65136 Kubota D722 injector pump repair€¦ · The Injector pump Avant p/n 65136, Kubota p/n...
Transcript of 65136 Kubota D722 injector pump repair€¦ · The Injector pump Avant p/n 65136, Kubota p/n...
1
Kubota D 722 injector pump repair
2
Kubota D 722 injector pump repair
3
Kubota D 722 injector pump repair
The Injector pumpThe Injector pump Avant p/n 65136, Kubota p/n 16006-51010 Avant p/n 65136, Kubota p/n 16006-51010 isis
bolted to the engine with 4 pcsbolted to the engine with 4 pcs 5 5 mm allen screwsmm allen screws. .
When opening the srews the injector pump will pop upwards a little.When opening the srews the injector pump will pop upwards a little.
There is a shim plate between the engine body and the pump body. This must be There is a shim plate between the engine body and the pump body. This must be
placed back in its position when mounting.placed back in its position when mounting. If the shim is forgotten the engine If the shim is forgotten the engine
will not run properly.will not run properly.
Cover the opening in the engine body during injector pump repair Cover the opening in the engine body during injector pump repair
so that nothing falls into the engine.so that nothing falls into the engine.
4
Kubota D 722 injector pump repair
If there is cold slime in the engine,If there is cold slime in the engine, the slime must be removed mechanically.the slime must be removed mechanically.
The engine oil and oil filter needs to be changed when this repair is done.The engine oil and oil filter needs to be changed when this repair is done.
5
Kubota D 722 injector pump repair
In thius picture the ”cold slime” is visibleIn thius picture the ”cold slime” is visible
It is mixture of engine oil an humidity.It is mixture of engine oil an humidity.This can occur when the This can occur when the
ambient temperature is ambient temperature is
near 0 degrees celcius and near 0 degrees celcius and
the humidity is high and usage the humidity is high and usage
of the motor is very short of the motor is very short
period at a time.period at a time.
6
Kubota D 722 injector pump repair
7
Kubota D 722 injector pump repair
8
Kubota D 722 injector pump repair
Remove the retaining clip,Remove the retaining clip,
with small screw driverwith small screw driver
9
Kubota D 722 injector pump repair
Remove the retaining clip,Remove the retaining clip,
with small screw driverwith small screw driver
10
Kubota D 722 injector pump repair
Press in on the roller to remove the locking pinPress in on the roller to remove the locking pin
11
Kubota D 722 injector pump repair
Press in on the roller to remove the locking pinPress in on the roller to remove the locking pin
12
Kubota D 722 injector pump repair
Pull out the roller unitPull out the roller unit
13
Kubota D 722 injector pump repair
Remove the lock plate for the piston.Remove the lock plate for the piston.
14
Kubota D 722 injector pump repair
1. 1. Retainer clipRetainer clip
2. 2. Locking pinLocking pin
3. 3. Roller unitRoller unit
4. 4. Lock plate Lock plate
5. 5. PistonPiston
6. 6. SpringSpring
77. Upper spring cup. Upper spring cup
8. Adjustment piece8. Adjustment piece
9. 9. Control leverControl lever
15
Kubota D 722 injector pump repair
These parts are often corroded by the cold slime:These parts are often corroded by the cold slime:
Both parts must be cleaned from rust with Both parts must be cleaned from rust with
fine sandpaper or steel wool.fine sandpaper or steel wool.
16
Kubota D 722 injector pump repair
This is how the parts are inside the pump unit. If the parts are not rustfree the pump is not working properly
17
Kubota D 722 injector pump repair
In the piston there is a diagonal groove.In the piston there is a diagonal groove.
This groove is set to the opposite side This groove is set to the opposite side
from the control lever from the control lever
18
Kubota D 722 injector pump repair: ruiskutuspumpun korjaus
Spring : Kubota p/n 15841-51280In this picture there is rust that will cause the spring to break soon.
19
Kubota D 722 injector pump repair: ruiskutuspumpun korjaus
Spring : Kubota p/n 15841-51280If there is rust the springs need to be changed. It is a good idea to changeall 3 springs when doing this repair.
20
Kubota D 722 injector pump repair
First the adjustment piece is placedFirst the adjustment piece is placed
in the pump body so that the ball is in in the pump body so that the ball is in
the hole of the control lever. the hole of the control lever.
21
Kubota D 722 injector pump repair
With the control lever the movement of the With the control lever the movement of the
adjustment piece is tested.adjustment piece is tested.
22
Kubota D 722 injector pump repair
With the control lever the movement With the control lever the movement
of the adjustment piece is tested.of the adjustment piece is tested.
The adjustment piece will turn from The adjustment piece will turn from
side to side when moving the lever.side to side when moving the lever.
23
Kubota D 722 injector pump repair
The upper spring cup is next to The upper spring cup is next to
be placed in the pump. be placed in the pump.
24
Kubota D 722 injector pump repair
The spring is mounted.The spring is mounted.
25
Kubota D 722 injector pump repair
Pay attention when assembling the piston to the pump.Pay attention when assembling the piston to the pump.
The diagonal groove is on the opposite side of theThe diagonal groove is on the opposite side of the
control lever. Do not push all the way down.control lever. Do not push all the way down.
26
Kubota D 722 injector pump repair
Attention:Attention: The diagonal groove The diagonal groove
must be on the opposite side must be on the opposite side
from the control lever.from the control lever.
If the piston is placed wrong If the piston is placed wrong
way the, the engine will smoke way the, the engine will smoke
heavily and does not stop.heavily and does not stop.
27
Kubota D 722 injector pump repair
Attention: The diagonal groove Attention: The diagonal groove
must be on the opposite side must be on the opposite side
from the control lever.from the control lever.
28
Kubota D 722 injector pump repair
The lock plate is placed next.The lock plate is placed next.
29
Kubota D 722 injector pump repair
On the roller unit there is a spacer On the roller unit there is a spacer
that goes next.that goes next.
30
Kubota D 722 injector pump repair
The roller unit is placed so that the opening The roller unit is placed so that the opening
on the side is towards the locking pin hole.on the side is towards the locking pin hole.
31
Kubota D 722 injector pump repair
The roller unit is pushed agaisnt the spring.The roller unit is pushed agaisnt the spring.
Utill the locking pin fits. This should take very little force,Utill the locking pin fits. This should take very little force,
if the roller feels stuck, moving the control if the roller feels stuck, moving the control
lever a little will help.lever a little will help.
32
Kubota D 722 injector pump repair
The retainer clip is placed back toThe retainer clip is placed back to
its position.its position.
When the repair is complete the When the repair is complete the
control lever should move form control lever should move form
side to side when tilting the pump.side to side when tilting the pump.
The pump should be lubricated with The pump should be lubricated with
weapon oil or engine oil before weapon oil or engine oil before
being mounted back to the engine being mounted back to the engine