N ⋅m (350 kgf ⋅cm, 25 ft ⋅lbf)

760BK–02

B56106

Clip

B56107

Clip

76–6–EXTERIOR/INTERIOR TRIM REAR SPOILER SUB–ASSY



REAR SPOILER SUB–ASSYREPLACEMENTHINT:Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.1. REMOVE LUGGAGE COMPARTMENT DOOR COVER(a) Remove the 15 clips and luggage compartment door cover.2. REMOVE REAR SPOILER SUB–ASSY(a) Remove the 2 nuts.(b) Put protective tape onto the body.(c) Using a heat light, heat the spoiler 40 – 60�C (104 – 140�F).NOTICE:Do not heat the spoiler excessively.

(d) Tie both piano wire ends to wooden blocks or similar ob-jects.(1) Scrape the adhesive tape off by pulling the piano

wire as shown in the illustration.(2) If reusing the rear spoiler, take care not to damage

the rear spoiler.NOTICE:Do not damage the body.(e) Disconnect the connector.

(f) Remove the 2 clips and rear spoiler.

3. REMOVE CENTER STOP LAMP ASSY (See page 65–16)4. INSTALL REAR SPOILER SUB–ASSY(a) Using a heat light, heat the body mounting surface to 40 – 60�C (104 – 140�F).NOTICE:Do not heat the body excessively.(b) Remove the protective tape from the body.(c) Wipe off the stains with cleaner.

B55741

–EXTERIOR/INTERIOR TRIM REAR SPOILER SUB–ASSY76–7



(d) Clean the rear spoiler (if reusing the spoiler).(1) Using a heat light, heat the rear spoiler to 40 – 60�C (104 – 140�F).

NOTICE:Do not heat the spoiler excessively.

(2) Remove the adhesive tape from the rear spoiler.(3) Wipe off the stains with cleaner.

(4) Install new adhesive tape to the rear spoiler asshown in the illustration.

(e) Using a heat light, heat the body and moulding.HINT:� Body: 40 – 60�C (104 – 140�F)� Moulding: 20 – 30�C (68 – 86�F)

(f) Install the rear spoiler with 2 nuts.

760BZ–01

B55976

PLATE, LUGGAGE COMPARTMENT DOOR NAME, NO.7

PLATE, LUGGAGE COMPARTMENT DOOR, NO.489

(3.63)

233.8(9.543)

59 (2.32)

82.2 (3.355)

22 (0.90) (0.539)13.2

236 (9.63)

Luggage Door Line Garnish Luggage Compart-ment Door Outs End

Luggage Door Line End

Garnish Luggage CompartmentDoor Outs End

Garnish Luggage CompartmentDoor Outs End

Luggage Door Line


Luggage Door Line


PLATE, LUGGAGE COMPARTMENT DOOR NAME, NO.2 PLATE, LUGGAGE COMPARTMENT DOOR, NO.3

mm(in.)

76–8–EXTERIOR/INTERIOR TRIM NAME PLATE



NAME PLATEREPLACEMENT

760CA–01

B56420

Protective Tape

–EXTERIOR/INTERIOR TRIM FRONT DOOR BELT MOULDING ASSY LH76–9



FRONT DOOR BELT MOULDING ASSY LHREPLACEMENTHINT:� Installation is in the reverse order of the removal. But the installation is indicated only when it has a

point.� In the RH side, work in the same procedure as in the LH side.

1. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY(See page 75–8)

2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH(See page 75–8)

3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH(See page 75–8)

4. REMOVE FRONT DOOR TRIM BOARD SUB–ASSY LH(See page 75–8)

5. REMOVE OUTER REAR VIEW MIRROR ASSY LH(See page 75–8)

6. REMOVE FRONT DOOR BELT MOULDING ASSY LH

(a) Put protective tape under the front door belt moulding.(b) Using a moulding remover or scraper, remove the front

door belt moulding.HINT:Tape the scraper tip before use.

760CB–01

B56421

Protective Tape

76–10–EXTERIOR/INTERIOR TRIM REAR DOOR BELT MOULDING ASSY LH



REAR DOOR BELT MOULDING ASSY LHREPLACEMENTHINT:� Installation is in the reverse order of the removal. But the installation is indicated only when it has a


1. REMOVE REAR DOOR BELT MOULDING ASSY LH

(a) Put protective tape under the rear door belt moulding.(b) Using a moulding remover or scraper, remove the rear

door belt moulding.HINT:Tape the scraper tip before use.

760BP–03

B56185

ProtectiveTape

Clip

–EXTERIOR/INTERIOR TRIM ROOF DRIP SIDE FINISH MOULDING CENTER LH76–11



ROOF DRIP SIDE FINISH MOULDING CENTER LHREPLACEMENTHINT:� Installation is in the reverse order of the removal. But the installation is indicated only when it has a


1. REMOVE ROOF DRIP SIDE FINISH MOULDINGCENTER LH

(a) Tape the circumference of the moulding for protection.(b) Using a remover for the roof moulding, release the en-

gagements of the clips both in the front and rear ends ofthe moulding, and then remove the roof drip side finishmoulding.

NOTICE:� Do not remove the clips.� If the clips are damaged or removed accidentally, ex-

change them for supplied ones.2. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP NO.1NOTICE:Only when exchanging the clips.(a) Remove the adhesive tape that remains on the mounting surface of the body, and then clean the sur-

face with white gasoline.(b) Heat up the clip installation surfaces of the body with a heat light.

Body: 40 – 60 �C (104 – 140�F)Moulding: 20 – 30 �C (68 – 86�F)

NOTICE:Do not heat the moulding excessively.(c) Set the supplied clips into the positions as shown in the illustration, and press–fit those clips by hand

to install them.(d) Install the moulding when 30 minutes or more have passed after press–fitting the clips.HINT:� Initial hardening time: 30 minutes� Perfect hardening time: 24 hours

B56186

2.5 mm (0.098 in. ) 1.7 mm (0.067 in. )

Front Side Rear Side

76–12–EXTERIOR/INTERIOR TRIM ROOF DRIP SIDE FINISH MOULDING CENTER LH



760BQ–03

B56187

Protective Tape

B56188

Front Door Outside Moulding Rear Door Outside Moulding

Adhesive Tape

–EXTERIOR/INTERIOR TRIM OUT SIDE MOULDING76–13



OUT SIDE MOULDINGREPLACEMENTHINT:� Installation is in the reverse order of the removal. But, the installation is indicated only when it has a


1. REMOVE OUT SIDE MOULDING(a) Using a heat light, heat the body moulding to 40 – 60�C

(104 – 140�F).NOTICE:Do not heat the moulding excessively.(b) Tie both piano wire ends to wooden block or similar ob-

ject.(c) Scrape the adhesive tape off by pulling the piano wire as

shown in the illustration.NOTICE:� If reusing the moulding, take care not to damage the

moulding.� Do not damage the body.

2. INSTALL OUT SIDE MOULDING(a) Using a heat light, heat the body mounting surface to 40 – 60�C (104 – 140�F).NOTICE:Do not heat the body excessively.(b) Remove the protective tape from the body.(c) Wipe off the stains with cleaner.(d) Clean the moulding (if reusing the moulding).

(1) Using a heat light, heat the body moulding to 20 – 30�C (68 – 86�F).NOTICE:Do not heat the body excessively.

(2) Remove the adhesive tape from the moulding.(3) Wipe off the stains with cleaner.(4) Apply new adhesive tape to the moulding as shown in the illustration.

BO5229

76–14–EXTERIOR/INTERIOR TRIM OUT SIDE MOULDING



(e) Using a heat light, heat the body and moulding.HINT:� Body: 40 – 60�C (104 – 140�F)� Moulding: 20 – 30�C (68 – 86�F)

NOTICE:Do not heat the body excessively.

(f) Lift the moulding release sheet from the face moulding.NOTICE:� When the moulding release sheet is removed, take

care that no d irt or no dust can get onto the uncoatedarea.

� Do not apply excessive force onto the moulding, butsteady pressure with your thumbs.

760BR–03

B56189

Clip

–EXTERIOR/INTERIOR TRIM ROCKER PANEL MOULDING LH76–15



ROCKER PANEL MOULDING LHREPLACEMENT

1. REMOVE ROCKER PANEL MOULDING LH(a) Remove the 6 screws.(b) Using a screwdriver, remove the rocker panel moulding.HINT:Tape the screwdriver tip before use.

760BS–03

B56190

Clip

76–16 –EXTERIOR/INTERIOR TRIM LUGGAGE COMPARTMENT DOOR GARNISHSUB–ASSY OUTSIDE



LUGGAGE COMPARTMENT DOOR GARNISH SUB–ASSYOUTSIDEREPLACEMENT1. REMOVE LUGGAGE COMPARTMENT DOOR COVER(a) Remove the 15 screws and luggage compartment door cover.

2. REMOVE LUGGAGE COMPARTMENT DOORGARNISH SUB–ASSY OUTSIDE

(a) Remove the 4 screws.(b) Using a screwdriver, remove the luggage compartment

door garnish outside.HINT:Tape the screwdriver tip before use.

760BT–03

B56191

Clip

–EXTERIOR/INTERIOR TRIM FRONT FLOOR FOOTREST76–17



FRONT FLOOR FOOTRESTREPLACEMENT

1. REMOVE FRONT FLOOR FOOTREST(a) Holding the floor mat, disengage the clips from the upper

with a screwdriver to remove the front floor footrest.HINT:Tape the screwdriver tip before use.NOTICE:Warm the inside of the vehicle well before removal.(b) Disengage the foot rest clips, and then remove the 2 clips

from the front floor footrest.

2. INSTALL FRONT FLOOR FOOTREST(a) Install the footrest clips by engaging the claws with the front floor footrest.(b) Before installation, check that the part to be engaged with the clips of front floor footrest is not dam-

aged.NOTICE:If it is damaged, replace it with a new one.

760C7–01

B57089

Front PillarGarnish RH

Front Door OpeningTrim Weatherstrip RH

Center Pillar Garnish RH

Rear Door OpeningTrim Weatherstrip RH

Front Door Scuff Plate RHCenter Pillar Garnish Lower RH

Roof Side Garnish Inner RH

Roof Side Garnish Inner LH

w/ Curtain Shield Airbag

Rear Door Scuff Plate RH



42 (420, 31)

w/ Curtain Shield AirbagFront PillarGarnish LH

Front Door OpeningTrim Weatherstrip LH

Front Door Scuff Plate LH Rear Door Scuff Plate LH

Lap Belt Outer Anchor Cover

Center Pillar Garnish LH

Rear Door OpeningTrim Weatherstrip LH

Center Pillar Garnish Lower LH

42 (420, 31)

N⋅m (kgf⋅cm ft⋅lbf) : Specified torque

76–18–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY



ROOF HEADLINING ASSYCOMPONENTS

B57088

w/ Moon Roof

Visor Assy RH

Visor Holder

Roof Headlining Assy

Visor Bracket Cover

Roof Console Box Assy

Room Lamp Assy No.1

w/ Erectro Chromic Inner Mirror:Inner Rear View Mirror Cover

Visor Assy LHVisor Holder

Visor Bracket Cover

Assist Grip Sub–assy

Assist Grip Sub–assyAssist Grip

Sub–assyAssist Grip Cover

Assist Grip Cover

w/ Sunshade:Sunshade Trim Holder

Roof Headlining Assy

w/ Sunshade:Sunshade Trim Holder

Lens

Sun Roof Opening Trim Moulding

Assist Grip Sub–assy

Assist Grip Cover

–EXTERIOR/INTERIOR TRIM ROOF HEADLINING ASSY76–19



760C8–01

B57751




REPLACEMENTHINT:Installation is according to the reverse order of the removal.1. REMOVE FRONT SEAT ASSEMBLY RH

(Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27)2. REMOVE FRONT SEAT ASSEMBLY LH

(Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27)3. REMOVE REAR SEAT CUSHION ASSY (See page 72–34, 72–38)4. REMOVE REAR SIDE SEAT BACK ASSY RH

(See page 72–34, 72–38)5. REMOVE REAR SIDE SEAT BACK ASSY LH

(See page 72–34, 72–38)6. REMOVE REAR SEAT BACK ASSY (See page 72–34, 72–38)7. REMOVE CONSOLE PANEL UPPER REAR

(See page 71–12)8. REMOVE RR CONSOLE BOX (See page 71–12)9. REMOVE CONSOLE PANEL UPPER

(See page 71–12)10. REMOVE CONSOLE BOX ASSY REAR

(See page 71–12)11. REMOVE CONSOLE BOX DUCT NO.1

(See page 55–29)12. REMOVE AIR DUCT REAR NO.1

(See page 55–29)13. REMOVE AIR DUCT REAR NO.2

(See page 55–29)14. REMOVE FLOOR SHIFT ASSY(See page 40–39)

15. REMOVE FRONT DOOR SCUFF PLATE RH

(a) Using a screwdriver, remove the front door scuff plate.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other

side.16. REMOVE FRONT DOOR SCUFF PLATE LH

B57752

B56896

B57064




17. REMOVE REAR DOOR SCUFF PLATE RH

(a) Using a screwdriver, remove the rear door scuff plate.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other

side.18. REMOVE REAR DOOR SCUFF PLATE LH

19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

20. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

23. REMOVE CENTER PILLAR GARNISH LOWER RH

(a) Pull the center pillar lower garnish upward to remove it.(b) Employ the same manner described above to the other

side.24. REMOVE CENTER PILLAR GARNISH LOWER LH

25. REMOVE CENTER PILLAR GARNISH UPPER RH

(a) Using a screwdriver, remove the lap belt outer anchorcover.

HINT:Tape the screwdriver tip before use.(b) Remove the bolt and front seat outer belt floor anchor.

B56900

B56897

B56901

B56910




(c) Remove the 2 clips(d) Using a screwdriver, remove the center pillar upper gar-

nish.HINT:Tape the screwdriver tip before use.(e) Employ the same manner described above to the other

side.26. REMOVE CENTER PILLAR GARNISH UPPER LH

27. REMOVE ROOF SIDE GARNISH INNER RH(W/OCURTAIN SHIELD AIR BAG)

(a) Using a screwdriver, remove the roof side garnish inner.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other

side.28. REMOVE ROOF SIDE GARNISH INNER LH(W/O

CURTAIN SHIELD AIR BAG)

29. REMOVE ROOF SIDE GARNISH INNER RH(W/CURTAIN SHIELD AIR BAG)

(a) Using a screwdriver, remove the roof side garnish innercover.

HINT:Tape the screwdriver tip before use.(b) Remove the bolt.(c) Using a screwdriver, remove the roof side garnish inner.HINT:Tape the screwdriver tip before use.30. REMOVE ROOF SIDE GARNISH INNER LH(W/

CURTAIN SHIELD AIR BAG)

31. REMOVE FRONT PILLAR GARNISH RH(W/OCURTAIN SHIELD AIR BAG)

(a) Using a screwdriver, remove the front pillar garnish.HINT:Tape the screwdriver tip before use.(b) Employ the same manner described above to the other

side.

B56914

B55645

Tape

Tape

Tape

Protective Cover

120 mm

700 mm

B53950

Protection Tape




32. REMOVE FRONT PILLAR GARNISH LH(W/O CURTAINSHIELD AIR BAG)

33. REMOVE FRONT PILLAR GARNISH RH(W/ CURTAINSHIELD AIR BAG)

(a) Using a screwdriver, remove the front pillar garnish cover.HINT:Tape the screwdriver tip before use.(b) Remove the bolt.(c) Using a screwdriver, remove the front pillar garnish.HINT:Tape the screwdriver tip before use.

(d) Protect the curtain shield airbag.NOTICE:Cover the curtain shield airbag with the protection cover assoon as the front pillar garnish is removed.

(1) Cover the airbag with cloth or nylon of 700 mm(27.56 in.) × 120 mm (4.72 in.) and fix the ends ofthe cover with tape, as shown in the illustration.

(e) Employ the same manner described above to the otherside.

34. REMOVE FRONT PILLAR GARNISH LH(W/ CURTAINSHIELD AIR BAG)

35. REMOVE ASSIST GRIP SUB–ASSY

(a) Using a screwdriver, remove the assist grip cover.HINT:Tape the screwdriver tip before use.(b) Remove the 2 screws and assist grip.

B57173

B56911

B57174

Cutout Part

B57175




36. REMOVE RH VISOR ASSY

(a) Using a moulding remover, remove the visor bracket cov-er.

HINT:Tape the screwdriver tip before use.(b) Remove the 2 screws and assist grip.37. REMOVE LH VISOR ASSY

38. REMOVE ROOF CONSOLE BOX ASSY

(a) Using a screwdriver, remove the roof console box thendisconnect the connector.

HINT:Tape the screwdriver tip before use.

39. REMOVE ROOM LAMP ASSY NO.1

(a) Using a screwdriver, remove the lens.

(b) Using a screwdriver, remove the room lamp assemblyNo.1 then disconnect the connector.

HINT:Tape the screwdriver tip before use.

B50596

90�

B56912

B56438




40. REMOVE VISOR HOLDER

(a) Remove the holder of the sun visor by turning it to the left.

41. REMOVE SUN ROOF OPENING TRIM MOULDING(W/ SLIDING ROOF)

42. REMOVE ROOF HEADLINING ASSY

(a) Remove the 2 sunshade trim holders.(b) w/ Erectro chromic inner mirror:

Remove the inner rear view mirror cover.(c) Tear off the tape on the adhered part of the wire harness.

(d) Remove the headlining assembly from the passenger’sdoor.

B56917

w/ Sliding roof

w/o Sliding roof

Tape

Tape




43. INSTALL ROOF HEADLINING ASSY

(a) Align the markings, then install the wire harness with tape.HINT:Be careful for dirt or foreign objects not to stick to the adheredpart when peeling the double–stick tape.(b) Attach the roof wire harness across the adhered partNOTICE:Roof wire harness should be attached securely.

44. INSTALL FRONT SEAT ASSEMBLY LH(Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27)

45. INSTALL FRONT SEAT ASSEMBLY RH(Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27)

76 Exterior and Interior Trim

Documents

Transcript of 76 Exterior and Interior Trim