7400 Series Logic ICs
-
Upload
jeffry-bahari -
Category
Documents
-
view
220 -
download
0
Transcript of 7400 Series Logic ICs
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 1/10
Application Note 11 Micrel
2-70 1997
General DescriptionThis application note describes the interface connectionsbetween Micrel PCMCIA Power Controllers and industrystandard logic controllers from Cirrus Logic, Data Book, Intel,and Vadem. Combining one or two Micrel PC Card PowerController s and one of these controllers produces a completePCMCIA-compatible PC Card slot. In most cases, no othercomponents are necessary.This note concentrates on the power control subsystem only.For full details on designing-with and operating the PC Cardlogic controllers, please refer to the respective manufacturer’sliterature. For detailed specifications and additional informa-tion on the MIC2560, MIC2561, MIC2562, and MIC2563please see their datasheets earlier in this section.
OverviewThe MIC2560 is a fully-protected PC Card Power Controllerthat meets all PCMCIA specifications. It provides full controlof both V CC and V PP for one PC Card slot. It features industry-leading ON resistances and is available in different controllogic configurations for “glueless” compatibility with the majorindustry-standard PC Card logic controllers.The MIC2561 is also a fully protected card slot controller,similar to the MIC2560, but has higher ON resistances,enabling its use in price-sensitive applications. It is availablein the same MIC2560 pinout as well as in a smaller packagethat is less than half the size of the MIC2560.The MIC2562 is a new design, providing full functionality froma 3.3V supply. The new MIC2563 is a dual version of the
MIC2562 in a SSOP package.
Application Note 11Interfacing PC Card Power Controllers to Logic
Controllers
This note details the connections between the PCMCIA slot logic controller and Micrel PC Card Power Controllers.
SystemPowerSupply
PCMCIACard SlotController MIC2563
PCMCIACard Slot
A
5V(opt)
12V(opt)
A EN0
A EN1
VPP1
VCC
VPP IN(opt)
VCC5 IN(opt)
VCC3 IN
A VCC5_EN
A VCC3_EN
VPP2
PCMCIACard Slot
VPP1
VCC
VPP2B EN0
B EN1
B VCC5_EN
B VCC3_EN
PCMCIACard Slot
B
3.3V
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 2/10
Application Note 11 Micre
1997 2-71
Cirrus Logic Controllers
Table 1. CL-PD6710 single slot controller and MIC2560-1/MIC2561-1 pin equivalencies.
Table 2. CL-PD6720 dual slot controller and MIC2560-1/MIC2561-1 pin equivalencies.
Table 3. CL-PD6729 dual slot controller and MIC2560-1/MIC2561-1 pin equivalencies.
PC Card logic controllers from Cirrus Logic are compatiblewith Micrel’s “–1” option of PC Card power controllers. Tables1, 2, and 3 show pin connections between three popularCirrus Logic controllers and the MIC2560-1 and MIC2561-1.Figure 1 is a schematic of a typical two slot PC Cardimplementation using the CL-PD6720 and the MIC2560-1.
CL-PD6710 MIC2560-1BWM MIC2561-1BMMIC2561-1BWM MIC2562-1BM
Pin Name Pin # Pin Name Pin # Pin #
VCC_5 6 V CC5_EN 5 1
VCC_3 5 V CC3_EN 6 2
VPP_VCC 3 V PP_VCC 7 3
VPP_PGM 2 V PP_PGM 8 4
CL-PD6720 MIC2560-1BWM MIC2561-1BM MIC2563-1BSM
MIC2561-1BWM MIC2562-1BM
Pin Name Pin # Pin Name Pin # Pin # Pin #
Slot A Slot B Slot A Slot B
VCC_5 5 207 V CC5_EN 5 1 5 19
VCC_3 4 206 V CC3_EN 6 2 6 20
VPP_VCC 2 205 V PP_VCC 7 3 7 21
VPP_PGM 1 204 V PP_PGM 8 4 8 22
CL-PD6729 MIC2560-1BWM MIC2561-1BM MIC2563-1BSM
MIC2561-1BWM MIC2562-1BM
Pin Name Pin # Pin Name Pin # Pin # Pin #Slot A Slot B Slot A Slot B
VCC_5 130 138 V CC5_EN 5 1 5 19
VCC_3 129 136 V CC3_EN 6 2 6 20
VPP_VCC 128 135 V PP_VCC 7 3 7 21
VPP_PGM 127 134 V PP_PGM 8 4 8 22
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 3/10
Application Note 11 Micrel
2-72 1997
Cirrus Logic CL-PD6720 Application Circuit
12
12
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-1BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-1BWM
VCC
VPP
VCC
VPP
Slot B
Slot A
3.3V 5V 12V
A_VCC_5A_VCC_3
A_VPP_VCCA_VPP_PGM
B_VCC_5B_VCC_3
B_VPP_VCC
B_VPP_PGM
A_SLOT_VCC
B_SLOT_VCC
C i r r u s
L o g
i c C L - P
D 6 7 2 0
Figure 1. A typical two slot PC Card (PCMCIA) implementation using the Cirrus Logic CL-PD6720 and twoMIC2560-1. The lower cost MIC2561-1BWM may be directly substituted for the MIC2560-1 in this circuit. The
MIC2561-1BM will also work: refer to Table 2 for pin connection changes.
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 4/10
Application Note 11 Micre
1997 2-73
Data Book ControllersMicrel’s option “–2” PC Card power controllers are designedto interface with Data Book logic controllers. The Data Bookdevices have individually programmable power supply con-trol pin polarity, which is determined at power-up. Resistorsare used to force positive polarity for proper interfacing withthe MIC2560-2. Refer to the control logic shown in Table 4 fordetails. When V CC is deselected (OFF), a MIC2560-2 internalclamp actively pulls-down the output, insuring zero volts on
the socket. This clamp has an ON resistance of approxi-mately 1.2k Ω. The Databook DB86184 PCMCIA controllerrequires 100k Ω pull-down resistors from VCCSEL0,VCCSEL1, VPPSEL0, and VPPSEL1 to ground and 100kpull-up resistors from VCCSEL2 and VCCSEL3 to +3.3V (or+5V). MIC2560-2 pin 8 should be connected to ground.While not required, a 0.1 µF capacitor from V CC3 IN to grounprovides decoupling for the current sense amplifier.
12
12
EN1 1
EN0 1
VDD
VCC 3/5VCC EN
GND
76
5
4
3
2
1110
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCCSEL1
VCCSEL2
VPPSEL
FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-2BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCCSEL1
VCCSEL2
VPPSELFLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-2BWM
VCC
VPP
VCC
VPP
Slot B
Slot A
3.3V 5V 12V
VCCSEL0
VCCSEL2VPPSEL0
VCCSEL1VCCSEL3VPPSEL1
VDD S0 1, VDD S1 1
VDD S0 2, VDDS1 2
D a
t a B o o
k D B 8 6 1 8 4
OVERCUR# (opt)100k Ω(x 3)
100k Ω(x 3)
Pin 5 Pin 6 Pin 7 Pins 2 & 14 Pin 13VCCSEL1 VCCSEL2 VPPSEL VCC OUT VPP OUT
0 1 0 Clamped to Ground Clamped to Ground1 1 0 3.3V 3.3V0 0 0 3.3V 12V1 0 0 3.3V Clamped to Ground0 1 1 Clamped to Ground Clamped to Ground1 1 1 5V 5V
0 0 1 5V 12V1 0 1 5V Clamped to Ground
Table 4. MIC2560-2 Logic
Figure 2. The Data Book DB86184 and two MIC2560-2BWM in a typical two slot application.
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 5/10
Application Note 11 Micrel
2-74 1997
Intel ControllersIntel PC Card logic controllers generally interface with theoption “–0”, MIC2560-0 and MIC2561-0. The older Intel82365 supports two V PP pins per slot, but only one V CC level(5V). Use the MIC2558 PCMCIA Dual Card Slot V PP Switch-ing Matrix to control the additional V PP for each socket. Sincethe MIC2558 has separate V CC inputs, full independencebetween V PP2 of slot A and V PP2 of slot B is maintained. Since
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
12
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
I n t e l 8 2 3 6 5 S L
VPP 1_EN0 (pin 75)VPP 1_EN1 (pin 76)
VPP 2_EN0 (pin 77)VPP 2_EN1 (pin 78)
VPP 1_EN0 (pin 158)
VPP 1_EN1 (pin 159)
VPP 2_EN0 (pin 160)VPP 2_EN1 (pin 1)
VCC _EN
VCC _EN
12
MIC2558
7
6
5
4
3
2
8
9
10
11
12
13
14
+5V +12V
VCC
VPP1
VPP2
VCC
VPP1
VPP2
Slot A
Slot B
only 5V is available for V CC OUT, connect all MIC2560/ MIC2561 V CC inputs together. These inputs, including bothVCC3 IN pins, are rated to 6V, so no damage will occur. Takeadvantage of the lower ON resistance of the 3.3V V CC switchby using the V CC3_EN control as the V CC enable. Figure 3shows this configuration.
Figure 3. A two slot configuration using the Intel 82365 controller and the MIC2560-0. Note that this Intelcontroller does not support 3.3V supplies: for best results, connect the +5V supply to all V CC pins (both V CC3 IN
pins and the V CC5 IN pin.
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 6/10
Application Note 11 Micre
1997 2-75
Interfacing with the Intel PPEC PCI to PCMCIA logic controllerThe Intel PPEC (PCI to PCMCIA Enhanced IDE Controller)is a dual slot, dual V CC controller that does not provide latcheddata outputs for power control. Thus, an external latch isrequired. This latch is easily implemented using a 74273 or
equivalent Octal D Flip-Flop. One octal latch supplies twoslots (two MIC2560-0 or MIC2561-0). Figure 4 and Table 5illustrate this system.
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
D
CLOCKCLEAR
Q
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
12
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
GND
7
6
5
4
3
2
11
10
12
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
+5V
19
16
15
12
9
6
5
2
1
11
17
14
13
8
7
4
3
18
74273Octal D Flip-flop with clear
109
113
115
117
120
122
170172174
A C D A T A 0
PWRWR#
A C D A T A 2
A C D A T A 1
ACDATA7
ACDATA6
ACDATA3
ACDATA4
ACDATA5
IntelPPEC
MicrelMIC2560-0BWM
MicrelMIC2560-0BWM
Table 5. Power controlsignals for Figure 4.
Figure 4. A dual slot system using the Intel PPEC controller and the MIC2560-0/MIC2561-0.
Intel PPEC 74273 MIC2560-0Power Signal Pin Name Pin # Pin # In Pin # Out Pin Name Pin #A-EN0 ACDATA0 170 3 2 EN0 7
A-EN1 ACDATA1 172 4 5 EN1 8
A-VCC3V ACDATA4 115 7 6 V CC3_EN 6
A-VCC5V ACDATA5 117 8 9 V CC5_EN 5
B-EN0 ACDATA2 174 13 12 EN0 7
B-EN1 ACDATA3 113 14 15 EN1 8
B-VCC3V ACDATA6 120 17 16 V CC3_EN 6
B-VCC5V ACDATA7 122 18 19 V CC5_EN 5
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 7/10
Application Note 11 Micrel
2-76 1997
Omega Micro ControllersThe MIC2560, MIC2561, MIC2562, and MIC2563 are com-patible with Omega Micro logic controllers, including the82C722GX ISA to PCMCIA (use the “–1” option, shown inFigure 5) and the 82C094 PCI to PCMCIA (use the “–0”option, shown in Figure 6) controllers. Both controllers sup-
port dual V CC voltages to dual slots. The 82C094 offers aserial control output: the Omega Micro 82C28 converts thisserial output into the latched parallel control required byMicrel MIC256x-0 Power Controllers.
Figure 6. The Omega Micro 82C094 and two MIC256x-0 (or one MIC2563-0) adapt the PCI bus to PCMCIA. AnOmega Micro 82C28 converts serial output from the 82C094 to the parallel control needed by the MIC256x-0.
12
12
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-1BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-1BWM
VCC
VPP
VCC
VPP
Slot B
Slot A
3.3V 5V 12V
A_VCC_5A_VCC_3
A_VPP_VCCA_VPP_PGM
B_VCC_5B_VCC_3
B_VPP_VCCB_VPP_PGM
A_SLOT_VCC
B_SLOT_VCC
O
m e g a
M i c r o
8 2 C 7 2 2 G X
Figure 5. The Omega Micro 82C722GX and two MIC256x-1 (or one MIC2563-1) adapt the ISA bus to two PCMCIAsockets.
12
12
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
VCC
VPP
VCC
VPP
Slot B
Slot A
3.3V 5V 12V
A_VCC_5 (8)A_VCC_3 (9)
A_VPP_VCC (7)A_VPP_PGM (6)
B_VCC_5 (12)B_VCC_3 (13)
B_VPP_VCC (11)B_VPP_PGM (10)
A_SLOT_VCC
B_SLOT_VCC
O m e g a
M i c r o
8 2 C 0 9 4
P C I t o P C M C I A
SCLK
SDATA
SLATCH
VCC_ACT_HIGH (2)
VPP_ACT_HIGH (4)
GND (14)
Omega Micro 82C28
VCC (28)
SCLK (19)
SDATA (18)
SLATCH (16)
10k Ω
10k Ω
VCC
The Omega Micro 82C28 convertsserial power control signals from the82C094 into standard MIC256x-0parallel logic.
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 8/10
Application Note 11 Micre
1997 2-77
Opti ControllersThe Opti 82C852 is logic compatible with Micrel “–1” optionlogic power controllers. Figure 7 shows a typical single-slotPC Card implementation using the Opti 82C852 and theMIC2560-1 power controller. The MIC2561-1 and MIC2562-1 are also directly compatible with the 82C852.
Figure 8 shows the Opti 82C824 dual-slot logic controllerinterfacing with the MIC2563A-1. Two MIC2560-1, MIC2561-1, or two MIC2562A-1 power controllers are also compatiblewith the 82C824.
MIC2563A-1BSM
VCC
VPP
3.3V 5V 12V
VCC_5V (pin 151)VCC_3V (pin 152)VPP_12 (pin 149)
VPP_3/5 (pin 150)
Slot A
VCC_5V (pin 7)
VCC_3V (pin 6)
VPP_12 (pin 9)
VPP_3/5 (pin 8)
7
6
5
4
3
2
11
10
12
13
14
8
9
28
27
26
15
16
17
18
19
20
21
22
23
24
25
VCC
VPP
Slot B
O p t i 8 2 C 8 2 4
Figure 8. The Opti 82C824 dual slot CardBus controller/docking station that works with the MIC2563 forming atwo-IC solution for two PC Card slots.
12
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-1BWM
VCC
VPP
3.3V 5V 12V
VCC_5V (pin 98)VCC_3V (pin 99)VPP_VCC (pin 1)VPP_PGM (pin 2)
O p
t i 8 2 C 8 5 2
Slot
Figure 7. The Opti 82C852 is a single slot PC Card logic controller that directly interfaces with Micrel MIC2560-1,MIC2561-1, or MIC2562-1 power controllers.
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 9/10
Application Note 11 Micrel
2-78 1997
Vadem ControllersThe MIC2560-0, MIC2561-0, MIC2562-0, and MIC2563-0are compatible with Vadem logic controllers, including theVG-365, VG-465, VG-468, and VG-469. The VG-365, VG-465, and VG-468 are straight forward implementations; the
VG-469 with its flexible voltage control scheme requires astrapping option for voltage control. Refer to Vadem’s designliterature for full details. Table 6 shows the VG-469 V CCstrapping options for positive pin polarity.
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
EN1 1
EN0 1
VDD
VCC 3/5
VCC EN
GND
7
6
5
4
3
2
11
10
12
13
14
15
16
8 9
VCC3 IN
VCC OUT
VCC5_EN
VCC3_EN
EN0
EN1 FLAG
N/C
VPP IN
VCC OUT
VCC5 IN
VPP OUT
VCC OUT
N/C
VCC3 IN
MIC2560-0BWM
V a
d e m
V G - 3
6 5
VPP 1_EN0
VPP 1_EN1
VPP 2_EN0VPP 2_EN1
VPP 1_EN0
VPP 1_EN1
VPP 2_EN0VPP 2_EN1
VCC _EN
VCC _EN
12
MIC2558
7
6
5
4
3
2
8
9
10
11
12
13
14
+5V +12V
VCC
VPP1
VPP2
VCC
VPP1
VPP2
Slot A
Slot B
Figure 7. A dual slot PC Card system using the Vadem VG-365 and the MIC256x-0.One MIC2563-0 may replace the two MIC2560-0 shown in this schematic.
Table 6. Vadem VG-469 flexible voltage control strapping scheme for the MIC2560-0,MIC2561-0, MIC2562-0, or the MIC2563-0.
D1 D0 V CC_EN1 VCC_EN0 VCC OUTReg 2F/6F Reg 2F/6F
1 0 0 0 Hi-Z1 1 0 1 3.3V
0 0 1 0 5V0 1 1 1 3.3V
7/30/2019 7400 Series Logic ICs
http://slidepdf.com/reader/full/7400-series-logic-ics 10/10
Application Note 11 Micre
1997 2 79
Serial-Interface Logic ControllersWith the advent of the CardBus option, logic controllers needmore and more pins to handle the extra functions. Some ofthe eight pins previously reserved for power control are nowemployed for these new functions. Converting from a parallelcontrol bus to a serial bus is one answer: this change frees up
Component KeyU1 ............. MIC2563U2, U3 ...... 74x175U4 ............. 74x574
Serial Control Adapter P.C. Board Layout
Serial Control
Figure 6 shows conversion from a three-wire serial interface,such as used by the Cirrus Logic CL-PD6730, to the standardeight-line parallel interface used by the MIC2563A-1. It iscompatible with any of Micrel’s “-1” controllers. This interfacerequires three common, low cost 7400-series logic ICs:
• 74x574 Octal D Flip-Flop• 74x175 Quad Flip-Flop with Latches
(two needed)Either 3.3V or 5V logic devices may be used, depending uponthe control voltage employed by the slot logic controller. Pinnumbers in parenthesis refer to the MIC2563A-1BSM.Gerber™ files for this P.C. board layout are available to Micrel
customers. Please contact Micrel directly.Another serial-to-parallel solution for this application is the74HC594, 8-bit shift register with output registers. This de-vice contains the eight D flip-flops plus has latched outputssuitable for this purpose.
to six pins. However; the control logic inside the powercontroller must be significantly more complex to handle serialdata protocols.Existing parallel bus power controllers may be adapted forserial control operation. A typical circuit consists of two mainblocks: a serial to-parallel converter and an eight-bit latch.
4 2
5 7
12 10
13 15
1 CLR 9 CLK
D QSER_DATA
SER_CLK
SER_LATCH
RST#
D Q
D Q
D Q
D Q
D Q
D Q
D Q
2
3
4
5
6
7
8
9
19
18
17
16
15
14
13
12
11
10
174x574
20
VCC
D Q
D Q
D Q
D Q
4 2
5 7
12 10
13 15
1 CLR 9 CLK
D Q
D Q
D Q
D Q
A_VPP_PGM (Pin 8)
A_VPP_VCC (Pin 7)
A_VCC5_EN (Pin 5)
A_VCC3_EN (Pin 6)
B_VPP_PGM (Pin 22)
B_VPP_VCC (Pin 21)
B_VCC3_EN (Pin 19)
B_VCC5_EN (Pin 20)
74x175
74x175
Figure 6. Interfacing the MIC2563A with a serial-output data controller. Pinouts shown are for the MIC2563A-1and a three-wire serial controller.