64033854-ACI-MANUAL-OF-CONCRETE-PRACTICE-INDEXâ€”2010

ACI MANUAL OFCONCRETE PRACTICE

INDEX—2010(with ACI CONCRETE TERMINOLOGY)

New editions of each part of the ACI Manual ofConcrete Practice are issued annually and includethe latest ACI standards and committee reports.

American Concrete Institute®

Advancing concrete knowledge

american concrete instituteP.O. Box 9094

Farmington Hills, MI 48333-9094

ACI Certification Programs

The final quality of a concrete structure depends on qualified people to construct it. ACI certification programs identify craftsmen, technicians,and inspectors who have demonstrated their qualifications. The following programs are administered by ACI to fulfill the growing demand in theindustry for certified workers. More information about these programs is available at www.acicertification.org.

AMERICAN CONCRETE INSTITUTEwww.concrete.org

The reports and standards herein are reprints of copyrighted material.

All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film,or other distribution and storage media, without the written consent of ACI.

The reports and standards herein were the latest approved version at the time this edition was published. The content of eachreport or standard is subject to periodic review and to revision whenever the developments in concrete design and constructionwarrant a change. Since this is a continuing process, some reports or standards in this volume may have been superseded in theinterim since publication. Inquiries concerning revisions or additional material in a subject area are welcome and should be directedto Institute headquarters.

ACI committee documents are intended for the use of individuals who are competent to evaluate the significance and limitations ofits content and recommendations and who will accept responsibility for the application of the material it contains. Individuals whouse this publication in any way assume all risk and accept total responsibility for the application and use of this information.

All information in this publication is provided “as is” without warranty of any kind, either expressed or implied, including but notlimited to, the implied warranties of merchantability, fitness for a particular purpose, or non-infringement.

ACI and its members disclaim liability for damages of any kind, including any special, indirect, incidental, or consequentialdamages, including, without limitation, lost revenues or lost profits, which may result from the use of this publication.

It is the responsibility of the user of this document to establish health and safety practices appropriate to the specific circumstancesinvolved with its use. ACI does not make any representations with regard to health and safety issues and the use of this document.The user must determine the applicability of all regulatory limitations before applying the document and must comply with all appli-cable laws and regulations, including but not limited to, United States Occupational Safety and Health Administration (OSHA) healthand safety standards.

Printed in the United States of AmericaISSN 0065-7875

Carl R. Bischof, Editor

ACI’s guides, reports, specifications, and codes are based upon the most current infor-mation and research available, and every effort is made to publish error-free documents.Occasionally, however, mistakes are uncovered after publication of a document. Whenthis happens, a list of corrections, called an errata, is issued. All errata for ACI’s technicalcommittee documents and SPs (symposium publications or special publications) are nowavailable on-line. Go to www.concrete.org, click on “Publications” on the top menu bar,then on “Errata.”

ii

Tilt-Up Supervisor & Technician

Shotcrete Nozzleman (Dry-Mix Process)

Shotcrete Nozzleman (Wet-Mix Process)

Concrete Flatwork Finisher & Technician

Specialty Commercial/Industrial Concrete Flatwork Finisher

Concrete Field Testing Technician—Grade I

Concrete Strength Testing Technician

Concrete Laboratory Testing Technician—Levels 1 & 2

Aggregate Base Testing Technician

Aggregate Testing Technician—Levels 1 & 2

Concrete Construction Special Inspector

Concrete Transportation Construction Inspector

CSA-Based Concrete Construction Special Inspector

CSA-Based Concrete Field Testing Technician—Grade I

This document may already contain reference to these ACI certification programs, which can be incorporated into project specifications orquality control procedures. If not, suggested guide specifications are available on request from the ACI Certification Department.

Enhancement of ACI Documents

ACI documents are subject to periodic review, and suggestions for their improvement are invited. All comments regarding ACI documentsshould be addressed to the Managing Director of Engineering at ACI.

iii

ACI MANUAL OF CONCRETE PRACTICE—2010The ACI Manual of Concrete Practice is a six-part compilation of current ACI standards and committee reports.

Part 1—ACI 117-06 to ACI 224.3R-95(08)Part 2—ACI 225-99(05) to ACI 315-99Part 3—ACI 318-08 to ACI 347.2R-05Part 4—ACI 349-06 to ACI 360R-06Part 5—ACI 362.1R-97(02) to ACI 503.7-07Part 6—ACI 506R-05 to ACI ITG-7-09

Some of the most important work of the Institute is performed by its technical committees that prepare thecommittee reports and standards contained in the Manual. Technical committees of the Institute are organized intothe following five groups with regard to their function: 100—General, 200—Materials and Properties of Concrete,300—Design and Construction, 400—Concrete Reinforcement and Structural Analysis, and 500—SpecializedApplications and Repair. Committees are assigned numbers that indicate their group or general area of responsibility.

Each standard of the Institute bears a hyphenated number to identify it. The first three digits identify the committeeoriginating the standard, and the last two digits identify the year it was adopted. Thus, standard ACI 305.1-06 wasprepared by Committee 305 and was adopted as a standard in the year 2006.

Committee reports are also identified by a hyphenated number with the addition of an “R” to indicate a reportrather than a standard. For committee reports, the last two digits refer to either the year of original publication or, ina few cases, to the year of adoption of a related standard.

The following list contains the numbers and titles of all committee reports and standards found in the 2010 ACI Manualof Concrete Practice. Reports and Standards are listed numerically and the location in the Manual follows the title.

100—General

117-06 Specifications for Tolerances for Concrete Construction and Materials and Commentary, Part 1

121R-08 Guide for Concrete Construction Quality Systems in Conformance with ISO 9001, Part 1

122R-02 Guide to Thermal Properties of Concrete and Masonry Systems, Part 1

126.3R-99 Reapproved 2008 Guide to Recommended Format for Concrete in Materials Property Database,Part 1

200—Materials and Properties of Concrete

201.1R-08 Guide for Conducting a Visual Inspection of Concrete in Service, Part 1

201.2R-08 Guide to Durable Concrete, Part 1

207.1R-05 Guide to Mass Concrete, Part 1

207.2R-07 Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, Part 1

207.3R-94 Reapproved 2008 Practices for Evaluation of Concrete in Existing Massive Structures for ServiceConditions, Part 1

207.4R-05 Cooling and Insulating Systems for Mass Concrete, Part 1

207.5R-99 Roller-Compacted Mass Concrete, Part 1

209R-92 Reapproved 2008 Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures,Part 1

209.1R-05 Report on Factors Affecting Shrinkage and Creep of Hardened Concrete, Part 1

209.2R-08 Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, Part 1

210R-93 Reapproved 2008 Erosion of Concrete in Hydraulic Structures, Part 1

211.1-91 Reapproved 2009 Standard Practice for Selecting Proportions for Normal, Heavyweight, andMass Concrete, Part 1

iv

211.2-98 Reapproved 2004 Standard Practice for Selecting Proportions for Structural Lightweight Concrete,Part 1

211.3R-02 Reapproved 2009 Guide for Selecting Proportions for No-Slump Concrete, Part 1

211.4R-08 Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and OtherCementitious Materials, Part 1

211.5R-01 Reapproved 2009 Guide for Submittal of Concrete Proportions, Part 1

212.3R-04 Chemical Admixtures for Concrete, Part 1

212.4R-04 Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, Part 1

213R-03 Guide for Structural Lightweight-Aggregate Concrete, Part 1

214R-02 Evaluation of Strength Test Results of Concrete, Part 1

214.4R-03 Guide for Obtaining Cores and Interpreting Compressive Strength Results, Part 1

216.1-07 Code Requirements for Determining Fire Resistance of Concrete and Masonry ConstructionAssemblies, Part 1

221R-96 Reapproved 2001 Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete,Part 1

221.1R-98 Reapproved 2008 Report on Alkali-Aggregate Reactivity, Part 1

222R-01 Protection of Metals in Concrete Against Corrosion, Part 1

222.2R-01 Corrosion of Prestressing Steels, Part 1

222.3R-03 Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures,Part 1

223-98 Standard Practice for the Use of Shrinkage-Compensating Concrete, Part 1

224R-01 Reapproved 2008 Control of Cracking in Concrete Structures, Part 1

224.1R-07 Causes, Evaluation, and Repair of Cracks in Concrete Structures, Part 1

224.2R-92 Reapproved 2004 Cracking of Concrete Members in Direct Tension, Part 1

224.3R-95 Reapproved 2008 Joints in Concrete Construction, Part 1

225R-99 Reapproved 2005 Guide to the Selection and Use of Hydraulic Cements, Part 2

228.1R-03 In-Place Methods to Estimate Concrete Strength, Part 2

228.2R-98 Reapproved 2004 Nondestructive Test Methods for Evaluation of Concrete in Structures, Part 2

229R-99 Reapproved 2005 Controlled Low-Strength Materials, Part 2

230.1R-09 Report on Soil Cement, Part 2

232.1R-00 Reapproved 2006 Use of Raw or Processed Natural Pozzolans in Concrete, Part 2

232.2R-03 Use of Fly Ash in Concrete, Part 2

233R-03 Slag Cement in Concrete and Mortar, Part 2

234R-06 Guide for the Use of Silica Fume in Concrete, Part 2

237R-07 Self-Consolidating Concrete, Part 2

238.1R-08 Report on Measurements of Workability and Rheology of Fresh Concrete, Part 2

300—Design and Construction

301-05 Specifications for Structural Concrete, Part 2

SP-15(05) Field Reference Manual (Synopsis only), Part 2

302.1R-04 Guide for Concrete Floor and Slab Construction, Part 2

302.2R-06 Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, Part 2

303R-04 Guide to Cast-in-Place Architectural Concrete Practice, Part 2

303.1-97 Standard Specification for Cast-In-Place Architectural Concrete, Part 2

304R-00 Guide for Measuring, Mixing, Transporting, and Placing Concrete, Part 2

304.1R-92 Reapproved 2005 Guide for the Use of Preplaced Aggregate Concrete for Structural and MassConcrete Applications, Part 2

v

304.2R-96 Reapproved 2008 Placing Concrete by Pumping Methods, Part 2

304.3R-96 Reapproved 2004 Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Part 2

304.4R-95 Reapproved 2008 Placing Concrete with Belt Conveyors, Part 2

304.6R-09 Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Part 2

305R-99 Hot Weather Concreting, Part 2

305.1-06 Specification for Hot Weather Concreting, Part 2

306R-88 Reapproved 2002 Cold Weather Concreting, Part 2

306.1-90 Reapproved 2002 Standard Specification for Cold Weather Concreting, Part 2

307-08 Code Requirements for Reinforced Concrete Chimneys (ACI 307-08) and Commentary, Part 2

308R-01 Reapproved 2008 Guide to Curing Concrete, Part 2

308.1-98 Standard Specification for Curing Concrete, Part 2

309R-05 Guide for Consolidation of Concrete, Part 2

309.1R-08 Report on Behavior of Fresh Concrete During Vibration, Part 2

309.2R-98 Reapproved 2005 Identification and Control of Visible Effects of Consolidation on FormedConcrete Surfaces, Part 2

309.5R-00 Reapproved 2006 Compaction of Roller-Compacted Concrete, Part 2

311.1R-07 ACI Manual of Concrete Inspection—SP-2(07) (Synopsis only), Part 2

311.4R-05 Guide for Concrete Inspection, Part 2

311.5-04 Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete, Part 2

311.6-09 Specification for Ready Mixed Concrete Testing Services, Part 2

313-97 Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for StoringGranular Materials, Part 2

313R-97 Commentary on Standard Practice for Design and Construction of Concrete Silos and StackingTubes for Storing Granular Materials, Part 2

315-99 Details and Detailing of Concrete Reinforcement, Part 2

SP-66(04) ACI Detailing Manual (Synopsis only), Part 2

318-08 Building Code Requirements for Structural Concrete (ACI 318-08) and Commentary, Part 3

SP-71(08) ASTM Standards in ACI 318 (Synopsis only), Part 3

325.10R-95 Reapproved 2001 Report on Roller-Compacted Concrete Pavements, Part 3

325.11R-01 Accelerated Techniques for Concrete Paving, Part 3

325.12R-02 Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Part 3

325.13R-06 Concrete Overlays for Pavement Rehabilitation, Part 3

330R-08 Guide for the Design and Construction of Concrete Parking Lots, Part 3

330.1-03 Specification for Unreinforced Concrete Parking Lots, Part 3

332-08 Code Requirements for Residential Concrete and Commentary, Part 3

332.1R-06 Guide to Residential Concrete Construction, Part 3

334.1R-92 Reapproved 2002 Concrete Shell Structures—Practice and Commentary, Part 3

334.3R-05 Construction of Concrete Shells Using Inflated Forms, Part 3

336.1-01 Specification for the Construction of Drilled Piers, Part 3

336.2R-88 Reapproved 2002 Suggested Analysis and Design Procedures for Combined Footings and Mats,Part 3

336.3R-93 Reapproved 2006 Design and Construction of Drilled Piers, Part 3

341.2R-97 Reapproved 2003 Seismic Analysis and Design of Concrete Bridge Systems, Part 3

341.3R-07 Seismic Evaluation and Retrofit Techniques for Concrete Bridges, Part 3

343R-95 Reapproved 2004 Analysis and Design of Reinforced Concrete Bridge Structures, Part 3

345R-91 Reapproved 2005 Guide for Concrete Highway Bridge Deck Construction, Part 3

345.1R-06 Guide for Maintenance of Concrete Bridge Members, Part 3

345.2R-98 Reapproved 2005 Guide for Widening Highway Bridges, Part 3

vi

346-09 Specification for Cast-in-Place Concrete Pipe, Part 3

347-04 Guide to Formwork for Concrete, Part 3

347.2R-05 Guide for Shoring/Reshoring of Concrete Multistory Buildings, Part 3

SP-4 Formwork for Concrete (Synopsis only), Part 3

349-06 Code Requirements for Nuclear Safety-Related Concrete Structures (ACI 349-06) andCommentary, Part 4

349.1R-07 Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures, Part 4

349.2R-07 Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples, Part 4

349.3R-02 Evaluation of Existing Nuclear Safety-Related Concrete Structures, Part 4

350-06 Code Requirements for Environmental Engineering Concrete Structures (ACI 350-06) andCommentary, Part 4

350.1-01/350.1R-01 Tightness Testing of Environmental Engineering Concrete Structures (ACI 350.1-01) and

Commentary (ACI 350.1R-01), Part 4

350.2R-04 Concrete Structures for Containment of Hazardous Materials, Part 4

350.3-06 Seismic Design of Liquid-Containing Concrete Structures (ACI 350.3-06) and Commentary, Part 4

350.4R-04 Design Considerations for Environmental Engineering Concrete Structures, Part 4

351.1R-99 Reapproved 2008 Grouting between Foundations and Bases for Support of Equipment andMachinery, Part 4

351.2R-94 Reapproved 1999 Foundations for Static Equipment, Part 4

351.3R-04 Foundations for Dynamic Equipment, Part 4

352R-02 Recommendations for Design of Beam-Column Connections in Monolithic Reinforced ConcreteStructures, Part 4

352.1R-89 Reapproved 2004 Recommendations for Design of Slab-Column Connections in MonolithicReinforced Concrete Structures, Part 4

355.2-07 Qualification of Post-Installed Mechanical Anchors in Concrete (ACI 355.2-07) and Commentary,Part 4

357R-84 Reapproved 1997 Guide for the Design and Construction of Fixed Offshore Concrete Structures,Part 4

357.2R-88 Reapproved 1997 Report on Barge-Like Concrete Structures (Abstract only), Part 4

358.1R-92 Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, Part 4

359-07 Code for Concrete Containments (Synopsis only), Part 4

360R-06 Design of Slabs-on-Ground, Part 4

362.1R-97 Reapproved 2002 Guide for the Design of Durable Parking Structures, Part 5

362.2R-00 Reapproved 2005 Guide for Structural Maintenance of Parking Structures, Part 5

363R-92 Reapproved 1997 Report on High-Strength Concrete, Part 5

363.2R-98 Guide to Quality Control and Testing of High-Strength Concrete, Part 5

364.1R-07 Guide for Evaluation of Concrete Structures before Rehabilitation, Part 5

364.2T-08 Increasing Shear Capacity within Existing Reinforced Concrete Structures, Part 5

364.3R-09 Guide for Cementitious Repair Material Data Sheet, Part 5

365.1R-00 Service-Life Prediction, Part 5

371R-08 Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Part 5

372R-03 Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures,Part 5

373R-97 Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons,Part 5

374.1-05 Acceptance Criteria for Moment Frames Based on Structural Testing and Commentary, Part 5

vii

400—Concrete Reinforcement and Structural Analysis

408R-03 Bond and Development of Straight Reinforcing Bars in Tension, Part 5

408.2R-92 Reapproved 2005 Bond under Cyclic Loads (Abstract only), Part 5

408.3R-09 Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars inTension and Commentary, Part 5

421.1R-08 Guide to Shear Reinforcement for Slabs, Part 5

421.2R-07 Seismic Design of Punching Shear Reinforcement in Flat Plates, Part 5

423.3R-05 Recommendations for Concrete Members Prestressed with Unbonded Tendons, Part 5

423.4R-98 Corrosion and Repair of Unbonded Single Strand Tendons, Part 5

423.6-01/423.6R-01 Specification for Unbonded Single-Strand Tendons (ACI 423.6-01) and Commentary, Part 5

423.7-07 Specification for Unbonded Single-Strand Tendon Materials (ACI 423.7-07) and Commentary, Part 5

435R-95 Reapproved 2000 Control of Deflection in Concrete Structures, Part 5

435.8R-85 Reapproved 1997 Observed Deflections of Reinforced Concrete Slab Systems, and Causes ofLarge Deflections (Synopsis only), Part 5

437R-03 Strength Evaluation of Existing Concrete Buildings, Part 5

437.1R-07 Load Tests of Concrete Structures: Methods, Magnitude, Protocols, and Acceptance Criteria, Part 5

439.3R-07 Types of Mechanical Splices for Reinforcing Bars, Part 5

439.4R-09 Report on Steel Reinforcement—Material Properties and U.S. Availability, Part 5

440R-07 Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Part 5

440.1R-06 Guide for the Design and Construction of Structural Concrete Reinforced with FRP Bars, Part 5

440.2R-08 Guide for the Design and Construction of Externally Bonded FRP Systems for StrengtheningConcrete Structures, Part 5

440.3R-04 Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or StrengtheningConcrete Structures, Part 5

440.4R-04 Prestressing Concrete Structures with FRP Tendons, Part 5

440.5-08 Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, Part 5

440.6-08 Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for ConcreteReinforcement, Part 5

441R-96 High-Strength Concrete Columns, Part 5

445R-99 Reapproved 2009 Recent Approaches to Shear Design of Structural Concrete, Part 5

446.1R-91 Reapproved 1999 Fracture Mechanics of Concrete: Concepts, Models and Determination ofMaterial Properties (Abstract only), Part 5

446.3R-97 Finite Element Analysis of Fracture in Concrete Structures, Part 5

446.4R-04 Report on Dynamic Fracture of Concrete, Part 5

500—Specialized Applications and Repair

503R-93 Reapproved 2008 Use of Epoxy Compounds with Concrete, Part 5

503.1-92 Reapproved 2003 Standard Specification for Bonding Hardened Concrete, Steel, Wood, Brick,and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, Part 5

503.2-92 Reapproved 2003 Standard Specification for Bonding Plastic Concrete to Hardened Concretewith a Multi-Component Epoxy Adhesive, Part 5

503.3-92 Reapproved 2003 Standard Specification for Producing a Skid-Resistant Surface on Concrete bythe Use of a Multi-Component Epoxy System, Part 5

503.4-92 Reapproved 2003 Standard Specification for Repairing Concrete with Epoxy Mortars, Part 5

503.5R-92 Reapproved 2003 Guide for the Selection of Polymer Adhesives with Concrete, Part 5

viii

503.6R-97 Reapproved 2003 Guide for the Application of Epoxy and Latex Adhesives for Bonding FreshlyMixed and Hardened Concretes, Part 5

503.7-07 Specification for Crack Repair by Epoxy Injection, Part 5

506R-05 Guide to Shotcrete, Part 6

506.1R-08 Guide to Fiber-Reinforced Shotcrete, Part 6

506.2-95 Specification for Shotcrete, Part 6

506.4R-94 Reapproved 2004 Guide for the Evaluation of Shotcrete, Part 6

506.5R-09 Guide for Specifying Underground Shotcrete, Part 6

522R-06 Pervious Concrete, Part 6

522.1-08 Specification for Pervious Concrete Pavement, Part 6

523.1R-06 Guide for Cast-in-Place Low-Density Cellular Concrete, Part 6

523.2R-96 Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, Part 6

523.4R-09 Guide for Design and Construction of Autoclaved Aerated Concrete Panels, Part 6

524R-08 Guide to Portland Cement-Based Plaster, Part 6

530-08/TMS 402-08/ASCE 5-08

Building Code Requirements for Masonry Structures, Part 6

530.1-08/TMS 602-08/ASCE 6-08

Specification for Masonry Structures, Part 6

530R-08/TMS 402-08/ASCE 5-08

Commentary on Building Code Requirements for Masonry Structures, Part 6

530.1R-08/TMS 602-08/ASCE 6-08

Commentary on Specification for Masonry Structures, Part 6

533R-93 Reappoved 2004 Guide for Precast Concrete Wall Panels, Part 6

533.1R-02 Design Responsibility for Architectural Precast-Concrete Projects, Part 6

543R-00 Reapproved 2005 Design, Manufacture, and Installation of Concrete Piles, Part 6

544.1R-96 Reapproved 2002 Report on Fiber Reinforced Concrete, Part 6

544.2R-89 Reapproved 1999 Measurement of Properties of Fiber Reinforced Concrete, Part 6

544.3R-08 Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, Part 6

544.4R-88 Reapproved 1999 Design Considerations for Steel Fiber Reinforced Concrete, Part 6

546R-04 Concrete Repair Guide, Part 6

546.2R-98 Guide to Underwater Repair of Concrete, Part 6

546.3R-06 Guide for the Selection of Materials for the Repair of Concrete, Part 6

548.1R-09 Guide for the Use of Polymers in Concrete, Part 6

548.3R-09 Report on Polymer-Modified Concrete, Part 6

548.4-93 Reapproved 1998 Standard Specification for Latex-Modified Concrete (LMC) Overlays, Part 6

548.5R-94 Reapproved 1998 Guide for Polymer Concrete Overlays, Part 6

548.7-04 Test Method for Load Capacity of Polymer Concrete Underground Utility Structures, Part 6

548.8-07 Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking GarageDecks, Part 6

548.9-08 Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks,Part 6

549R-97 Reapproved 2009 Report on Ferrocement, Part 6

549.1R-93 Reapproved 2009 Guide for the Design, Construction, and Repair of Ferrocement, Part 6

549.2R-04 Report on Thin Reinforced Cementitious Products, Part 6

550.1R-09 Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures,Part 6

ix

551.1R-05 Tilt-Up Concrete Construction Guide, Part 6

555R-01 Removal and Reuse of Hardened Concrete, Part 6

T1.2-03/T1.2R-03 Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned

Concrete Members and Commentary, Part 6

ITG-3-04 Report on Bridge Decks Free of Steel Reinforcement, Part 6

ITG-4.1-07 Specification for High-Strength Concrete in Moderate to High Seismic Applications, Part 6

ITG-4.2R-06 Materials and Quality Considerations for High-Strength Concrete in Moderate to High SeismicApplications, Part 6

ITG-4.3R-07 Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High SeismicApplications, Part 6

ITG-5.1-07 Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based onValidation Testing and Commentary, Part 6

ITG-5.2-09 Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall SatisfyingACI ITG-5.1 (ACI ITG-5.2-09) and Commentary, Part 6

ITG-7-09 Specification for Tolerances for Precast Concrete, Part 6

SP-17(09) ACI Design Handbook (Synopsis only), Part 6

xi

THE AMERICAN CONCRETE INSTITUTE

is a nonprofit, nonpartisan organization of engineers, architects, scientists,constructors, and individuals associated in their technical interest with the field ofconcrete and dedicated to public service. The purpose of the Institute is to furtherengineering and technical education, scientific investigation and research, anddevelopment of standards for the design and construction of concrete structures.Members of the Institute are involved in gathering, correlating, and disseminatinginformation for the improvement of the design, construction, manufacture, use,and maintenance of concrete products and structures. The Institute and itsmembers also promote improved technology, technical competence, and gooddesign and construction practices.

Since 1904, the objectives of the Institute have been achieved by a combinedmembership effort. Individually and through committees, and with thecooperation of many public and private agencies, members have correlated theresults of research, from both field and laboratory, and of practices in design,construction, and manufacture.

The work of the Institute is available to the concrete industry through seminars,workshops, chapter functions, and publications. The Institute publishes threeperiodicals, the ACI Structural Journal, ACI Materials Journal, and ConcreteInternational. The Institute also has an extensive nonperiodical publicationsprogram, which includes committee reports, building code requirements and otherstandards, symposia, manuals, design handbooks, monographs, education bulletins,certification program workbooks, and the ACI Manual of Concrete Practice.

Some of the most recent publications are:

CP-60(09) Shotcrete Nozzleman Craftsman Workbook

CP-21 Concrete Construction Special Inspector Reference Package

CP-31 Concrete Transportation Construction Inspector ReferencePackage

CP-33 Associate Concrete Transportation Construction InspectorReference Package

SP-261 Tenth ACI International Conference on Recent Advances inConcrete Technology and Sustainability Issues

SP-262 Ninth ACI International Conference on Superplasticizers and Other Chemical Admixtures

SP-263 Slag Cement Concrete

SP-264 Serviceability of Concrete Members Reinforced with Internal/External Reinforcement

SP-265 Thomas T.C. Hsu Symposium: Shear and Torsion in ConcreteStructures

INDEX

MCP INDEX IND-1

The subject index contains all documents included in the sixparts of the 2010 ACI Manual of Concrete Practice. Followingeach topic is a list of documents. Entire documents that relate tothe topic are listed first, followed by documents that contain achapter (or chapters) that relate to the topic, which are followed bydocuments that have a section (or sections) that relate to the topic.Refer to the numerical listing in the front of each Manual ofConcrete Practice to see which part the document is in.

Abrasion, see also Erosion210R—Erosion of Concrete in Hydraulic Structures

201.2R—Guide to Durable Concrete, Ch. 8

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.20503R—Use of Epoxy Compounds with Concrete, 3.5544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.8

Abrasion resistance, see also Wear resistance213R—Guide for Structural Lightweight-Aggregate Concrete, 4.20223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 2.5.7523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 5.5, 5.6

Absorption211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, 2.1213R—Guide for Structural Lightweight-Aggregate Concrete, 4.15506.5R—Guide for Specifying Underground Shotcrete, 8.5

Abutments341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges, 4.7343R—Analysis and Design of Reinforced Concrete Bridge Structures, 11.5

Accelerated curing, see also Curing325.11R—Accelerated Techniques for Concrete Paving

308R—Guide to Curing Concrete, 2.8318—Building Code Requirements for Structural Concrete, 5.11.3

Accelerating admixtures, see also Admixtures212.3R—Chemical Admixtures for Concrete, Ch. 3306R—Cold Weather Concreting, Ch. 9506.5R—Guide for Specifying Underground Shotcrete, 4.1

Acceptance, see also Testing or Evaluation349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures

350.1—Tightness Testing of Environmental Engineering Concrete Structures355.2—Qualification of Post-Installed Mechanical Anchors in Concrete374.1—Acceptance Criteria for Moment Frames Based on Structural Testing437.1R—Load Tests of Concrete Structures: Methods, Magnitude, Protocols, and Acceptance CriteriaITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation TestingITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 7

214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, 3.1221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 5.4228.1R—In-Place Methods to Estimate Concrete Strength, 7.2301—Specifications for Structural Concrete, 1.7318—Building Code Requirements for Structural Concrete, 5.6, 20.5336.3R—Design and Construction of Drilled Piers, 5.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.6, 20.6350—Code Requirements for Environmental Engineering Concrete Structures, 5.5, 20.5373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 5.2506.2—Specification for Shotcrete, 1.9506.5R—Guide for Specifying Underground Shotcrete, Ch. 11

Acid attack, see Chemical attack

Acrylic latex, see also Polymer concrete548.3R—Report on Polymer-Modified Concrete, Ch. 4, 3.2.4, 4.2

Adhesives, see also Epoxy or Polymer adhesives503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System503.4—Standard Specification for Repairing Concrete with Epoxy Mortars503.5R—Guide for the Selection of Polymer Adhesives with Concrete

IND-2 MANUAL OF CONCRETE PRACTICE

503.6R—Guide for the Application of Epoxy and Latex Adhesives for Bonding Freshly Mixed and Hardened Concretes, Ch. 5, Ch. 6

372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.8440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 4.7440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.1503R—Use of Epoxy Compounds with Concrete, 3.2, 4.6

Adits207.5R—Roller-Compacted Mass Concrete, 4.6

Admixtures212.3R—Chemical Admixtures for Concrete212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete234R—Guide for the Use of Silica Fume in Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and PlacingSP-15—Field Reference Manual

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 7211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, Ch. 4225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 4306R—Cold Weather Concreting, Ch. 9325.11R—Accelerated Techniques for Concrete Paving, Ch. 4371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 4, App. 4

207.1R—Guide to Mass Concrete, 2.4223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 2.4229R—Controlled Low-Strength Materials, 3.4230.1R—Report on Soil Cement, 4.6233R—Slag Cement in Concrete and Mortar, 3.3238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.5301—Specifications for Structural Concrete, 4.1302.1R—Guide for Concrete Floor and Slab Construction, 5.7304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.5304.2R—Placing Concrete by Pumping Methods, 4.6305R—Hot Weather Concreting, 2.7313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 2.5318—Building Code Requirements for Structural Concrete, 3.6325.10R—Report on Roller-Compacted Concrete Pavements, 3.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.6350—Code Requirements for Environmental Engineering Concrete Structures, 3.6357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.9363R—Report on High-Strength Concrete, 2.3, 3.7

372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.3373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.3506R—Guide to Shotcrete, 2.7506.2—Specification for Shotcrete, 2.5523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 2.5524R—Guide to Portland Cement-Based Plaster, 4.6533R—Guide for Precast Concrete Wall Panels, 4.5544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 3.3546.2R—Guide to Underwater Repair of Concrete, 6.9549R—Report on Ferrocement, 3.4ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, 6.7, 6.8

Aeration210R—Erosion of Concrete in Hydraulic Structures, 5.3

Aesthetics237R—Self-Consolidating Concrete, 3.4

Aggregates201.2R—Guide to Durable Concrete207.4R—Cooling and Insulating Systems for Mass Concrete211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete213R—Guide for Structural Lightweight-Aggregate Concrete221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete301—Specifications for Structural Concrete304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete SurfacesSP-15—Field Reference Manual

122R—Guide to Thermal Properties of Concrete and Masonry Systems, Ch. 2126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 6304.2R—Placing Concrete by Pumping Methods, Ch. 4306R—Cold Weather Concreting, Ch. 3364.3R—Guide for Cementitious Repair Material Data Sheet, 3.5

533R—Guide for Precast Concrete Wall Panels, Ch. 4

207.1R—Guide to Mass Concrete, 2.5207.5R—Roller-Compacted Mass Concrete, 5.2211.3R—Guide for Selecting Proportions for No-Slump Concrete, 3.5211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, 4.8, 4.9211.5R—Guide for Submittal of Concrete Proportions, 2.2

MCP INDEX IND-3

223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 2.2224R—Control of Cracking in Concrete Structures, 5.4229R—Controlled Low-Strength Materials, 3.7238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.4302.1R—Guide for Concrete Floor and Slab Construction, 5.4304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 6.2.4, 7.4305R—Hot Weather Concreting, 2.8318—Building Code Requirements for Structural Concrete, 3.3325.10R—Report on Roller-Compacted Concrete Pavements, 3.2325.11R—Accelerated Techniques for Concrete Paving, 4.7349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.3350—Code Requirements for Environmental Engineering Concrete Structures, 3.3363R—Report on High-Strength Concrete, 2.5506R—Guide to Shotcrete, 2.4506.2—Specification for Shotcrete, 2.2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 2.4523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 2.1524R—Guide to Portland Cement-Based Plaster, 4.4548.5R—Guide for Polymer Concrete Overlays, 3.2548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks, 2.2, 3.6548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks, 2.2, 3.6555R—Removal and Reuse of Hardended Concrete, 5.2, 5.3ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, 6.5

Aggressive chemical exposure, see Chemical attack

Aging, see also Creep209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures

Air content311.6—Specification for Ready Mixed Concrete Testing Services

212.3R—Chemical Admixtures for Concrete, 2.9309R—Guide for Consolidation of Concrete, 17.3506.5R—Guide for Specifying Underground Shotcrete, 8.3

Air entrainment, see also Admixtures212.3R—Chemical Admixtures for Concrete, Ch. 2

211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, 4.2211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, 2.4212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.5221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.7225R—Guide to the Selection and Use of Hydraulic Cements, 4.1234R—Guide for the Use of Silica Fume in Concrete, 4.8

ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, 6.4

Air voids, see also Voids309R—Guide for Consolidation of Concrete, 7.7.2309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 3.2

Alignment, see Tolerances

Alkali440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.6

Alkali-aggregate reactivity (AAR), see also Aggregates, Durability

221.1R—Report on Alkali-Aggregate Reactivity

212.3R—Chemical Admixtures for Concrete, 6.10213R—Guide for Structural Lightweight-Aggregate Concrete, 4.16

Alkali-silica reactivity (ASR), see also Durability221.1R—Report on Alkali-Aggregate Reactivity232.1R—Use of Raw or Processed Natural Pozzolans in Concrete


233R—Slag Cement in Concrete and Mortar, 5.10234R—Guide for the Use of Silica Fume in Concrete, 5.3

Allowable stress design530—Building Code Requirements for Masonry Structures, Ch. 2

334.1R—Concrete Shell Structures Practice, 4.1

Alternate design method318—Building Code Requirements for Structural Concrete, App. B350—Code Requirements for Environmental Engineering Concrete Structures, App. I

Alternate strength and load factors318—Building Code Requirements for Structural Concrete, App. C350—Code Requirements for Environmental Engineering Concrete Structures, App. C

Analysis, see Design factors

Anchor ties in masonry301—Specifications for Structural Concrete, 2.2530—Building Code Requirements for Masonry Structures, 5.8530.1—Specification for Masonry Structures, 2.4

Anchorage, post-tensioning devices222.2R—Corrosion of Prestressing Steels


506.5R—Guide for Specifying Underground Shotcrete, Ch. 5

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 18.13350—Code Requirements for Environmental Engineering Concrete Structures, 18.13, 18.21357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.16423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.4, 2.6530—Building Code Requirements for Masonry Structures, 4.8543R—Design, Manufacture, and Installation of Concrete Piles, 3.6

Anchorage of reinforcement, see also Bond, Development length or Reinforcement – steel

408.2R—Bond under Cyclic Loads408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

318—Building Code Requirements for Structural Concrete, Ch. 12

350—Code Requirements for Environmental Engineering Concrete Structures, 12.6352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 5.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.16, 2.17423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.10, 4.3523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.9523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.2.1, 7.2.2, 7.2.3530—Building Code Requirements for Masonry Structures, 2.1.4T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 6.6

Anchorage to concrete349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples355.2—Qualification of Post-Installed Mechanical Anchors in Concrete

318—Building Code Requirements for Structural Concrete, Ch. 18, App. D, 12.6349—Code Requirements for Nuclear Safety-Related Concrete Structures, App. D440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 2

336.1—Specification for the Construction of Drilled Piers, 3.8350—Code Requirements for Environmental Engineering Concrete Structures, 12.6351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 6.2351.2R—Foundations for Static Equipment, 4.2351.3R—Foundations for Dynamic Equipment, 4.4423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.4, 2.6

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.10506R—Guide to Shotcrete, 5.5533R—Guide for Precast Concrete Wall Panels, 4.8546R—Concrete Repair Guide, 2.5546.2R—Guide to Underwater Repair of Concrete, 4.4

Anchors, see Anchorage to concrete

Aramid fibers, see also Fiber-reinforced polymer (FRP)

440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures

544.1R—Report on Fiber-Reinforced Concrete, 4.2.2

Architectural concrete303R—Guide to Cast-in-Place Architectural Concrete Practice303.1—Standard Specification for Cast-in-Place Architectural Concrete533.1R—Design Responsibility for Architectural Precast- Concrete ProjectsSP-15—Field Reference Manual

301—Specifications for Structural Concrete, Sec. 6

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.4533R—Guide for Precast Concrete Wall Panels, 5.3.4.5551.1R—Tilt-Up Concrete Construction Guide, 5.2

Ash, see also Fly ash229R—Controlled Low-Strength Materials, 3.3, 3.9

Autoclaved aerated concrete (AAC)523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels530—Building Code Requirements for Masonry Structures, App. A

Axially loaded members, see also Columns318—Building Code Requirements for Structural Concrete, Ch. 10349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 10, 18.11350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 10, 18.11441R—High-Strength Concrete Columns, Ch. 2, Ch. 3

363R—Report on High-Strength Concrete, 6.2

Backfill, see also Fills229R—Controlled Low-Strength Materials, Ch. 2

346—Specification for Cast-in-Place Concrete Pipe, 3.1.1.4, 3.2

MCP INDEX IND-5

Bacterial erosion, see also Chemical attack350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 4

210R—Erosion of Concrete in Hydraulic Structures, 7.2, 7.3

Bar deformations, see also Reinforcement – steel408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

Bars440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars

ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, 7.1, 7.2

Barges, see also Offshore structures357.2R—Report on Barge-Like Concrete Structures

Barrier systems, see Protective coatings

Base, see also Pavements229R—Controlled Low-Strength Materials, 2.5325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.1

Base of equipment and machinery351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery

Base of structure, see Foundations

Batching, see also Mixture proportioning304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 3, 12.2325.10R—Report on Roller-Compacted Concrete Pavements, Ch. 4, 7.3363R—Report on High-Strength Concrete, Ch. 4544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, Ch. 6

117—Specifications for Tolerances for Concrete Construction and Materials, 2.4126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 11.5207.1R—Guide to Mass Concrete, 4.1212.3R—Chemical Admixtures for Concrete, 1.7, 2.7, 3.8, 4.5221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 7.6232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 4.2233R—Slag Cement in Concrete and Mortar, 2.3302.1R—Guide for Concrete Floor and Slab Construction, 7.1304.4R—Placing Concrete with Belt Conveyors, 2.4, 2.6

305R—Hot Weather Concreting, 3.3325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2330.1—Specification for Unreinforced Concrete Parking Lots, 3.5506R—Guide to Shotcrete, 7.2506.1R—Guide to Fiber-Reinforced Shotcrete, 5.2506.2—Specification for Shotcrete, 3.2506.5R—Guide for Specifying Underground Shotcrete, Ch. 12522.1—Specification for Pervious Concrete Pavement, 3.4523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.2524R—Guide to Portland Cement-Based Plaster, 10.3ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, 8.1

Beam-column frame374.1—Acceptance Criteria for Moment Frames Based on Structural TestingT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, Ch. 6

Beam-column joints, see also Column-slab connections, Joints

352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures

Beams209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 3, 4.3 through 4.5, 4.8352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures445R—Recent Approaches to Shear Design of Structural Concrete544.4R—Design Considerations for Steel Fiber-Reinforced Concrete

350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 10, 14.7435R—Control of Deflection in Concrete Structures, Ch. 3, A4.2ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 5T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, Ch. 6, 4.6

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, Ch. 2224R—Control of Cracking in Concrete Structures, 4.7315—Details and Detailing of Concrete Reinforcement, 2.5, 5.3318—Building Code Requirements for Structural Concrete, Ch. 10.6343R—Analysis and Design of Reinforced Concrete Bridge Structures, 10.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 10.6, 14.7352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 4.2, 4.3363R—Report on High-Strength Concrete, 6.3


423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.2530—Building Code Requirements for Masonry Structures, 1.10

Bearings318—Building Code Requirements for Structural Concrete, 10.14341.2R—Seismic Analysis and Design of Concrete Bridge Systems, 4.4343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.20, 11.2350—Code Requirements for Environmental Engineering Concrete Structures, 16.6372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.6, 4.9373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.7, 4.9

Belt conveyor, see also placing concrete304.4R—Placing Concrete with Belt Conveyors, 2.5

Bending moment, see also Ultimate strength441R—High-Strength Concrete Columns, Ch. 3

Bending of reinforcing steel, see also Fabrication

315—Details and Detailing of Concrete Reinforcement530.1—Specification for Masonry Structures

301—Specifications for Structural Concrete, Sec. 3

307—Code Requirements for Reinforced Concrete Chimneys, 5.7318—Building Code Requirements for Structural Concrete, 7.3343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.7, 9.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 7.3350—Code Requirements for Environmental Engineering Concrete Structures, 7.2, 7.3439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities530—Building Code Requirements for Masonry Structures, 2.3

Bibliography363R—Report on High-Strength Concrete, 10.3

Binder548.5R—Guide for Polymer Concrete Overlays, Ch. 2

503R—Use of Epoxy Compounds with Concrete, 4.7

Bins, see also Silos313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 1.2, R4.3.2

Blast-furnace slag, see Ground granulated blast-furnace slag

Bleeding (concrete), see also Finishing308R—Guide to Curing Concrete

201.2R—Guide to Durable Concrete, 3.5212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.7214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, 2.1221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.5233R—Slag Cement in Concrete and Mortar, 4.3234R—Guide for the Use of Silica Fume in Concrete, 4.6351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 4.2.5

Blemishes, see Surface defects

Blended cements, see also Pozzolans225R—Guide to the Selection and Use of Hydraulic Cements, 2.1234R—Guide for the Use of Silica Fume in Concrete, 1.5

Blisters, see Surface defects

Bolts, see Anchorage

Bond, to concrete or substrates503R—Use of Epoxy Compounds with Concrete503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive503.5R—Guide for the Selection of Polymer Adhesives with Concrete503.6R—Guide for the Application of Epoxy and Latex Adhesives for Bonding Freshly Mixed and Hardened Concrete

440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 6506.4R—Guide for the Evaluation of Shotcrete, Ch. 3

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 13.1, 13.3440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.3446.4R—Report on Dynamic Fracture of Concrete, 2.4555R—Removal and Reuse of Hardened Concrete, 4.7

Bond of reinforcement to concrete, see also Anchorage of reinforcement

408R—Bond and Development of Straight Reinforcing Bars in Tension408.2R—Bond under Cyclic Loads408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

MCP INDEX IND-7

440.3R—Guide to Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.3213R—Guide for Structural Lightweight-Aggregate Concrete, 4.12304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 1.5325.10R—Report on Roller-Compacted Concrete Pavements, 5.7523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.2530—Building Code Requirements for Masonry Structures, 5.7546R—Concrete Repair Guide, 2.7

Bonded tendon222.2R—Corrosion of Prestressing Steels, 7.5313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 6.5318—Building Code Requirements for Structural Concrete, 18.9, 18.18350—Code Requirements for Environmental Engineering Concrete Structures, 18.9, 18.18530—Building Code Requirements for Masonry Structures, 4.10530.1—Specification for Masonry Structures, 2.4, 3.6

Bonding, see also Adhesives, Protective systems503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive

506.5R—Guide for Specifying Underground Shotcrete, 16.2

524R—Guide to Portland Cement-Based Plaster, 4.8, 9.5, 9.6, 9.7555R—Removal and Reuse of Hardened Concrete, 4.7

Box girders343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.21

Brackets, see also Corbels318—Building Code Requirements for Structural Concrete, 11.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 11.9350—Code Requirements for Environmental Engineering Concrete Structures, 11.9

Bracing, see also Stability347—Guide to Formwork for Concrete, 2.6

Bridge deck345R—Guide for Concrete Highway Bridge Deck Construction345.2R—Guide for Widening Highway Bridges548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays548.5R—Guide for Polymer Concrete Overlays

ITG-3—Report on Bridge Decks Free of Steel Reinforcement

345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 3, Ch. 4

Bridge repair, see Repair

Bridges (structures)341.2R—Seismic Analysis and Design of Concrete Bridge Systems341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges343R—Analysis and Design of Reinforced Concrete Bridge Structures345.1R—Guide for Maintenance of Concrete Bridge Members345.2R—Guide for Widening Highway Bridges548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage DecksITG-3—Report on Bridge Decks Free of Steel Reinforcement

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 11224.3R—Joints in Concrete Construction, Ch. 4

229R—Controlled Low-Strength Materials, 2.7308R—Guide to Curing Concrete, 3.2315—Details and Detailing of Concrete Reinforcement, 1.4, 3.6347—Guide to Formwork for Concrete, 6.2363R—Report on High-Strength Concrete, 8.3

Bubblers, see Aeration

Bug holes, see Surface defects

Building code—Masonry530—Building Code Requirements for Masonry Structures

Building code—Structural concrete318—Building Code Requirements for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures350—Code Requirements for Environmental Engineering Concrete Structures359—Code for Concrete Containments530—Building Code Requirements for Masonry Structures

Bulk density, see Properties of concrete

Bundled bars318—Building Code Requirements for Structural Concrete 7.6.6, 12.4350—Code Requirements for Environmental Engineering Concrete Structures, 12.4

Calcium-aluminate cements225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 2, Ch. 3, App., 6.10


Calibration, see Testing

Camber, see also Deflection209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 4

Canal lining117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 9

Cantilevers209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 5.7

Carbon fibers, see also Fibers440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, App. A440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement

549.2R—Thin Reinforced Cementitious Products, 4.4

Carbonation201.2R—Guide to Durable Concrete, 6.6555R—Removal and Reuse of Hardened Concrete, 5.4

Casing (steel)336.1—Specification for the Construction of Drilled Piers, 2.2, 3.3, 3.6336.3R—Design and Construction of Drilled Piers, 4.1, 4.3543R—Design, Manufacture, and Installation of Concrete Piles, 3.3

Cast-in-place anchors, see also Anchorage318—Building Code Requirements for Structural Concrete, App. D

Cast-in-place concrete303R—Guide to Cast-in-Place Architectural Concrete Practice303.1—Standard Specification for Cast-in-Place Architectural Concrete332.1R—Guide to Residential Concrete Construction523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 4, Sec. 7, Sec. 11, Sec. 14362.1R—Guide for the Design of Durable Parking Structures, Ch. 2

Cast-in-place pipe346—Specification for Cast-in-Place Concrete Pipe

Cathodic protection222R—Protection of Metals in Concrete Against Corrosion, 3.4.4222.2R—Corrosion of Prestressing Steels, 4.4

222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 5.5345.1R—Guide for Maintenance of Concrete Bridge Members, 8.3546R—Concrete Repair Guide, 4.7

Cavitation, see also Erosion210R—Erosion of Concrete in Hydraulic Structures, Ch. 2, Part 2

544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.8, 3.6

Cellular concrete, see also Low-density concrete523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units

Cement, see also Cementitious materials, Hydraulic cement

211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials225R—Guide to the Selection and Use of Hydraulic Cements304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing346—Specification for Cast-in-Place Concrete Pipe524R—Guide to Portland Cement-Based Plaster

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 5

207.1R—Guide to Mass Concrete, 2.2212.3R—Chemical Admixtures for Concrete, 3.3213R—Guide for Structural Lightweight-Aggregate Concrete, 4.4221.1R—Report on Alkali-Aggregate Reactivity, 5.5, 9.3223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 2.1229R—Controlled Low-Strength Materials, 3.2230.1R—Report on Soil Cement, 3.2, 7.3234R—Guide for the Use of Silica Fume in Concrete, 1.5, 7.4, 8.2238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.2, 4.6302.1R—Guide for Concrete Floor and Slab Construction, 5.3304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 2.3304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.3305R—Hot Weather Concreting, 2.5307—Code Requirements for Reinforced Concrete Chimneys, 2.2308R—Guide to Curing Concrete, 1.3313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 2.2318—Building Code Requirements for Structural Concrete, 3.2325.11R—Accelerated Techniques for Concrete Paving, 4.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.2350—Code Requirements for Environmental Engineering Concrete Structures, 3.2357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.5363R—Report on High-Strength Concrete, 2.2, 3.5

MCP INDEX IND-9

506R—Guide to Shotcrete, 2.3506.2—Specification for Shotcrete, 2.1530—Building Code Requirements for Masonry Structures, 1.8, 2.2530.1—Specification for Masonry Structures, 2.1, 2.2533R—Guide for Precast Concrete Wall Panels, 4.2

Cement storage225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 7

Cementitious materials, see also Ground granulated blast-furnace slag, Silica fume, Cement

233R—Slag Cement in Concrete and Mortar234R—Guide for the Use of Silica Fume in Concrete

207.4R—Cooling and Insulating Systems for Mass Concrete, 2.5211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, 4.4, 4.5, 4.6230.1R—Report on Soil Cement, 4.8304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 3.4304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.4, 2.8.3304.2R—Placing Concrete by Pumping Methods, 4.5305R—Hot Weather Concreting, 2.6325.10R—Report on Roller-Compacted Concrete Pavements, 3.3325.11R—Accelerated Techniques for Concrete Paving, 4.3350—Code Requirements for Environmental Engineering Concrete Structures, 3.1546R—Concrete Repair Guide, 3.2

Chemical admixtures, see admixtures

Chemical analysis225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 8

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 4.3232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 1.3

Chemical attack201.2R—Guide to Durable Concrete, Ch. 6210R—Erosion of Concrete in Hydraulic Structures, Ch. 4, Ch. 7350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 5

225R—Guide to the Selection and Use of Hydraulic Cements, 6.10234R—Guide for the Use of Silica Fume in Concrete, 5.3503R—Use of Epoxy Compounds with Concrete, 3.3546.2R—Guide to Underwater Repair of Concrete, 2.3

Chemicals350—Code Requirements for Environmental Engineering Concrete Structures, 4.5

Chimneys, see also Silos307—Code Requirements for Reinforced Concrete Chimneys

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 13

Chloride admixtures222R—Protection of Metals in Concrete Against Corrosion, 2.2.4

Circular concrete structures, see Water tanks

Circular wire372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures

350—Code Requirements for Environmental Engineering Concrete Structures, App. G

Circumferential tendons373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons

Clay brick530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 4.3

Clay tile530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 4.3

Cleaning330R—Guide for the Design and Construction of Concrete Parking Lots, 7.7345.1R—Guide for Maintenance of Concrete Bridge Members, 4.3362.2R—Guide for Structural Maintenance of Parking Structures, 4.1372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 4.11373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.11503R—Use of Epoxy Compounds with Concrete, 6.5503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3.10530.1—Specification for Masonry Structures, 3.8533R—Guide for Precast Concrete Wall Panels, 6.5548.5R—Guide for Polymer Concrete Overlays, 8.6

Coarse aggregates, see also Aggregates221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete


304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing

304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, Ch. 1, 2.1, 4.5, 5.2, 5.5, 6.2

211.3R—Guide for Selecting Proportions for No-Slump Concrete, App. A, Ch. 4, 3.5304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 2.2, 9.4

Coatings, see also Protective coatings350.1—Tightness Testing of Environmental Engineering Concrete Structures

350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 5

347—Guide to Formwork for Concrete, 4.4350—Code Requirements for Environmental Engineering Concrete Structures, 4.7372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.9, 3.10373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.10503R—Use of Epoxy Compounds with Concrete, 4.2546R—Concrete Repair Guide, 3.5549R—Report on Ferrocement, 3.6

Code318—Building Code Requirements for Structural Concrete332—Code Requirements for Residential Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures350—Code Requirements for Environmental Engineering Concrete Structures530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

341.2R—Seismic Analysis and Design of Concrete Bridge Systems, Ch. 2423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, Ch. 2439.3R—Types of Mechanical Splices for Reinforcing Bars, Ch. 2

Coefficient of variation214R—Evaluation of Strength Test Results of Concrete

228.1R—In-Place Methods to Estimate Concrete Strength, 2.3, 2.4, 2.6, 3.2, 4.2, 6.2

Cold joints, see Surface defects

Cold storage rooms302.1R—Guide for Concrete Floor and Slab Construction, 9.9

Cold weather concreting306R—Cold Weather Concreting306.1—Standard Specification for Cold Weather ConcretingSP-15—Field Reference Manual

301—Specifications for Structural Concrete, 4.2.2.8, 5.3.2302.1R—Guide for Concrete Floor and Slab Construction, 8.17304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 5.5304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 7.2308R—Guide to Curing Concrete, 1.4, 2.6308.1—Standard Specification for Curing Concrete, 1.7318—Building Code Requirements for Structural Concrete, 5.12330.1—Specification for Unreinforced Concrete Parking Lots, 3.12332—Code Requirements for Residential Concrete, 5.4332.1R—Guide to Residential Concrete Construction, 6.6349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.12350—Code Requirements for Environmental Engineering Concrete Structures, 5.11357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.4506R—Guide to Shotcrete, 8.10506.2—Specification for Shotcrete, 3.10506.5R—Guide for Specifying Underground Shotcrete, 11.4522R—Pervious Concrete, 7.6, 10.1522.1—Specification for Pervious Concrete Pavement, 3.11523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.7544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.5

Color, see also Surface defects309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces

212.3R—Chemical Admixtures for Concrete, 6.6233R—Slag Cement in Concrete and Mortar, 5.6234R—Guide for the Use of Silica Fume in Concrete, 2.1, 4.7308R—Guide to Curing Concrete, 3.4.8524R—Guide to Portland Cement-Based Plaster, 12.2

Columns216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, App. A through C, 2.5, 2.6, 3.4, 3.6, 4.4, 4.7343R—Analysis and Design of Reinforced Concrete Bridge Structures352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures441R—High-Strength Concrete Columns

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, App. DITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 5

213R—Guide for Structural Lightweight-Aggregate Concrete, 5.8313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 4.7315—Details and Detailing of Concrete Reinforcement, 2.6

MCP INDEX IND-11

318—Building Code Requirements for Structural Concrete, 7.8, 8.10, 11.10, 15.3, 15.8341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges, 4.1349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.8, 11.11, 12.17350—Code Requirements for Environmental Engineering Concrete Structures, 7.8, 8.8, 10.15, 11.11, 12.17, 15.3, 15.8363R—Report on High-Strength Concrete, 6.2, 6.4423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.7530—Building Code Requirements for Masonry Structures, 2.1

Column-slab connection, see also Slab-column connection

550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures

421.1R—Guide to Shear Reinforcement for Slabs, Ch. 7

Compacted fill229R—Controlled Low-Strength Materials, Ch. 1

Compacting, see also Consolidation207.5R—Roller-Compacted Mass Concrete

Compaction, see also Consolidation207.5R—Roller-Compacted Mass Concrete, 5.5230.1R—Report on Soil Cement, 7.3, 8.6544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.2

Components, nuclear reactors359—Code for Concrete Containments

Composite compression members318—Building Code Requirements for Structural Concrete, 10.13349—Code Requirements for Nuclear Safety-Related Concrete Structures, 10.16350—Code Requirements for Environmental Engineering Concrete Structures, 10.16

Composite construction318—Building Code Requirements for Structural Concrete, 9.5.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, 2.5, 2.6ITG-3—Report on Bridge Decks Free of Steel Reinforcement, 3.1

Composite materials548.1R—Guide for the Use of Polymers in Concrete, 3.1

Compression field theory445R—Recent Approaches to Shear Design of Structural Concrete, Ch. 2

Compression tests214R—Evaluation of Strength Test Results of Concrete

214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results

Compressive strength, see also Strength207.5R—Roller-Compacted Mass Concrete212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete213R—Guide for Structural Lightweight-Aggregate Concrete214R—Evaluation of Strength Test Results of Concrete214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results228.1R—In-Place Methods to Estimate Concrete Strength228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures301—Specifications for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures437R—Strength Evaluation of Existing Concrete Buildings544.4R—Design Considerations for Steel Fiber-Reinforced Concrete

233R—Slag Cement in Concrete and Mortar, Ch. 5307—Code Requirements for Reinforced Concrete Chimneys, Ch. 3506.1R—Guide to Fiber-Reinforced Shotcrete, 7.2

506.4R—Guide for the Evaluation of Shotcrete, Ch. 2

506.5R—Guide for Specifying Underground Shotcrete, 8.6

523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.1.1. 7.1.3.4207.1R—Guide to Mass Concrete, 3.2230.1R—Report on Soil Cement, 5.3306R—Cold Weather Concreting, 1.4318—Building Code Requirements for Structural Concrete, 10.8 through 10.10325.10R—Report on Roller-Compacted Concrete Pavements, 5.2325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2363.2R—Guide to Quality Control and Testing of High-Strength Concrete, 4.5364.3R—Guide for Cementitious Repair Material Data Sheet, 5.3

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.3, 12.1

441R—High-Strength Concrete Columns, 3.2.1506.1R—Guide to Fiber-Reinforced Shotcrete, 6.3.1.1, 7.2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.3523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 3.1530—Building Code Requirements for Masonry Structures, 1.2, 1.5549R—Report on Ferrocement, 4.2.2

Computer programs126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database


315—Details and Detailing of Concrete Reinforcement, Ch. 6

Concrete block530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

Concrete brick530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

Concrete construction, see Construction

Concrete design, see Design factors

Concrete durability, see Durability

Concrete equipment, see Equipment

Concrete parking lots, see Parking lots

Concrete paving325.11R—Accelerated Techniques for Concrete Paving325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads

Concrete slabs, see Slabs

Conduits, embedded229R—Controlled Low-Strength Materials, 2.6318—Building Code Requirements for Structural Concrete, 6.3350—Code Requirements for Environmental Engineering Concrete Structures, 6.3

Connections, see also Beam-column joints318—Building Code Requirements for Structural Concrete352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures439.3R—Types of Mechanical Splices for Reinforcing Bars

550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 4551.1R—Tilt-Up Concrete Construction Guide, Ch. 7

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 7.9350—Code Requirements for Environmental Engineering Concrete Structures, 7.9, 16.6357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.17, 6.13533R—Guide for Precast Concrete Wall Panels, 2.6

Connections, mechanical355.2—Qualification of Post-Installed Mechanical Anchors in Concrete439.3R—Types of Mechanical Splices for Reinforcing Bars

Connectors, see Anchorage to concrete

Consistency tests, see also Mixture proportioning

211.3R—Guide for Selecting Proportions for No-Slump Concrete, 2.2223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 4.4229R—Controlled Low-Strength Materials, 7.3325.10R—Report on Roller-Compacted Concrete Pavements, 4.2325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 7.1544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 4.2

Consolidation126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing309R—Guide for Consolidation of Concrete309.1R—Report on Behavior of Fresh Concrete During Vibration309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete SurfacesSP-15—Field Reference Manual

302.1R—Guide for Concrete Floor and Slab Construction, Ch. 8303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 7ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 13, 7.9

201.2R—Guide to Durable Concrete, 3.4214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, 2.2222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 4.3301—Specifications for Structural Concrete, 5.3, 6.3, 7.3325.10R—Report on Roller-Compacted Concrete Pavements, 7.5336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, 6.8345R—Guide for Concrete Highway Bridge Deck Construction, 9.5362.1R—Guide for the Design of Durable Parking Structures, 4.6

Construction121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001224.3R—Joints in Concrete Construction302.1R—Guide for Concrete Floor and Slab Construction305R—Hot Weather Concreting306.1—Standard Specification for Cold Weather Concreting318—Building Code Requirements for Structural Concrete330R—Guide for the Design and Construction of Concrete Parking Lots

MCP INDEX IND-13

332.1R—Guide to Residential Concrete Construction336.1—Specification for the Construction of Drilled Piers349—Code Requirements for Nuclear Safety-Related Concrete Structures440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry StructuresITG-7—Specification for Tolerances for Precast Concrete

222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, Ch. 4307—Code Requirements for Reinforced Concrete Chimneys, Ch. 3325.11R—Accelerated Techniques for Concrete Paving, Ch. 5345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 4345.2R—Guide for Widening Highway Bridges, Ch. 3350—Code Requirements for Environmental Engineering Concrete Structures, Part 3, 19.5, G.4351.3R—Foundations for Dynamic Equipment, Ch. 5357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, Ch. 6358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, Ch. 2371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 4372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, Ch. 4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, Ch. 4440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement522R—Pervious Concrete, Ch. 7551.1R—Tilt-Up Concrete Construction Guide, Ch. 6ITG-3—Report on Bridge Decks Free of Steel Reinforcement, Ch. 8

336.3R—Design and Construction of Drilled Piers, 5.3, 5.7, 5.9341.2R—Seismic Analysis and Design of Concrete Bridge Systems, 5.5548.3R—Report on Polymer-Modified Concrete, 4.1.5, 4.3.8, 549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 5.2549R—Report on Ferrocement, Ch. 3

Construction joints, see also Joints, Connections224.3R—Joints in Concrete Construction

325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 4

318—Building Code Requirements for Structural Concrete, 6.4325.10R—Report on Roller-Compacted Concrete Pavements, 7.6346—Specification for Cast-in-Place Concrete Pipe, 3.2

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 6.4350—Code Requirements for Environmental Engineering Concrete Structures, 6.4351.2R—Foundations for Static Equipment, 5.4351.3R—Foundations for Dynamic Equipment, 5.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.3423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.1

Construction loads, see also Loads347.2R—Guide for Shoring/Reshoring of Concrete Multistory Buildings, Ch. 3

334.3R—Construction of Concrete Shells Using Inflated Forms, 3.15551.1R—Tilt-Up Concrete Construction Guide, 4.1

Construction materials, see Materials

Construction specification, see also Specifications

117—Specifications for Tolerances for Concrete Construction and Materials301—Specifications for Structural Concrete303.1—Standard Specification for Cast-in-Place Architectural Concrete306.1—Standard Specification for Cold Weather Concreting308.1—Standard Specification for Curing Concrete330.1—Specification for Unreinforced Concrete Parking Lots336.1—Specification for the Construction of Drilled Piers346—Specification for Cast-in-Place Concrete Pipe423.7—Specification for Unbonded Single-Strand Tendon Materials503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System503.4—Standard Specification for Repairing Concrete with Epoxy Mortars506.2—Specification for Shotcrete530.1—Specification for Masonry Structures548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays

Containment350.2R—Concrete Structures for Containment of Hazardous Materials359—Code for Concrete Containments

372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, Ch. 5373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, Ch. 5


357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 4.5.3

Contract documents, see Specifications

Contraction joints, see also Joints, movement224.3R—Joints in Concrete Construction

207.5R—Roller-Compacted Mass Concrete, 4.5216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.2.7, 3.3.3, 4.6318—Building Code Requirements for Structural Concrete, 22.3325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 4.4360R—Design of Slabs-on-Ground, 13.14544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.7

Contractor533.1R—Design Responsibility for Architectural Precast-Concrete Projects

301—Specifications for Structural Concrete, 1.6.3311.4R—Guide for Concrete Inspection, 2.5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 6.1

Controlled density fill, see Controlledlow-strength materials

Controlled low-strength materials229R—Controlled Low-Strength MaterialsSP-15—Field Reference Manual

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 6.2232.2R—Use of Fly Ash in Concrete, 8.2

Conveying, see also Placing304.4R—Placing Concrete with Belt Conveyors

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 10

207.5R—Roller-Compacted Mass Concrete, 5.4301—Specifications for Structural Concrete, 5.1, 6.1, 7.1, 9.1318—Building Code Requirements for Structural Concrete, 5.9349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.9350—Code Requirements for Environmental Engineering Concrete Structures, 5.8

Cooling207.4R—Cooling and Insulating Systems for Mass Concrete, Ch. 2, Ch. 3

207.1R—Guide to Mass Concrete, 4.7305R—Hot Weather Concreting, 3.2

Cooling system207.4R—Cooling and Insulating Systems for Mass Concrete

Cooling tower117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 13

Corbels, shear design, see also Shear strength445R—Recent Approaches to Shear Design of Structural Concrete, Ch. 6

318—Building Code Requirements for Structural Concrete, 11.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 11.9350—Code Requirements for Environmental Engineering Concrete Structures, 11.9530—Building Code Requirements for Masonry Structures, 1.12

Cores, concrete, see also Testing214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 2.2349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures, 3.5364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, 5.5437R—Strength Evaluation of Existing Concrete Buildings, 3.1506.4R—Guide for the Evaluation of Shotcrete, 2.2

Cores, steel, see also Composite construction543R—Design, Manufacture, and Installation of Concrete Piles, 3.4, 5.4

Corrosion, see also Durability222R—Protection of Metals in Concrete Against Corrosion222.2R—Corrosion of Prestressing Steels222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons


225R—Guide to the Selection and Use of Hydraulic Cements, 6.8233R—Slag Cement in Concrete and Mortar, 5.13234R—Guide for the Use of Silica Fume in Concrete, 5.3315—Details and Detailing of Concrete Reinforcement, 2.11318—Building Code Requirements for Structural Concrete, 18.16343R—Analysis and Design of Reinforced Concrete Bridge Structures, 6.2.3349—Code Requirements for Nuclear Safety-Related Concrete Structures, 4.4350—Code Requirements for Environmental Engineering Concrete Structures, 4.4, 18.16423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.3546.2R—Guide to Underwater Repair of Concrete, 2.4

MCP INDEX IND-15

546.3R—Guide for the Selection of Materials for the Repair of Concrete, A.6555R—Removal and Reuse of Hardened Concrete, 5.4ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 3.7

Couplers – post-tensioning550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 5

318—Building Code Requirements for Structural Concrete, 18.21349—Code Requirements for Nuclear Safety-Related Concrete Structures, 18.21350—Code Requirements for Environmental Engineering Concrete Structures, 18.21423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 5.3423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.4439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities, 3.7, 4.5, 5.7440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.3530—Building Code Requirements for Masonry Structures, 4.8

Coupling sleeve, see Connections, mechanical

Cover, see also Durability216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.3, 2.4, App. A306R—Cold Weather Concreting, 7.6318—Building Code Requirements for Structural Concrete, 7.7332—Code Requirements for Residential Concrete, 4.3345R—Guide for Concrete Highway Bridge Deck Construction, 2.4350.2R—Concrete Structures for Containment of Hazardous Materials, 2.3362.1R—Guide for the Design of Durable Parking Structures, 4.2423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 4.4423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 2.2441R—High-Strength Concrete Columns, 2.1549R—Report on Ferrocement, 5.7

Crack control, see also Durability224R—Control of Cracking in Concrete Structures

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, Ch. 1224.2R—Cracking of Concrete Members in Direct Tension, Ch. 5ITG-3—Report on Bridge Decks Free of Steel Reinforcement, App. B, 3.15

343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.11358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 5.8523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.7

Cracking, see also Cracks207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete224R—Control of Cracking in Concrete Structures224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures503.7—Specification for Crack Repair by Epoxy Injection

349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures, Ch. 3503.5R—Guide for the Selection of Polymer Adhesives with Concrete, Ch. 7ITG-3—Report on Bridge Decks Free of Steel Reinforcement, App. A, App. C, 5.4

201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.1201.2R—Guide to Durable Concrete, 3.6209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 3.4214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Test Results, 2.4221.1R—Report on Alkali-Aggregate Reactivity, 2.2222.2R—Corrosion of Prestressing Steels, 3.4, 3.6222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 2.3223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 1.2225R—Guide to the Selection and Use of Hydraulic Cements, 6.1302.1R—Guide for Concrete Floor and Slab Construction, 9.6, 11.2309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 3.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.13345R—Guide for Concrete Highway Bridge Deck Construction, 1.3

Cracks, see also Crack control, Cracking224R—Control of Cracking in Concrete Structures224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures224.2R—Cracking of Concrete Members in Direct TensionSP-15—Field Reference Manual

446.3R—Finite Element Analysis of Fracture in Concrete Structures, Ch. 2, Ch. 3

330R—Guide for the Design and Construction of Concrete Parking Lots, 7.3345.1R—Guide for Maintenance of Concrete Bridge Members, 7.3, 7.4346—Specification for Cast-in-Place Concrete Pipe, 3.3355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 8.6, A3.2440.4R—Prestressing Concrete Structures with FRP Tendons, 4.3506.1R—Guide to Fiber-Reinforced Shotcrete, 7.6524R—Guide to Portland Cement-Based Plaster, 15.2546.3R—Guide for the Selection of Materials for the Repair of Concrete, 3.2


Creep, see also Deflections209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete

209.1R—Report on Factors Affecting Shrinkage and Creep of Hardened Concrete, Ch. 3224R—Control of Cracking in Concrete Structures, Ch. 7

207.1R—Guide to Mass Concrete, 3.4207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.4207.5R—Roller-Compacted Mass Concrete, 3.5213R—Guide for Structural Lightweight-Aggregate Concrete, 4.8, 5.7225R—Guide to the Selection and Use of Hydraulic Cements, 6.6233R—Slag Cement in Concrete and Mortar, 5.3343R—Analysis and Design of Reinforced Concrete Bridge Structures, 5.4363R—Report on High-Strength Concrete, 5.14364.3R—Guide for Cementitious Repair Material Data Sheet, 5.13

435R—Control of Deflection in Concrete Structures, 2.6440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 8.4440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.4440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.8440.4R—Prestressing Concrete Structures with FRP Tendons, 3.8503R—Use of Epoxy Compounds with Concrete, 3.7530—Building Code Requirements for Masonry Structures, 1.8.6544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.6549R—Report on Ferrocement, 4.8555R—Removal and Reuse of Hardened Concrete, 5.4

Crosstie, see Forming

Culverts117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 10

523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 7.3

Curing308R—Guide to Curing Concrete308.1—Standard Specification for Curing Concrete503.5R—Guide for the Selection of Polymer Adhesives with ConcreteSP-15—Field Reference Manual

302.1R—Guide for Concrete Floor and Slab Construction, Ch. 9, 5.6303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 8305R—Hot Weather Concreting, Ch. 4306R—Cold Weather Concreting, Ch. 8

345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 11351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, Ch. 8364.3R—Guide for Cementitious Repair Material Data Sheet, 5.2


524R—Guide to Portland Cement-Based Plaster, Ch. 13544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, Ch. 8ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 10ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 14, 17.10

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 11.11207.1R—Guide to Mass Concrete, 4.4207.5R—Roller-Compacted Mass Concrete, 5.9214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, 2.3222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 4.4223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 5.3230.1R—Report on Soil Cement, 7.6233R—Slag Cement in Concrete and Mortar, 5.5234R—Guide for the Use of Silica Fume in Concrete, 9.6, 9.7237R—Self-Consolidating Concrete, 6.7301—Specifications for Structural Concrete, 5.3, 8.3, 10.3302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, 6.9, 9.7304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 4.10305.1—Specification for Hot Weather Concreting, 3.7306.1—Standard Specification for Cold Weather Concreting, 3.3307—Code Requirements for Reinforced Concrete Chimneys, 3.7311.6—Specification for Ready Mixed Concrete Testing Services, 2.5313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.7318—Building Code Requirements for Structural Concrete, 5.11325.10R—Report on Roller-Compacted Concrete Pavements, 7.7330R—Guide for the Design and Construction of Concrete Parking Lots, 5.6330.1—Specification for Unreinforced Concrete Parking Lots, 3.11332—Code Requirements for Residential Concrete, 8.7332.1R—Guide to Residential Concrete Construction, 4.6, 5.6334.1R—Concrete Shell Structures Practice, 7.3346—Specification for Cast-in-Place Concrete Pipe, 3.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.11350—Code Requirements for Environmental Engineering Concrete Structures, 5.10, H.7350.2R—Concrete Structures for Containment of Hazardous Materials, 4.2355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, A3.3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.5

MCP INDEX IND-17

360R—Design of Slabs-on-Ground, 13.11362.1R—Guide for the Design of Durable Parking Structures, 4.8363R—Report on High-Strength Concrete, 4.6363.2R—Guide to Quality Control and Testing of High-Strength Concrete, 3.5423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.4503R—Use of Epoxy Compounds with Concrete, 3.10506R—Guide to Shotcrete, 2.9, 8.8506.2—Specification for Shotcrete, 2.6, 3.8522R—Pervious Concrete, 7.5522.1—Specification for Pervious Concrete Pavement, 3.10523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.6523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 5.1533R—Guide for Precast Concrete Wall Panels, 4.9, 5.7543R—Design, Manufacture, and Installation of Concrete Piles, 4.5546.3R—Guide for the Selection of Materials for the Repair of Concrete, A.2548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks, 3.5548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks, 3.5

Curing compounds308R—Guide to Curing Concrete

330.1—Specification for Unreinforced Concrete Parking Lots, 2.3, 3.11506R—Guide to Shotcrete, 2.9

Curling, see also Slabs360R—Design of Slabs-on-Ground, Ch. 13

201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.2302.1R—Guide for Concrete Floor and Slab Construction, 11.11

Currents, see also Electrical properties357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.18

Curvature friction318—Building Code Requirements for Structural Concrete, 18.6

Cyclic loads, see also Fatigue408.2R—Bond under Cyclic Loads

Cylinders, concrete, see also Testing228.1R—In-Place Methods to Estimate Concrete Strength, 2.8

Dampproofing, see also Admixtures, Protective Systems, Barrier systems

212.3R—Chemical Admixtures for Concrete, 6.9

Dams, see also Mass concrete207.1R—Guide to Mass Concrete

207.5R—Roller-Compacted Mass Concrete, Ch. 4

309.5R—Compaction of Roller-Compacted Concrete, 5.3

Database, see also Materials property database408R—Bond and Development of Straight Reinforcing Bars in Tension, Ch. 5

Decks, bridges345R—Guide for Concrete Highway Bridge Deck Construction548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks

ITG-3—Report on Bridge Decks Free of Steel Reinforcement, Ch. 3, Ch. 6

Deep beams, see Deep flexural members

Deep flexural members318—Building Code Requirements for Structural Concrete, 10.7, 11.7349—Code Requirements for Nuclear Safety-Related Concrete Structures, 10.7, 11.8350—Code Requirements for Environmental Engineering Concrete Structures, 10.7, 11.8

Defects, see Surface defects

Definitions, see Terminology, Notation

Deflection, see also Creep209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures435R—Control of Deflection in Concrete Structures435.8R—Observed Deflections of Reinforced Concrete Slab Systems, and Causes of Large Deflections

437R—Strength Evaluation of Existing Concrete Buildings, Ch. 5

201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.3213R—Guide for Structural Lightweight-Aggregate Concrete, 5.7307—Code Requirements for Reinforced Concrete Chimneys, 4.5318—Building Code Requirements for Structural Concrete, 9.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, 8.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 9.5350—Code Requirements for Environmental Engineering Concrete Structures, 9.5351.2R—Foundations for Static Equipment, 3.3358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 5.7440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.9


440.4R—Prestressing Concrete Structures with FRP Tendons, 3.10, 4.2523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.4523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.4530—Building Code Requirements for Masonry Structures, 1.10

Deformed bars, see also Reinforcement – steel408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

318—Building Code Requirements for Structural Concrete, Ch. 12349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 12350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 12

Degradation of concrete, see also Deterioration349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures, Ch. 4

Deicing salt233R—Slag Cement in Concrete and Mortar, 5.11

Delamination, see Surface defects201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 13.1524R—Guide to Portland Cement-Based Plaster, 15.4

Demolition555R—Removal and Reuse of Hardened Concrete, Ch. 3, 2.2

423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 5.8

Density221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 7

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.4, 4.5230.1R—Report on Soil Cement, 5.2234R—Guide for the Use of Silica Fume in Concrete, 2.3309R—Guide for Consolidation of Concrete, 17.2309.5R—Compaction of Roller-Compacted Concrete, 2.2, 6.3, 6.4364.3R—Guide for Cementitious Repair Material Data Sheet, 5.1

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.1, 3.2, 4.3

Depositing concrete, see Placing

Design examples349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design ExamplesSP-17—ACI Design Handbook

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 15523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, App. C

Design factors318—Building Code Requirements for Structural Concrete330R—Guide for the Design and Construction of Concrete Parking Lots336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats343R—Analysis and Design of Reinforced Concrete Bridge Structures345.2R—Guide for Widening Highway Bridges349—Code Requirements for Nuclear Safety-Related Concrete Structures349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures350.3—Seismic Design of Liquid-Containing Concrete Structures350.4R—Design Considerations for Environmental Engineering Concrete Structures352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures, Ch. 3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures360R—Design of Slabs-on-Ground362.1R—Guide for the Design of Durable Parking Structures371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 5374.1—Acceptance Criteria for Moment Frames Based on Structural Testing435R—Control of Deflection in Concrete Structures440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars 440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures445R—Recent Approaches to Shear Design of Structural Concrete530—Building Code Requirements for Masonry Structures550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete StructuresITG-3—Report on Bridge Decks Free of Steel ReinforcementITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 4.1SP-17—ACI Design Handbook

207.5R—Roller-Compacted Mass Concrete, Ch. 4

MCP INDEX IND-19

210R—Erosion of Concrete in Hydraulic Structures, Ch. 5213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 5222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, Ch. 2307—Code Requirements for Reinforced Concrete Chimneys, Ch. 4313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, Ch. 4325.10R—Report on Roller-Compacted Concrete Pavements, Ch. 6325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 3341.2R—Seismic Analysis and Design of Concrete Bridge Systems, Ch. 5347—Guide to Formwork for Concrete, Ch. 2351.2R—Foundations for Static Equipment, Ch. 3, Ch. 4351.3R—Foundations for Dynamic Equipment, Ch. 3357.2R—Report on Barge-Like Concrete Structures, Ch. 5408R—Bond and Development of Straight Reinforcing Bars in Tension, Ch. 4421.1R—Guide to Shear Reinforcement for Slabs, Ch. 4423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, Ch. 2, Ch. 3439.3R—Types of Mechanical Splices for Reinforcing Bars, Ch. 2440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 3506.1R—Guide to Fiber-Reinforced Shotcrete, Ch. 8522R—Pervious Concrete, Ch. 6524R—Guide to Portland Cement-Based Plaster, Ch. 5ITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation Testing, Ch. 3

222R—Protection of Metals in Concrete Against Corrosion, 3.2309R—Guide for Consolidation of Concrete, 8.1309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 2.1533R—Guide for Precast Concrete Wall Panels, 2.2544.1R—Report on Fiber-Reinforced Concrete, 2.5549R—Report on Ferrocement, 5.2549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 4.1

DetailingITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 13.2


Detailing of reinforcement315—Details and Detailing of Concrete Reinforcement439.4R—Report on Steel Reinforcement—Material Properties and U.S. AvailabilitiesSP-66—ACI Detailing Manual

303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 5318—Building Code Requirements for Structural Concrete, Ch. 7349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 7350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 7

222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 2.4309R—Guide for Consolidation of Concrete, 8.1530—Building Code Requirements for Masonry Structures, 1.13

Deterioration222.2R—Corrosion of Prestressing Steels, Ch. 3345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 2362.1R—Guide for the Design of Durable Parking Structures, Ch. 3

201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 3.5524R—Guide to Portland Cement-Based Plaster, 15.6

Development length, see also Reinforcement – steel

408R—Bond and Development of Straight Reinforcing Bars in Tension408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 12440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 6ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 7, 8.5

213R—Guide for Structural Lightweight-Aggregate Concrete, 5.6315—Details and Detailing of Concrete Reinforcement, 2.7440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 11.2

Dimensions, see Tolerances

Discoloration, see Surface defects

Documentation364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, Ch. 3

Dowel, bar connectors325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 4.1439.3R—Types of Mechanical Splices for Reinforcing Bars, 3.4


Drainage345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 4350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 7

207.5R—Roller-Compacted Mass Concrete, 5.10302.1R—Guide for Concrete Floor and Slab Construction, 11.10332.1R—Guide to Residential Concrete Construction, 3.13345R—Guide for Concrete Highway Bridge Deck Construction, 2.2362.1R—Guide for the Design of Durable Parking Structures, 3.2, 4.4

Drawings315—Details and Detailing of Concrete Reinforcement

307—Code Requirements for Reinforced Concrete Chimneys, 1.2313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 1.4318—Building Code Requirements for Structural Concrete, 1.2332—Code Requirements for Residential Concrete, 1.4349—Code Requirements for Nuclear Safety-Related Concrete Structures, 1.2350—Code Requirements for Environmental Engineering Concrete Structures, 1.2371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 1.3440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 14.2533.1R—Design Responsibility for Architectural Precast-Concrete Projects, 2.4ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 1.3

Drift ratio, see also Deflection374.1—Acceptance Criteria for Moment Frames Based on Structural TestingT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, Ch. 4, 5

421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates, 2.2ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, 5.4

Drilled piers336.1—Specification for the Construction of Drilled Piers336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats336.3R—Design and Construction of Drilled Piers


228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures, 2.3

Drying302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, Ch. 2, Ch. 6

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 2.1

Drying shrinkage224R—Control of Cracking in Concrete Structures

360R—Design of Slabs-on-Ground, Ch. 13

207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 4.2212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.5213R—Guide for Structural Lightweight-Aggregate Concrete, 4.9224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 1.3234R—Guide for the Use of Silica Fume in Concrete, 10.4523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.4523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 3.2

Ductility357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, App. B421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates, Ch. 4439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities, 3.2.1440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 7.6440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 12.3441R—High-Strength Concrete Columns, 3.2550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, 3.2

Ducts, as in Conduits350—Code Requirements for Environmental Engineering Concrete Structures, 6.3549.2R—Thin Reinforced Cementitious Products, 5.4

Ducts, for post-tensioning222.2R—Corrosion of Prestressing Steels, 4.3318—Building Code Requirements for Structural Concrete, 18.17350—Code Requirements for Environmental Engineering Concrete Structures, 18.17357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.11, 6.7T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 3.2

Durability, see also Corrosion, cracks201.1R—Guide for Conducting a Visual Inspection of Concrete in Service201.2R—Guide to Durable Concrete

MCP INDEX IND-21

221.1R—Report on Alkali-Aggregate Reactivity301—Specifications for Structural Concrete

318—Building Code Requirements for Structural Concrete, Ch. 4350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, Ch. 2362.1R—Guide for the Design of Durable Parking Structures, Ch. 3440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 11, 5.4440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 4

207.1R—Guide to Mass Concrete, 3.9207.5R—Roller-Compacted Mass Concrete, 3.10212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.7213R—Guide for Structural Lightweight-Aggregate Concrete, 4.14221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 2.1234R—Guide for the Use of Silica Fume in Concrete, 5.3237R—Self-Consolidating Concrete, 3.3304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 1.6

309.5R—Compaction of Roller-Compacted Concrete, 3.4325.10R—Report on Roller-Compacted Concrete Pavements, 5.8325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2330R—Guide for the Design and Construction of Concrete Parking Lots, 4.3350.2R—Concrete Structures for Containment of Hazardous Materials, 2.4365.1R—Service-Life Prediction, 7.2440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.5440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, Ch. 9522R—Pervious Concrete, 4.6544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 3.6, 3.7549R—Report on Ferrocement, 4.9, 5.10

Dusting, see also Curing201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.9302.1R—Guide for Concrete Floor and Slab Construction, 11.4

Dynamic equipment, see Equipment foundations

Dynamic fracture446.4R—Report on Dynamic Fracture of Concrete

Dynamic load effects, see also Fatigue350.3—Seismic Design of Liquid-Containing Concrete Structures408.2R—Bond under Cyclic Loads

544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.9

Dynamic properties of concrete446.4R—Report on Dynamic Fracture of Concrete

207.5R—Roller-Compacted Mass Concrete, 3.4350.3—Seismic Design of Liquid-Containing Concrete Structures, 3.1

Earthquake requirements and loading, see also Seismic

350.3—Seismic Design of Liquid-Containing Concrete Structures374.1—Acceptance Criteria for Moment Frames Based on Structural Testing408.2R—Bond under Cyclic Loads550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete StructuresT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 21357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, App. B

307—Code Requirements for Reinforced Concrete Chimneys, 4.3355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 9.5, 9.6372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 4.7423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.5

Electrical properties, see also Currents503R—Use of Epoxy Compounds with Concrete, 3.4

Embedded conduits and pipes, see also Conduits or Ducts

530—Building Code Requirements for Masonry Structures

207.4R—Cooling and Insulating Systems for Mass Concrete, 3.2318—Building Code Requirements for Structural Concrete, 6.3349—Code Requirements for Nuclear Safety-Related Concrete Structures, 6.3350—Code Requirements for Environmental Engineering Concrete Structures, 6.3

Embedment of items in concrete, see also Anchorage

349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples


117—Specifications for Tolerances for Concrete Construction and Materials, 2.3, 7.5


222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 3.5304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 5.3306R—Cold Weather Concreting, 4.2336.1—Specification for the Construction of Drilled Piers, 3.8350—Code Requirements for Environmental Engineering Concrete Structures, 6.3, 16.7357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.17362.1R—Guide for the Design of Durable Parking Structures, 3.4543R—Design, Manufacture, and Installation of Concrete Piles, 4.4551.1R—Tilt-Up Concrete Construction Guide, 5.4, 5.5

Empirical design530—Building Code Requirements for Masonry Structures, Ch. 5

Energy dissipation374.1—Acceptance Criteria for Moment Frames Based on Structural Testing, 9.0T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 4.4

Engineered demolition, see Demolition

Environmental considerations, see also Chemical attack, Marine concrete, and Hot and Cold weather concreting

222R—Protection of Metals in Concrete Against Corrosion350.4R—Design Considerations for Environmental Engineering Concrete Structures

207.5R—Roller-Compacted Mass Concrete, 5.9221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 4.6222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 2.2233R—Slag Cement in Concrete and Mortar, 1.4305R—Hot Weather Concreting, 4.4308R—Guide to Curing Concrete, 1.4, 2.6, 2.7, 4.2, 4.4313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.7362.1R—Guide for the Design of Durable Parking Structures, 4.13423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.5

Environmental engineering, see also Water tanks

350—Code Requirements for Environmental Engineering Concrete Structures350.1—Tightness Testing of Environmental Engineering Concrete Structures350.2R—Concrete Structures for Containment of Hazardous Materials350.4R—Design Considerations for Environmental Engineering Concrete Structures

Epoxy, see also Adhesive or Polymer adhesives351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery503R—Use of Epoxy Compounds with Concrete503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System503.4—Standard Specification for Repairing Concrete with Epoxy Mortars503.5R—Guide for the Selection of Polymer Adhesives with Concrete503.7—Specification for Crack Repair by Epoxy Injection548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks

224R—Control of Cracking in Concrete Structures, 6.3224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.2372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.8373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.8, 2.9546.2R—Guide to Underwater Repair of Concrete, 6.6, 6.7548.3R—Report on Polymer-Modified Concrete, 4.2548.5R—Guide for Polymer Concrete Overlays, 2.3

Epoxy resin311.1R—ACI Manual of Concrete Inspection

548.3R—Report on Polymer-Modified Concrete, Ch. 4

357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.20440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 4.2440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.1

Equipment304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing345R—Guide for Concrete Highway Bridge Deck Construction

304.2R—Placing Concrete by Pumping Methods, Ch. 2304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Ch. 3309R—Guide for Consolidation of Concrete, Ch. 5506R—Guide to Shotcrete, Ch. 3555R—Removal and Reuse of Hardened Concrete, Ch. 3506.5R—Guide for Specifying Underground Shotcrete, Ch. 13, Ch. 14

MCP INDEX IND-23

318—Building Code Requirements for Structural Concrete, 5.7325.11R—Accelerated Techniques for Concrete Paving, 3.5330R—Guide for the Design and Construction of Concrete Parking Lots, 5.4349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.7350—Code Requirements for Environmental Engineering Concrete Structures, 5.6351.2R—Foundations for Static Equipment, 5.5351.3R—Foundations for Dynamic Equipment, 5.5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 6.3503R—Use of Epoxy Compounds with Concrete, 6.5

543R—Design, Manufacture, and Installation of Concrete Piles, 5.1548.5R—Guide for Polymer Concrete Overlays, 8.8

Equipment foundations351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery351.2R—Foundations for Static Equipment351.3R—Foundations for Dynamic Equipment

Erection tolerances, see also Tolerances533R—Guide for Precast Concrete Wall Panels, Ch. 3ITG-7—Specification for Tolerances for Precast Concrete

530.1—Specification for Masonry Structures, 3.3

Erosion, see also Abrasion210R—Erosion of Concrete in Hydraulic Structures

345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 2

229R—Controlled Low-Strength Materials, 2.7350—Code Requirements for Environmental Engineering Concrete Structures, 4.6544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.8

Evaluation, see also Acceptance or Testing207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions210R—Erosion of Concrete in Hydraulic Structures214R—Evaluation of Strength Test Results of Concrete214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures355.2—Qualification of Post-Installed Mechanical Anchors in Concrete364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation437R—Strength Evaluation of Existing Concrete Buildings

222.2R—Corrosion of Prestressing Steels, Ch. 5

308R—Guide to Curing Concrete, Ch. 4350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 20, 3.1, 5.5, 16.10363.2R—Guide to Quality Control and Testing of High-Strength Concrete, Ch. 5423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, Ch. 4506.4R—Guide for the Evaluation of Shotcrete, Ch. 3524R—Guide to Portland Cement-Based Plaster, Ch. 14546R—Concrete Repair Guide, Ch. 2546.2R—Guide to Underwater Repair of Concrete, Ch. 3

209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, 3.5222R—Protection of Metals in Concrete Against Corrosion, 4.2222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 5.2301—Specifications for Structural Concrete, 1.6308R—Guide to Curing Concrete, 2.8318—Building Code Requirements for Structural Concrete, 5.6, 20.1349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.6, 20.1351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 4.4365.1R—Service-Life Prediction, 3.2503R—Use of Epoxy Compounds with Concrete, 5.2503.7—Specification for Crack Repair by Epoxy Injection, 3.1506.2—Specification for Shotcrete, 3.1555R—Removal and Reuse of Hardened Concrete, 2.2

Examination, see also Testing506.2—Specification for Shotcrete, 3.1

Excavation336.1—Specification for the Construction of Drilled Piers, 3.2

Existing structures, see Repair

Expansion, see Alkali-aggregate reactivity or Alkali-silica reactivity

Expansion anchors, see also Anchorage to concrete

355.2—Qualification of Post-Installed Mechanical Anchors in Concrete

Expansion joints, see also Joints224.3R—Joints in Concrete Construction

325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 4.4

Expansive cement, see also Cement223—Standard Practice for the Use of Shrinkage-Compensating Concrete

225R—Guide to the Selection and Use of Hydraulic Cements, 2.2


Exposed aggregate, see also Architectural concrete

303.1—Standard Specification for Cast-in-Place Architectural Concrete, Ch. 5

301—Specifications for Structural Concrete, 6.3304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 1.11

External reinforcement, see Repair

Fabrication, see also Bending of reinforcing steel

315—Details and Detailing of Concrete Reinforcement, Ch. 4549.1R—Guide for the Design, Construction, and Repair of Ferrocement, Ch. 5

550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 6343R—Analysis and Design of Reinforced Concrete Bridge Structures, 13.9423.7—Specification for Unbonded Single-Strand Tendon Materials, 1.6440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 2.2549R—Report on Ferrocement, 3.7

Factor of safety360R—Design of Slabs-on-Ground, 4.9

Failures408.2R—Bond under Cyclic Loads

355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, App. A1

Falsework, see also Formwork345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 5

Fasteners, see Anchorage to concrete

Fatigue, see also Dynamic load effects408.2R—Bond under Cyclic Loads

ITG-3—Report on Bridge Decks Free of Steel Reinforcement, App. B, 5.7

210R—Erosion of Concrete in Hydraulic Structures, 5.4213R—Guide for Structural Lightweight-Aggregate Concrete, 5.12325.10R—Report on Roller-Compacted Concrete Pavements, 5.6355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 8.5358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 5.5363R—Report on High-Strength Concrete, 5.7440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 6.4, 7.4

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.4440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.7440.4R—Prestressing Concrete Structures with FRP Tendons, 4.4549R—Report on Ferrocement, 4.5

Ferrocement549R—Report on Ferrocement549.1R—Guide for the Design, Construction, and Repair of Ferrocement549.2R—Thin Reinforced Cementitious Products

Fiber-reinforced concrete, see also Fibers440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures440.4R—Prestressing Concrete Structures with FRP Tendons506.1R—Guide to Fiber-Reinforced Shotcrete

544.2R—Measurement of Properties of Fiber-Reinforced Concrete544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete544.4R—Design Considerations for Steel Fiber-Reinforced Concrete


224R—Control of Cracking in Concrete Structures, 6.2304.2R—Placing Concrete by Pumping Methods, 4.7350.2R—Concrete Structures for Containment of Hazardous Materials, 2.6506.2—Specification for Shotcrete, 2.8506.5R—Guide for Specifying Underground Shotcrete, 5.4

Fiber-reinforced polymer (FRP) reinforcement440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures440.4R—Prestressing Concrete Structures with FRP Tendons

440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars

440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement

549.2R—Thin Reinforced Cementitious Products, 4.3

Fibers440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars

MCP INDEX IND-25

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures440.4R—Prestressing Concrete Structures with FRP Tendons440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement506.1R—Guide to Fiber-Reinforced Shotcrete544.1R—Report on Fiber-Reinforced Concrete544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete549.2R—Thin Reinforced Cementitious Products

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 9ITG-3—Report on Bridge Decks Free of Steel Reinforcement, App. C, 8.3, 8.4

234R—Guide for the Use of Silica Fume in Concrete, 5.5304.2R—Placing Concrete by Pumping Methods, 4.7440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 4.3506.5R—Guide for Specifying Underground Shotcrete, 5.4524R—Guide to Portland Cement-Based Plaster, 4.7

Field-cured specimens, see also Testing306R—Cold Weather Concreting, 6.2

Field practice, see also Construction304.2R—Placing Concrete by Pumping Methods, Ch. 5

Field tests, see also Testing311.4R—Guide for Concrete Inspection, App. I311.5—Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete, Ch. 2311.6—Specification for Ready Mixed Concrete Testing Services, Sec. 2

Fills, see also Controlled low-strength materials229R—Controlled Low-Strength Materials, Ch. 2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, Ch. 7

Fine aggregates, see also Aggregates221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete

304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.2

Finishes303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 9524R—Guide to Portland Cement-Based Plaster, Ch. 12

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, Ch. 5301—Specifications for Structural Concrete, 5.3, 6.3, 7.3318—Building Code Requirements for Structural Concrete, 8.14343R—Analysis and Design of Reinforced Concrete Bridge Structures, 6.9

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.12350—Code Requirements for Environmental Engineering Concrete Structures, 8.12371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.1.5, App. 4523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 5.5, 5.6533R—Guide for Precast Concrete Wall Panels, 5.6

Finishing117—Specifications for Tolerances for Concrete Construction and Materials230.1R—Report on Soil Cement544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.4

223—Standard Practice for the Use of Shrinkage-Compensating Concrete, Ch. 5237R—Self-Consolidating Concrete, Ch. 6302.1R—Guide for Concrete Floor and Slab Construction, Ch. 8, 2.5303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 10ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 13, 17.9

234R—Guide for the Use of Silica Fume in Concrete, 9.5304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 6.3, 7.10304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 4.9305R—Hot Weather Concreting, 4.3305.1—Specification for Hot Weather Concreting, 3.5313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.6330R—Guide for the Design and Construction of Concrete Parking Lots, 5.5330.1—Specification for Unreinforced Concrete Parking Lots, 3.6, 3.7332.1R—Guide to Residential Concrete Construction, 5.4345R—Guide for Concrete Highway Bridge Deck Construction, 10.2 through 10.4346—Specification for Cast-in-Place Concrete Pipe, 3.2362.1R—Guide for the Design of Durable Parking Structures, 4.7506R—Guide to Shotcrete, 8.6506.2—Specification for Shotcrete, 3.7522.1—Specification for Pervious Concrete Pavement, 3.5, 3.6523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.5544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.4

Finishing equipment, see Equipment

Finite element analysis446.3R—Finite Element Analysis of Fracture in Concrete Structures


224.2R—Cracking of Concrete Members in Direct Tension, 4.2

Fire resistance and protection216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies

523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, Ch. 8

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.19423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.4440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 12.2440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 1.3, 9.2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.9549R—Report on Ferrocement, 4.10

Fixed offshore structures357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures

Flat plate, see also Slabs352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures421.1R—Guide to Shear Reinforcement for Slabs421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates435.8R—Observed Deflections of Reinforced Concrete Slab Systems, and Causes of Large Deflections


423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.3

Flat slab, see also Slabs352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures

423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.3

Flexure318—Building Code Requirements for Structural Concrete, Ch. 10350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 10440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 8440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 10

Flexural member318—Building Code Requirements for Structural Concrete, Ch. 17, 7.11, 8.4, 10.4, 10.5, 18.4, 18.8

349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 17, 7.11, 8.4, 10.4, 10.5, 10.7, 11.8, 18.4, 18.8, 21.3350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 17, App. B, 7.11, 8.4, 10.4, 10.5, 18.4, 21.3435R—Control of Deflection in Concrete Structures, Ch. 2, Ch. 3440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 10

209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 3.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, 8.4, 8.6, 13.4

Flexural reinforcement, see Reinforcement – steel or Reinforcement – FRP

Flexural strength


440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 10441R—High-Strength Concrete Columns, Ch. 3

230.1R—Report on Soil Cement, 5.4307—Code Requirements for Reinforced Concrete Chimneys, 5.5325.10R—Report on Roller-Compacted Concrete Pavements, 5.3325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2350—Code Requirements for Environmental Engineering Concrete Structures, 18.7364.3R—Guide for Cementitious Repair Material Data Sheet, 5.4

506.1R—Guide to Fiber-Reinforced Shotcrete, 6.3.1.2, 7.1

506.5R—Guide for Specifying Underground Shotcrete, 8.7544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.4549R—Report on Ferrocement, 4.2.3549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 4.2555R—Removal and Reuse of Hardened Concrete, 5.4ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 6.6T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 6.5

Floating structures357.2R—Report on Barge-Like Concrete Structures

Floors, see also Slabs302.1R—Guide for Concrete Floor and Slab Construction302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials

MCP INDEX IND-27

523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units

201.2R—Guide to Durable Concrete, Ch. 8309R—Guide for Consolidation of Concrete, Ch. 10, 13.5435R—Control of Deflection in Concrete Structures, Ch. 4

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.2, 2.4301—Specifications for Structural Concrete, 2.2, 2.3, 4.1, 4.2, 5.3, 7.2308R—Guide to Curing Concrete, 3.4318—Building Code Requirements for Structural Concrete, 1.3.2, 6.4.4, 8.10, 8.14, 9.5, 10.15349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.12, 10.15350—Code Requirements for Environmental Engineering Concrete Structures, 8.12, 10.15362.1R—Guide for the Design of Durable Parking Structures, 3.6, 4.4371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.2.1, 4.3.1.1, 5.3.1, 5.3.1.2, 5.3.1.3, 5.3.2.3, 5.3.2.4, 7.8372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.2373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 3.2523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 5.3, 6.3

Flowability, see Rheology or Workability

Flowable fill229R—Controlled Low-Strength Materials, 2.3

Fly ash, see also Cementitious materials211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials232.2R—Use of Fly Ash in Concrete

229R—Controlled Low-Strength Materials, 3.3234R—Guide for the Use of Silica Fume in Concrete, 3.8

Foams, see Cellular concrete, Controlled low-strength materials, Low-density concrete

Folded plates, see also Shells334.1R—Concrete Shell Structures Practice

318—Building Code Requirements for Structural Concrete, Ch. 19350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 19

347—Guide to Formwork for Concrete, 6.4

Footings, see also Foundations336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats

318—Building Code Requirements for Structural Concrete, Ch. 15, 22.7332—Code Requirements for Residential Concrete, Ch. 6, 1.3332.1R—Guide to Residential Concrete Construction, Ch. 3349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 15350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 15, 11.12

341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges, 4.4372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.2551.1R—Tilt-Up Concrete Construction Guide, 3.2, 3.3

Forms, see Formwork

Forms – inflated334.3R—Construction of Concrete Shells Using Inflated Forms

Formwork, see also Construction304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces347—Guide to Formwork for Concrete347.2R—Guide for Shoring/Reshoring of Concrete Mutistory BuildingsSP-4—Formwork for ConcreteSP-15—Field Reference Manual

301—Specifications for Structural Concrete, Sec. 2303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 4304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Ch. 4309R—Guide for Consolidation of Concrete, Ch. 6, 5.2318—Building Code Requirements for Structural Concrete, Ch. 6345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 5349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 6440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 9551.1R—Tilt-Up Concrete Construction Guide, Ch. 5

207.1R—Guide to Mass Concrete, 4.5207.5R—Roller-Compacted Mass Concrete, 5.8223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 3.9302.1R—Guide for Concrete Floor and Slab Construction, 4.2303.1—Standard Specification for Cast-in-Place Architectural Concrete, 4.2304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 4.4306R—Cold Weather Concreting, 5.4, 6.9307—Code Requirements for Reinforced Concrete Chimneys, 3.4308R—Guide to Curing Concrete, 3.4.2309.1R—Report on Behavior of Fresh Concrete During Vibration, 4.4.3


311.4R—Guide for Concrete Inspection, 3.7313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.5315—Details and Detailing of Concrete Reinforcement, 5.3330.1—Specification for Unreinforced Concrete Parking Lots, 2.5, 3.3332—Code Requirements for Residential Concrete, 3.3, 5.3, 8.3332.1R—Guide to Residential Concrete Construction, 3.7, 4.1334.1R—Concrete Shell Structures Practice, 5.2, 7.1350—Code Requirements for Environmental Engineering Concrete Structures, 6.1, 6.2, 17.3351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 6.5351.2R—Foundations for Static Equipment, 5.3351.3R—Foundations for Dynamic Equipment, 5.3371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.1.3372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 4.3373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.3423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.6506R—Guide to Shotcrete, 5.3522.1—Specification for Pervious Concrete Pavement, 2.4, 3.3523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 6.1533R—Guide for Precast Concrete Wall Panels, 5.2543R—Design, Manufacture, and Installation of Concrete Piles, 4.2546.2R—Guide to Underwater Repair of Concrete, 5.1, 5.2549.2R—Thin Reinforced Cementitious Products, 5.8

Foundation stabilization229R—Controlled Low-Strength Materials230.1R—Report on Soil Cement, 3.6307—Code Requirements for Reinforced Concrete Chimneys, Ch. 4313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials336.3R—Design and Construction of Drilled Piers351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery351.2R—Foundations for Static Equipment351.3R—Foundations for Dynamic Equipment357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures

336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, 1.6350.4R—Design Considerations for Environmental Engineering Concrete Structures, 3.2, 4.3

Foundations, see also Drilled piers336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery351.2R—Foundations for Static Equipment351.3R—Foundations for Dynamic Equipment

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 3318—Building Code Requirements for Structural Concrete, Ch. 15, 11.11, 21.12, 22.7334.3R—Construction of Concrete Shells Using Inflated Forms, Ch. 2350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 15551.1R—Tilt-Up Concrete Construction Guide, Ch. 3, 7.2

228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures, 2.3313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 4.8, 7.6341.2R—Seismic Analysis and Design of Concrete Bridge Systems, 4.3343R—Analysis and Design of Reinforced Concrete Bridge Structures, 11.3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 5.4371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.1.3.2, 4.1.7, 5.1.1.1, 5.2.1, 5.2.1.1.2, 5.2.1.3.2, 5.2.1.3.3, 5.2.1.4, 6.2, 6.3, 6.4, 6.44, 6.5372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.2373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 3.2530—Building Code Requirements for Masonry Structures, 5.6.3

Fracture mechanics446.1R—Fracture Mechanics of Concrete: Concepts, Models, and Determination of Material Properties446.4R—Report on Dynamic Fracture of Concrete

224R—Control of Cracking in Concrete Structures, 2.3446.3R—Finite Element Analysis of Fracture in Concrete Structures, 2.2

Frames374.1—Acceptance Criteria for Moment Frames Based on Structural TestingT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures, Ch. 3

315—Details and Detailing of Concrete Reinforcement, 2.10318—Building Code Requirements for Structural Concrete, 21.2, 21.3, 21.5, 21.6, 21.7, 21.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 10.11, 10.12, 10.13350—Code Requirements for Environmental Engineering Concrete Structures, 10.12, 10.13, 13.7, 21.3, 21.4, 21.5, 21.6530—Building Code Requirements for Masonry Structures, 1.14550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 3, 5.2

MCP INDEX IND-29

Freeboard350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 7

Freezing, see also Cold weather306R—Cold Weather Concreting, 5.1306.1—Standard Specification for Cold Weather Concreting, 3.4308R—Guide to Curing Concrete, 2.4330R—Guide for the Design and Construction of Concrete Parking Lots, 5.6, B.5357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.14

Freezing-and-thawing resistance, see also Durability

201.2R—Guide to Durable Concrete, Ch. 4306R—Cold Weather Concreting, Ch. 5 through Ch. 7, 2.6

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.6225R—Guide to the Selection and Use of Hydraulic Cements, 6.9233R—Slag Cement in Concrete and Mortar, 5.11318—Building Code Requirements for Structural Concrete, 4.4325.10R—Report on Roller-Compacted Concrete Pavements, 9.2, 9.6330R—Guide for the Design and Construction of Concrete Parking Lots, 7.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 4.2350—Code Requirements for Environmental Engineering Concrete Structures, 4.2363R—Report on High-Strength Concrete, 5.12364.3R—Guide for Cementitious Repair Material Data Sheet, 5.11

522R—Pervious Concrete, 9.4523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.11523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.1.10544.1R—Report on Fiber-Reinforced Concrete, 3.5544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.7546.2R—Guide to Underwater Repair of Concrete, 2.6548.3R—Report on Polymer-Modified Concrete, Ch. 3, 3.6.1, 4.3555R—Removal and Reuse of Hardened Concrete, 5.4

Fresh concrete, see also Rheology212.3R—Chemical Admixtures for Concrete224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete308R—Guide to Curing Concrete309R—Guide for Consolidation of Concrete309.1R—Report on Behavior of Fresh Concrete During Vibration

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, Ch. 3

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 3, Ch. 4233R—Slag Cement in Concrete and Mortar, Ch. 4234R—Guide for the Use of Silica Fume in Concrete, Ch. 4304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 5

232.2R—Use of Fly Ash in Concrete, 3.1304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 7.7306R—Cold Weather Concreting, 4.1309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 2.4

Friction, see Skid resistance or Shear friction

Galleries in dams, see also Roller-compacted concrete or Mass concrete

207.5R—Roller-Compacted Mass Concrete, 4.6

Glass fibers, see also Fibers440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars

544.1R—Report on Fiber-Reinforced Concrete, Ch. 3

440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 4.3

440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement506.1R—Guide to Fiber-Reinforced Shotcrete, 3.2549.2R—Thin Reinforced Cementitious Products, 4.2

Glass units530—Building Code Requirements for Masonry Structures, Ch. 7

530.1—Specification for Masonry Structures, 2.3

Ground granulated blast-furnace slag (GGBFS)233R—Slag Cement in Concrete and Mortar

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 1, 5.7

207.1R—Guide to Mass Concrete, 2.3221.1R—Report on Alkali-Aggregate Reactivity, 5.7225R—Guide to the Selection and Use of Hydraulic Cements, 4.4234R—Guide for the Use of Silica Fume in Concrete, 3.8304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 2.4363R—Report on High-Strength Concrete, 2.4

Grout351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures


304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, Ch. 2 through Ch. 4, 5.1, 5.4

207.1R—Guide to Mass Concrete, 4.9222.2R—Corrosion of Prestressing Steels, 6.3224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.8232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 6.1232.2R—Use of Fly Ash in Concrete, 8.1233R—Slag Cement in Concrete and Mortar, 6.4238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 3.3.3, 5.2, 5.5301—Specifications for Structural Concrete, 5.3.7, 9.2.2304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 7.3, 7.6, 7.8304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 5.11318—Building Code Requirements for Structural Concrete, 18.18336.1—Specification for the Construction of Drilled Piers, 2.5351.2R—Foundations for Static Equipment, 5.6351.3R—Foundations for Dynamic Equipment, 5.6357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.12, 6.7371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 3.3.2, 3.3.3, 4.2.2372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.4503R—Use of Epoxy Compounds with Concrete, 4.5530—Building Code Requirements for Masonry Structures, 1.8.2.3530.1—Specification for Masonry Structures, 2.2, 3.5543R—Design, Manufacture, and Installation of Concrete Piles, 3.5546.2R—Guide to Underwater Repair of Concrete, 6.4548.3R—Report on Polymer-Modified Concrete, 4.3.7, 4.4.7.1ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 3.5, 5.8, 6.8T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 3.5, 3.6, 6.3

Guideways358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures

Handling concrete, see also Placing301—Specifications for Structural Concrete, Sec. 5523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, Ch. 7523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 5.1

ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 10, 17.6

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.3233R—Slag Cement in Concrete and Mortar, 2.2234R—Guide for the Use of Silica Fume in Concrete, 9.1303.1—Standard Specification for Cast-in-Place Architectural Concrete, 1.7318—Building Code Requirements for Structural Concrete, 16.9330.1—Specification for Unreinforced Concrete Parking Lots, 1.5350—Code Requirements for Environmental Engineering Concrete Structures, 16.9503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.4503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.4503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.14503.4—Standard Specification for Repairing Concrete with Epoxy Mortars, 2.1.4506.2—Specification for Shotcrete, 2.10506.5R—Guide for Specifying Underground Shotcrete, 12.1530.1—Specification for Masonry Structures, 1.7533R—Guide for Precast Concrete Wall Panels, 6.2543R—Design, Manufacture, and Installation of Concrete Piles, 4.7

Hardened concrete209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete555R—Removal and Reuse of Hardened Concrete

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, Ch. 4221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 2233R—Slag Cement in Concrete and Mortar, Ch. 5503.5R—Guide for the Selection of Polymer Adhesives with Concrete, Ch. 5

212.3R—Chemical Admixtures for Concrete, 3.4, 4.8, 5.7224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 1.3232.2R—Use of Fly Ash in Concrete, 3.2

Haunches, see Brackets

Hazardous material350.2R—Concrete Structures for Containment of Hazardous Materials

Health hazards, see Safety

Heat generation, see Heat of hydration

Heat of hydration, see also Curing 211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, App. 5, Ch. 4

MCP INDEX IND-31

207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 4.1207.4R—Cooling and Insulating Systems for Mass Concrete, 2.6213R—Guide for Structural Lightweight-Aggregate Concrete, 4.18233R—Slag Cement in Concrete and Mortar, 1.9234R—Guide for the Use of Silica Fume in Concrete, 3.10, 10.10304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 1.7308R—Guide to Curing Concrete, 1.3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 4.5.5.1363R—Report on High-Strength Concrete, 5.10503R—Use of Epoxy Compounds with Concrete, 3.9

Heavyweight concrete, see also High-density concrete

211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, App. 4304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing


304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 1.9

High-density concrete, see also Heavyweight concrete

309R—Guide for Consolidation of Concrete, Ch. 14

High-early-strength concrete, see also Admixtures

234R—Guide for the Use of Silica Fume in Concrete

318—Building Code Requirements for Structural Concrete, 5.11.2

High-performance concrete, see High-strength concrete

High-pressure steam curing, see Accelerated curing

High-range water-reducing admixtures, see also Admixtures

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete

High relative rib area, see Deformed bars

High-rise buildings212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.6308R—Guide to Curing Concrete, 3.2363R—Report on High-Strength Concrete, 7.3

High-strength concrete, see also Columns211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials363R—Report on High-Strength Concrete363.2R—Guide to Quality Control and Testing of High-Strength Concrete441R—High-Strength Concrete ColumnsITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications

213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 6234R—Guide for the Use of Silica Fume in Concrete, Ch. 5

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.2311.5—Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete, 2.5355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 8.4

High temperature, see also Fire resistance225R—Guide to the Selection and Use of Hydraulic Cements, 6.11

High-volume fly ash concrete232.2R—Use of Fly Ash in Concrete, 6.6

Highway bridge decks, see Bridge deck

Highway bridges, see Bridges (structures)

Historic structures364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, 3.2.2

Honeycombing, see Surface defects

Hooked reinforcement315—Details and Detailing of Concrete Reinforcement, 2.4318—Building Code Requirements for Structural Concrete, 7.1, 12.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 7.1, 12.5350—Code Requirements for Environmental Engineering Concrete Structures, 7.1

Hot weather concreting210R—Erosion of Concrete in Hydraulic Structures305R—Hot Weather Concreting305.1—Specification for Hot Weather ConcretingSP-15—Field Reference Manual


301—Specifications for Structural Concrete, 4.2.2.8, 5.3.2, 8.3.2.3304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 5.9, 7.3308R—Guide to Curing Concrete, 1.4, 2.5, 2.7308.1—Standard Specification for Curing Concrete, 1.8318—Building Code Requirements for Structural Concrete, 5.13330.1—Specification for Unreinforced Concrete Parking Lots, 3.12332—Code Requirements for Residential Concrete, 5.5332.1R—Guide to Residential Concrete Construction, 6.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.13350—Code Requirements for Environmental Engineering Concrete Structures, 5.12357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.4362.1R—Guide for the Design of Durable Parking Structures, 4.13506R—Guide to Shotcrete, 8.9506.2—Specification for Shotcrete, 3.9506.5R—Guide for Specifying Underground Shotcrete, 11.5522R—Pervious Concrete, 7.7522.1—Specification for Pervious Concrete Pavement, 3.11523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.8

Houses, see Residential concrete

Hydration, see Heat of hydration

Hydraulic cement grout, see also Grout351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery

Hydraulic cements, see also Cement225R—Guide to the Selection and Use of Hydraulic Cements

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 5

523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 2.2

Hydraulic design522R—Pervious Concrete, App. A

Hydraulic structures, see also Erosion210R—Erosion of Concrete in Hydraulic Structures

343R—Analysis and Design of Reinforced Concrete Bridge Structures, 11.4

Hydrogen222.2R—Corrosion of Prestressing Steels, Ch. 3

234R—Guide for the Use of Silica Fume in Concrete, 4.10

Hydrostatic350.1—Tightness Testing of Environmental Engineering Concrete Structures

350—Code Requirements for Environmental Engineering Concrete Structures, H.6

Impact, see also Loads506.1R—Guide to Fiber-Reinforced Shotcrete,7.7549R—Report on Ferrocement, 4.6

Implosion357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 4.5.1549R—Report on Ferrocement, 4.6

Inflated forms, see Forms – inflated

In-place testing, see Testing

Inspection, see also Testing201.1R—Guide for Conducting a Visual Inspection of Concrete in Service304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing311.1R—ACI Manual of Concrete Inspection311.4R—Guide for Concrete Inspection311.5—Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete350.1—Tightness Testing of Environmental Engineering Concrete Structures506.5R—Guide for Specifying Underground Shotcrete, Ch. 11533.1R—Design Responsibility for Architectural Precast-Concrete Projects550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 6

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, Ch. 2210R—Erosion of Concrete in Hydraulic Structures, Part 3304.4R—Placing Concrete with Belt Conveyors, Ch. 5305R—Hot Weather Concreting, Ch. 5309R—Guide for Consolidation of Concrete, Ch. 16325.10R—Report on Roller-Compacted Concrete Pavements, Ch. 8336.3R—Design and Construction of Drilled Piers, Ch. 5345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 3364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, Ch. 2522R—Pervious Concrete, Ch. 8546.2R—Guide to Underwater Repair of Concrete, Ch. 3, Ch. 7

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 5.2228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures, 2.1301—Specifications for Structural Concrete, 1.6, 9.3.1318—Building Code Requirements for Structural Concrete, 1.3330.1—Specification for Unreinforced Parking Lots, 1.6332—Code Requirements for Residential Concrete, 1.5336.1—Specification for the Construction of Drilled Piers, 3.7.6347—Guide to Formwork for Concrete, 3.6

MCP INDEX IND-33

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 1.3350—Code Requirements for Environmental Engineering Concrete Structures, 1.3350.2R—Concrete Structures for Containment of Hazardous Materials, 4.3, 5.4360R—Design of Slabs-on-Ground, 3.7440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 5.5440.1R—Guide for the Design and Construction of Concrete with FRP Bars, 6.3440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 7.1, 8.2503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3.7506R—Guide to Shotcrete, 9.7524R—Guide to Portland Cement-Based Plaster, 11.1530.1—Specification for Masonry Structures, 3.1

Installation, see also Placing440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 6530.1—Specification for Masonry Structures, Ch. 3533R—Guide for Precast Concrete Wall Panels, Ch. 6

Instrumentation, see also Testing357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 1.2

Insulating concretes308R—Guide to Curing Concrete, 3.4.7533R—Guide for Precast Concrete Wall Panels, 4.6

Insulation207.4R—Cooling and Insulating Systems for Mass Concrete

229R—Controlled Low-Strength Materials, 4.3.4306R—Cold Weather Concreting, 7.2, 7.3, 7.8551.1R—Tilt-Up Concrete Construction Guide, 5.7, 8.5

Iron233R—Slag Cement in Concrete and Mortar, 1.5

ISO, see also Quality assurance121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001

Isolation joints224R—Control of Cracking in Concrete Structures

224.3R—Joints in Concrete Construction, 3.4301—Specifications for Structural Concrete, 10.3302.1R—Guide for Concrete Floor and Slab Construction, 3.2.5.1318—Building Code Requirements for Structural Concrete, 22.3325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 4.4

330.1—Specification for Unreinforced Concrete Parking Lots, 2.4, 3.13530—Building Code Requirements for Masonry Structures, 1.14.5, 7.3.1

Joints, see also Isolation joints224.3R—Joints in Concrete Construction325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 3350.4R—Design Considerations for Environmental Engineering Concrete Structures, Ch. 5360R—Design of Slabs-on-Ground, Ch. 5ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 8

207.5R—Roller-Compacted Mass Concrete, 5.6301—Specifications for Structural Concrete, 5.3302.1R—Guide for Concrete Floor and Slab Construction, 3.2303R—Guide to Cast-in-Place Architectural Concrete Practice, 3.4304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 6.2, 7.9315—Details and Detailing of Concrete Reinforcement, 2.8, 2.10318—Building Code Requirements for Structural Concrete, 6.4, 22.3325.10R—Report on Roller-Compacted Concrete Pavements, 7.6330R—Guide for the Design and Construction of Concrete Parking Lots, 3.7, 3.9, 5.7, 7.3, C.1330.1—Specification for Unreinforced Concrete Parking Lots, 3.13332—Code Requirements for Residential Concrete, 8.5332.1R—Guide to Residential Concrete Construction, 5.5341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges, 4.3343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.20345.1R—Guide for Maintenance of Concrete Bridge Members, 3.3, 7.2, 7.5350—Code Requirements for Environmental Engineering Concrete Structures, 4.8, H.5372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 4.10373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.10506R—Guide to Shotcrete, 5.7506.2—Specification for Shotcrete, 3.4522.1—Specification for Pervious Concrete Pavement, 3.12548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks, 3.7548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks, 3.7551.1R—Tilt-Up Concrete Guide, 4.3, 8.3

Joints, connection349—Code Requirements for Nuclear Safety-Related Concrete Structures352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures


352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 5T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 4350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 3

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 6.2, 7.9315—Details and Detailing of Concrete Reinforcement, 2.10318—Building Code Requirements for Structural Concrete, 6.4325.10R—Report on Roller-Compacted Concrete Pavements, 7.6343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.20350—Code Requirements for Environmental Engineering Concrete Structures, 6.4, 21.5506R—Guide to Shotcrete, 5.7506.2—Specification for Shotcrete, 3.4530.1—Specification for Masonry Structures, 1.4, 2.4

Joints, junctions318—Building Code Requirements for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures350—Code Requirements for Environmental Engineering Concrete Structures352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures530—Building Code Requirements for Masonry Structures

Joints, movement224.3R—Joints in Concrete Construction

325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 4

207.5R—Roller-Compacted Mass Concrete, 5.6302.1R—Guide for Concrete Floor and Slab Construction, 3.2.5318—Building Code Requirements for Structural Concrete, 22.3325.11R—Accelerated Techniques for Concrete Paving, 5.3330R—Guide for the Design and Construction of Concrete Parking Lots, 3.7330.1—Specification for Unreinforced Concrete Parking Lots, 3.13350—Code Requirements for Environmental Engineering Concrete Structures, 6.5350.4R—Design Considerations for Environmental Engineering Concrete Structures, 5.3530—Building Code Requirements for Masonry Structures, 7.5

Joists318—Building Code Requirements for Structural Concrete, 8.13

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.11350—Code Requirements for Environmental Engineering Concrete Structures, 8.11

Lap splices, see Reinforcement

Lateral alignment, see Tolerances

Lateral-force-resisting system, see also Moment frame

374.1—Acceptance Criteria for Moment Frames Based on Structural TestingT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

318—Building Code Requirements for Structural Concrete, Ch. 21, 9.3.4349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 21350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 21

421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates, 2.1530—Building Code Requirements for Masonry Structures, 1.14

Latex, see also Adhesives503.5R—Guide for the Selection of Polymer Adhesives with Concrete503.6R—Guide for the Application of Epoxy and Latex Adhesives for Bonding Freshly Mixed and Hardened Concretes548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays

548.3R—Report on Polymer-Modified Concrete, Ch. 2, 5.2.1, 6.2.4

224R—Control of Cracking in Concrete Structures, 6.3

Latex-modified concrete, see also Overlays548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays

548.3R—Report on Polymer-Modified Concrete, Ch. 2, 5.1


Lath524R—Guide to Portland Cement-Based Plaster, Ch. 6, Ch. 8

Layer coefficients for pavements, see also Roller-compacted concrete

230.1R—Report on Soil Cement, 5.7

Layers, lines; see Surface defects

MCP INDEX IND-35

Leakage, see also Watertightness201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.14350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 7

Level alignment, see Tolerances

Lightweight aggregate, see also Aggregates211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, Ch. 2213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 2

Lightweight-aggregate concrete, see alsoLow-density concrete

211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete213R—Guide for Structural Lightweight-Aggregate Concrete435R—Control of Deflection in Concrete Structures

301—Specifications for Structural Concrete, Sec. 7304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 12309R—Guide for Consolidation of Concrete, Ch. 13

302.1R—Guide for Concrete Floor and Slab Construction, 8.11304.2R—Placing Concrete by Pumping Methods, 4.3349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.6350—Code Requirements for Environmental Engineering Concrete Structures, 11.2

Lining350.1—Tightness Testing of Environmental Engineering Concrete Structures

224.3R—Joints in Concrete Construction, Ch. 7350.2R—Concrete Structures for Containment of Hazardous Materials, Ch. 5

230.1R—Report on Soil Cement, 3.5313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.8350—Code Requirements for Environmental Engineering Concrete Structures, 4.7549.2R—Thin Reinforced Cementitious Products, 5.5

Liquid tightness, see Watertightness or Leakage

Load tests, see also Testing437.1R—Load Tests of Concrete Structures: Methods, Magnitude, Protocols, and Acceptance Criteria

318—Building Code Requirements for Structural Concrete, 20.3349—Code Requirements for Nuclear Safety-Related Concrete Structures, 20.3, 20.4350—Code Requirements for Environmental Engineering Concrete Structures, 20.3

437R—Strength Evaluation of Existing Concrete Buildings, 5.2

Loads408.2R—Bond under Cyclic Loads

307—Code Requirements for Reinforced Concrete Chimneys, Ch. 4318—Building Code Requirements for Structural Concrete, Ch. 20, 8.2336.3R—Design and Construction of Drilled Piers, Ch. 3343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 5, Ch. 8349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 8350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 4, Ch. 5350.4R—Design Considerations for Environmental Engineering Concrete Structures, Ch. 2357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, Ch. 3, App. A357.2R—Report on Barge-Like Concrete Structures, Ch. 4358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, Ch. 3, Ch. 4360R—Design of Slabs-on-Ground, Ch. 4437R—Strength Evaluation of Existing Concrete Buildings, Ch. 4ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 4

224R—Control of Cracking in Concrete Structures, 5.2313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 4.4, 7.3325.10R—Report on Roller-Compacted Concrete Pavements, 9.7336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, 1.4347—Guide to Formwork for Concrete, 2.2350—Code Requirements for Environmental Engineering Concrete Structures, 8.2, 8.9, 15.2, 18.11, 20.3351.2R—Foundations for Static Equipment, 3.1351.3R—Foundations for Dynamic Equipment, 3.2365.1R—Service-Life Prediction, 2.3371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 5, 5.1.2, 6.3, 6.4, 6.5, 7.4.3.1, 7.8.1.2, 7.8.3.1, App. 5435R—Control of Deflection in Concrete Structures, 4.6530—Building Code Requirements for Masonry Structures, 1.7543R—Design, Manufacture, and Installation of Concrete Piles, 2.2549R—Report on Ferrocement, 4.2 through 4.5

Low-density concrete, see also Lightweight aggregate concrete or Cellular concrete

523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units



Low-density material229R—Controlled Low-Strength Materials, Ch. 8

Low-strength concrete355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 8.3

Low-strength materials, see Controlledlow-strength materials

Machinery foundations, see Foundations and Footings

Maintenance345.1R—Guide for Maintenance of Concrete Bridge Members362.2R—Guide for Structural Maintenance of Parking Structures

330R—Guide for the Design and Construction of Concrete Parking Lots, Ch. 7357.2R—Report on Barge-Like Concrete Structures, Ch. 8362.1R—Guide for the Design of Durable Parking Structures, Ch. 5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 8548.5R—Guide for Polymer Concrete Overlays, Ch. 7549.1R—Guide for the Design, Construction, and Repair of Ferrocement, Ch. 6

304.4R—Placing Concrete with Belt Conveyors, 4.5345R—Guide for Concrete Highway Bridge Deck Construction, 12.3365.1R—Service-Life Prediction, 3.4

Manufacturing440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 4.8523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 3.2548.3R—Report on Polymer-Modified Concrete, 4.4.2

Marine concrete, see also Underwater repair357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures357.2R—Report on Barge-Like Concrete Structures546.2R—Guide to Underwater Repair of Concrete


201.2R—Guide to Durable Concrete, 6.4503R—Use of Epoxy Compounds with Concrete, 4.8, 7.3

Masonry530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, Ch. 3, Ch. 4

440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 10

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 5.1232.2R—Use of Fly Ash in Concrete, 7.1524R—Guide to Portland Cement-Based Plaster, 9.3, 9.4

Masonry cements, see also Cement530—Building Code Requirements for Masonry Structures

Masonry mortars, see also Grout530—Building Code Requirements for Masonry Structures

Masonry units, see Masonry

Masonry walls122R—Guide to Thermal Properties of Concrete and Masonry Systems, Ch. 3, Ch. 4216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, Ch. 3, Ch. 4

530—Building Code Requirements for Masonry Structures, 1.9, 2.1, 5.3, 5.6-5.8

Mass concrete, see also Roller-compacted concrete

207.1R—Guide to Mass Concrete207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions207.4R—Cooling and Insulating Systems for Mass Concrete207.5R—Roller-Compacted Mass Concrete

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 8211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, App. 5224R—Control of Cracking in Concrete Structures, Ch. 7301—Specifications for Structural Concrete, Sec. 8309R—Guide for Consolidation of Concrete, Ch. 9

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 5.4232.2R—Use of Fly Ash in Concrete, 6.3233R—Slag Cement in Concrete and Mortar, 5.7304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 5.6308R—Guide to Curing Concrete, 3.3347—Guide to Formwork for Concrete, 6.5555R—Removal and Reuse of Hardened Concrete, 2.4

Massive concrete212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.8

Material response209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 2

MCP INDEX IND-37

Materials, see also Material response126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database301—Specifications for Structural Concrete304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete364.3R—Guide for Cementitious Repair Material Data Sheet439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities503.5R—Guide for the Selection of Polymer Adhesives with Concrete506.5R—Guide for Specifying Underground Shotcrete, Ch. 4523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, Ch. 3546.3R—Guide for the Selection of Materials for the Repair of ConcreteITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications

207.1R—Guide to Mass Concrete, Ch. 2207.5R—Roller-Compacted Mass Concrete, Ch. 2211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, Ch. 4211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, Ch. 4211.5R—Guide for Submittal of Concrete Proportions, Ch. 2213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 2224.3R—Joints in Concrete Construction, Ch. 2229R—Controlled Low-Strength Materials, Ch. 3303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 6306R—Cold Weather Concreting, Ch. 7306.1—Standard Specification for Cold Weather Concreting, Ch. 2307—Code Requirements for Reinforced Concrete Chimneys, Ch. 2308R—Guide to Curing Concrete, Ch. 2313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, Ch. 2318—Building Code Requirements for Structural Concrete, Ch. 3325.11R—Accelerated Techniques for Concrete Paving, Ch. 4325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 2330R—Guide for the Design and Construction of Concrete Parking Lots, Ch. 4332—Code Requirements for Residential Concrete, Ch. 3343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 3345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 7347—Guide to Formwork for Concrete, Ch. 4349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 3350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 3351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, Ch. 3362.1R—Guide for the Design of Durable Parking Structures, Ch. 3363R—Report on High-Strength Concrete, Ch. 2

371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 3372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, Ch. 3423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, Ch. 4440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 3, Ch. 5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 4440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, Ch. 6506R—Guide to Shotcrete, Ch. 2506.2—Specification for Shotcrete, Ch. 2522R—Pervious Concrete, Ch. 3523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, Ch. 2530.1—Specification for Masonry Structures, Ch. 2533R—Guide for Precast Concrete Wall Panels, Ch. 4544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, Ch. 4546R—Concrete Repair Guide, Ch. 3ITG-3—Report on Bridge Decks Free of Steel Reinforcement, Ch. 4ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 2

237R—Self-Consolidating Concrete, 4.3, 7.1308R—Guide to Curing Concrete, 2.3308.1—Standard Specification for Curing Concrete, 2.2332.1R—Guide to Residential Concrete Construction, 2.2, 6.4346—Specification for Cast-in-Place Concrete Pipe, 2.1351.2R—Foundations for Static Equipment, 5.7351.3R—Foundations for Dynamic Equipment, 5.7435R—Control of Deflection in Concrete Structures, 2.3, 5.4440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 1.5, 2.1503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2

Materials handling304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 2440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 5548.1R—Guide for the Use of Polymers in Concrete, Ch. 5

423.7—Specification for Unbonded Single-Strand Tendon Materials, 1.7440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 6.1440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 1.5506.2—Specification for Shotcrete, 2.10506.5R—Guide for Specifying Underground Shotcrete, Ch. 6530.1—Specification for Masonry Structures, 1.7


Materials property database126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database

Mats, see also Foundations and Footings336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats

318—Building Code Requirements for Structural Concrete, 15.10349—Code Requirements for Nuclear Safety-Related Concrete Structures, 15.10350—Code Requirements for Environmental Engineering Concrete Structures, 15.10

Measuring, see also Mixture proportioning304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 3345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 8

Mechanical properties, see Properties of concrete

Mechanical splices, see Couplers

Membranes, see also Protective coatings350.1—Tightness Testing of Environmental Engineering Concrete Structures

362.1R—Guide for the Design of Durable Parking Structures, 4.11

Metal fibers544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete544.4R—Design Considerations for Steel Fiber-Reinforced Concrete

506.1R—Guide to Fiber-Reinforced Shotcrete, 3.2544.1R—Report on Fiber-Reinforced Concrete, Ch. 2

Metals, see Corrosion

Mineral admixtures, see also Admixtures126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 8

225R—Guide to the Selection and Use of Hydraulic Cements, 4.3363R—Report on High-Strength Concrete, 2.4

Mixers, see also Equipment304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 4

304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 3.2304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 3.2

Mixing304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 4304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Ch. 3318—Building Code Requirements for Structural Concrete, Ch. 5350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 5524R—Guide to Portland Cement-Based Plaster, Ch. 10

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 4.5207.1R—Guide to Mass Concrete, 4.2211.3R—Guide for Selecting Proportions for No-Slump Concrete, 2.3213R—Guide for Structural Lightweight-Aggregate Concrete, 3.5222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 4.1229R—Controlled Low-Strength Materials, 6.2230.1R—Report on Soil Cement, 7.2, 8.5238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.7, 5.2.2.4301—Specifications for Structural Concrete, 4.3.1, 7.2.4302.1R—Guide for Concrete Floor and Slab Construction, 7.2304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 3.2305R—Hot Weather Concreting, 3.3306R—Cold Weather Concreting, 3.2, 3.3325.10R—Report on Roller-Compacted Concrete Pavements, 7.3330.1—Specification for Unreinforced Concrete Parking Lots, 3.5345R—Guide for Concrete Highway Bridge Deck Construction, 8.4 through 8.6346—Specification for Cast-in-Place Concrete Pipe, 1.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.8351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 7.3363R—Report on High-Strength Concrete, 4.3503R—Use of Epoxy Compounds with Concrete, 7.2503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3.8506R—Guide to Shotcrete, 7.3506.1R—Guide to Fiber-Reinforced Shotcrete, 5.2506.2—Specification for Shotcrete, 3.2506.5R—Guide for Specifying Underground Shotcrete, Ch. 12523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.3530.1—Specification for Masonry Structures, 2.6533R—Guide for Precast Concrete Wall Panels, 5.3543R—Design, Manufacture, and Installation of Concrete Piles, 4.5544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 6.2

MCP INDEX IND-39

Mixture proportioning, see also Batching211.5R—Guide for Submittal of Concrete Proportions 212.3R—Chemical Admixtures for Concrete

207.5R—Roller-Compacted Mass Concrete, Ch. 2, 5.3211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, Ch. 6211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, Ch. 3211.3R—Guide for Selecting Proportions for No-Slump Concrete, App. 3 through 6, Ch. 4211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, Ch. 4, Ch. 6 through 8223—Standard Practice for the Use of Shrinkage-Compensating Concrete, Ch. 4229R—Controlled Low-Strength Materials, Ch. 5230.1R—Report on Soil Cement, Ch. 6232.2R—Use of Fly Ash in Concrete, Ch. 4233R—Slag Cement in Concrete and Mortar, Ch. 3234R—Guide for the Use of Silica Fume in Concrete, Ch. 8237R—Self-Consolidating Concrete, Ch. 4301—Specifications for Structural Concrete, Sec. 4303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 6304.2R—Placing Concrete by Pumping Methods, Ch. 4304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Ch. 2304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Ch. 4309R—Guide for Consolidation of Concrete, Ch. 2363R—Report on High-Strength Concrete, Ch. 3506.1R—Guide to Fiber-Reinforced Shotcrete, Ch. 4522R—Pervious Concrete, Ch. 5524R—Guide to Portland Cement-Based Plaster, Ch. 10544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, Ch. 4, Ch. 6ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 3ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 6, 17.2

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 4.4207.1R—Guide to Mass Concrete, 2.7213R—Guide for Structural Lightweight-Aggregate Concrete, 3.2, 3.4221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.2222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 3.1, 3.2232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 2.1302.1R—Guide for Concrete Floor and Slab Construction, 6.2, 6.3304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 7.3, 8.3, 9.4304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.8, 5.1304.4R—Placing Concrete with Belt Conveyors, 2.6305R—Hot Weather Concreting, 2.9305.1—Specification for Hot Weather Concreting, 2.2, 3.3

309.1R—Report on Behavior of Fresh Concrete During Vibration, 3.2.1318—Building Code Requirements for Structural Concrete, 5.2 through 5.4325.10R—Report on Roller-Compacted Concrete Pavements, 4.2, 4.3325.11R—Accelerated Techniques for Concrete Paving, 4.1325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2332.1R—Guide to Residential Concrete Construction, 2.3349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.2 through 5.4350—Code Requirements for Environmental Engineering Concrete Structures, 5.2, 5.3350.2R—Concrete Structures for Containment of Hazardous Materials, 2.5503R—Use of Epoxy Compounds with Concrete, 6.3506R—Guide to Shotcrete, 6.3506.1R—Guide to Fiber-Reinforced Shotcrete, Ch. 4, 5.2506.2—Specification for Shotcrete, 2.7506.5R—Guide for Specifying Underground Shotcrete, Ch. 7523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 4.1533R—Guide for Precast Concrete Wall Panels, 5.3548.1R—Guide for the Use of Polymers in Concrete, 5.4548.3R—Report Polymer-Modified Concrete, 4.1.2, 4.3.4, 4.4.4549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 3.1, 3.15549R—Report on Ferrocement, 3.5555R—Removal and Reuse of Hardened Concrete, 5.5

Modeling, see also Finite element analysis209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete446.1R—Fracture Mechanics of Concrete: Concepts, Models, and Determination of Material Properties446.4R—Report on Dynamic Fracture of Concrete

334.1R—Concrete Shell Structures Practice, Ch. 8341.2R—Seismic Analysis and Design of Concrete Bridge Systems, Ch. 4350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 9446.3R—Finite Element Analysis of Fracture in Concrete Structures, Ch. 2, Ch. 3

Modified compression field theory, see also Shear strength

445R—Recent Approaches to Shear Design of Structural Concrete, 2.4, 2.6

Modulus of elasticity, see also Properties of concrete

207.1R—Guide to Mass Concrete, 3.3207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.6212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.2213R—Guide for Structural Lightweight-Aggregate Concrete, 4.6, 5.3


221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 2.6233R—Slag Cement in Concrete and Mortar, 5.3318—Building Code Requirements for Structural Concrete, 8.5325.10R—Report on Roller-Compacted Concrete Pavements, 5.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.5350—Code Requirements for Environmental Engineering Concrete Structures, 8.5363R—Report on High-Strength Concrete, 5.3364.3R—Guide for Cementitious Repair Material Data Sheet, 5.7

440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 5.1523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.6523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.1.2.1530—Building Code Requirements for Masonry Structures, 1.8555R—Removal and Reuse of Hardened Concrete, 5.4

Modulus of rupture, see also Properties of concrete

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.11233R—Slag Cement in Concrete and Mortar, 5.2363R—Report on High-Strength Concrete, 5.5523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.1.3.4

Modulus of subgrade reaction, see also Base360R—Design of Slabs-on-Ground, 3.4

Moisture content302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials

308.1—Standard Specification for Curing Concrete, Ch. 2, Ch. 3

207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 4.2211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, 6.3, 7.3230.1R—Report on Soil Cement, 4.7, 5.2, 8.4304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 4.4, 7.4308R—Guide to Curing Concrete, 1.3, 2.4, 4.5, 4.7309.5R—Compaction of Roller-Compacted Concrete, 2.2, 6.2332.1R—Guide to Residential Concrete Construction, 4.7530—Building Code Requirements for Masonry Structures, 1.8

Moment frame, see also Lateral-force resisting system

374.1—Acceptance Criteria for Moment Frames Based on Structural TestingT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 21.3

Monolithic joints, see Beam-column joints

Mortars, see also Masonry mortars503.4—Standard Specification for Repairing Concrete with Epoxy Mortars

234R—Guide for the Use of Silica Fume in Concrete, Ch. 3

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 6.1232.2R—Use of Fly Ash in Concrete, 8.1233R—Slag Cement in Concrete and Mortar, 6.4503R—Use of Epoxy Compounds with Concrete, 4.7548.3R—Report on Polymer-Modified Concrete, Ch. 4, 4.1.3.2, 4.1.3.3, 4.2.3.2, 4.4.5, 4.4.6, 4.4.7.3

Natural pozzolans, see Pozzolans

Navigation lock210R—Erosion of Concrete in Hydraulic Structures, 3.3

Nondestructive evaluation (NDE), see also Testing or Evaluation

228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures555R—Removal and Reuse of Hardened Concrete

325.11R—Accelerated Techniques for Concrete Paving, Ch. 6440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 5

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 3.9423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 4.4437R—Strength Evaluation of Existing Concrete Buildings, 2.2, 3.1506.4R—Guide for the Evaluation of Shotcrete, 2.3546.2R—Guide to Underwater Repair of Concrete, 3.4

No-slump concrete, see also Slump211.3R—Guide for Selecting Proportions for No-Slump Concrete

Notation, see also Terminology318—Building Code Requirements for Structural Concrete, Ch. 2

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, 1.5

Nozzlemen, see also Shotcrete506.5R—Guide for Specifying Underground Shotcrete506R—Guide to Shotcrete, 9.5506.2—Specification for Shotcrete, 1.6.1

Nuclear radiation shielding304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Ch. 1

MCP INDEX IND-41

Nuclear safety-related structures349—Code Requirements for Nuclear Safety-Related Concrete Structures349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures359—Code for Concrete Containments

229R—Controlled Low-Strength Materials, 2.9

Offsets, see Tolerances

Offshore structures357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures

One-way slabs, see Slabs

Openings, see also Tolerances307—Code Requirements for Reinforced Concrete Chimneys, Ch. 4, 3.8, 3.8.2, 4.1.3, 5.5.3, 5.5.4313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 6.10318—Building Code Requirements for Structural Concrete, 13.4330R—Guide for the Design and Construction of Concrete Parking Lots, 5.9349—Code Requirements for Nuclear Safety-Related Concrete Structures, 13.4352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 4.4423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.3551.1R—Tilt-Up Concrete Construction Guide, 4.3

OrderingITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 6ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 9, 17.5

Oscillation350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 7

Outlets207.5R—Roller-Compacted Mass Concrete, 4.9

Overlays, see also Latex-modified concrete325.13—Concrete Overlays for Pavement Rehabilitation548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays548.5R—Guide for Polymer Concrete Overlays548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks

548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks

224R—Control of Cracking in Concrete Structures, Ch. 6330R—Guide for the Design and Construction of Concrete Parking Lots, 7.6345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 13

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.12548.3R—Report on Polymer-Modified Concrete, 4.3, 4.3.4

Paints, see also Coatings308R—Guide to Curing Concrete, 3.4551.1R—Tilt-Up Concrete Construction Guide, 8.4

Panels, see also Walls523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels533R—Guide for Precast Concrete Wall Panels533.1R—Design Responsibility for Architectural Precast-Concrete Projects

530—Building Code Requirements for Masonry Structures, Ch. 7

549.2R—Thin Reinforced Cementitious Products, 5.1, 5.2, 5.3, 5.7

Parking lots, see also Slab-on-ground330R—Guide for the Design and Construction of Concrete Parking Lots330.1—Specification for Unreinforced Concrete Parking Lots522R—Pervious Concrete

224.3R—Joints in Concrete Construction, 6.6

Parking structures362.1R—Guide for the Design of Durable Parking Structures362.2R—Guide for Structural Maintenance of Parking Structures548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks

212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.5

Pavements229R—Controlled Low-Strength Materials325.10R—Report on Roller-Compacted Concrete Pavements325.11R—Accelerated Techniques for Concrete Paving325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads330R—Guide for the Design and Construction of Concrete Parking Lots522.1—Specification for Pervious Concrete Pavement544.1R—Report on Fiber-Reinforced Concrete




201.2R—Guide to Durable Concrete, 8.5, 8.6230.1R—Report on Soil Cement, 3.2232.2R—Use of Fly Ash in Concrete, 6.2308R—Guide to Curing Concrete, 3.1309.5R—Compaction of Roller-Compacted Concrete, 5.4330.1—Specification for Unreinforced Concrete Parking Lots, 3.6, 3.7440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 6.7555R—Removal and Reuse of Hardened Concrete, 4.6

Permeability, see also Properties of concrete506.4R—Guide for the Evaluation of Shotcrete, Ch. 5

207.1R—Guide to Mass Concrete, 3.6207.5R—Roller-Compacted Mass Concrete, 3.9230.1R—Report on Soil Cement, 5.5233R—Slag Cement in Concrete and Mortar, 5.8523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.10555R—Removal and Reuse of Hardened Concrete, 5.4

Pervious concrete522R—Pervious Concrete522.1—Specification for Pervious Concrete Pavement

Petrographic examination201.2R—Guide to Durable Concrete207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete221.1R—Report on Alkali-Aggregate Reactivity349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures437R—Strength Evaluation of Existing Concrete Buildings555R—Removal and Reuse of Hardened Concrete

Photographs303R—Guide to Cast-in-Place Architectural Concrete Practice, App. A

Physical properties, see also Modulus of elasticity

213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 4225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 5233R—Slag Cement in Concrete and Mortar, Ch. 3234R—Guide for the Use of Silica Fume in Concrete, Ch. 2

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 1.6232.2R—Use of Fly Ash in Concrete, 2.5308R—Guide to Curing Concrete, 4.7364.3R—Guide for Cementitious Repair Material Data Sheet

440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 3.1440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.2440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, Ch. 7

Piers, see also Drilled piers343R—Analysis and Design of Reinforced Concrete Bridge Structures, 11.6

Piles, see also Drilled piers543R—Design, Manufacture, and Installation of Concrete Piles

117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 3440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 8

304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 5.11351.2R—Foundations for Static Equipment, 4.6

Pipe bedding229R—Controlled Low-Strength Materials, 2.6

Pipe diameter, see Tolerances

Pipes346—Specification for Cast-in-Place Concrete Pipe


224.3R—Joints in Concrete Construction, 7.4232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 5.2232.2R—Use of Fly Ash in Concrete, 7.2350—Code Requirements for Environmental Engineering Concrete Structures, 6.3371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 7.6, 7.7

Placeability, see Workability

Placing concrete304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications304.2R—Placing Concrete by Pumping Methods304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing304.4R—Placing Concrete with Belt Conveyors309R—Guide for Consolidation of Concrete506.1R—Guide to Fiber-Reinforced Shotcrete

237R—Self-Consolidating Concrete, Ch. 6, 6.5

MCP INDEX IND-43

301—Specifications for Structural Concrete, Sec. 5, 8.3, 9.3, 10.3302.1R—Guide for Concrete Floor and Slab Construction, Ch. 8303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 7305R—Hot Weather Concreting, Ch. 4309.5R—Compaction of Roller-Compacted Concrete, Ch. 5332—Code Requirements for Residential Concrete, Ch. 5345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 9350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 5351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, Ch. 7544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.2ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 9ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 13, 8.3, 17.9

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 11.8201.2R—Guide to Durable Concrete, 3.4207.1R—Guide to Mass Concrete, 4.3207.4R—Cooling and Insulating Systems for Mass Concrete, 2.8207.5R—Roller-Compacted Mass Concrete, 5.4212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 6.4213R—Guide for Structural Lightweight-Aggregate Concrete, 3.6222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 4.2223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 5.1229R—Controlled Low-Strength Materials, 6.4234R—Guide for the Use of Silica Fume in Concrete, 9.4306R—Cold Weather Concreting, 3.1, 7.6307—Code Requirements for Reinforced Concrete Chimneys, 3.6309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 2.5313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.6318—Building Code Requirements for Structural Concrete, 5.10325.10R—Report on Roller-Compacted Concrete Pavements, 7.4330R—Guide for the Design and Construction of Concrete Parking Lots, 5.5330.1—Specification for Unreinforced Concrete Parking Lots, 3.6, 3.7332.1R—Guide to Residential Concrete Construction, 3.11, 5.4, 6.3334.1R—Concrete Shell Structures Practice, 7.2336.3R—Design and Construction of Drilled Piers, 5.5346—Specification for Cast-in-Place Concrete Pipe, 3.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 5.10362.1R—Guide for the Design of Durable Parking Structures, 4.6363R—Report on High-Strength Concrete, 4.5363.2R—Guide to Quality Control and Testing of High-Strength Concrete, 3.4423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.4

440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 3.5506R—Guide to Shotcrete, 9.6506.2—Specification for Shotcrete, 3.6506.5R—Guide for Specifying Underground Shotcrete, Ch. 13522.1—Specification for Pervious Concrete Pavement, 3.5, 3.6523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.4533R—Guide for Precast Concrete Wall Panels, 5.5543R—Design, Manufacture, and Installation of Concrete Piles, 5.5

Placing drawings315—Details and Detailing of Concrete Reinforcement, Ch. 3

Placing equipment, see also Equipment304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 4.2, 8.5, 9.2, 11.4

Plain concrete330.1—Specification for Unreinforced Concrete Parking LotsITG-3—Report on Bridge Decks Free of Steel Reinforcement


446.3R—Finite Element Analysis of Fracture in Concrete Structures, 4.2

Plans, see Specifications

Plastering524R—Guide to Portland Cement-Based Plaster

308R—Guide to Curing Concrete, 3.4

Plastic concrete, see also Rheology, Consolidation, Placing, or Admixtures

503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive

503.5R—Guide for the Selection of Polymer Adhesives with Concrete, Ch. 6

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 1.2533R—Guide for Precast Concrete Wall Panels, 7.6

Plastic properties, see Properties

Plastic shotcrete506.4R—Guide for the Evaluation of Shotcrete, Ch. 6

Plastic shrinkage, see also Cracks305R—Hot Weather Concreting, Ch. 2

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 1.2


234R—Guide for the Use of Silica Fume in Concrete, 4.6308R—Guide to Curing Concrete, 3.1

Plastics in concrete, see also Polymer concrete503R—Use of Epoxy Compounds with Concrete503.5R—Guide for the Selection of Polymer Adhesives with Concrete548.3R—Report on Polymer-Modified Concrete

Pneumatic350.1—Tightness Testing of Environmental Engineering Concrete Structures

Pneumatically applied concrete, see Shotcrete

Poisson’s ratio, see also Properties of concrete213R—Guide for Structural Lightweight-Aggregate Concrete, 4.7228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures, 2.2363R—Report on High-Strength Concrete, 5.4

Polymer adhesives, see also Adhesive or Epoxy adhesive

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete503.5R—Guide for the Selection of Polymer Adhesives with Concrete

Polymer concrete440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete440.4R—Prestressing Concrete Structures with FRP Tendons548.1R—Guide for the Use of Polymers in Concrete548.3R—Report on Polymer-Modified Concrete548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays548.5R—Guide for Polymer Concrete Overlays548.7—Test Method for Load Capacity of Polymer Concrete Underground Utility Structures

224R—Control of Cracking in Concrete Structures, 5.5546R—Concrete Repair Guide, 3.3

Polymer-impregnated concrete548.1R—Guide for the Use of Polymers in Concrete, Ch. 3

224R—Control of Cracking in Concrete Structures, 6.4224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.11

Polymer-portland cement concrete, see Polymer concrete

Polymer reinforcement, see Fiber-reinforced polymer

Polymerization548.3R—Report on Polymer-Modified Concrete, 1.1, 4.2.2.1, 4.3.2.2

548.1R—Guide for the Use of Polymers in Concrete, 3.5

Popouts, see also Surface defects201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.18221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 2.1302.1R—Guide for Concrete Floor and Slab Construction, 11.6

Portland cement, see Cement

Post-tensioning, see also Prestressed concrete222.2R—Corrosion of Prestressing Steels374.1—Acceptance Criteria for Moment Frames Based on Structural Testing423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons423.7—Specification for Unbonded Single-Strand Tendon MaterialsITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation TestingITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1

T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members


223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 3.5, 3.6313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 6.3, 6.7, 6.13318—Building Code Requirements for Structural Concrete, 18.13, 18.21347.2R—Guide for Shoring/Reshoring of Concrete Multistory Buildings, 5.2350—Code Requirements for Environmental Engineering Concrete Structures, 18.13, 18.17, 18.21, 18.22546R—Concrete Repair Guide, 5.5555R—Removal and Reuse of Hardened Concrete, 2.4

Pouring, see Placing concrete

Pozzolans, see also Cementitious materials234R—Guide for the Use of Silica Fume in Concrete

207.1R—Guide to Mass Concrete, 2.3

MCP INDEX IND-45

221.1R—Report on Alkali-Aggregate Reactivity, 9.4304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 2.4

Precast concrete374.1—Acceptance Criteria for Moment Frames Based on Structural Testing523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units533R—Guide for Precast Concrete Wall Panels533.1R—Design Responsibility for Architectural Precast-Concrete Projects550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete StructuresITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation TestingITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1ITG-7—Specification for Tolerances for Precast Concrete


232.2R—Use of Fly Ash in Concrete, Ch. 7309R—Guide for Consolidation of Concrete, Ch. 12318—Building Code Requirements for Structural Concrete, Ch. 16343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 9, Ch. 12349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 16350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 16

209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 4.3304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 5.8307—Code Requirements for Reinforced Concrete Chimneys, 3.9308R—Guide to Curing Concrete, 3.4.1313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 2.7347—Guide to Formwork for Concrete, 7.7362.2R—Guide for Structural Maintenance of Parking Structures, 4.5546.2R—Guide to Underwater Repair of Concrete, 8.1ITG-3—Report on Bridge Decks Free of Steel Reinforcement, 8.5

Preconstruction planning551.1R—Tilt-Up Concrete Construction Guide, Ch. 2ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 5ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 8, 17.4

311.4R—Guide for Concrete Inspection, 3.4

Prediction, see also Service life209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures

209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, Ch. 3

365.1R—Service-Life Prediction, 4.4

Preformed foam, see also Cellular concrete229R—Controlled Low-Strength Materials, Ch. 8

523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 2.3

Preparation, see Surface preparation506.5R—Guide for Specifying Underground Shotcrete, Ch. 16

Preplaced aggregate concrete, see also Aggregates, preplaced

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing

309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, Ch. 5

347—Guide to Formwork for Concrete, 7.2546.2R—Guide to Underwater Repair of Concrete, 6.2

Pressures, see also Loads350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 8, 4.1

304.2R—Placing Concrete by Pumping Methods, 3.2336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, 1.5

Prestressed concrete, see also Post-tensioning212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete222.2R—Corrosion of Prestressing Steels232.2R—Use of Fly Ash in Concrete358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons374.1—Acceptance Criteria for Moment Frames Based on Structural Testing423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons423.7—Specification for Unbonded Single-Strand Tendon MaterialsT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete MembersITG-7—Specification for Tolerances for Precast Concrete

209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 4


301—Specifications for Structural Concrete, Sec. 9318—Building Code Requirements for Structural Concrete, Ch. 18343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 9349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 18350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 18, App. B, App. G421.1R—Guide to Shear Reinforcement for Slabs, Ch. 5435R—Control of Deflection in Concrete Structures, Ch. 3440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 7440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 7

213R—Guide for Structural Lightweight-Aggregate Concrete, 5.9224R—Control of Cracking in Concrete Structures, 4.6232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 5.3334.1R—Concrete Shell Structures Practice, 4.4347—Guide to Formwork for Concrete, 7.5362.2R—Guide for Structural Maintenance of Parking Structures, 4.5533R—Guide for Precast Concrete Wall Panels, 7.4555R—Removal and Reuse of Hardened Concrete, 2.4

Prestressed masonry530—Building Code Requirements for Masonry Structures, Ch. 4

530.1—Specification for Masonry Structures, 2.4, 3.6

Prestressing steel222R—Protection of Metals in Concrete Against Corrosion222.2R—Corrosion of Prestressing Steels423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons

301—Specifications for Structural Concrete, Sec. 9318—Building Code Requirements for Structural Concrete, Ch. 18343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 9350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 18, 12.9439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities, Ch. 6530—Building Code Requirements for Masonry Structures, Ch. 4

349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures, 4.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.10423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.1T1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members, 3.4

Pretensioned222.2R—Corrosion of Prestressing Steels, 5.3, 7.3555R—Removal and Reuse of Hardened Concrete, 2.4

Problems, see Repair

Production304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, Ch. 4237R—Self-Consolidating Concrete, Ch. 5305R—Hot Weather Concreting, Ch. 3332—Code Requirements for Residential Concrete, Ch. 5555R—Removal and Reuse of Hardened Concrete, Ch. 5ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 7ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 11, 17.7

213R—Guide for Structural Lightweight-Aggregate Concrete, 2.2304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 4.2, Ch. 5, Ch. 6305.1—Specification for Hot Weather Concreting, 3.4309R—Guide for Consolidation of Concrete, 12.4

Properties of concrete122R—Guide to Thermal Properties of Concrete and Masonry Systems126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database214R—Evaluation of Strength Test Results of Concrete233R—Slag Cement in Concrete and Mortar234R—Guide for the Use of Silica Fume in Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing555R—Removal and Reuse of Hardened Concrete

207.1R—Guide to Mass Concrete, Ch. 3207.5R—Roller-Compacted Mass Concrete, Ch. 3213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 4229R—Controlled Low-Strength Materials, Ch. 4237R—Self-Consolidating Concrete, Ch. 2, Ch. 3363R—Report on High-Strength Concrete, Ch. 5440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 5440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, Ch.8522R—Pervious Concrete, Ch. 4523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, Ch. 3, 4.4523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.1546.3R—Guide for the Selection of Materials for the Repair of Concrete, Ch. 2ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 4

212.3R—Chemical Admixtures for Concrete, 2.3232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 2.2, 2.3302.1R—Guide for Concrete Floor and Slab Construction, 6.1

MCP INDEX IND-47

302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, 6.7, 9.5308R—Guide to Curing Concrete, 1.6325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2345R—Guide for Concrete Highway Bridge Deck Construction, 7.3350—Code Requirements for Environmental Engineering Concrete Structures, 20.2408R—Bond and Development of Straight Reinforcing Bars in Tension, 2.3, 6.2548.3R—Report on Polymer-Modified Concrete, 3.1, 4.1.3, 4.2.2, 4.2.3, 4.4.5, 4.4.6,

Proportioning, see Mixture proportioning

Protection during concrete construction423.7—Specification for Unbonded Single-Strand Tendon Materials

222R—Protection of Metals in Concrete Against Corrosion, Ch. 3222.2R—Corrosion of Prestressing Steels, Ch. 4306R—Cold Weather Concreting, Ch. 5, Ch. 6350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 4, 7.7

201.2R—Guide to Durable Concrete, 7.5.5207.5R—Roller-Compacted Mass Concrete, 5.9301—Specifications for Structural Concrete, 1.8, 5.3, 8.3305R—Hot Weather Concreting, 4.4306.1—Standard Specification for Cold Weather Concreting, 3.4308R—Guide to Curing Concrete, 2.6, 2.7313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.7318—Building Code Requirements for Structural Concrete, 7.7, 18.16, 18.19325.10R—Report on Roller-Compacted Concrete Pavements, 7.7330R—Guide for the Design and Construction of Concrete Parking Lots, 5.6343R—Analysis and Design of Reinforced Concrete Bridge Structures, 13.8349—Code Requirements for Nuclear Safety-Related Concrete Structures, 7.7350.2R—Concrete Structures for Containment of Hazardous Materials, 4.2357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.16362.1R—Guide for the Design of Durable Parking Structures, 3.5364.3R—Guide for Cementitious Repair Material Data Sheet, Ch. 5

423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 2.4440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 6.10506R—Guide to Shotcrete, 5.8506.2—Specification for Shotcrete, 3.11506.5R—Guide for Specifying Underground Shotcrete, Ch. 19523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.5530—Building Code Requirements for Masonry Structures, 1.13.4

Protection of slope230.1R—Report on Soil Cement, 3.3

Protective coatings, see also Protective systems345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 5

222R—Protection of Metals in Concrete Against Corrosion, 3.3, 5.4222.2R—Corrosion of Prestressing Steels, 4.2222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 5.3423.7—Specification for Unbonded Single-Strand Tendon Materials, 1.5, 2.2503R—Use of Epoxy Compounds with Concrete, 4.2549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 6.3

Protective systems222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, Ch. 5546R—Concrete Repair Guide, Ch. 4

201.2R—Guide to Durable Concrete, 7.5.5222.2R—Corrosion of Prestressing Steels, 4.3332.1R—Guide to Residential Concrete Construction, 3.12, 4.6, 4.7362.1R—Guide for the Design of Durable Parking Structures, 4.11362.2R—Guide for Structural Maintenance of Parking Structures, 3.2

Pullout, see Anchorage to concrete

Pulverization230.1R—Report on Soil Cement, 7.2.1.3, 8.2

Pumpability, see also Workability212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.8221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.4

Pumped concrete, see also Placing concrete304.2R—Placing Concrete by Pumping Methods

Pumping304.2R—Placing Concrete by Pumping Methods

212.3R—Chemical Admixtures for Concrete, 6.5213R—Guide for Structural Lightweight-Aggregate Concrete, 3.7304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 3.2

Punching shear, see Shear reinforcement

Quality assurance, see also Quality control121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001


ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 5232.2R—Use of Fly Ash in Concrete, Ch. 5304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, Ch. 6, 5.1311.4R—Guide for Concrete Inspection, App. I318—Building Code Requirements for Structural Concrete, Ch. 5

212.3R—Chemical Admixtures for Concrete, 5.8301—Specifications for Structural Concrete, 1.6303.1—Standard Specification for Cast-in-Place Architectural Concrete, 1.6304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Ch. 6308.1—Standard Specification for Curing Concrete, 1.6330R—Guide for the Design and Construction of Concrete Parking Lots, 6.3330.1—Specification for Unreinforced Concrete Parking Lots, 1.7336.1—Specification for the Construction of Drilled Piers, 1.7349—Code Requirements for Nuclear Safety-Related Concrete Structures, 1.5363R—Report on High-Strength Concrete, 4.7503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.3503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.3503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.13503.4—Standard Specification for Repairing Concrete with Epoxy Mortars, 2.1.3503.7—Specification for Crack Repair by Epoxy Injection, 1.5506.2—Specification for Shotcrete, 1.6506.5R—Guide for Specifying Underground Shotcrete, Ch. 9530—Building Code Requirements for Masonry Structures, 1.15530.1—Specification for Masonry Structures, 1.6

Quality control, see also Quality assurance, Inspection

121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001214R—Evaluation of Strength Test Results of Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing363.2R—Guide to Quality Control and Testing of High-Strength ConcreteITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications

207.5R—Roller-Compacted Mass Concrete, Ch. 6212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, Ch. 6225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 8230.1R—Report on Soil Cement, Ch. 8232.2R—Use of Fly Ash in Concrete, Ch. 5, App.

302.1R—Guide for Concrete Floor and Slab Construction, Ch. 10304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Ch. 6309R—Guide for Consolidation of Concrete, Ch. 16350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 7506R—Guide to Shotcrete, Ch. 9522R—Pervious Concrete, Ch. 8

213R—Guide for Structural Lightweight-Aggregate Concrete, 3.8221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 4.5234R—Guide for the Use of Silica Fume in Concrete, 2.9301—Specifications for Structural Concrete, 4.1.3, 7.3.3, 9.1.3304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 7.11, 11.7304.1R—Guide for the Use of Preplaced Aggregate Concrete for Structural and Mass Concrete Applications, 6.2304.2R—Placing Concrete by Pumping Methods, 6.2325.13R—Concrete Overlays for Pavement Rehabilitation, 2.6330R—Guide for the Design and Construction of Concrete Parking Lots, 6.3351.2R—Foundations for Static Equipment, 5.8351.3R—Foundations for Dynamic Equipment, 5.8357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.3362.1R—Guide for the Design of Durable Parking Structures, 4.14363R—Report on High-Strength Concrete, 4.8, 7.6440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 6.3503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.3.5506.5R—Guide for Specifying Underground Shotcrete, 12.2522.1—Specification for Pervious Concrete Pavement, 1.6523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 6.2530.1—Specification for Masonry Structures, 3.7548.1R—Guide for the Use of Polymers in Concrete, 5.6548.5R—Guide for Polymer Concrete Overlays, 6.1

Radiation shielding221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 11, 7.5

Radioactive waste, see Hazardous material

Rails, see Guideway

Rate of hydration, see also Heat of hydration305R—Hot Weather Concreting, 2.5

MCP INDEX IND-49

Reactions, see also Alkali-aggregate reactivity225R—Guide to the Selection and Use of Hydraulic Cements, 6.12

Ready mixed concrete, see also Mixing or Mixture proportioning

311.5—Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete311.6—Specification for Ready Mixed Concrete Testing Services

232.2R—Use of Fly Ash in Concrete, 6.1233R—Slag Cement in Concrete and Mortar, 6.2304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 4.4304.2R—Placing Concrete by Pumping Methods, 2.6, 4.1, 5.1

Rebound, see also Shotcrete506.1R—Guide to Fiber-Reinforced Shotcrete, 7.5

Recycle, reuse555R—Removal and Reuse of Hardened Concrete

221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 6

Refractory concrete308R—Guide to Curing Concrete, 3.4.4

Refrigeration, see also Cooling360R—Design of Slabs-on-Ground207.4R—Cooling and Insulating Systems for Mass Concrete, 2.7, 3.3

Rehabilitation, see also Repair325.13R—Concrete Overlays for Pavement Rehabilitation364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation


207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 5.2506.1R—Guide to Fiber-Reinforced Shotcrete, 10.3546.2R—Guide to Underwater Repair of Concrete, 3.4.5, 4.3

Reinforced concrete, see Reinforcement – steel or Reinforcement – fiber-reinforced polymer (FRP)

Reinforced masonry530—Building Code Requirements for Masonry Structures, 2.3

Reinforced slabs, see Slabs

Reinforcement corrosion, see also Corrosion222R—Protection of Metals in Concrete Against Corrosion222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures


233R—Slag Cement in Concrete and Mortar, 5.13315—Details and Detailing of Concrete Reinforcement, 2.11318—Building Code Requirements for Structural Concrete, 4.2362.1R—Guide for the Design of Durable Parking Structures, 4.9530—Building Code Requirements for Masonry Structures, 1.13.4530.1—Specification for Masonry Structures, 2.4

Reinforcement – fiber-reinforced polymer (FRP)364.2T—Increasing Shear Capacity Within Existing Reinforced Concrete Structures440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement

Reinforcement – steel222R—Protection of Metals in Concrete Against Corrosion222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures315—Details and Detailing of Concrete Reinforcement364.2T—Increasing Shear Capacity Within Existing Reinforced Concrete Structures408R—Bond and Development of Straight Reinforcing Bars in Tension408.2R—Bond under Cyclic Loads408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension421.1R—Guide to Shear Reinforcement for Slabs423.4R—Corrosion and Repair of Unbonded Single-Strand TendonsITG-7—Specification for Tolerances for Precast Concrete

301—Specifications for Structural Concrete, Sec. 3303R—Guide to Cast-in-Place Architectural Concrete Practice, Ch. 5303.1—Standard Specification for Cast-in-Place Architectural Concrete, Ch. 3309R—Guide for Consolidation of Concrete, Ch. 18318—Building Code Requirements for Structural Concrete, Ch. 7, Ch. 12, 3.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 13, 3.2345R—Guide for Concrete Highway Bridge Deck Construction, Ch. 6349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 7350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 7, Ch.12, App. F, 3.5, 10.5, 10.6, 10.9, H.4352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures, Ch. 4352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, Ch. 5360R—Design of Slabs-on-Ground, Ch. 7, 8.3423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, Ch. 4


441R—High-Strength Concrete Columns, Ch. 2

117—Specifications for Tolerances for Concrete Construction and Materials, 2.1, 2.2201.2R—Guide to Durable Concrete, 7.5216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.3, 2.4.2.2(a), 2.4.2.2(c)224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.5302.1R—Guide for Concrete Floor and Slab Construction, 5.9304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 5.3307—Code Requirements for Reinforced Concrete Chimneys, 2.4313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.4, 4.3, 6.9330R—Guide for the Design and Construction of Concrete Parking Lots, 3.8332—Code Requirements for Residential Concrete, 3.2, 8.6332.1R—Guide to Residential Concrete Construction, 3.10, 4.3334.1R—Concrete Shell Structures Practice, 4.3336.1—Specification for the Construction of Drilled Piers, 2.3, 3.4336.3R—Design and Construction of Drilled Piers, 4.2349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures, 4.3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.10, 2.13, 2.14, 6.6371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 5.2.2.2, 5.3, 7.8.2.2, 372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.5, 4.4, 4.5373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.5, 4.4435R—Control of Deflection in Concrete Structures, 3.3437R—Strength Evaluation of Existing Concrete Buildings, 3.2439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities506R—Guide to Shotcrete, 2.8506.2—Specification for Shotcrete, 2.3506.5R—Guide for Specifying Underground Shotcrete, Ch. 17, 5.3523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 2.8, 4.5524R—Guide to Portland Cement-Based Plaster, 7.2530—Building Code Requirements for Masonry Structures, 1.13530.1—Specification for Masonry Structures, 2.4533R—Guide for Precast Concrete Wall Panels, 4.7543R—Design, Manufacture, and Installation of Concrete Piles, 3.2, 4.3, 5.4546R—Concrete Repair Guide, 3.6549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 3.1, 3.2549R—Report on Ferrocement, 3.3ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 3.3

Reinforcing bars, see Reinforcement – steel and Reinforcement – fiber-reinforced polymer (FRP)

Reinforcing steel, see Reinforcement – steel

Relative alignment, see Tolerances

Removal of concrete, see also Demolition555R—Removal and Reuse of Hardened Concrete

345.2R—Guide for Widening Highway Bridges, 3.2351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 7.5423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 4.5503R—Use of Epoxy Compounds with Concrete, 5.3546R—Concrete Repair Guide, 2.2546.2R—Guide to Underwater Repair of Concrete, 4.1

Removal of forms, see also Formwork306R—Cold Weather Concreting, 6.9308R—Guide to Curing Concrete, 3.3318—Building Code Requirements for Structural Concrete, 6.2345R—Guide for Concrete Highway Bridge Deck Construction, 5.4347—Guide to Formwork for Concrete, 3.7, 5.6349—Code Requirements for Nuclear Safety-Related Concrete Structures, 6.2350—Code Requirements for Environmental Engineering Concrete Structures, 6.2423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.6

Repair224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation364.3R—Guide for Cementitious Repair Material Data Sheet

503.4—Standard Specification for Repairing Concrete with Epoxy Mortars503.5R—Guide for the Selection of Polymer Adhesives with Concrete503.7—Specification for Crack Repair by Epoxy Injection546R—Concrete Repair Guide546.2R—Guide to Underwater Repair of Concrete546.3R—Guide for the Selection of Materials for the Repair of Concrete

210R—Erosion of Concrete in Hydraulic Structures, Ch. 9222.2R—Corrosion of Prestressing Steels, Ch. 6330R—Guide for the Design and Construction of Concrete Parking Lots, Ch. 7345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 6349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures, Ch. 8423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, Ch. 5440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 8440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 8506.5R—Guide for Specifying Underground Shotcrete, Ch. 20524R—Guide to Portland Cement-Based Plaster, Ch. 15

MCP INDEX IND-51

549.1R—Guide for the Design, Construction, and Repair of Ferrocement, Ch. 6

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 5.2302.1R—Guide for Concrete Floor and Slab Construction, 8.14302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, 9.9332.1R—Guide to Residential Concrete Construction, 6.7346—Specification for Cast-in-Place Concrete Pipe, 3.3351.3R—Foundations for Dynamic Equipment, 4.6357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 7.3, 7.4357.2R—Report on Barge-Like Concrete Structures, 8.4372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 5.4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 5.4440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 3.3503R—Use of Epoxy Compounds with Concrete, 5.3522R—Pervious Concrete, 7.8533R—Guide for Precast Concrete Wall Panels, 6.6544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.6548.1R—Guide for the Use of Polymers in Concrete, 4.2548.5R—Guide for Polymer Concrete Overlays, 7.3551.1R—Tilt-Up Concrete Construction Guide, 4.5, 8.2

Required strength211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, 2.2307—Code Requirements for Reinforced Concrete Chimneys, 5.3318—Building Code Requirements for Structural Concrete, 9.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 9.2350—Code Requirements for Environmental Engineering Concrete Structures, 9.2363R—Report on High-Strength Concrete, 3.2421.1R—Guide to Shear Reinforcement for Slabs, 4.1

Reservoir, see Water tanks

Reshoring, see Formwork

Residential concrete, see also Slab-on-ground332—Code Requirements for Residential Concrete332.1R—Guide to Residential Concrete Construction

Response, see Material response, Structural response

Responsibility533.1R—Design Responsibility for Architectural Precast-Concrete Projects

121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001, Sec. 5

311.4R—Guide for Concrete Inspection, Ch. 2

Restoration, see Repair

Restraint, see also Cracking or Shrinkage-compensating concrete

207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, Ch. 5

223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 3.2

Resurfacing, see also Overlays330R—Guide for the Design and Construction of Concrete Parking Lots, 7.6

Retarding admixtures, see Admixtures

Retempering, see also Setting time305R—Hot Weather Concreting, 3.6

Retrofit341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges

440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 8

Rheology238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete

309R—Guide for Consolidation of Concrete, Ch. 2309.1R—Report on Behavior of Fresh Concrete During Vibration, Ch. 3

234R—Guide for the Use of Silica Fume in Concrete, 10.7

Roller-compacted concrete, see also Mass concrete

207.5R—Roller-Compacted Mass Concrete325.10R—Report on Roller-Compacted Concrete Pavements

232.2R—Use of Fly Ash in Concrete, 6.4309R—Guide for Consolidation of Concrete, 9.5

Roofs, see also Slabs523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units

523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, Ch. 6

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.2318—Building Code Requirements for Structural Concrete, 9.5347—Guide to Formwork for Concrete, 6.4


350—Code Requirements for Environmental Engineering Concrete Structures, 9.5362.1R—Guide for the Design of Durable Parking Structures, 3.6372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 3.4523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 5.3, 6.3549R—Report on Ferrocement, 6.5

Safety364.3R—Guide for Cementitious Repair Material Data Sheet, Ch. 7

506.5R—Guide for Specifying Underground Shotcrete, Ch. 15548.1R—Guide for the Use of Polymers in Concrete, Ch. 6

304.2R—Placing Concrete by Pumping Methods, 2.7318—Building Code Requirements for Structural Concrete, 20.7336.3R—Design and Construction of Drilled Piers, 4.5347—Guide to Formwork for Concrete, 2.4, 3.1349—Code Requirements for Nuclear Safety-Related Concrete Structures, 20.7350—Code Requirements for Environmental Engineering Concrete Structures, 20.7351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 6.6440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 1.3, 5.3503R—Use of Epoxy Compounds with Concrete, 9.2503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3.11503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3.6503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.3.7503.4—Standard Specification for Repairing Concrete with Epoxy Mortars, 2.3.6503.5R—Guide for the Selection of Polymer Adhesives with Concrete, 1.2503.7—Specification for Crack Repair by Epoxy Injection, 1.7548.3R—Report on Polymer-Modified Concrete, 4.3.6548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks, 1.7548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks, 1.7ITG-3—Report on Bridge Decks Free of Steel Reinforcement, 5.6

Safety-related structures349.3R—Evaluation of Existing Nuclear Safety-Related Concrete Structures

Salt attack201.2R—Guide to Durable Concrete, 6.3

Sampling, see also Testing207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, Ch. 4

225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 8228.1R—In-Place Methods to Estimate Concrete Strength, Ch. 5364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, Ch. 5, 2.7, 7.5437R—Strength Evaluation of Existing Concrete Buildings, Ch. 3548.7—Test Method for Load Capacity of Polymer Concrete Underground Utility Structures, Sec. 7ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 11ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 15, Ch. 16, 17.11, 17.12

212.3R—Chemical Admixtures for Concrete, 1.4229R—Controlled Low-Strength Materials, 7.2232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 3.5232.2R—Use of Fly Ash in Concrete, 5.5311.6—Specification for Ready Mixed Concrete Testing Services, 2.1, 2.2313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.3363.2R—Guide to Quality Control and Testing of High-Strength Concrete, 4.3440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement, Ch. 11506.4R—Guide for the Evaluation of Shotcrete, 7.2

Sanitary engineering structures, see Water tanks

Scaling, see also Curing201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.19302.1R—Guide for Concrete Floor and Slab Construction, 11.5364.3R—Guide for Cementitious Repair Material Data Sheet, 5.12

345R—Guide for Concrete Highway Bridge Deck Construction, 1.5503.7—Specification for Crack Repair by Epoxy Injection, 2.1, 3.3546.2R—Guide to Underwater Repair of Concrete, 2.7

Scour357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 5.3

Sealants, see also Joints345.1R—Guide for Maintenance of Concrete Bridge Members, Ch. 5

224.1R—Causes, Evaluation, and Repair of Cracks in Concrete Structures, 3.3224.3R—Joints in Concrete Construction, 2.2, 2.6, 2.7302.1R—Guide for Concrete Floor and Slab Construction, 5.8325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 4.7330R—Guide for the Design and Construction of Concrete Parking Lots, 7.2

MCP INDEX IND-53

350.2R—Concrete Structures for Containment of Hazardous Materials, 3.2362.1R—Guide for the Design of Durable Parking Structures, 4.9362.2R—Guide for Structural Maintenance of Parking Structures, 3.2372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.7373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.8546R—Concrete Repair Guide, 4.6

Secondary containment, see Containment

Seepage control, see also Watertightness207.5R—Roller-Compacted Mass Concrete, 4.7

Segregation, see also Consolidation212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.6234R—Guide for the Use of Silica Fume in Concrete, 4.5

Seismic, see also Earthquake requirements and loading

341.2R—Seismic Analysis and Design of Concrete Bridge Systems341.3R—Seismic Evaluation and Retrofit Techniques for Concrete Bridges350.3—Seismic Design of Liquid-Containing Concrete Structures374.1—Acceptance Criteria for Moment Frames Based on Structural Testing408.2R—Bond under Cyclic Loads421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete StructuresITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic ApplicationsT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

318—Building Code Requirements for Structural Concrete, Ch. 21349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 21350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 21357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, App. B421.1R—Guide to Shear Reinforcement for Slabs, Ch. 7

213R—Guide for Structural Lightweight-Aggregate Concrete, 5.14315—Details and Detailing of Concrete Reinforcement, 2.10 355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 9.5, 9.6

371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 6.6373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.7423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 9.2530—Building Code Requirements for Masonry Structures, 1.14

Selection of cements, see also Cement225R—Guide to the Selection and Use of Hydraulic Cements

Self-consolidating concrete237R—Self-Consolidating Concrete309R—Guide for Consolidation of Concrete, Ch. 15

238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 5.3, 5.4

Serviceability350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 9355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, Ch. 9358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, Ch. 5440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 4

318—Building Code Requirements for Structural Concrete, 18.4343R—Analysis and Design of Reinforced Concrete Bridge Structures, 8.2347.2R—Guide for Shoring/Reshoring of Concrete Multistory Buildings, 4.4352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures, 3.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 4.3371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 5.1.4, 5.2.1.6.3372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.1373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 3.1423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.8440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 6.2440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 8.3440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 10.2533R—Guide for Precast Concrete Wall Panels, 2.5549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 4.4

Service life365.1R—Service-Life Prediction


Settlement, see also Deformation224R—Control of Cracking in Concrete Structures, 8.4343R—Analysis and Design of Reinforced Concrete Bridge Structures, 5.4.4347—Guide to Formwork for Concrete, 2.8

Setting time, see also Fresh concrete, Curing212.3R—Chemical Admixtures for Concrete, Ch. 4

233R—Slag Cement in Concrete and Mortar, 4.2234R—Guide for the Use of Silica Fume in Concrete, 4.4308R—Guide to Curing Concrete, R1.4, 2.9, 3.1, 3.2, 3.3309.1R—Report on Behavior of Fresh Concrete During Vibration, 3.1

Sewage treatment, see also Sanitary engineering structures

Shear design, see Shear strength

Shear friction, see also Shear strength445R—Recent Approaches to Shear Design of Structural Concrete, Ch. 5

Shear reinforcement, see also Shear strength421.1R—Guide to Shear Reinforcement for Slabs421.2R—Seismic Design of Punching Shear Reinforcement in Flat Plates

350—Code Requirements for Environmental Engineering Concrete Structures, 11.5

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.4440.4R—Prestressing Concrete Structures with FRP Tendons, 5.3, 5.4

Shear strength364.2T—Increasing Shear Capacity Within Existing Reinforced Concrete Structures421.1R—Guide to Shear Reinforcement for Slabs445R—Recent Approaches to Shear Design of Structural Concrete

318—Building Code Requirements for Structural Concrete, Ch. 11349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 11350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 11, 17.4, 17.5440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 9440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Ch. 11440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 5

ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 6

207.1R—Guide to Mass Concrete, 3.8207.5R—Roller-Compacted Mass Concrete, 3.2.3213R—Guide for Structural Lightweight-Aggregate Concrete, 5.5343R—Analysis and Design of Reinforced Concrete Bridge Structures, 7.3, 9.4352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 4.3358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 6.3506.1R—Guide to Fiber-Reinforced Shotcrete, 7.3523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 7.5, 7.6530—Building Code Requirements for Masonry Structures, 2.2.5, 2.3.5, 4.6544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 3.3, 3.4ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 6.5

Shear studs, see Shear reinforcement

Shear transfer350.3—Seismic Design of Liquid-Containing Concrete Structures, 5.2445R—Recent Approaches to Shear Design of Structural Concrete, 4.3

Shearheads, see Shear reinforcement

Shearwalls, see also Walls318—Building Code Requirements for Structural Concrete, Ch. 11, Ch. 14349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 11, Ch. 14

550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, 3.1, 3.3

Sheathing for unbonded post-tensioning, see also Prestressed concrete or Post-tensioning

301—Specifications for Structural Concrete, 9.2.1318—Building Code Requirements for Structural Concrete, 18.16423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 4.2.2423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 3.2423.7—Specification for Unbonded Single-Strand Tendon Materials, 1.5, 2.3

Shells334.1R—Concrete Shell Structures Practice334.3R—Construction of Concrete Shells Using Inflated Forms

MCP INDEX IND-55

318—Building Code Requirements for Structural Concrete, Ch. 19349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch.19349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures, Ch. 4350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 19

307—Code Requirements for Reinforced Concrete Chimneys, 5.5308R—Guide to Curing Concrete, 3.4.6347—Guide to Formwork for Concrete, 6.4

Shoring, see Formwork

Short duration, see Impact

Shotcrete506R—Guide to Shotcrete506.1R—Guide to Fiber-Reinforced Shotcrete506.2—Specification for Shotcrete506.5R—Guide for Specifying Underground Shotcrete

334.3R—Construction of Concrete Shells Using Inflated Forms, Ch. 4

372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.2, 4.2373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.2, 4.2544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 3.5

Shrinkage, see also Creep209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete

209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 4, 2.3, 2.4, 2.8, 3.7209.1R—Report on Factors Affecting Shrinkage and Creep of Hardened Concrete, Ch. 2223—Standard Practice for the Use of Shrinkage-Compensating Concrete, App. A, App. C, 1.2, 2.1224R—Control of Cracking in Concrete Structures, Ch. 3, 8.3, 8.6305R—Hot Weather Concreting, Ch. 1, Ch. 2, Ch. 4360R—Design of Slabs-on-Ground, Ch. 13435R—Control of Deflection in Concrete Structures, Ch. 2440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 10

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.9, 5.7230.1R—Report on Soil Cement, 5.6233R—Slag Cement in Concrete and Mortar, 5.4234R—Guide for the Use of Silica Fume in Concrete, 3.6318—Building Code Requirements for Structural Concrete, 7.12343R—Analysis and Design of Reinforced Concrete Bridge Structures, 3.2, 5.4, 13.5350—Code Requirements for Environmental Engineering Concrete Structures, 7.12363R—Report on High-Strength Concrete, 5.13

523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 3.2530—Building Code Requirements for Masonry Structures, 1.8544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.6549R—Report on Ferrocement, 4.8555R—Removal and Reuse of Hardened Concrete, 5.4

Shrinkage-compensating concrete, see also Expansive cement

223—Standard Practice for the Use of Shrinkage-Compensating Concrete

301—Specifications for Structural Concrete, Sec. 10360R—Design of Slabs-on-Ground, Ch. 8, App. 5

Sidewalks, see also Slab-on-ground117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 12

224.3R—Joints in Concrete Construction, 4.2343R—Analysis and Design of Reinforced Concrete Bridge Structures, 2.2

Silica fume201.2R—Guide to Durable Concrete, 5.4211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, 3.6, 4.4221.1R—Report on Alkali-Aggregate Reactivity, 5.6.4234R—Guide for the Use of Silica Fume in Concrete301—Specifications for Structural Concrete, 4.2302.1R—Guide for Concrete Floor and Slab Construction, 8.4303.1—Standard Specification for Cast-in-Place Architectural Concrete, 2.2.4318—Building Code Requirements for Structural Concrete, 4.4345R—Guide for Concrete Highway Bridge Deck Construction, 2.6.2362.1R—Guide for the Design of Durable Parking Structures, 3.3.3363R—Report on High-Strength Concrete, 2.4.2546R—Concrete Repair Guide, 3.2.14

Silos, see also Bins313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials549R—Report on Ferrocement, 6.3

Single-strand tendons, see also Prestressed concrete

423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons423.7—Specification for Unbonded Single-Strand Tendon Materials

Siphons, see Tolerances

Site investigation, see Inspection


Skid resistance503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System

201.2R—Guide to Durable Concrete, 8.6325.10R—Report on Roller-Compacted Concrete Pavements, 9.3325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2345R—Guide for Concrete Highway Bridge Deck Construction, 2.7503R—Use of Epoxy Compounds with Concrete, 4.4

Slab-column connection, see also Column-slab connection

352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures

421.1R—Guide to Shear Reinforcement for Slabs, Ch.7

Slabs117—Specifications for Tolerances for Concrete Construction and Materials301—Specifications for Structural Concrete302.1R—Guide for Concrete Floor and Slab Construction330R—Guide for the Design and Construction of Concrete Parking Lots352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures360R—Design of Slabs-on-Ground421.1R—Guide to Shear Reinforcement for Slabs435.8R—Observed Deflections of Reinforced Concrete Slab Systems, and Causes of Large Deflections

223—Standard Practice for the Use of Shrinkage-Compensating Concrete, App. A, 3.3, 3.4, 3.6309R—Guide for Consolidation of Concrete, Ch. 10318—Building Code Requirements for Structural Concrete, Ch. 13, 10.6, 11.11332.1R—Guide to Residential Concrete Construction, Ch. 5349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 13, 10.6, 11.12350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 13, App. H, 10.14, 11.12, 18.12435R—Control of Deflection in Concrete Structures, Ch. 4523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, Ch. 4

209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 4.2212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 5.7232.2R—Use of Fly Ash in Concrete, 7.4308R—Guide to Curing Concrete, 3.1315—Details and Detailing of Concrete Reinforcement, 2.10343R—Analysis and Design of Reinforced Concrete Bridge Structures, 10.4363R—Report on High-Strength Concrete, 6.3

423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.2, 3.3544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 3.1ITG-3—Report on Bridge Decks Free of Steel Reinforcement, 3.2

Slabs-on-ground302.1R—Guide for Concrete Floor and Slab Construction360R—Design of Slabs-on-GroundSP-15—Field Reference Manual

224.3R—Joints in Concrete Construction, Ch. 5332—Code Requirements for Residential Concrete, Ch. 8350—Code Requirements for Environmental Engineering Concrete Structures, App. H440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, App. A551.1R—Tilt-Up Concrete Construction Guide, Ch. 4, 7.3

223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 3.4308R—Guide to Curing Concrete, 3.1332.1R—Guide to Residential Concrete Construction, 5.1

Slag cement, see Ground granulated blast-furnace slag

Sleeves349—Code Requirements for Nuclear Safety-Related Concrete Structures, 6.3439.3R—Types of Mechanical Splices for Reinforcing Bars, 1.3, 3.2530—Building Code Requirements for Masonry Structures, 1.16

Slipform, pavement, see Pavements

Slipform, vertical117—Specifications for Tolerances for Concrete Construction and Materials, Sec. 7

304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 5.4.2.5308R—Guide to Curing Concrete, 3.4.2

Slope protection230.1R—Report on Soil Cement, 3.3

Slump, see also Properties of concrete211.3R—Guide for Selecting Proportions for No-Slump Concrete, 3.2212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.3, 6.2, 6.3232.2R—Use of Fly Ash in Concrete, 7.4233R—Slag Cement in Concrete and Mortar, 4.4234R—Guide for the Use of Silica Fume in Concrete, 4.3304.2R—Placing Concrete by Pumping Methods, 4.4304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 5.3, 7.5305R—Hot Weather Concreting, 3.5

MCP INDEX IND-57

306R—Cold Weather Concreting, 2.7311.6—Specification for Ready Mixed Concrete Testing Services, 2.3.1, 3.3.8346—Specification for Cast-in-Place Concrete Pipe, 2.1506.5R—Guide for Specifying Underground Shotcrete, 8.4

Slurry, see also Grout336.1—Specification for the Construction of Drilled Piers, 2.6, 3.7336.3R—Design and Construction of Drilled Piers, 4.4

Soil cement230.1R—Report on Soil Cement

232.2R—Use of Fly Ash in Concrete, 8.3

Soil cement slurry229R—Controlled Low-Strength Materials

Soil exploration336.3R—Design and Construction of Drilled Piers, 2.3, 2.4, 5.3, 5.4, 5.6

Soil mechanics336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats


Soil properties302.1R—Guide for Concrete Floor and Slab Construction, 4.1336.3R—Design and Construction of Drilled Piers, 2.4

Soil stabilization230.1R—Report on Soil Cement, 2.2346—Specification for Cast-in-Place Concrete Pipe, 3.1

Soil support360R—Design of Slabs-on-Ground, Ch. 3

437R—Strength Evaluation of Existing Concrete Buildings, 4.1

Soil test230.1R—Report on Soil Cement, Ch. 8

336.1—Specification for the Construction of Drilled Piers, 1.6360R—Design of Slabs-on-Ground, 3.3

Soils230.1R—Report on Soil Cement, Ch. 4360R—Design of Slabs-on-Ground, Ch. 3

302.1R—Guide for Concrete Floor and Slab Construction, 4.1325.10R—Report on Roller-Compacted Concrete Pavements, 4.3336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, 2.2, 2.3, 3.2, 3.3, 6.7351.2R—Foundations for Static Equipment, 4.5

Spacing, see Detailing of reinforcement

Spalling, see also Surface defects201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.20

345R—Guide for Concrete Highway Bridge Deck Construction, 1.4506.1R—Guide to Fiber-Reinforced Shotcrete, 10.5

Span length318—Building Code Requirements for Structural Concrete, 8.9349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.7350—Code Requirements for Environmental Engineering Concrete Structures, 8.7

Special inspections311.4R—Guide for Concrete Inspection, 3.3

Specifications211.5R—Guide for Submittal of Concrete Proportions212.3R—Chemical Admixtures for Concrete301—Specifications for Structural Concrete303.1—Standard Specification for Cast-in-Place Architectural Concrete305.1—Specification for Hot Weather Concreting306.1—Standard Specification for Cold Weather Concreting308R—Guide to Curing Concrete308.1—Standard Specification for Curing Concrete311.6—Specification for Ready Mixed Concrete Testing Services318—Building Code Requirements for Structural Concrete330.1—Specification for Unreinforced Concrete Parking Lots336.1—Specification for the Construction of Drilled Piers346—Specification for Cast-in-Place Concrete Pipe349—Code Requirements for Nuclear Safety-Related Concrete Structures350—Code Requirements for Environmental Engineering Concrete Structures423.7—Specification for Unbonded Single-Strand Tendon Materials440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars440.6—Specification for Carbon and Glass Fiber-Reinforced Polymer Bar Materials for Concrete Reinforcement503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System503.4—Standard Specification for Repairing Concrete with Epoxy Mortars503.7—Specification for Crack Repair by Epoxy Injection506.2—Specification for Shotcrete522.1—Specification for Pervious Concrete Pavement530—Building Code Requirements for Masonry Structures530.1—Specification for Masonry Structures


548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage DecksITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic ApplicationsITG-7—Specification for Tolerances for Precast ConcreteSP-15—Field Reference Manual

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, Ch. 3232.2R—Use of Fly Ash in Concrete, Ch. 5234R—Guide for the Use of Silica Fume in Concrete, Ch. 7439.3R—Types of Mechanical Splices for Reinforcing Bars, Ch. 2

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 11.2213R—Guide for Structural Lightweight-Aggregate Concrete, 5.13233R—Slag Cement in Concrete and Mortar, 1.8303R—Guide to Cast-in-Place Architectural Concrete Practice, 2.5304.4R—Placing Concrete with Belt Conveyors, 2.7306R—Cold Weather Concreting, 1.2309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 2.1313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 1.4325.11R—Accelerated Techniques for Concrete Paving, 3.4330R—Guide for the Design and Construction of Concrete Parking Lots, 4.6343R—Analysis and Design of Reinforced Concrete Bridge Structures, 3.4371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 1.3440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 14.2548.3R—Polymer-Modified Concrete, 3.5

Spillways210R—Erosion of Concrete in Hydraulic Structures

207.5R—Roller-Compacted Mass Concrete, 4.8

Spiral reinforcement, see Detailing of reinforcement

Splice length408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

318—Building Code Requirements for Structural Concrete, Ch. 12349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 12350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 12

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 6.8, 13.2

Splices, see also Reinforcement – steel408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension439.3R—Types of Mechanical Splices for Reinforcing Bars

318—Building Code Requirements for Structural Concrete, Ch. 12349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 12440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 11550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, Ch. 5ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 7

315—Details and Detailing of Concrete Reinforcement, 2.7350—Code Requirements for Environmental Engineering Concrete Structures, 12.14 through 12.19440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 6.8, 13.2530—Building Code Requirements for Masonry Structures, 1.13543R—Design, Manufacture, and Installation of Concrete Piles, 3.7

Splitting strength, see Strength

Stability225R—Guide to the Selection and Use of Hydraulic Cements357.2R—Report on Barge-Like Concrete Structures530—Building Code Requirements for Masonry Structures

334.1R—Concrete Shell Structures Practice, Ch. 5350.4R—Design Considerations for Environmental Engineering Concrete Structures, Ch. 3

207.5R—Roller-Compacted Mass Concrete, 4.3351.2R—Foundations for Static Equipment, 3.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 5.2, 6.2

Stacking tubes313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials

Static equipment350.2R—Concrete Structures for Containment of Hazardous Materials351.2R—Foundations for Static Equipment

Statistical analysis214R—Evaluation of Strength Test Results of Concrete

209.2R—Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, App. B, 3.2214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, Ch. 6, 2.5228.1R—In-Place Methods to Estimate Concrete Strength, Ch. 3, 6.2

MCP INDEX IND-59

363.2R—Guide to Quality Control and Testing of High-Strength Concrete, Ch. 5

121R—Guide for Concrete Construction Quality Systems in Conformance with ISO 9001, 8.4408R—Bond and Development of Straight Reinforcing Bars in Tension, 4.5

Steam curing, see also Accelerated curing308R—Guide to Curing Concrete, 2.6, 2.7

Steel reinforcement, see Reinforcement – steel

Stiffness318—Building Code Requirements for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery530—Building Code Requirements for Masonry Structures

224.2R—Cracking of Concrete Members in Direct Tension, 4.1350—Code Requirements for Environmental Engineering Concrete Structures, 8.6351.2R—Foundations for Static Equipment, 3.3

Stilling basin210R—Erosion of Concrete in Hydraulic Structures, 3.2

Stirrups, see also Shear reinforcement315—Details and Detailing of Concrete Reinforcement

440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 9.3

Storage304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing


212.3R—Chemical Admixtures for Concrete, 2.7221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 7.6232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 4.1232.2R—Use of Fly Ash in Concrete, 6.8233R—Slag Cement in Concrete and Mortar, 2.1303.1—Standard Specification for Cast-in-Place Architectural Concrete, 1.7304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, 3.1318—Building Code Requirements for Structural Concrete, 3.7330.1—Specification for Unreinforced Concrete Parking Lots, 1.5364.3R—Guide for Cementitious Repair Material Data Sheet, Ch. 6

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.7

350—Code Requirements for Environmental Engineering Concrete Structures, 3.7363R—Report on High-Strength Concrete, 4.2.1423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 3.4423.7—Specification for Unbonded Single-Strand Tendon Materials, 1.7440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 6.1440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 5.2440.5—Specification for Construction with Fiber-Reinforced Polymer Reinforcing Bars, 1.5503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.4503.2—Standard Specification for Bonding Plastic Concrete to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.1.4503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.1.4503.4—Standard Specification for Repairing Concrete with Epoxy Mortars, 2.1.4503.7—Specification for Crack Repair by Epoxy Injection, 1.6506R—Guide to Shotcrete, 2.2506.2—Specification for Shotcrete, 2.10523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 5.1533R—Guide for Precast Concrete Wall Panels, 5.8, 6.3544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 3.4548.8—Specification for Type EM (Epoxy Multi-Layer) Polymer Overlay for Bridge and Parking Garage Decks, 1.6548.9—Specification for Type ES (Epoxy Slurry) Polymer Overlay for Bridge and Parking Garage Decks, 1.6

Storage tanks, see also Water tanks350.3—Seismic Design of Liquid-Containing Concrete Structures549R—Report on Ferrocement, 6.4

Strain, see also Creep or Deflection363R—Report on High-Strength Concrete435R—Control of Deflection in Concrete Structures

207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.7207.5R—Roller-Compacted Mass Concrete, 3.8224R—Control of Cracking in Concrete Structures, 7.3

Streaking, see Surface defects

Strength, see also Compressive strength214R—Evaluation of Strength Test Results of Concrete214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete225R—Guide to the Selection and Use of Hydraulic Cements228.1R—In-Place Methods to Estimate Concrete Strength


318—Building Code Requirements for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery352R—Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures437R—Strength Evaluation of Existing Concrete Buildings440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures549.1R—Guide for the Design, Construction, and Repair of Ferrocement

211.5R—Guide for Submittal of Concrete Proportions, Ch. 4306R—Cold Weather Concreting, Ch. 9325.10R—Report on Roller-Compacted Concrete Pavements, Ch. 5350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 9, Ch. 20, 5.4, 10.17, 16.10, 19.3, D.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, Ch. 4

207.1R—Guide to Mass Concrete, 3.2207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.2207.5R—Roller-Compacted Mass Concrete, 3.2211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, 2.2213R—Guide for Structural Lightweight-Aggregate Concrete, 4.10233R—Slag Cement in Concrete and Mortar, 5.1308R—Guide to Curing Concrete, 2.6309R—Guide for Consolidation of Concrete, 17.1309.5R—Compaction of Roller-Compacted Concrete, 3.2, 6.5325.11R—Accelerated Techniques for Concrete Paving, 7.1325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2330R—Guide for the Design and Construction of Concrete Parking Lots, 4.2346—Specification for Cast-in-Place Concrete Pipe, 2.1352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 4.5363R—Report on High-Strength Concrete, 4.9, 5.6371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.1.2.2.2372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.1373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 3.1440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, 6.1549R—Report on Ferrocement, 4.2, 4.3555R—Removal and Reuse of Hardened Concrete, 5.4ITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1, 4.2

Strength design318—Building Code Requirements for Structural Concrete349—Code Requirements for Nuclear Safety-Related Concrete Structures350—Code Requirements for Environmental Engineering Concrete Structures423.3R—Recommendations for Concrete Members Prestressed with Unbonded TendonsT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

213R—Guide for Structural Lightweight-Aggregate Concrete, Ch. 5, 4.13307—Code Requirements for Reinforced Concrete Chimneys, Ch. 5343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 7421.1R—Guide to Shear Reinforcement for Slabs, Ch. 4530—Building Code Requirements for Masonry Structures, Ch. 3

336.3R—Design and Construction of Drilled Piers, 3.3440.4R—Prestressing Concrete Structures with FRP Tendons, 3.2

Strength of early-age concrete347.2R—Guide for Shoring/Reshoring of Concrete Multistory Buildings, Ch. 4

Strength evaluation, see also Testing or Evaluation

437R—Strength Evaluation of Existing Concrete BuildingsSP-15—Field Reference Manual

318—Building Code Requirements for Structural Concrete, Ch. 20, 16.10349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 20, 16.10350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 20, 16.10

214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results, 3.2

Strengthening440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures

440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 8, 10.2, 10.3

Stress224.2R—Cracking of Concrete Members in Direct Tension318—Building Code Requirements for Structural Concrete351.2R—Foundations for Static Equipment357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures363R—Report on High-Strength Concrete408.2R—Bond under Cyclic Loads530—Building Code Requirements for Masonry Structures543R—Design, Manufacture, and Installation of Concrete Piles

MCP INDEX IND-61

307—Code Requirements for Reinforced Concrete Chimneys, Ch. 6350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 6

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 3.4343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.5347—Guide to Formwork for Concrete, 2.3358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 5.3423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 2.3523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.3

Stress relaxation209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 5.3, 5.4

Stress-strain relationship, see also Modulus of elasticity

445R—Recent Approaches to Shear Design of Structural Concrete, 2.3

Structural analysis318—Building Code Requirements for Structural Concrete341.2R—Seismic Analysis and Design of Concrete Bridge Systems343R—Analysis and Design of Reinforced Concrete Bridge Structures350—Code Requirements for Environmental Engineering Concrete Structures358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures530—Building Code Requirements for Masonry Structures

336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats, Ch. 3371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, Ch. 5

523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 4.1550.1R—Guide to Emulating Cast-in-Place Detailing for Seismic Design of Precast Concrete Structures, 3.3

Structural design, see also Design factors307—Code Requirements for Reinforced Concrete Chimneys315—Details and Detailing of Concrete Reinforcement318—Building Code Requirements for Structural Concrete330R—Guide for the Design and Construction of Concrete Parking Lots336.2R—Suggested Analysis and Design Procedures for Combined Footings and Mats336.3R—Design and Construction of Drilled Piers341.2R—Seismic Analysis and Design of Concrete Bridge Systems

343R—Analysis and Design of Reinforced Concrete Bridge Structures349—Code Requirements for Nuclear Safety-Related Concrete Structures349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples350—Code Requirements for Environmental Engineering Concrete Structures350.1—Tightness Testing of Environmental Engineering Concrete Structures350.3—Seismic Design of Liquid-Containing Concrete Structures352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures357.2R—Report on Barge-Like Concrete Structures358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures360R—Design of Slabs-on-Ground362.1R—Guide for the Design of Durable Parking Structures423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons530—Building Code Requirements for Masonry Structures544.4R—Design Considerations for Steel Fiber-Reinforced Concrete549.1R—Guide for the Design, Construction, and Repair of Ferrocement

347—Guide to Formwork for Concrete, Ch. 2523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, Ch. 4

533.1R—Design Responsibility for Architectural Precast-Concrete Projects, 2.2

Structural diaphragms, see also Lateral-force resisting system

318—Building Code Requirements for Structural Concrete, 21.11

Structural drawings, see Detailing of reinforcement

Structural integrity318—Building Code Requirements for Structural Concrete, 7.13, 16.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 7.13, 16.5350—Code Requirements for Environmental Engineering Concrete Structures, 7.13, 16.5352.1R—Recommendations for Design of Slab-Column Connections in Monolithic Reinforced Concrete Structures, 5.3

Structural plain concrete, see Plain concrete

Structural modeling, see Modeling

Structural response209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Ch. 3


Structural walls, see Walls

Strut-and-tie models, see also Shear design318—Building Code Requirements for Structural Concrete, App. A445R—Recent Approaches to Shear Design of Structural Concrete, Ch. 6

Stucco, see also Plastering308R—Guide to Curing Concrete, 3.4.5

Studs, see also Slab reinforcement349.2R—Guide to the Concrete Capacity Design (CCD) Method—Embedment Design Examples, App. A

Styrene-butadiene latex, see also Polymer concrete

548.4—Standard Specification for Latex-Modified Concrete (LMC) Overlays

548.3R—Report on Polymer-Modified Concrete, 4.1


Subbase, see also Pavements325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.1332—Code Requirements for Residential Concrete, 8.2360R—Design of Slabs-on-Ground, 3.3522.1—Specification for Pervious Concrete Pavement, 2.1, 3.2

Subgrades, see also Pavements330R—Guide for the Design and Construction of Concrete Parking Lots, App. B, 3.4, 5.2, 6.2

301—Specifications for Structural Concrete, 5.3.1306R—Cold Weather Concreting, 4.4325.10R—Report on Roller-Compacted Concrete Pavements, 7.2325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.1330.1—Specification for Unreinforced Concrete Parking Lots, 3.1, 3.2350—Code Requirements for Environmental Engineering Concrete Structures, H.2360R—Design of Slabs-on-Ground, 3.3, 3.4522R—Pervious Concrete, 7.1522.1—Specification for Pervious Concrete Pavement, 3.1

Substructures, see also Bridges343R—Analysis and Design of Reinforced Concrete Bridge Structures, Ch. 11, 12.4

345.1R—Guide for Maintenance of Concrete Bridge Members, 3.5345.2R—Guide for Widening Highway Bridges, 3.7

Subsurface conditions, see also Subbase343R—Analysis and Design of Reinforced Concrete Bridge Structures, 6.2.5, 6.3.3

351.2R—Foundations for Static Equipment, 5.1351.3R—Foundations for Dynamic Equipment, 5.1

Sulfate attack, see also Durability201.2R—Guide to Durable Concrete, 6.2, App. A

232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 2.3.2233R—Slag Cement in Concrete and Mortar, 5.9234R—Guide for the Use of Silica Fume in Concrete, 10.3

Sulfate exposure, see also Durability318—Building Code Requirements for Structural Concrete, 4.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 4.3350—Code Requirements for Environmental Engineering Concrete Structures, 4.3

Sump construction350.2R—Concrete Structures for Containment of Hazardous Materials, 4.1

Superstructures, see also Bridges341.2R—Seismic Analysis and Design of Concrete Bridge Systems, 4.2, 4.3343R—Analysis and Design of Reinforced Concrete Bridge Structures, 6.5, 10.2, 10.3, 12.2345.1R—Guide for Maintenance of Concrete Bridge Members, 3.4

Surface defects, see also Abrasion or Chemical attack

201.1R—Guide for Conducting a Visual Inspection of Concrete in Service309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces

302.1R—Guide for Concrete Floor and Slab Construction, Ch. 11

308R—Guide to Curing Concrete, 3.4.8309R—Guide for Consolidation of Concrete, 7.7345R—Guide for Concrete Highway Bridge Deck Construction, 10.7524R—Guide to Portland Cement-Based Plaster, 15.5533R—Guide for Precast Concrete Wall Panels, 7.2549.1R—Guide for the Design, Construction, and Repair of Ferrocement, 6.2

Surface finish302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, 9.6

Surface preparation, see also Repair or Overlays503R—Use of Epoxy Compounds with Concrete, Ch. 5548.5R—Guide for Polymer Concrete Overlays, Ch. 4555R—Removal and Reuse of Hardened Concrete, Ch. 4

302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, 9.8

MCP INDEX IND-63

503.1—Standard Specification for Bonding Hardened Concrete Steel, Wood, Brick, and Other Materials to Hardened Concrete with a Multi-Component Epoxy Adhesive, 2.3503.3—Standard Specification for Producing a Skid-Resistant Surface on Concrete by the Use of a Multi-Component Epoxy System, 2.3506R—Guide to Shotcrete, 5.2506.2—Specification for Shotcrete, 3.3506.5R—Guide for Specifying Underground Shotcrete, 16.3546R—Concrete Repair Guide, 2.3546.2R—Guide to Underwater Repair of Concrete, 4.2548.3R—Report on Polymer-Modified Concrete, 4.3.2551.1R—Tilt-Up Concrete Construction Guide, 8.1

Surveys, see also Testing, Evaluation201.1R—Guide for Conducting a Visual Inspection of Concrete in Service

357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 7.2437R—Strength Evaluation of Existing Concrete Buildings, 2.2

Synthetic fibers, see also Fiber-reinforced concrete

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures

506.1R—Guide to Fiber-Reinforced Shotcrete, 3.2544.1R—Report on Fiber-Reinforced Concrete, Ch. 4

Tanks, see also Water tanks350.1—Tightness Testing of Environmental Engineering Concrete Structures350.3—Seismic Design of Liquid-Containing Concrete Structures371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons549R—Report on Ferrocement, 6.4

T-beams, see also Flexural member318—Building Code Requirements for Structural Concrete, 8.12349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.10

Temperature, see also Cooling or Insulating209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures305R—Hot Weather Concreting306R—Cold Weather Concreting306.1—Standard Specification for Cold Weather Concreting

349—Code Requirements for Nuclear Safety-Related Concrete Structures, App. E440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 10, A.2

ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 8ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 2, 17.8

207.1R—Guide to Mass Concrete, 1.3, 2.8, 4.7207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 4.3, 4.4, 4.5207.5R—Roller-Compacted Mass Concrete, 4.4212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.4238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.8301—Specifications for Structural Concrete, 5.3.2302.1R—Guide for Concrete Floor and Slab Construction, 9.9304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 4.6305.1—Specification for Hot Weather Concreting, 3.2308R—Guide to Curing Concrete, 1.3, 4.5, 4.7325.11R—Accelerated Techniques for Concrete Paving, 5.2332.1R—Guide to Residential Concrete Construction, 6.5, 6.6350—Code Requirements for Environmental Engineering Concrete Structures, 7.12351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 7.2435R—Control of Deflection in Concrete Structures, 2.7440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.2, 6.2506.5R—Guide for Specifying Underground Shotcrete, 6.2

Temperature effects, analysis and design209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, Ch. 1, Ch. 2

224.3R—Joints in Concrete Construction, App. A307—Code Requirements for Reinforced Concrete Chimneys, App. A360R—Design of Slabs-on-Ground, Ch. 12

224R—Control of Cracking in Concrete Structures, 7.3440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, 3.4

Temporary loads, see Construction loads

Tendon, post-tensioning423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons423.7—Specification for Unbonded Single-Strand Tendon Materials

301—Specifications for Structural Concrete, Sec. 9318—Building Code Requirements for Structural Concrete, Ch. 18530—Building Code Requirements for Masonry Structures, Ch. 4


313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 6.4 through 6.7343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.17349—Code Requirements for Nuclear Safety-Related Concrete Structures, 18.16, 18.18350—Code Requirements for Environmental Engineering Concrete Structures, 18.13357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.7372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.6, 4.5440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.3

Tendon tanks, see Water tanks

Tensile strength207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.3212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 4.2213R—Guide for Structural Lightweight-Aggregate Concrete, 4.10, 5.4224.2R—Cracking of Concrete Members in Direct Tension, 3.2325.10R—Report on Roller-Compacted Concrete Pavements, 5.4364.3R—Guide for Cementitious Repair Material Data Sheet, 5.5, 5.6

440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 3.3

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, B.2, B.11549R—Report on Ferrocement, 5.4555R—Removal and Reuse of Hardened Concrete, 5.4

Tension, see also Tensile strength408R—Bond and Development of Straight Reinforcing Bars in Tension408.3R—Guide for Lap Splice and Development Length of High Relative Rib Area Reinforcing Bars in Tension

343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.7355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 7.2440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, L.1, L.2, L.3506.4R—Guide for the Evaluation of Shotcrete, 3.3544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.3

Terminology126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 2, 4.1

SP-15—Field Reference Manual

318—Building Code Requirements for Structural Concrete, Ch. 2332—Code Requirements for Residential Concrete, Ch. 2

440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures, 1.4

Test method, see also Testing214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results350.1—Tightness Testing of Environmental Engineering Concrete Structures364.3R—Guide for Cementitious Repair Material Data Sheet

374.1—Acceptance Criteria for Moment Frames Based on Structural Testing440.3R—Guide Test Methods for Fiber-Reinforced Polymers (FRPs) for Reinforcing or Strengthening Concrete Structures544.2R—Measurement of Properties of Fiber-Reinforced Concrete548.7—Test Method for Load Capacity of Polymer Concrete Underground Utility StructuresT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

228.1R—In-Place Methods to Estimate Concrete Strength, Ch. 2228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures, Ch. 2237R—Self-Consolidating Concrete, Ch. 8238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, Ch. 3, 5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, App. B503R—Use of Epoxy Compounds with Concrete, App. A

506.1R—Guide to Fiber-Reinforced Shotcrete, Ch. 6

222R—Protection of Metals in Concrete Against Corrosion, 4.4224R—Control of Cracking in Concrete Structures, 7.5346—Specification for Cast-in-Place Concrete Pipe, 1.5355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, 5.3548.3R—Report on Polymer-Modified Concrete, 3.2, 3.5

Testing, see also Test method, Evaluation, or Acceptance

214R—Evaluation of Strength Test Results of Concrete214.4R—Guide for Obtaining Cores and Interpreting Compressive Strength Results228.1R—In-Place Methods to Estimate Concrete Strength228.2R—Nondestructive Test Methods for Evaluation of Concrete in Structures374.1—Acceptance Criteria for Moment Frames Based on Structural Testing437.1R—Load Tests of Concrete Structures: Methods, Magnitude, Protocols, and Acceptance CriteriaITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation TestingITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1

MCP INDEX IND-65


207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, Ch. 3, Ch. 4221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, Ch. 6221.1R—Report on Alkali-Aggregate Reactivity, Ch. 4225R—Guide to the Selection and Use of Hydraulic Cements, Ch. 8229R—Controlled Low-Strength Materials, Ch. 7232.2R—Use of Fly Ash in Concrete, App.302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, Ch. 3, Ch. 4, 9.2304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing, Ch. 6304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment, Ch. 6, App. A305R—Hot Weather Concreting, Ch. 5309R—Guide for Consolidation of Concrete, Ch. 17311.4R—Guide for Concrete Inspection, App. I, 3.7311.5—Guide for Concrete Plant Inspection and Testing of Ready-Mixed Concrete, Ch. 2318—Building Code Requirements for Structural Concrete, Ch. 20, 3.1325.10R—Report on Roller-Compacted Concrete Pavements, Ch. 8, 4.4351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, Ch. 4355.2—Qualification of Post-Installed Mechanical Anchors in Concrete, Ch. 5, 7, 8, 9, 12, App. A3363.2R—Guide to Quality Control and Testing of High-Strength Concrete, Ch. 4, Ch. 5364.1R—Guide for Evaluation of Concrete Structures before Rehabilitation, Ch. 5, 2.7, 7.5408R—Bond and Development of Straight Reinforcing Bars in Tension, Ch. 6423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, Ch. 4437R—Strength Evaluation of Existing Concrete Buildings, Ch. 3, 5.2439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities, 3.5440R—Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, Ch. 5440.1R—Guide for the Design and Construction of Concrete Reinforced with FRP Bars, Ch. 5440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, App. B506.5R—Guide for Specifying Underground Shotcrete, Ch, 10, Ch, 11, 8.9523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, Ch. 6522R—Pervious Concrete, Ch. 8524R—Guide to Portland Cement-Based Plaster, Ch. 14549.1R—Guide for the Design, Construction, and Repair of Ferrocement, Ch. 7ITG-4.1—Specification for High-Strength Concrete in Moderate to High Seismic Applications, Sec. 11ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 15, Ch. 16, 17.11, 17.12

201.2R—Guide to Durable Concrete, 5.4, 6.2210R—Erosion of Concrete in Hydraulic Structures, 5.6222.2R—Corrosion of Prestressing Steels, 3.9232.1R—Use of Raw or Processed Natural Pozzolans in Concrete, 3.5301—Specifications for Structural Concrete, 1.6304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 8.4304.2R—Placing Concrete by Pumping Methods, 4.9304.4R—Placing Concrete with Belt Conveyors, 5.2306R—Cold Weather Concreting, 6.2, 6.3307—Code Requirements for Reinforced Concrete Chimneys, 3.3308R—Guide to Curing Concrete, 2.9313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.3, 5.7330.1—Specification for Unreinforced Concrete Parking Lots, 1.6332.1R—Guide to Residential Concrete Construction, 2.6346—Specification for Cast-in-Place Concrete Pipe, 3.4349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.1, 20.1350—Code Requirements for Environmental Engineering Concrete Structures, 3.1, 20.3357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.2360R—Design of Slabs-on-Ground, 3.7363R—Report on High-Strength Concrete, 3.3372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 5.1, 5.4373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 5.1, 5.4423.7—Specification for Unbonded Single-Strand Tendon Materials, 2.6506R—Guide to Shotcrete, 9.8506.4R—Guide for the Evaluation of Shotcrete, 2.2, 2.3, 7.3533R—Guide for Precast Concrete Wall Panels, 7.6, 7.7546.2R—Guide to Underwater Repair of Concrete, 3.5546.3R—Guide for the Selection of Materials for the Repair of Concrete, A.1, A.2555R—Removal and Reuse of Hardened Concrete, 2.2

Texture, see also Pavements303R—Guide to Cast-in-Place Architectural Concrete Practice, 4.6325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 2.2330R—Guide for the Design and Construction of Concrete Parking Lots, 5.5330.1—Specification for Unreinforced Concrete Parking Lots, 3.9345R—Guide for Concrete Highway Bridge Deck Construction, 1.2, 2.7, 10.6524R—Guide to Portland Cement-Based Plaster, 12.3

Thermal effects, see also Temperature207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies

349.1R—Reinforced Concrete Design for Thermal Effects on Nuclear Power Plant Structures


307—Code Requirements for Reinforced Concrete Chimneys, Ch. 6349—Code Requirements for Nuclear Safety-Related Concrete Structures, App. E

213R—Guide for Structural Lightweight-Aggregate Concrete, 5.10343R—Analysis and Design of Reinforced Concrete Bridge Structures, 5.4.4, 8.8360R—Design of Slabs-on-Ground, 13.2364.3R—Guide for Cementitious Repair Material Data Sheet, 5.10

503R—Use of Epoxy Compounds with Concrete, 3.8522.1—Specification for Pervious Concrete Pavement, 3.7530—Building Code Requirements for Masonry Structures, 1.8.3

Thermal properties, see also Properties of concrete

122R—Guide to Thermal Properties of Concrete and Masonry Systems

207.1R—Guide to Mass Concrete, 3.7207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete, 3.5207.5R—Roller-Compacted Mass Concrete, 3.7213R—Guide for Structural Lightweight-Aggregate Concrete, 4.17, 4.18221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 2.4363R—Report on High-Strength Concrete, 5.9440.2R—Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, 4.2523.1R—Guide for Cast-in-Place Low-Density Cellular Concrete, 3.5, 3.8523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 3.3

Thickness, see also Design factors, Deflections325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, Ch. 3

117—Specifications for Tolerances for Concrete Construction and Materials, 13.3216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 3.2, 4.2, App. A through C330R—Guide for the Design and Construction of Concrete Parking Lots, 3.6345R—Guide for Concrete Highway Bridge Deck Construction, 2.3350—Code Requirements for Environmental Engineering Concrete Structures, 14.6, H.3360R—Design of Slabs-on-Ground, 6.2, 7.2, 8.2435R—Control of Deflection in Concrete Structures, 4.4530—Building Code Requirements for Masonry Structures, 5.6

Thin reinforced cement products, see Ferrocement

Thin shells, see Shells

Tilt-up construction551.1R—Tilt-Up Concrete Construction Guide

Ties, see Anchor ties or Forms

Tolerances117—Specifications for Tolerances for Concrete Construction and Materials302.1R—Guide for Concrete Floor and Slab ConstructionSP-15—Field Reference Manual

421.1R—Guide to Shear Reinforcement for Slabs, Ch. 6

210R—Erosion of Concrete in Hydraulic Structures, 5.2230.1R—Report on Soil Cement, 8.7301—Specifications for Structural Concrete, 1.7307—Code Requirements for Reinforced Concrete Chimneys, 3.8313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 3.9, 5.4, 6.14315—Details and Detailing of Concrete Reinforcement, 2.2, 4.3318—Building Code Requirements for Structural Concrete, 7.5325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 3.2330.1—Specification for Unreinforced Concrete Parking Lots, 3.10332.1R—Guide to Residential Concrete Construction, 3.6334.3R—Construction of Concrete Shells Using Inflated Forms, 3.7, 4.18336.1—Specification for the Construction of Drilled Piers, 3.1346—Specification for Cast-in-Place Concrete Pipe, 3.2347—Guide to Formwork for Concrete, 3.3351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 5.5351.2R—Foundations for Static Equipment, 5.2362.1R—Guide for the Design of Durable Parking Structures, 4.3, 4.4371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.1.6372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 4.6373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 4.6506R—Guide to Shotcrete, 8.7506.2—Specification for Shotcrete, 3.12522.1—Specification for Pervious Concrete Pavement, 3.9523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 5.3523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels, 3.4 530.1—Specification for Masonry Structures, 3.3533R—Guide for Precast Concrete Wall Panels, 3.3ITG-7—Specification for Tolerances for Precast Concrete, 2.2, 3.2, 4.2, 5.2

Toppings, see Overlays, Finishing

Torsion, see also Shear strength318—Building Code Requirements for Structural Concrete, Ch. 11

MCP INDEX IND-67

350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 11

343R—Analysis and Design of Reinforced Concrete Bridge Structures, 9.15349—Code Requirements for Nuclear Safety-Related Concrete Structures, 11.6358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 6.3

Toughness, see also Properties544.2R—Measurement of Properties of Fiber-Reinforced ConcreteT1.2—Special Hybrid Moment Frames Composed of Discretely Jointed Precast and Post-Tensioned Concrete Members

374.1—Acceptance Criteria for Moment Frames Based on Structural Testing, 2.6544.4R—Design Considerations for Steel Fiber-Reinforced Concrete, 2.5

Tower, see Cooling tower

Towing357.2R—Report on Barge-Like Concrete Structures, Ch. 7

357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 6.10

Tracks, see Guideways

Traffic325.11R—Accelerated Techniques for Concrete Paving, Ch. 7

325.12R—Guide for Design of Jointed Concrete Pavements for Streets and Local Roads, 3.2

Training, see Certification

Transit, see Guideways

Transporting concrete, see also Conveying304.2R—Placing Concrete by Pumping Methods304.3R—Heavyweight Concrete: Measuring, Mixing, Transporting, and Placing

229R—Controlled Low-Strength Materials, Ch. 6237R—Self-Consolidating Concrete, Ch. 6, 6.2304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, Ch. 4

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, 11.7207.5R—Roller-Compacted Mass Concrete, 5.4213R—Guide for Structural Lightweight-Aggregate Concrete, 3.5222.3R—Design and Construction Practices to Mitigate Corrosion of Reinforcement in Concrete Structures, 4.1234R—Guide for the Use of Silica Fume in Concrete, 9.1, 9.3302.1R—Guide for Concrete Floor and Slab Construction, 7.3

311.6—Specification for Ready Mixed Concrete Testing Services, 2.5.2325.10R—Report on Roller-Compacted Concrete Pavements, 7.3330.1—Specification for Unreinforced Concrete Parking Lots, 3.5345R—Guide for Concrete Highway Bridge Deck Construction, 9.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 16.9363R—Report on High-Strength Concrete, 4.4543R—Design, Manufacture, and Installation of Concrete Piles, 4.5544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 7.3ITG-4.2R—Materials and Quality Considerations for High-Strength Concrete in Moderate to High Seismic Applications, 8.2

Tremie concrete, see also Placing concrete304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 8.5546.2R—Guide to Underwater Repair of Concrete, 6.3

Trench backfill, see also Controlled low-strength materials

229R—Controlled Low-Strength Materials, 2.2, 6.4346—Specification for Cast-in-Place Concrete Pipe, 3.1

Troubleshooting, see Repair

Truck-mounted pumps, see also Pumping304.2R—Placing Concrete by Pumping Methods, 2.4

Truss model, see also Strut-and-tie models445R—Recent Approaches to Shear Design of Structural Concrete, Ch. 3, 2.5

Tunnels224R—Control of Cracking in Concrete Structures, Ch. 7

210R—Erosion of Concrete in Hydraulic Structures, 3.4309R—Guide for Consolidation of Concrete, 8.5

Two-way slabs, see also Slabs421.1R—Guide to Shear Reinforcement for Slabs

318—Building Code Requirements for Structural Concrete, Ch. 13350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 13209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 2.7347.2R—Guide for Shoring/Reshoring of Concrete Multistory Buildings, 5.1

Ultimate strength, see also Strength design, Structural design

213R—Guide for Structural Lightweight-Aggregate Concrete, 4.13


Unbonded prestressing, see also Prestressing, Post-tensioning

423.7—Specification for Unbonded Single-Strand Tendon Materials

440.4R—Prestressing Concrete Structures with FRP Tendons, Ch. 7222.2R—Corrosion of Prestressing Steels, 7.4423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 2.3423.4R—Corrosion and Repair of Unbonded Single-Strand Tendons, 2.4

Underground structures548.7—Test Method for Load Capacity of Polymer Concrete Underground Utility Structures

Underwater repair, see also Repair546.2R—Guide to Underwater Repair of Concrete

546R—Concrete Repair Guide, 3.2.10548.1R—Guide for the Use of Polymers in Concrete, 3.7.5.6

Unreinforced concrete360R—Design of Slabs-on-Ground, Ch. 6

Unreinforced masonry530—Building Code Requirements for Masonry Structures, 2.2

Vapor retarder/barrier302.2R—Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials, Ch. 7, 9.3

Vehicle loads, see Loads

Veneers530—Building Code Requirements for Masonry Structures, Ch. 6

Vertical alignment, see Tolerances

Vertical clearance, see Tolerances

Vibration, see also Consolidation309R—Guide for Consolidation of Concrete

309.1R—Report on Behavior of Fresh Concrete During Vibration, Ch. 4309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, Ch. 4

207.3R—Practices for Evaluation of Concrete in Existing Massive Structures for Service Conditions, 3.3210R—Erosion of Concrete in Hydraulic Structures, 5.4345.2R—Guide for Widening Highway Bridges, 3.4358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 5.6

Vibration frequency351.3R—Foundations for Dynamic Equipment

350.4R—Design Considerations for Environmental Engineering Concrete Structures, 4.5

Void filling, see also Repair229R—Controlled Low-Strength Materials, 2.8

Voids, see also Surface defects309.2R—Identification and Control of Visible Effects of Consolidation on Formed Concrete Surfaces, 3.2506.5R—Guide for Specifying Underground Shotcrete, 8.5

Volume change207.2R—Report on Thermal and Volume Change Effects on Cracking of Mass Concrete

207.1R—Guide to Mass Concrete, 3.5207.5R—Roller-Compacted Mass Concrete, 3.6351.1R—Grouting between Foundations and Bases for Support of Equipment and Machinery, 2.2

Volumetric, see also Batching, Yield304.6R—Guide for Use of Volumetric-Measuring and Continuous-Mixing Concrete Equipment

211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, 3.3, 4.3

Wall thickness, see Tolerances

Walls, see also Shearwalls523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units523.4R—Guide for Design and Construction with Autoclaved Aerated Concrete Panels524—Guide to Portland Cement-Based Plaster533R—Guide for Precast Concrete Wall Panels551.1R—Tilt-Up Concrete Construction GuideITG-5.1—Acceptance Criteria for Special Unbonded Post-Tensioned Precast Structural Walls Based on Validation TestingITG-5.2—Requirements for Design of a Special Unbonded Post-Tensioned Precast Shear Wall Satisfying ACI ITG-5.1

122R—Guide to Thermal Properties of Concrete and Masonry Systems, Ch. 3, Ch. 4, Ch. 6318—Building Code Requirements for Structural Concrete, Ch. 14, 11.9, 15.8, 21.4, 21.9, 21.10, 22.6332—Code Requirements for Residential Concrete, Ch. 7, App. A332.1R—Guide to Residential Concrete Construction, Ch. 4349—Code Requirements for Nuclear Safety-Related Concrete Structures, Ch. 14, 11.10, 15.8 350—Code Requirements for Environmental Engineering Concrete Structures, Ch. 14, 11.10, 21.7ITG-4.3R—Report on Structural Design and Detailing for High-Strength Concrete in Moderate to High Seismic Applications, Ch. 9

MCP INDEX IND-69

216.1—Code Requirements for Determining Fire Resistance of Concrete and Masonry Construction Assemblies, 2.2, 3.3, 4.3223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 3.7224.3R—Joints in Concrete Construction, 8.2303R—Guide to Cast-in-Place Architectural Concrete Practice, 3.7313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 4.5, 5.5, 6.10, 7.5315—Details and Detailing of Concrete Reinforcement, 2.10346—Specification for Cast-in-Place Concrete Pipe, 3.2371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 4.3.1.2, 5.2.2.5, 5.4.1.4 372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 2.3373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.6, 3.3423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 3.7530—Building Code Requirements for Masonry Structures, 1.9, 2.1, 5.3, 5.6 through 5.8

Warping, see also Slab-on-ground, Tolerances201.1R—Guide for Conducting a Visual Inspection of Concrete in Service, 2.2.21209R—Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, 3.6360R—Design of Slabs-on-Ground, 13.3, 13.12, 13.13435R—Control of Deflection in Concrete Structures, 4.3

Waste containment, see also Containment232.2R—Use of Fly Ash in Concrete, 8.8

Water, see also Mixture proportioning212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete

346—Specification for Cast-in-Place Concrete Pipe, Ch. 3,

126.3R—Guide to a Recommended Format for Concrete in a Materials Property Database, Ch. 10308.1—Standard Specification for Curing Concrete, Ch. 4 through Ch. 7

207.1R—Guide to Mass Concrete, 2.6207.4R—Cooling and Insulating Systems for Mass Concrete, 2.3211.3R—Guide for Selecting Proportions for No-Slump Concrete, 2.3, 3.3213R—Guide for Structural Lightweight-Aggregate Concrete, 4.15223—Standard Practice for the Use of Shrinkage-Compensating Concrete, 2.3229R—Controlled Low-Strength Materials, 3.6230.1R—Report on Soil Cement, 4.7234R—Guide for the Use of Silica Fume in Concrete, 3.5, 4.1238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete, 4.3302.1R—Guide for Concrete Floor and Slab Construction, 5.5304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 3.5, 4.5.3

304.2R—Placing Concrete by Pumping Methods, 4.4305R—Hot Weather Concreting, 2.4306R—Cold Weather Concreting, 3.3308R—Guide to Curing Concrete, 2.2, 2.3309R—Guide for Consolidation of Concrete, 10.6313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 2.4318—Building Code Requirements for Structural Concrete, 3.4325.10R—Report on Roller-Compacted Concrete Pavements, 3.4325.11R—Accelerated Techniques for Concrete Paving, 4.8345R—Guide for Concrete Highway Bridge Deck Construction, 8.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.4350—Code Requirements for Environmental Engineering Concrete Structures, 3.4357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, 2.6506R—Guide to Shotcrete, 2.5506.2—Specification for Shotcrete, 2.4523.2R—Guide for Precast Cellular Concrete Floor, Roof, and Wall Units, 2.4524R—Guide to Portland Cement-Based Plaster, 4.5555R—Removal and Reuse of Hardened Concrete, 3.1

Water tanks, see also Environmental engineering

350.2R—Concrete Structures for Containment of Hazardous Materials350.3—Seismic Design of Liquid-Containing Concrete Structures371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons

Water towers, see Water tanks

Water-borne adhesives, see also Adhesives503.5R—Guide for the Selection of Polymer Adhesives with Concrete, Ch. 3

Water-cement ratio, see also Water-cementitious material ratio, Mixture proportioning

211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, 3.5211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, 2.3363R—Report on High-Strength Concrete, 3.4555R—Removal and Reuse of Hardened Concrete, 5.5

Water-cementitious material ratio, see also Water-cement ratio, Mixture proportioning

211.3R—Guide for Selecting Proportions for No-Slump Concrete, 3.4


211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, Ch. 6 through 8, 3.2, 5.2212.4R—Guide for the Use of High-Range Water-Reducing Admixtures (Superplasticizers) in Concrete, 3.2301—Specification for Structural Concrete, 4.2.2318—Building Code Requirements for Structural Concrete, 4.1349—Code Requirements for Nuclear Safety-Related Concrete Structures, 4.1350—Code Requirements for Environmental Engineering Concrete Structures, 4.1

Waterproof coating, see also Liners, Waterproofing, or Protective coatings

350.1—Tightness Testing of Environmental Engineering Concrete Structures

222R—Protection of Metals in Concrete Against Corrosion, Ch. 3

Waterproofing, see also Protective coatings503R—Use of Epoxy Compounds with Concrete, 4.2

Water-reducing admixtures, see Admixtures

Waterstop350.2R—Concrete Structures for Containment of Hazardous Materials, 3.1372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, 3.6, 4.8373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, 2.7, 4.8

Watertightness372R—Design and Construction of Circular Wire- and Strand-Wrapped Prestressed Concrete Structures, Ch. 5373R—Design and Construction of Circular Prestressed Concrete Structures with Circumferential Tendons, Ch. 5

309.5R—Compaction of Roller-Compacted Concrete, 3.3

Wave loads, see also Loads350.3—Seismic Design of Liquid-Containing Concrete Structures, Ch. 7357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, App. A

Wear, see Abrasion

Wear resistance, see also Abrasion resistance302.1R—Guide for Concrete Floor and Slab Construction, 11.3

Welded-wire reinforcement315—Details and Detailing of Concrete Reinforcement

301—Specification for Structural Concrete, Sec. 3

318—Building Code Requirements for Structural Concrete, 12.7, 12.8, 12.18, 12.19

349—Code Requirements for Nuclear Safety-Related Concrete Structures, 12.7, 12.8, 12.18, 12.19350—Code Requirements for Environmental Engineering Concrete Structures, 12.7, 12.8, 12.18, 12.19

Welding301—Specifications for Structural Concrete, Sec. 3

318—Building Code Requirements for Structural Concrete, 3.5349—Code Requirements for Nuclear Safety-Related Concrete Structures, 3.5350—Code Requirements for Environmental Engineering Concrete Structures, 3.5423.3R—Recommendations for Concrete Members Prestressed with Unbonded Tendons, 5.7439.4R—Report on Steel Reinforcement—Material Properties and U.S. Availabilities, 3.4

Wind loads, see also Loads307—Code Requirements for Reinforced Concrete Chimneys, 4.2313—Standard Practice for Design and Construction of Concrete Silos and Stacking Tubes for Storing Granular Materials, 4.4.7318—Building Code Requirements for Structural Concrete, 8.2334.3R—Construction of Concrete Shells Using Inflated Forms, 3.15343R—Analysis and Design of Reinforced Concrete Bridge Structures, 5.5.1347—Guide to Formwork for Concrete, 2.2349—Code Requirements for Nuclear Safety-Related Concrete Structures, 8.2357R—Guide for the Design and Construction of Fixed Offshore Concrete Structures, A.8358.1R—Analysis and Design of Reinforced and Prestressed Concrete Guideway Structures, 3.3.2371R—Guide for the Analysis, Design, and Construction of Elevated Concrete and Composite Steel-Concrete Water Storage Tanks, 5.1.2.6530—Building Code Requirements for Masonry Structures, 1.7

Wire Reinforcement Institute (WRI) method, see also Slabs

360R—Design of Slabs-on-Ground, App. 2

Wire-wrapped structures, see Water tanks

Workability238.1R—Report on Measurements of Workability and Rheology of Fresh Concrete309.1R—Report on Behavior of Fresh Concrete During Vibration, Ch. 2544.2R—Measurement of Properties of Fiber-Reinforced Concrete, Ch. 2

207.5R—Roller-Compacted Mass Concrete, 2.3.1211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, Ch. 4, 5.3, 7.1.1.4221R—Guide for Use of Normal Weight and Heavyweight Aggregates in Concrete, 3.3

MCP INDEX IND-71

225R—Guide to the Selection and Use of Hydraulic Cements, 6.2233R—Slag Cement in Concrete and Mortar, 4.1234R—Guide for the Use of Silica Fume in Concrete, 4.2309R—Guide for Consolidation of Concrete, 2.2, 2.3330R—Guide for the Design and Construction of Concrete Parking Lots, 4.5363R—Report on High-Strength Concrete, 3.8544.3R—Guide for Specifying, Proportioning, and Production of Fiber-Reinforced Concrete, 4.3548.3R—Report on Polymer-Modified Concrete, 4.1.3.2.2

Yield, as in volume229R—Controlled Low-Strength Materials, Ch. 5

211.1—Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, 6.3

211.2—Standard Practice for Selecting Proportions for Structural Lightweight Concrete, 3.2211.4R—Guide for Selecting Proportions for High-Strength Concrete Using Portland Cement and Other Cementitious Materials, Ch. 8, 6.2.3.10211.5R—Guide for Submittal of Concrete Proportions, 3.3213R—Guide for Structural Lightweight-Aggregate Concrete, 3.4.2304R—Guide for Measuring, Mixing, Transporting, and Placing Concrete, 3.3.4304.6R—Guide for Use of Volumetric-Measuring and

Continuous-Mixing Concrete Equipment, 6.2

Yield strength, see also Reinforcement – steel, Prestressing steel

437R—Strength Evaluation of Existing Concrete Buildings, 3.2.2

64033854-ACI-MANUAL-OF-CONCRETE-PRACTICE-INDEXâ€”2010

Documents

Transcript of 64033854-ACI-MANUAL-OF-CONCRETE-PRACTICE-INDEXâ€”2010