7000IC Technical Specification L iners Vibrating Units Pre -screen Grizzly *All drawing dimensions...
Transcript of 7000IC Technical Specification L iners Vibrating Units Pre -screen Grizzly *All drawing dimensions...
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
PORTAFILL 7000IC TECHNICAL SPECIFICATION
IMPACT CRUSHER
Rotor 4 Blow Bar
Crusher Opening 810 x 600mm (32” x 24”)
Rotor Diameter 800mm (32”)
Rotor Width 750mm (29”)
Crusher Drive Direct Drive from Engine via Belts
Crusher Overload Protection Yes
Dust Suppression Impact Damper
Impact Block
Clamping Wedge
Dust Suppression
Impact Damper Wear Liners Short Blow Bar Long Blow Bar
Rubber Curtain
Chain Curtain
Belt Tension Wheel
Inlet Wear Bar
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
IMPACT CRUSHER
Crusher Gap Setting Manual
Recommended Maximum Crusher Gap 100mm (4”)
Recommended Minimum Crusher Gap 30mm (1 ¼”)
Further Adjustment Gap can be adjusted depending on material
Maximum Lump Size 400 x 400mm (16” x 16”) depending on material
Blow Bar Weight 140kgs (310lbs)
Rotor Speed 600-700rpm
Wear Liners 15mm (5/8”) thick
Main Crusher Body
Dust Suppression
Inspection Cover
Crusher Hinged Section
Jam Release Mechanism
Crushing Gap Adjustment
Crusher Bearings
Inspection Cover
Crusher Open Close Ram
Inspection Cover
Rubber Curtain
Blow Bar Change Arm
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
FEEDER
Feeder Length and Width 3868 x 1977mm (12’8” x 6’6”)
Hopper Capacity 1.8m3 (2.3 cu. yd.)
Pre-screening Grid Length and Width 1000 x 700mm (40” x 28”)
Pre-screening Discharge Onto Main Conveyor
Vibration Source Twin Hydraulic Vibrating Units
Vibration Angle Patented design to change angle of throw
Feed to Crusher Control Load Management on Feeder
CONVEYOR
Belt Width 900mm (36”)
Discharge Height 2720mm (8’11”)
Folding Mechanism Hydraulic Folding for Transport
Construction Impact Bed Under Crusher
Belt Type Smooth or Cleated Belt
Hardox Liners
Vibrating Units
Pre-screen Grizzly
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
POWER
Engine JCB 4 Cylinder Diesel
Emissions Type EU Stage IIIB Tier 4 Interim
Power 120Kw (160HP) @ 2150rpm
Operating Range 1800-2150rpm
Cooling Type Water Cooled
Typical Fuel Consumption 12-14 litres per hour (3 US Gallons per hour)
Fuel Tank Capacity 200 litres (52 US gallon)
Air Filter Scavenger Air Filter
OPTIONAL EXTRAS
• Closed loop recirculating screen and conveyor (Patent folding action)
• Dust suppression
• Dust covers on conveyors
• Radio tracking remote
• Belt magnet on main conveyor
• Digital belt scales
7000IC-R SPECIFICATIONS
Screen Size Length x Width 3180 x 1125mm (10’ 5” x 3’ 8”)
Number of Decks Single
Fines Conveyor Belt Width 900mm (36”)
Fines Conveyor Discharge Height 2500mm (8’2”)
Transfer Conveyor Belt Width 600mm (24”)
Returns Conveyor Belt Width 500mm (20”)
Folding Mechanism Hydraulic Folding for Transport
Remove for Transport No
WEIGHT
• 7000IC 19,000kgs (41,880lbs)
• 7000IC-R 24,000kgs (52,900lbs)
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
Working Dimensions 7000IC
Transport Dimensions 7000IC
2900
(9’6”)
12000 (39’3”)
2510
(8’2”)
2539
(8’3”)
2270 (7’5”)
9438 (31’)
2539
(8’3”)
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
Working Dimension 7000IC-R (Closed Circuit)
Working Dimension 7000IC-R (Open Circuit)
2500
(8’2”)
3760
(12’4”)
13957 (45’8”)
5280
(17’3”)
13957 (45’8”)
3277
(10’7”)
*All drawing dimensions approximate and in millimetres and feet and inches. Portafill International
reserves the right to alter the specification of these machine without notice.
Transport Dimension 7000IC-R (40ft HC Container)
ISO Image 7000IC-R
11886 (38’11”)
2330 (7’6”)
2566
(8’4”)
2566
(8’4”)