73188871 Lte Planning
Transcript of 73188871 Lte Planning
![Page 1: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/1.jpg)
![Page 2: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/2.jpg)
MARKET
![Page 3: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/3.jpg)
![Page 4: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/4.jpg)
![Page 5: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/5.jpg)
![Page 6: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/6.jpg)
201120102009200820072006200520042003200220012000
R99 R4 R5 R6 R7 R8 R9 R10
UM
TS
HS
PA
DL
HS
PA
UL
LT
E
LT
E
Ad
v
HS
PA
+
EP
C
Co
mm
on
IMS
IMS
MM
Te
l
3GPP Time Line and Evolution
![Page 7: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/7.jpg)
LTE Requirement (3GPP TR 25.913)
• Peak data rate 100 Mbps (DL) and 50 Mbps (UL) to 20 MHz
• Throughput increased by 3-4 times and 2-3 times for the downlink to uplink from HSDPA Rel 6 ( DL =
14.4 Mbps , to use transmitter sites that have been used in UTRA / GERAN
• Throughput increased by 3-4 times and 2-3 time UL = 5.7 Mbps )
• Spectrum efficiency by continuing as for the downlink to uplink from HSDPA Rel-
6 (DL = 14.4 Mbps, UL = 5.7 Mbps)
• Flexible use of spectrum (1.4, 3, 5, 10, 15, 20 MHz)
• Lower latency :
– Radio access network latency ( user plane UE – RNC- UE ) below 10 ms
• The ability of the use mobility up to 350 km / hour
• Coverage up to a radius of approximately 5 km
• Enhance MBMS ( Multimedia Broadcast / Multicast Service ) efficiency ( 1 bit/s/Hz)
• Retaining 3GPP RAT ( Radio Access Technology ) which already exist and support internetworking with
him.
• Architecture simplification , minimization and packet – based interface , full IP
![Page 8: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/8.jpg)
LTE Architecture
In the LTE network is divided into
2 basic network, namely:
1. E UTRAN (Evolved Universal
Terrestrial Radio Access Network)
2. EPC (Evolved Packet Core)
![Page 9: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/9.jpg)
SERVICE
The IP Multimedia Sub-System (IMS) is a good example of servicemachinery that can be used in the Services Connectivity Layer toprovide services on top of the IP connectivity provided by the lowerlayers.
For example, to support the voice service, IMS can provide Voice overIP (VoIP) and interconnectivity to legacy circuit switched networksPSTN and ISDN through Media Gateways it controls.
![Page 10: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/10.jpg)
EPC
• Functionally the EPC is equivalent to the packet switched domain of theexisting 3GPP networks.
• EPC consist of :
– MME ( Mobility Management Entity )
– SAE GW represents the combination of the two gateways, ServingGateway (S-GW) and Packet Data Network Gateway (P-GW)
– Home Subscriber Server (HSS)
– Policy and Charging Rules Function (PCRF)
( Evolved Universal Terrestrial Radio Access Network)
![Page 11: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/11.jpg)
Mobility Management Entity (MME)
– MME is a controller at each node on the LTE access network. At UEin idle state (idle mode), MME is responsible for tracking andpaging procedure which includes retransmission therein.
– MME is responsible for selecting SGW (Serving SAE Gateway)which will be used during initial attach EU and the EU time to dointra - LTE handover.
– Used for bearer control, a different view R99 / 4 which is stillcontrolled by the gateway
Policy and Charging Rules Function (PCRF)In order to handle QoS as well as control rating and charging, and billing
EPC Con’t
![Page 12: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/12.jpg)
Home Subscriber Server (HSS)For management and security subscriber, combination AUC and HLR
Serving SAE Gateway (SGW)
- Set the path and forwards the data in the form of packets of each user- As an anchor / liaison between the UE and the eNB at the time of the inter handover
- As a liaison link between the 3GPP LTE technology with the technology(in this case the 2G and 3G)
Gateway Packet Data Network (PDN GW)
- Provides for the UE 's relationship to the network packet- Provide a link relationship between LTE technology with technology non 3GPP (WiMAX) and 3GPP2 (CDMA 20001X and EVDO)
EPC Con’t
![Page 13: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/13.jpg)
E-UTRAN
Role of Radio Access Network (RAN), namely Node B and RNC is
replaced with ENB, so as to reduce operational and maintenance cost
of the device other than the simpler network architecture
E-nodeB functions : all radio protocols, mobility management, header
compression and all packet retransmissions
As a network, E-UTRAN is simply a mesh of eNodeBs connected to
neighboring eNodeBs with the X2 interface.
(Evolved Universal Terrestrial Radio Access Network)
![Page 14: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/14.jpg)
User Equipment
Functionally the UE is a platform for communicationapplications, which signal with the network for settingup, maintaining and removing the communication linksthe end user needs.
This includes mobility management functions such ashandovers and reporting the terminals location, and inthese the UE performs as instructed by the network
![Page 15: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/15.jpg)
FREQUENCY & BANDWIDTH IN LTE
![Page 16: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/16.jpg)
Key Consideration to Spectrum Selection
* Band Selection Source: 3GPP TS 36.101
![Page 17: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/17.jpg)
Illustration for Spectrum Selection
![Page 18: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/18.jpg)
Channel Bandwidth Flexibility
LTE provides channel bandwidth flexibility for operation in differently-sized
LTE supports paired and unpaired spectrum on the same hardware spectrum
![Page 19: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/19.jpg)
Channel Bandwidth Impact
![Page 20: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/20.jpg)
OFDM
![Page 21: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/21.jpg)
OFDM vs Single Carrier
Spectral efficiency of OFDM compared to classicalmulticarrier modulation: (a) classical multicarriersystem spectrum; (b) OFDM system spectrum.
![Page 22: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/22.jpg)
Motivation for OFDM Approaches• Advantages
– Efficient in the use of frequencies
– Highly scalable
– Overcome delay spread, multipath & frequency selective fading, and ISI
• Weaknesses– Frequency Offset
– Nonlinear Distortion (PAPR)
PAPR illustration
![Page 23: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/23.jpg)
OFDM Concept
• Multicarrier modulation/multiplexing technique• Available bandwidth is divided into several sub-channels• Data is serial-to-parallel converted• Symbols are transmitted on different sub-channels
![Page 24: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/24.jpg)
OFDM Block Diagram (Tx)
Diagram Block Contents:
• S/P Serial to Parallel Converter
• Sub-Carrier Modulator
• IFFT Inverse Fast Fourier Transform
• P/S Parallel to Serial Converter
• DAC Digital to Analog Converter
![Page 25: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/25.jpg)
OFDM Block Diagram (Rx)
Diagram Block Contents:
• S/P Serial to Parallel Converter
• Sub-Carrier Modulator
• IFFT Inverse Fast Fourier Transform
• P/S Parallel to Serial Converter
• DAC Digital to Analog Converter
![Page 26: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/26.jpg)
Cyclic Prefix• Useful for multipath delay spread• Guard Interval (cyclic prefix) : short & long
![Page 27: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/27.jpg)
Type of Cyclic Prefix
![Page 28: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/28.jpg)
OFDMA & SC-FDMA
![Page 29: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/29.jpg)
OFDMA vs. SCFDMA Definition
OFDMA is a multiple access technique based on OFDM as the modulation technique. It is used for DL transmission in LTE
SC-FDMA is a hybrid UL transmission scheme in LTE which has single-carrier transmission systems with the long symbol time and flexible frequency allocation of OFDM.
![Page 30: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/30.jpg)
SC-FDMA Diagram Block
SC-FDMA frequency-domain transmit processing (DFT-S-OFDM) showing localized and distributed subcarrier mappings.
![Page 31: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/31.jpg)
Type of OFDMA Sub-Carrier
Data sub-carrier
– Carry QPSK, 16 QAM, 64 QAM symbol
Pilot sub-carrier
– It is used to facilitate channel estimation and coherent demodulation at the receiver
Null sub-carrier
– Guard sub-carrier
– DC sub-carrier
![Page 32: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/32.jpg)
Subcarrier Mapping
(Npilot -2)/2 Nsubcarrier data / 2
PIL
OT
Nsubcarrier data / 2 Npilot /2
BW
Nsubcarrier data See slide #19 or 3GPP TS 36.104Npilot NFFT-Point - Nsubcarrier data
![Page 33: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/33.jpg)
MULTI ANTENNA TECHNIQUE
![Page 34: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/34.jpg)
Multiple Antenna Technique
Existing Tech Smart Antenna MIMO Antenna
![Page 35: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/35.jpg)
Multiple Antenna Technique Two popular techniques in MIMO wireless systems:
Spatial Diversity: Increased SNR• Receive and transmit diversity
mitigates fading and improves link quality
Spatial Multiplexing: Increased rate• Spatial multiplexing yields
substantial increase spectral efficiency
![Page 36: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/36.jpg)
Spatial DiversityTransmit Diversity
• Space-time Code (STC): Redundant data sent over time and space domains (antennas).
• Receive SNR increase about linearity with diversity order NrNt
• Provide diversity gain to combat fading
• Optional in 802.16d (2x2 Alamouti STBC), used in 3G CDMA
![Page 37: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/37.jpg)
Spatial Multiplexing
MIMO Multiplexing
• Data is not redundant – less diversity but less repetition
• Provides multiplexing gain to increase data-rate
• Low (No) diversity compared with STC
![Page 38: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/38.jpg)
LTE SUPPORTING TECHNOLOGIES
HARQ
AMC
![Page 39: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/39.jpg)
HARQ
HARQ or retransmission scheme in LTE use stop-and-wait retransmission system.
![Page 40: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/40.jpg)
Adaptive Modulation
SNR-CQI Mapping for BLER 10%
Adaptive Modulation Illustration
![Page 41: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/41.jpg)
Constellation DiagramQPSK
16 QAM
64 QAM
![Page 42: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/42.jpg)
Adaptive Modulation and Coding
Standard for CQI mapping
![Page 43: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/43.jpg)
Scheduling
![Page 44: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/44.jpg)
Control PlaneControl Plane (C-Plane) is use to describe the protocols that convey information from the DTE to the end user (the control) of a node, or between nodes in the network to conveying required information to set, control and clearing the connection protocol.
User plane (U-plane) is a protocol used directly in the transfer of user data from the DTE (Data Terminal Equipment) to the other end-users. U-plane provides the function of delivery or transfer user information, and include all relevant mechanisms of information transfer such as flow control and error recovery. In the user plane used approach layer .
User Plane
![Page 45: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/45.jpg)
CONTROL PLANE
![Page 46: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/46.jpg)
USER PLANE
![Page 47: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/47.jpg)
LTE CHANNELS
![Page 48: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/48.jpg)
LTE Layer Mapping
![Page 49: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/49.jpg)
Layer Function• Radio Link Control Layer (RLC)
> Retransmission
> Segmentation
• Medium Access Control Layer (MAC)
> Uplink and downlink scheduling at the eNodeB
> HARQ
• Physical Layer (PHY)
> Modulation/demodulation
> Coding/decoding
![Page 50: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/50.jpg)
LTE Downlink Channel Mapping
![Page 51: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/51.jpg)
LTE Downlink Logical Channels
• Paging Control Channel ( PCCH)> A downlink channel that transfers paging information and system
information change notifications.> This channel is used for paging when the network does not know
the location cell of the UE
• Broadcast Control Channel (BCCH)> Provides system information to all mobile terminals connected to
the eNodeB.> A downlink channel for broadcasting system control information
• Common Control Channel (CCCH)
> Channel for transmitting control information between UEs andnetwork.
> This channel is used for UEs having no RRC connection with thenetwork.
![Page 52: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/52.jpg)
• Multicast Control Channel (MCCH)> A point-to-multipoint downlink channel used for transmitting MBMS
> Control information from the network to the UE, for one or severalMTCHs.
> This channel is only used by UEs that receive MBMS
• Dedicated Control Channel (DCCH)> A point-to-point bi-directional channel that transmits dedicated
control information between a UE and the network.
> Used by UEs having an RRC connection
> This control channel is used for carrying user-specific controlinformation, e.g. for controlling actions including power control,handover, etc..
LTE Downlink Logical Channel Con’t
![Page 53: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/53.jpg)
LTE Downlink Logical Channel Con’t
• Multicast Traffic Channel (MTCH)
> A point-to-multipoint downlink channel for transmitting traffic data
from the network to the UE.
> This channel is only used by UEs that receive MBMS
• Dedicated Traffic Channel (DTCH )
> A point-to-point channel, dedicated to one UE, for the transfer of
user information.
> A DTCH can exist in both uplink and downlink
![Page 54: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/54.jpg)
LTE Downlink Transport Channel
• Paging Channel ( PCH)> Supports UE discontinuous reception (DRX) to enable UE power
saving
> Broadcasts in the entire coverage area of the cell;
> Mapped to physical resources which can be used dynamically alsofor traffic/other control channels.
• Broadcast Channel ( BCH )
> The LTE transport channel maps to Broadcast Control Channel
(BCCH)
> Fixed, pre-defined transport format
> Broadcast in the entire coverage area of the cell
![Page 55: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/55.jpg)
• Multicast Channel ( MCH)
> Broadcasts in the entire coverage area of the cell;
> Supports MBSFN combining of MBMS transmission on multiple cells;
> Supports semi-static resource allocation e.g. with a time frame of a longcyclic prefix
• Downlink Shared Channel ( DL-SCH )
> Main channel for downlink data transfer. It is used by many logical channels.
> Supports Hybrid ARQ
> Supports dynamic link adaptation by varying the modulation, coding and transmit power
> Optionally supports broadcast in the entire cell;
> Optionally supports beam forming
> Supports both dynamic and semi-static resource allocation
> Supports UE discontinuous reception (DRX) to enable UE power saving
> Supports MBMS transmission
LTE Downlink Transport Channel Con’t
![Page 56: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/56.jpg)
LTE Downlink Physical Channel
• Physical Downlink Shared Channel ( PDSCH)
> This channel is used for unicast and paging functions
> Carries the DL-SCH and PCH
> QPSK, 16-QAM, and 64-QAM Modulation
• Physical Downlink Control Channel ( PCSCH)> Informs the UE about the resource allocation of PCH and DL-SCH,
and Hybrid ARQ information related to DL-SCH
> Carries the uplink scheduling grant
> QPSK Modulation
![Page 57: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/57.jpg)
Uplink Physical Channels
• Physical HARQ Indicator Channel (PHICH)
> Used to report the Hybrid ARQ status
> Carries Hybrid ARQ ACK/NAKs in response to uplink transmissions.
> QPSK Modulation
• Physical Braodcast Channel (PBCH)
> This physical channel carries system information for UEs
requiring to access the network.
> QPSK Modulation
![Page 58: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/58.jpg)
LTE Uplink Channels
![Page 59: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/59.jpg)
Uplink Physical Channels
• Physical Radio Access Channel ( PRACH)> for random access functions
• Physical Uplink Shared Channel ( PUSCH)> Carries the UL-SCH> QPSK, 16-QAM, and 64-QAM Modulation
• Packet Uplink Control Channel ( PUCCH)
> Sends Hybrid ARQ ACK/NAKs
> Carries Scheduling Request (SR)> Carries CQI reports> BPSK and QPSK Modulation
![Page 60: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/60.jpg)
Uplink Transport Channels
• Random Access Channel (RACH)
> Channel carries minimal information
> Transmissions on the channel may be loss due to collisons
• Uplink Shared Channel ( UL–SCH )
> Optional support for beam forming
> Support HARQ
![Page 61: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/61.jpg)
Uplink Logical Channels
• Common Control Channel ( CCCH)> Channel for transmitting control information between Ue and
network.> This channel is used for UEs having no RRC connection with the
network.
• Dedicated Control Channel ( DCCH)> A point-to-point bi-directional channel that transmits dedicated control
information between a UE and the network.> Used by UEs having an RRC connection.
• Dedicated Traffic Channel ( DTCH)
> A point-to-point channel, dedicated to one UE, for the transfer of userinformation.
> A DTCH can exist in both uplink and downlink.
![Page 62: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/62.jpg)
![Page 63: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/63.jpg)
LTE FRAME STRUCTUR> Functions
System can maintain synchronization and manage the different type of information that need to be carried between the eNodeB and UE
> LTE frame structure consist of 1. FDD ( Frequency division duplex)2. TDD ( Time division duplex )
> A radio frame has duration of 10 ms> A resource block spans 12 subcarriers over a slot duration of 0.5 ms> BW RB = 180 KHz> BW Subcarrier = 15 kHz
![Page 64: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/64.jpg)
FDD Frame structure
![Page 65: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/65.jpg)
TDD Frame Structure
DwPTS : Downlink Pilot Time SlotGP : Guard PeriodUpPTS : Uplink Pilot Time Slot.
![Page 66: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/66.jpg)
LTE TDD Sub Frame Allocations
D : sub frame for downlink transmissionS :"special" sub frame used for a guard timeU : sub frame for uplink transmission
![Page 67: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/67.jpg)
Planning Coverage
![Page 68: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/68.jpg)
Downlink Link Budget LTE Unit Value Info
Data Rate kbps 1000
Transmitter - eNodeBa. Tx Power dBm 46 a
b. Tx Antenna Gain dB 18 b
c. Loss System dB 3 cd. EIRP dBm 61 a+b+c
Receiver - UE
e. Ue Noise Figure dB 7 ef. Thermal Noise dBm -102.7 k*T*B
g. SINR dB -5 g
h. Receiver Sensitivity dBm -100.7 e+f+gi. Interference Margin dB 3 i
j. Control Channel Overhead dB 1 j
k. Rx antenna gain dBi 0 kl. Body Loss dB 0 l
MAPL dB 157.7 d-h-i-j+k-l
MAPL Calculation
![Page 69: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/69.jpg)
Propagation Model• LTE – 700 MHz
– Okumura-Hatta
• LTE – 2100 MHz
– Cost 231-Hatta
• LTE – 2600 MHz
– SUI
MTRTcp C)logd6,55logh(44,9)a(hlogh13,82)(logf33,946,3L
(d/100) log 47.9 109.78 Lp
d log hB] log 6,55– [44,9 CH - hB log 13,82– f log 26,16 69,55 Lp
![Page 70: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/70.jpg)
Pathloss SUI
Lp = 109.78 + 47.9 log (d/100)
78.109)100/log(9.47 Lpd
9.47/)78.109()100/log( Lpd9.47/)78.109(10)100/( Lpd
9.47/)78.109(10100 Lpxd9.47/)78.1097.157(10100 xd
00042.110100xd
966.1000d meters
![Page 71: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/71.jpg)
Radius Calculation
L = 2,6 d2
L = 1,95 . 2,6 . d2
L = 1,3 . 2,6 . d2
![Page 72: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/72.jpg)
Radius Calculation
L = 2,6 d2L = 1,95 . 2,6 . d2
2(1) x 2.6 L
2.6 L
2(1) x 2.6 x 1.95 L
5.07 L 2km 2km
For Omni directional For trisectoral
![Page 73: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/73.jpg)
Number of eNodeB
• Urban Area (Trisector)
– total area 242.928
–
–
2km
07.5/928.242eNodeBN
48eNodeBN
![Page 74: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/74.jpg)
PLANNING CAPACITY
![Page 75: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/75.jpg)
Calculation steps:
1. Number of user
2. User density
3. Services and Type
4. Penetration : building, vehicular, pedestrian
5. BHCA and call duration
6. OBQ
7. Site calculation
![Page 76: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/76.jpg)
Number of User
Where:
• Un : num of user on year ‘n’• Uo : initial num of user (based on urban/sub-urban)• a : percent of cellular user (%)• b : penetration of operator A (%)• d : Percent of LTE user • N : num of civilian in the object area• gf : num of user growth factor• n : planned year• u/sub : urban or sub-urban penetration (%)
Uo is Uou or UosubUosub = sub x UoN
Uou = u x UoN
Un = Uo (1 + gf)n
UoN = a x b x d x N
![Page 77: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/77.jpg)
Customer Prediction ParameterEx :
• Population = 1445892 people
• Cellular penetration = assumption 80%
• LTE penetration = assumption 10 %
• LTE provider A penetration = assumption 50 %
User prediction in 5th years
• U5 = 57835 ( 1 + 0.05 )5 assumption fp=5%
= 73814 user
Population 1445892 people
Customer cellular (80%) 1156713 user
Customer LTE (10%) 115671 user
Customer LTE provider A (50%) 57835 user
![Page 78: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/78.jpg)
Example User Calculation
Ex :• urban penetration = assumption 60 %
• suburban penetration = assumption 40 %
• Urban user = 73814 x 60 % = 44288 user
• Suburban user = 73814 x 40 % = 29525 user
![Page 79: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/79.jpg)
User Density
• Lu : urban area wide
• Lsub : sub-urban area wide
• L : object area wide
• Cu : Urban area density
• Csub : sub-urban area density
Lu = L x u Lsub = L x sub
Cu = Un/ Lu Csub = Un/Lsub
![Page 80: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/80.jpg)
Example User Density Calculation
Ex :• urban area penetration = assumption 40 %
• suburban area penetration = assumption 40 %
• Openarea = assumption 20 %=>
Urban area wide (Lu) : 242,928 km2
Sub-urban area wide (Lsub) : 242,928 km2
=>Cu = 44288 / 242,928 = 182,31232 user/km2
Csub = 29525 / 242,928 = 121,54155 user/km2
![Page 81: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/81.jpg)
Services and Type
• Services (Rb)– VoIP : 64 kbps
– FTP : 1000 kbps
– Video : 384 kbps
• Type (c)– Building : 50 %
– Vehicular : 30 %
– Pedestrian : 20 %
![Page 82: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/82.jpg)
• Penetration (p) per type per servicee.g: BUILDING VoIP usage penetration = 0.5
BUILDING FTP usage penetration = 0.4PEDESTRIAN Video usage penetration = 0.3
• BHCA (B) per type per servicee.g: BUILDING VoIP usage penetration = 0.008
BUILDING FTP usage penetration = 0.009PEDESTRIAN Video usage penetration = 0.008
• Call duration (h) per type per service (ms)e.g: BUILDING VoIP usage penetration = 60
BUILDING FTP usage penetration = 50PEDESTRIAN Video usage penetration = 50
![Page 83: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/83.jpg)
service net user bit rate (Rb)
VoIP 64000
FTP 1000000
Video 384000
typecall duration (h)
voip video ftp
building 60 40 50
pedestrian 60 50 70
vehicular 60 40 80
BHCA (B)
Service Building Pedestrian Vehicular
Voip 0,008 0,008 0,009
Video 0,007 0,008 0,009
FTP 0,009 0,008 0,008
Penetrasi User (p)
Building Pedestrian Vehicular
Voip 0,5 0,5 0,2
Video 0,3 0,3 0,2
FTP 0,4 0,4 0,3
![Page 84: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/84.jpg)
OBQ (Offered Bit Quantity)• VoIP
OBQT = cT x Cu; T x pT x RbVoIP x BT x hT
• FTP OBQT = cT x Cu; T x pT x RbFTP x BT x hT
• VideoOBQT = cT x Cu; T x pT x RbVid x BT x hT
Note: if T= pedestrian, then “OBQT “ is pedestrian OBQ, “BT “ is pedestrian BHCA, etc.
T : Type (Building; Vehicular; Pedestrian)
![Page 85: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/85.jpg)
OBQ cont’d
Where:
OBQVoIP = OBQvehicular + OBQbuilding + OBQ pedestrian
OBQFTP = OBQvehicular + OBQbuilding + OBQ pedestrian
OBQVideo = OBQvehicular + OBQbuilding + OBQ pedestrian
OBQ total = OBQVoIP + OBQFTP + OBQVideo
![Page 86: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/86.jpg)
OBQtotal= 20,74860049 + 13,97825 + 8,260936 = 42,98779
OBQ
Service Building Pedestrian Vehicular
Voip 1,400158616 0,5600634 0,252029
Video 2,940333094 5,2505948 1,008114
FTP 16,40810878 8,1675919 7,000793
∑ 20,74860049 13,97825 8,260936
OBQ cont’d
![Page 87: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/87.jpg)
eNodeB Capacity
ms
NxxN
Hz
bitMbpsePeakBitRat
subframepersymbol
ssubcarrier1
][
Bandwidth (MHz)Modulation
QPSK 16 QAM 64 QAM
1.4 2.016 Mbps 4.032 Mbps 6.048 Mbps
3 5.04 Mbps 10.08 Mbps 15.12 Mbps
5 8.4 Mbps 16.8 Mbps 25.2 Mbps
10 16.8 Mbps 33.6 Mbps 50.4 Mbps
15 25.2 Mbps 50.4 Mbps 75.6 Mbps
20 33.6 Mbps 67.2 Mbps 100.8 Mbps
![Page 88: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/88.jpg)
Site Calculation• Site (L)
L = (50.4 x 3) / OBQtotal
= (50.4 x 3) / 42,98779 = 3,5172778 km2
• Radius (d)
d = (L / 2.6 / 1.95) ^ 0.5
= (3,5172778 / 2.6 / 1.95) ^ 0.5 = 0,832912489 km
50.4 Mbps ---> (asumption: using 64 QAM 1/1, BW = 10 MHz)
![Page 89: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/89.jpg)
Site Calculation Con’t
• Number of eNodeB (M)
M = Lu / L
= 242,928 km2 / 3,5172778 km2
= 69,06704366
We use “Lu” JUST IN CASE we count urban capacity only
![Page 90: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/90.jpg)
LTE Simulation Using Atoll
![Page 91: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/91.jpg)
Getting Started with Atoll
New -> From a
Document
Template
Choose LTE
workspace
![Page 92: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/92.jpg)
Setting Project Area
It is used to display the project area from the map raster.
To set the coordinate type and the area displayed on the worksheet.
![Page 93: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/93.jpg)
Import Raster Map
raster is a contour map based on the topography of the area. Raster consist of clutter map, height map and vector map
![Page 94: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/94.jpg)
Import Raster Map Con’t
Clutter index -> Clutter Classes
Height index ->Altitude
Vector index ->Vectors
![Page 95: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/95.jpg)
Frequency Band
frequency bands and can beseen in the LTE specification3GPP.org
![Page 96: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/96.jpg)
Antenna Polarization Model
add the appropriate antenna used
![Page 97: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/97.jpg)
Antenna Polarization Model
![Page 98: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/98.jpg)
Setting Feeder
To setting feeder & connector loss at eNode B equipment
![Page 99: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/99.jpg)
Setting Transmitter Frequency Bandafter determining the frequency band, set the transmitter frequency as the frequency and morpho class used
![Page 100: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/100.jpg)
Setting Transmitter Frequency Band Con’t
![Page 101: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/101.jpg)
EnvirontmentDelete user
Delete environtment
![Page 102: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/102.jpg)
Delete User ProfileDelete service thensetting service type
![Page 103: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/103.jpg)
ServicesDelete service then setting service type Edit Service
![Page 104: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/104.jpg)
Service
VoIP Video FTP
![Page 105: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/105.jpg)
Add User Profile
Assumption throughput user = 50 kbps
![Page 106: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/106.jpg)
Add User Profile
Pedestrian
Vehicular
![Page 107: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/107.jpg)
Add Environtment
![Page 108: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/108.jpg)
Plotting eNode B
eNode B can be in place based on planning calculation or the use of existing nodeB or BTS
![Page 109: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/109.jpg)
Make a Prediction
make predictions based on measured
fill of the receiver sensitivity specification
Click calculate
![Page 110: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/110.jpg)
Coverage by Signal Level
![Page 111: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/111.jpg)
Result Histogram and CDF Chart
![Page 112: 73188871 Lte Planning](https://reader034.fdocuments.us/reader034/viewer/2022050721/55cf9d7f550346d033addfce/html5/thumbnails/112.jpg)
Reference
[1] Abdul Basit, Syed. Dimensioning of LTE Network Description ofModels and Tool, Coverage and Capacity Estimation of 3GPPLong Term Evolution radio interface. 2009.
[2] Coverage and Capacity Dimensioning Recommendation:Ericsson. 2009.
[3] Holma, Harri and Antti Toskala. WCDMA for UMTS – HSPAEvolution and LTE. John Willey and Son: 2007.
[4] 3GGP. TS 36.XXX “LTE TS Group Series”. 2009.