703N
Transcript of 703N
-
8/10/2019 703N
1/21
TL-WR703N setup guide one 3G router mode
TL-WR703NIs a new generation of mini 3G wireless router, compatible with the mainstream 3G standard - CDMA2000 (China
Telecom), WCDMA (China Unicom), TD-SCDMA (China Mobile). By using the device to meet people to share 3G wireless
broadband purposes.
Here we introduce the 3G TL-WR703N routing mode configuration.
TL-WR703NQuick setup:
Set by the Setup Wizard
Open the Device Management page "192.168.1.1", click "Setup Wizard", select "Next", optional equipment, there are three
access modes: 3G router mode, the wireless router mode, the wireless AP mode, the default route for the 3G model.
Here we choose "3G router mode", click "Next", 3G dial-up configuration parameters, select the region "China", the mobile ISP:
optional, "China Telecom", "China Mobile" and "China Unicom" (according to your Internet card formats to choose), the other
default settings do not change.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
2/21
TL-WR703NDefault has built in China Telecom, China Unicom mobile and dial the relevant parameters, in general, as
shown in the figure need only select the ISP operator interface can be automatically set to dial numbers, APN user name and
password and other information.
Click "Next" to set the wireless security.
Wireless Status: Wireless router, you must choose to open, so that the wireless network can access and host access to the
entire network.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
3/21
-
8/10/2019 703N
4/21
TL-WR703N setting guide TwoWireless router mode
Under router modeTL-WR703Nis equivalent to a wireless router, wired port as a WAN port, wireless-LAN, all the wireless
clients can share a broadband Internet line. The typical network application structure as shown below.
Here TL-WR703N Router Quick Setup mode method.
One: TL-WR703N settings
Step 1: In the browser, enter "192.168.1.1", enter the login ID and password are admin, open the TL-WR703N management
interface, automatic pop-up "Setup Wizard" (the management interface can also click the menu "Setup Wizard"), as shown
below.
Step 2: Click "Next" to start setting up the wireless mode setting page as shown below.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
5/21
Step 3: Select the "Router", click Next to bring up the wireless settings page, as shown below.
Step 4:: According to the decision to choose the front-end broadband connections to the Internet the way, if you can enter
recommended items. In this case the PPPOE example.
Step 5: Enter the broadband "Internet Account" and "Internet password", hit "Next", as shown below.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
6/21
AS shown on the above page, you can set TL-WR703N the SSID (wireless network name that TP-LINK_531984). To prevent
unauthorized users rub network, it is recommended to set the wireless security is recommended to select
"WPA-PSK/WPA2-PSK" and set the PSK password (in this case 123456789).
Step 6: Click "Next" prompt to restart the device, as shown below.
Click "Restart", automatically restarting the router, setup is complete.
Step 7: Restart completed at this time TL-WR703N wireless network already set up wireless security, the computer's wireless
network connection is automatically disconnected, reconnect the TL-WR703N need a wireless network (in this case the SSID to
TP-LINK_531984), the connection process to enter TL-WR703N wireless PSK password (in this case 123456789), connected
to, the following figure.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
7/21
If "WAN port state" view has access to the router to the IP and DNS server address, the PPPoE dial-up success.
Thus TL-WR703N the Router mode has been configured, and successfully connected to the Internet, wireless networks have
been set WPA-PSK/WPA2-PSK wireless security. Computer has wireless connectivity to the Internet router, the other computer
simply connect the TL-WR703N can normally access.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
8/21
TL-WR703N Setup guide ThreeWireless AP mode
AP mode using the wireless coverage capabilities for traditional wired LAN to provide wireless access to extension.
First, connect TL-WR703Nwith front-end wired LAN connections, wireless device sends the wireless signal coverage to meet
the extended family and small and medium wireless access.
Here we introduce the TL-WR703N wireless AP mode configuration.
TL-WR703NSetting:
Step 1: Connect to TL-WR703N. As the TL-WR703N in AP mode, the default DHCP server is not open, the computer can not
automatically assign IP addresses, so you need to configure the wireless network to connect the computer's IP address in order
to visit the router management interface. Computer wireless network connection IP address is set to 192.168.1.X (1 X 252),
subnet mask: 255.255.255.0, as shown below. After setup is complete, click "OK" to take effect. TL-WR703N default
management IP address "192.168.1.1".
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
9/21
Note: The computer's IP address configuration can refer to the following link:
http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72
Step 2TL-WR703N did not set the default wireless security. Computer through a wired or wireless connection to TL-WR703N
(in xp system to TL-WR703N wireless connection for example), scan the environment in the wireless network, select the
TL-WR703N wireless SSID, and click "Connect" to connect the later, as shown below.
Step 3: In the browser, type "192.168.1.1", enter the login user name and password are admin, open the TL-WR703Nmanagement interface, automatic pop-up "Setup Wizard" (the management interface can also click the menu "Setup Wizard") ,
as shown below.
Step 4: Click "Next" to start setting up mode settings page, select "wireless AP mode" as shown below.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
10/21
-
8/10/2019 703N
11/21
Step 8: Restart completed at this time TL-WR703N wireless network already set up wireless security, the computer's wireless
network connection is automatically disconnected, reconnect the TL-WR703N need a wireless network (in this case the SSID to
TP-LINK_531984), the connection process to enter TL-WR703N wireless PSK password (in this case abcdefgh), connected to,
the following figure.
Step 9: After configuration is complete, the IP address of your wireless network connection to re-set to the original configuration
(usually automatically obtain an IP address), click "OK" effect, in order to properly connect to the Internet, as shown below. .
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
12/21
Note: TL-WR703N default management IP address "192.168.1.1", it must be TL-WR703N the LAN IP address set to the wired
LAN devices are not all the same IP address to prevent IP address conflicts (under normal circumstances do not change). In the
menu "network parameters" - "LAN port settings", change IP, click the "Save", the router automatically restart. As shown below.
Thus TL-WR703N AP mode configuration is completed, then the computer search to TL-WR703N issued wireless SSID is
TP-LINK_531984, PSK key is abcdefgh.
TL-WR703N Setup guide FourThe wireless network wireless AP mode
TL-WR703N in wireless applications, has the following three application modes: wireless AP mode, the wireless router mode, 3G
wireless routing model, this paper focuses on the wireless AP mode, an introduction to a variety of applications. Mode and 3G
wireless router wireless router mode, please refer to other relevant documents.
Time during the Setup Wizard, select the wireless AP mode, according to the need to select all in AP mode working application
mode, as shown below:
As the TL-WR703N in AP mode, the default DHCP server is not open, the computer can not automatically assign IP addresses,
so you need to configure the wireless network to connect the computer's IP address in order to visit the router management
interface.
Computer wireless network connection IP address is set to 192.168.1.X (1 X 252), subnet mask: 255.255.255.0, as shown
below. After setup is complete, click "OK" to take effect. TL-WR703N default management IP address "192.168.1.1".
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
13/21
Note: The computer's IP address configuration can refer to the following link:
http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72
OneHere we introduce the TL-WR703N wireless AP mode, repeater mode (Repeater) under the application.
TL-WR703Nsetting
Step 1: Click relay mode (Repeater), the display as shown below
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
14/21
Step 2: Fill in the remote AP's ssid, mac address or click the scan, in which the pop-up list to select the front end relay to connect
to the SSID of the router, and enter the front of the router with the same encryption type and key.
Step 3: Click Next, restart the computer to take effect.
TwoHere we introduce the TL-WR703N wireless AP mode, client mode (Client) under the application.
TL-WR703Nsetting
Step 1: Click to select client mode (Client), the pop-up as shown below:
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
15/21
Step 2: Manually enter the front-end router's SSID, or scan the list and click Connect, and select the front-end router with the
same encryption method, enter the correct password. As shown below:
Step 3: Click Next, restart the computer to take effect.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
16/21
ThreeHere we introduce the TL-WR703N wireless AP mode, Bridge mode (Bridge with AP) under the application.
TL-WR703Nand 11g router wireless bridge configuration1.
Note: TL-WR703N in the choice of bridge mode (Bridge with AP), supports the following encryption types: WEP, no encryption,without modifying the wireless security settings. (For this example select WEP for wireless encryption)
In this case 11g router TL-WR541G +, for example, the network topology is as follows:
The following picture shows the TL-WR541G + user interface, set the wireless parameters to specify the channel 6, open the
bridge feature of the bridge on the side and fill in the TL-WR703N device MAC address, and open the security settings, as
shown below:
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
17/21
Below into the TL-WR703N wireless configuration interface configuration:
Step 1: Go to bridged mode, as shown:
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
18/21
Step 2: Scan the pop-up list and choose to connect to the network SSID, as shown:
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
19/21
Step 3: click Next, you need to reboot the router to take effect.
Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they should be TL-WR703N the
LAN IP address set to the wired LAN devices are not all the same IP address (in general under no change) can be in the menu
"network parameters" - "LAN port settings", change IP, click the "Save", the router automatically reboot as shown below.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
20/21
TL-WR703Nand 11n wireless router bridge configuration
In this case the TL-WR740N with TL-WR703N bridge, for example.
In the TL-WR703N and 11n wireless bridge products, only need to open the 11n products on the TL-WR703N WDS function toscan and connect, of course, need to maintain the same channel, encryption type, key.
Step 1: First you need to configure TL-WR703N wireless parameters, for example here is a designated channel, the wireless
security settings, encryption type and key support WEP, WPA-PSK/WPA2-PSK encryption, WEP encryption, for example here is
Step 2: TL-WR740N wireless WDS opens, set the following:
Click scan, in which the pop-up list select TL-WR703N the SSID, and select TL-WR703N the same encryption type and enter
the correct key, as shown:
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html
21 11/4/2012 2:33
-
8/10/2019 703N
21/21
Click Save, the following window appears, can be completed:
Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they should be TL-WR703N the
LAN IP address set to the wired LAN devices are not all the same IP address (in general under no change) can be in the menu
"network parameters" - "LAN port settings", change IP, click the "Save", the router automatically reboot as shown below.
http://dc311.4shared.com/doc/IpDL_-oJ/preview.html