626 Ltd - dafra.co.uk 4210.pdf · FOR USE WITH CORDLESS DRILL-DRIVERS MAX 400 RPM ONLY. USING THIS...
1
OPERATING INSTRUCTIONS Rivnut tool that attaches to a standard cordless drill driver fmax 9"" RPMg2 The tool kit contains: V mandrels and anvilsw sizes M9 MV M- MK A MD" Spanner A Allen key for changing mandrels and anvils -" piece rivnut kit Plastic storage case D2 Fit the correct size anvil and mandrel for the chosen Rivnut to the tool2 To change the mandrel and anvil2 Unscrew the silver nose piece from the front of the toolw remove grub screw located in the drive piston2 Use the spanner provided to unscrew the mandrel2 Fit new mandrel and replace grub screw2 Unscrew anvil from silver nose piece and replace with anvil matching the installed mandrel2 Re fit spring and silver nose piece2 C2 Fit the adaptor hex drive into the drill chuck and tighten2 H2 Select drill reverse and hold adaptor body to stop it from spinningw reverse drill until you hear the adaptor &click& as an indication that the tool is ready to take a rivnut2 92 Select drill forwardw let the adaptor spinw thread rivnut onto the mandrel2 STOP WHEN THE MANDREL IS LEVEL WITH THE TOP OF THE RIVNUT LEAVING A GAP BETWEEN THE RIVNUT AND THE TOOL ANVIL . SEE PICTURE. V2 Place Rivnut into prepared holew hold adaptor to stop it from spinningw run drill in forwardw until the Rivnut is tight against the sheet2 DO NOT OVERTIGHTEN. -2 Select drill reversew let the adaptor spin out of the rivnutw once free hold the adaptor so that the mandrel screws forward until you hear the adaptor &click& Dimensions Capacity Hex Shank Cordless Drill Max rpm VL x DK" mm M9 MV M- MK MD" D929V b DKV 9""rpm Technical Data FOR USE WITH CORDLESS DRILL-DRIVERS MAX 400 RPM ONLY. USING THIS TOOL WITH IMPACT DRIVERS OR COMBINATION HAMMER DRILL DRIVERS WILL VOID ANY WARRANTY. Tool weight HH"g Aluminium Steel Stainless Steel Rivnut MV M- MK MD" M9 K mm Part number: DRNCA9CD" Cordless Rivnut adapter www2dafra2co2uk Capacity chart afra UK2 D Ltd
Transcript of 626 Ltd - dafra.co.uk 4210.pdf · FOR USE WITH CORDLESS DRILL-DRIVERS MAX 400 RPM ONLY. USING THIS...
OPERATING INSTRUCTIONS
6
Rivnut6tool6that6attaches6to6a6standardcordless6drill6driver6fmax69""6RPMg2
The6tool6kit6contains:6666V6mandrels6and6anvilsw6sizes6M96MV6M-6MK6A6MD"6666Spanner6A6Allen6key6for6changing6mandrels6and6anvils6666-"6piece6rivnut6kit6666Plastic6storage6case
D26Fit6the6correct6size6anvil6and6mandrel6for6the6chosen6Rivnut6to6the6tool2To6change6the6mandrel6and6anvil26Unscrew6the6silver6nose6piece6from6the6front6of6the6toolwremove66grub6screw6located6in6the6drive6piston26Use6the6spanner6provided6to6unscrew6themandrel26Fit6new6mandrel6and6replace6grub6screw26Unscrew6anvil6from6silver6nose6piece6andreplace6with6anvil6matching6the6installed6mandrel26Re6fit6spring6and6silver6nose6piece26C26Fit6the6adaptor6hex6drive6into6the6drill6chuck6and6tighten2H26Select6drill6reverse6and6hold6adaptor6body6to6stop6it6from6spinningw6reverse6drill6until666you6hear6the6adaptor6&click&6as66an6indication6that6the6tool6is6ready6to6take6a6rivnut26
926Select6drill6forwardw6let6the6adaptor6spinw6thread6rivnut6onto6the6mandrel2 STOP WHEN THE MANDREL IS LEVEL WITH THE TOP OF THE RIVNUT LEAVING A GAP BETWEEN THE RIVNUT AND THE TOOL ANVIL . SEE PICTURE.6V26Place6Rivnut6into6prepared6holew6hold6adaptor6to6stop6it6from6spinningw6run6drill6in6666forwardw6until6the6Rivnut6is6tight6against6the6sheet26DO NOT OVERTIGHTEN.-26Select6drill6reversew6let6the6adaptor6spin6out6of6the6rivnutw6once6free6hold6the6adaptor666so6that6the6mandrel6screws6forward6until6you6hear6the6adaptor6&click&666
Dimensions
Capacity
Hex6Shank
Cordless6Drill
Max6rpm
VL6x6DK"6mm
M96MV6M-6MK6MD"
D929V66b666DKV
9""rpm
Technical6Data
FOR USE WITH CORDLESS DRILL-DRIVERS MAX 400 RPM ONLY.USING THIS TOOL WITH IMPACT DRIVERS OR COMBINATIONHAMMER DRILL DRIVERS WILL VOID ANY WARRANTY.
Tool6weight HH"g
Aluminium
Steel
Stainless6Steel
Rivnut MV M- MK MD"M9
K6mm
Part6number:6DRNCA9CD"Cordless6Rivnut6adapter
www2dafra2co2uk
Capacity6chart
afra6UK26DD Ltd
