500-370art - Channel Vision · PDF file100 Watt integrated class D amplifier ... ARIA’S...

A0915iBus Wall-Dock Single Room Kit

• Intelligent Entertainment • Infrastructure • Security Solutions

TM By CHANNEL VISION

Local InActiveSpkrs 24VDCIR In

Flush Mount Amplifier

Simplify your installation with ARIA Audio Systems single zone audio package. This single zone iPod® audio package allows you to customize individual rooms to give anyone in condos, hotels, dorm rooms, and bedrooms control over their own iPod in their own space. The A0915 Kit includes the iBus Wall Dock for iPod, 100W Amplifier, Keypad controller, and one pair of 6.5" architectural speakers.

Features:!

!Pre-amp audio outputs for easy connection to powered subwoofer!Local audio input !Easy installation!iPod Dock included!Speakers included

100 Watt integrated class D amplifier

Included ProductsProduct Introduction

A0129:IR repeating keypad.volume control on the A0350. You may also use a standard IR receiver such as the IR-2400. When using a simple IR receiver, you will need to use the A0505 remote control which contains the IR codes to control the A0350. IR codes can be downloaded from www.channelvision.com, or learned from an A0505 remote control.

The A0129 contains the IR codes to operate the

A0350:100 watt (50 watt per channel) amplifier.The A0350 has an audio output (RCA) on the back, as well as a local (RCA) audio input on the front.Speaker outputs can be used on either the front or the back. A 24vDC 4 Amp power supply is included with this amplifier.

A0315:The A0315 is an on-wall iPod® docking station for CAT5 audio systems. The dock connector slides in and out to adjust for any iPod and the nonskid pad helps to hold the music player in place. The A0315’s elegant and contemporary styling make it the perfect choice for anyone who wants to enjoy their music without defacing their wall.

IC608:ARIA’S Builder Series 120 watt 6.5″ In-Ceiling Speakers are designed for economical sound system installations.

Pwr Mute

Flush Mount Amplifier1. Read these instructions.

2. Keep these instructions for future reference.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this device near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with these instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. This apparatus must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Unplug this apparatus during lightning storms or when unused for long periods of time

Warning: To reduce the risk of electric shock, do not remove the cover (or back), no user serviceable parts inside, refer servicing to qualified service personnel.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN!

Simplify your installation with ARIA Audio Systems single zone audio package. This single zone iPod® audio package allows you to customize individual rooms to give anyone in condos, hotels, dorm rooms, and bedrooms control over their own iPod in their own space. The A0915 Kit includes the iBus Wall Dock for iPod, 100W Amplifier, Keypad controller, and one pair of 6.5" architectural speakers.

Features:!

!Pre-amp audio outputs for easy connection to powered subwoofer!Local audio input !Easy installation!iPod Dock included!Speakers included

100 Watt integrated class D amplifier

Included ProductsProduct Introduction

A0129:IR repeating keypad.volume control on the A0350. You may also use a standard IR receiver such as the IR-2400. When using a simple IR receiver, you will need to use the A0505 remote control which contains the IR codes to control the A0350. IR codes can be downloaded from www.channelvision.com, or learned from an A0505 remote control.

The A0129 contains the IR codes to operate the

A0350:100 watt (50 watt per channel) amplifier.The A0350 has an audio output (RCA) on the back, as well as a local (RCA) audio input on the front.Speaker outputs can be used on either the front or the back. A 24vDC 4 Amp power supply is included with this amplifier.

A0315:The A0315 is an on-wall iPod® docking station for CAT5 audio systems. The dock connector slides in and out to adjust for any iPod and the nonskid pad helps to hold the music player in place. The A0315’s elegant and contemporary styling make it the perfect choice for anyone who wants to enjoy their music without defacing their wall.

IC608:ARIA’S Builder Series 120 watt 6.5″ In-Ceiling Speakers are designed for economical sound system installations.

Pwr Mute

Flush Mount Amplifier1. Read these instructions.

2. Keep these instructions for future reference.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this device near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with these instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. This apparatus must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Unplug this apparatus during lightning storms or when unused for long periods of time

Warning: To reduce the risk of electric shock, do not remove the cover (or back), no user serviceable parts inside, refer servicing to qualified service personnel.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN!

Installation

A0350 InstallationThe A0350 can be installed in the wall using a standard 2-gang junction box or low-voltage mounting ring.

Installing the A0315 Trim Plate AccessoryFollow the diagram below to install the trim plate accessory that is included with the A0315 iPod dock.

In-Wall InstallationStandard 2-gang ring or extra deep

j-box (not included)Attach unit with the provided screws

Note: if using a j-box, it must have a minimum

depth of 3.5”TM By CHANNEL VISION

Local InActiveSpkrs24VDCIR In

Take care not to pinch wires when installing

into 2-gang box.

Install Outputwall plate in j-box

Install Trim plate chassisover output wall plate

Snap front cover over chassis

Snap side flange on to front cover

Snap trim into place

Installation Continued

A0315 1. Connect all wiring.2. Attach main chassis to j-box using the provided four 6-32 screws.3. Feed the dock connector circuit board through the opening in the front cover.4. Hang the front cover on the main chassis from the two top tabs.5. Secure the front cover with the two small screws at the bottom.6. Place the dock platform over the slide rail and push downward until the retention snaps are engaged.7. Slide the side protectors into the slots on the main chassis.

Installation Steps

Retention Snap

Slide Rail

Completed Installation

Steps 3 & 4 complete

Installation

A0350 InstallationThe A0350 can be installed in the wall using a standard 2-gang junction box or low-voltage mounting ring.

Installing the A0315 Trim Plate AccessoryFollow the diagram below to install the trim plate accessory that is included with the A0315 iPod dock.

In-Wall InstallationStandard 2-gang ring or extra deep

j-box (not included)Attach unit with the provided screws

Note: if using a j-box, it must have a minimum

depth of 3.5”TM By CHANNEL VISION

Local InActiveSpkrs24VDCIR In

Take care not to pinch wires when installing

into 2-gang box.

Install Outputwall plate in j-box

Install Trim plate chassisover output wall plate

Snap front cover over chassis

Snap side flange on to front cover

Snap trim into place

Installation Continued

A0315 1. Connect all wiring.2. Attach main chassis to j-box using the provided four 6-32 screws.3. Feed the dock connector circuit board through the opening in the front cover.4. Hang the front cover on the main chassis from the two top tabs.5. Secure the front cover with the two small screws at the bottom.6. Place the dock platform over the slide rail and push downward until the retention snaps are engaged.7. Slide the side protectors into the slots on the main chassis.

Installation Steps

Retention Snap

Slide Rail

Plug intoCAT5 output on back of A0315

Plug intoCAT5 audio input on back of A0315

Plug intokeypad inputon backof A0350

See attachment detail on previous page

Installation Steps1. Connect all wiring. Use the correct installation tools: J-110 tool, or 1014 crimp tool.2. Install keypad and single-gang trim plate in the far left position of the 3-gang junction box. (See details on page 3)3. Leave off the right side flange and trim piece. 4. Install the iPod dock in the left side of the 3-gang j-box. It will overlap and snap into the single gang trim plate. (See page 5 for details)

Installation Continued Basic System Diagram

The A0350 can be flush-mounted in a room to power in-wall speakers. By connecting the audio outputs from an audio source to the RCA inputs of the A0350, the audio signal will be amplified to the in-wall speakers. Most audio sources only offer a fixed audio output, A0350 volume level can be adjusted by using an A0129 keypad or by connecting an IR-2400 and using a compatible remote such as model A0505. The RCA audio outputs on the back of the A0350 can be connected to a powered subwoofer to add more bass to your audio system. Connect the A0315 to the CAT5 input on the back of the A0350. Plug the A0129 into the back of the keypad input on the back of the A0350.

Pwr Mute

CD player

In some installations it may be desirable to mount a single gang control keypad next to the A0315. To accomplish this, the single gang trim plate can be installed next to the A0315 in a 3-gang junction box.Follow the steps below:

Plug intoCAT5 output on back of A0315

Plug intoCAT5 audio input on back of A0315

Plug intokeypad inputon backof A0350

See attachment detail on previous page

Installation Steps1. Connect all wiring. Use the correct installation tools: J-110 tool, or 1014 crimp tool.2. Install keypad and single-gang trim plate in the far left position of the 3-gang junction box. (See details on page 3)3. Leave off the right side flange and trim piece. 4. Install the iPod dock in the left side of the 3-gang j-box. It will overlap and snap into the single gang trim plate. (See page 5 for details)

Installation Continued Basic System Diagram

The A0350 can be flush-mounted in a room to power in-wall speakers. By connecting the audio outputs from an audio source to the RCA inputs of the A0350, the audio signal will be amplified to the in-wall speakers. Most audio sources only offer a fixed audio output, A0350 volume level can be adjusted by using an A0129 keypad or by connecting an IR-2400 and using a compatible remote such as model A0505. The RCA audio outputs on the back of the A0350 can be connected to a powered subwoofer to add more bass to your audio system. Connect the A0315 to the CAT5 input on the back of the A0350. Plug the A0129 into the back of the keypad input on the back of the A0350.

Pwr Mute

CD player

In some installations it may be desirable to mount a single gang control keypad next to the A0315. To accomplish this, the single gang trim plate can be installed next to the A0315 in a 3-gang junction box.Follow the steps below:

Problem: Hum in System

Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away. Try lifting the ground with a ground lifting plug.

Cause: The different components in the system are connected to different electrical grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz hum.

Solution: Plug products into an electrical circuit with a common ground.

Problem: CAT5 audio input (iPod dock) is not working

Troubleshooting: Verify you have plugged the CAT5 into the output on the back of the A0315. Verify you have plugged the CAT5 into the terminal labeled audio input on the back of the A0350.

Cause: iPod dock not connected properly, wire crimped improperly or plugged into the wrong terminal.

Solution: Verify wiring, verify RJ-45 crimps,

Problem: RCA Audio input is not working.

Troubleshooting: Verify source audio is playing, or try another audio sourceAdjust sensitivity knob on bottom of A0350. Check speaker wires to verify nothing is backwards or crossed.

Cause: There is no signal (or very weak signal) coming from the source, or source is not compatible with A0350.

Solution: Make sure the source audio is playing. Turn the sensitivity knob on the bottom of the A0350 clockwise or counter clockwise to adjust input for sources that are provided a weak level output.

Problem: A0129 not controlling volume

Troubleshooting: Make sure there is a strong and constant signal coming from the iPod dock or audio source. if an iPod, try a different song. If the RCA input is being used, try a different source or adjust the audio level of the source. Verify the right and left audio trim pots on the bottom of the A0350 are close to all the way up.

Cause: There is no signal (or very weak signal) coming from the source, or the audio level feeding into the A0350 is too low. It is possible the A0129 is wired incorrectly.

Solution: Verify wiring, verify RJ-45 crimps, verify connection on the back of the A0129.

Problem: A0350 is now powering on

Troubleshooting: Verify wiring, test the 24vDC power supply that came with the A0350.

Cause: The power supply is plugged in incorrectly or is not functioning properly.

Solution: Verify power supply voltage with a volt meter, verify polarity if using the side power connection on the A0350.

Troubleshooting Troubleshooting Continued

Problem: iPod not charging

Cause: iPod dock not connected properly, wire crimped improperly or plugged into the wrong terminal, iPod too old (not compatible) or has a very worn outconnector that is not making a good connection to the A0315 dock.

Solution: Verify wiring, verify RJ-45 crimps, try a different iPod

Problem: Hum in System

Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away. Try lifting the ground with a ground lifting plug.

Cause: The different components in the system are connected to different electrical grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz hum.

Solution: Plug products into an electrical circuit with a common ground.

Problem: CAT5 audio input (iPod dock) is not working

Cause: iPod dock not connected properly, wire crimped improperly or plugged into the wrong terminal.

Solution: Verify wiring, verify RJ-45 crimps,

Problem: RCA Audio input is not working.

Troubleshooting: Verify source audio is playing, or try another audio sourceAdjust sensitivity knob on bottom of A0350. Check speaker wires to verify nothing is backwards or crossed.

Cause: There is no signal (or very weak signal) coming from the source, or source is not compatible with A0350.

Solution: Make sure the source audio is playing. Turn the sensitivity knob on the bottom of the A0350 clockwise or counter clockwise to adjust input for sources that are provided a weak level output.

Problem: A0129 not controlling volume

Troubleshooting: Make sure there is a strong and constant signal coming from the iPod dock or audio source. if an iPod, try a different song. If the RCA input is being used, try a different source or adjust the audio level of the source. Verify the right and left audio trim pots on the bottom of the A0350 are close to all the way up.

Cause: There is no signal (or very weak signal) coming from the source, or the audio level feeding into the A0350 is too low. It is possible the A0129 is wired incorrectly.

Solution: Verify wiring, verify RJ-45 crimps, verify connection on the back of the A0129.

Problem: A0350 is now powering on

Troubleshooting: Verify wiring, test the 24vDC power supply that came with the A0350.

Cause: The power supply is plugged in incorrectly or is not functioning properly.

Solution: Verify power supply voltage with a volt meter, verify polarity if using the side power connection on the A0350.

Troubleshooting Troubleshooting Continued

Problem: iPod not charging

Cause: iPod dock not connected properly, wire crimped improperly or plugged into the wrong terminal, iPod too old (not compatible) or has a very worn outconnector that is not making a good connection to the A0315 dock.

Solution: Verify wiring, verify RJ-45 crimps, try a different iPod

A0350 Specifications: (typical at 77 )

Amplifier: Power input: 24VDC 4 AmpsOutput power: 50 Watts/ch RMS into 6 ohms @ <10% THDFrequency Response: 20-20kHz (+/-3dB)Signal to Noise Ratio: >85dBInput Sensitivity: 500mVRMSAuto On Threshold: 10mVRMS

Storage Temperature: -40 to +85º COperating temperature: 0 to +55º C

*Specifications subject to change without notice

A0315 Specifications: (typical at 77º)

Operating Voltage : 15VDC (provided by A0350)

Cable Requirements: CAT5 or better

Operating Temperature: -10ºC to +50ºC

IC608 Specifications: (typical at 77º)

Frequency range: 60Hz - 20kHz ± 3dB

Power Handling: 120 Watts

Drivers: 1- 0.5” High compliance polymer

1- 6.5” Polypropylene woofer

Impedance: 8 ohms

Finish: ABS plastic

Dimensions: 9” OD. 3.15 Hole size: 7.7”

Specifications

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

!Reorient or relocate the receiving antenna. !Increase the separation between the equipment and receiver. !Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. !Consult the dealer or an experienced radio/TV technician for help. !Modifications not expressly approved by the manufacturer could void the user's

authority to operated the equipment under FCC rules.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Certifications

Green/White - Left Channel Audio GroundGreen - Left Channel Audio Orange/White - Right Channel Audio GroundBlue - IR SignalBlue/White - StatusOrange- Right Channel Audio

Brown/White 24vDC GroundBrown 24vDC

Top view:

Pin-out

A0350 Specifications: (typical at 77 )

Amplifier: Power input: 24VDC 4 AmpsOutput power: 50 Watts/ch RMS into 6 ohms @ <10% THDFrequency Response: 20-20kHz (+/-3dB)Signal to Noise Ratio: >85dBInput Sensitivity: 500mVRMSAuto On Threshold: 10mVRMS

Storage Temperature: -40 to +85º COperating temperature: 0 to +55º C

*Specifications subject to change without notice

IC608 Specifications: (typical at 77º)

Frequency range: 60Hz - 20kHz ± 3dB

Power Handling: 120 Watts

Drivers: 1- 0.5” High compliance polymer

1- 6.5” Polypropylene woofer

Impedance: 8 ohms

Finish: ABS plastic

Dimensions: 9” OD. 3.15 Hole size: 7.7”

Specifications

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

!Reorient or relocate the receiving antenna. !Increase the separation between the equipment and receiver. !Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. !Consult the dealer or an experienced radio/TV technician for help. !Modifications not expressly approved by the manufacturer could void the user's

authority to operated the equipment under FCC rules.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Certifications

Green/White - Left Channel Audio GroundGreen - Left Channel Audio Orange/White - Right Channel Audio GroundBlue - IR SignalBlue/White - StatusOrange- Right Channel Audio

Brown/White 24vDC GroundBrown 24vDC

Top view:

Pin-out

Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser when purchased from an authorized distributor, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.Mail in service can be obtained during the warranty period by calling (714) 424-6500. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale.

234 Fischer Avenue, Costa Mesa, California 92626 USA(714)424-6500 (800)840-0288 (714)424-6510 fax email: [email protected]

• Intelligent Entertainment • Infrastructure • Security Solutions

w w w . c h a n n e l v i s i o n . c o m500-370 Rev A

*iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.

500-370art - Channel Vision · PDF file100 Watt integrated class D amplifier ... ARIA’S...

Documents

Transcript of 500-370art - Channel Vision · PDF file100 Watt integrated class D amplifier ... ARIA’S...