5 MK series microswitches - Pizzato · 5 144 pc cap oc fs cd fr fap pc cap oc fs cd fr fap nc no...

5

139 General Catalogue Detection 2019-2020

Microswitches for safety applications

All microswitches showing the symbol besides the product code are with positive

opening and therefore suitable for safety applications. These microswitches are provi-

ded with a rigid connection between the plunger and the NC contacts, which are forcibly

actuated by a internal sturdy safety lever.

The positive opening has been designed in compliance with the standard EN 60947-5-1,

Annex K. Therefore, these microswitches are suitable for safety applications.

Contact reliability

In the following table a typical contact structure for a microswitch normally used in the industry (type A) is shown compared with the innovative

solution implemented by Pizzato Elettrica in the MK series microswitches: mobile contact with single interruption and double contacts (type B).

As you can see from the table below, in the latter contact structure (type B) the contact resistance (R) is only half in comparison to the mobile

contact with single interruption (type A), and presents a very low failure probability (fe) as well.

With a failure probability of x for a single switching operation, the failure probability for type A is fe=x, for type B fe x2. This means that if the

probability of a switching failure is x in a given situation, e.g., 1x10-4, (1 switching failure in 10,000), the result is as follows:

- for type A one failed commutation every 10,000. - for type B one failed commutation every 100,000,000.

Type Diagram DescriptionContact

resistance R

Probability of

errors fe

A

Common

microswitch

COMMON

NC

NO mobile contact

with single

interruption

R=Rc fe=x

B

Pizzato’s

microswitch

MK seriesNC

NOCOMMON

mobile contact

with single

interruption and

double contacts

R=Rc/2 fe x2

Safety lever

The microswitches of MK series have been designed to add new features to traditional and tested

microswitches by Pizzato Elettrica.

The absolute new feature of this series is the enhanced and state-of-the-art trigger mechanism, whose

design features are of higher quality in comparison to other solutions available on the market.

Thanks to the double and redundant execution, the electrical contact of the new microswitch has been

designed with a technology providing increased reliability, and is able to carry out switching operations with

positive opening. Inside the housing of the new microswitch it is possibile to insert gaskets to protect the

mechanism against fine dusts or liquids up to the protection degree IP65. Conductor fixing terminals are

more practical, allowing for cables of different diameters to be fixed or the choice of different bends for the

Faston contacts.

Description

Extended temperature range

The new MK series includes versions with extended temperature range available upon request. Compared

to the standard MK microswitches with temperature ranges from +85 C° to -25 C°, these special versions

are suitable for environments with temperature ranges from +85 C° to -40 °C. They can therefore be installed

inside cold stores, sterilizers or other equipment with very low ambient temperature. The special materials

used to produce these versions retain their characteristics even under these conditions, thereby expanding

the installation possibilities.

MK series microswitches

5

140General Catalogue Detection 2019-2020

Actuators with variable orientation

Thanks to the patented lateral fixing

system, the roller of the microswitches

MK•••15andMK••17canbenowrotatedin 90° steps.

The lateral fixing allows to disconnect the

actuator from the switch body even when

the actuator is already fixed to the support

bracket. The flexibility of the product also

allows for products to be unified in the

warehouse for applications that require

castors both in the longitudinal or tran-

sverse direction.

Protection degree IP65

By installing microswitches MK ••2••• with terminal coversVFMKC•22orterminalcoversVFMKC•23,amicroswitchfullyprotected against water and dust is obtained. Thanks to their

special oil resistant rubber gaskets the protection degree IP65

is provided. For applications in very dirty environments there

are also versions with integrated double gasket for the plunger

(internal+external).e.g.MK••2•12orMK••2•13. Gaskets

Microswitch:

MKV12D12

Terminal cover:

VF MKCV22

Clamping screw plates for cables of different diameters (MK V•)

Terminal covers with side-by-side strain relief cable gland

The clamping screw plates are provided with a particular “roofing tile” structure and are loosely cou-

pled to the clamping screw. The design causes connection wires of different diameter to be pulled

towards the screw when tightening the screw (see figure), preventing the wires from escaping

towards the outside.

The new terminal covers are provided

with strain relief cable gland and protec-

tion degree up to IP65. These are snap-

on terminal covers and have reduced

dimensions contained in the profile of

the microswitch so that these can be

installed on microswitches fixed side by

side as well.

5

141

D01 D02 D03 D04 D05 D06 D08

D30 D31 D32 D35 D37 D40 D42

R30 R31 R32 R35 R40 R42

F30 F31 F32 F35 F40 F42

General Catalogue Detection 2019-2020

PLUNGER

DIRECT

ACTUATION

LEVER

DIRECT

ACTUA-

TION

LEVER

INVERTED

ACTUA-

TION

LEVER

DIRECT

ACTUATION

AT THE BACK

ACTUATORS

TERMINALS

1 2 3

1NO+1NC, snap action1NO, snap action

(on request)

1NC, snap action

(on request)

V H F G

Screw with

self-lifting plate

Faston6.3mm,vertical Faston6.3mm 45° bend to the right

Faston6.3mm 45° bend to the left

(on request)

Product options

Sold separately as accessory


5

142

MK V12D40-GR16T6

D45 D46 D47 D53 D59 D49

R45 R46 R47 R53 R59 R60

F45 F46 F47 F53 F59 F49

D09 D10 D12 D13 D15 D17 D18 D19


Code structure Attention! The feasibility of a code number does not mean the effective availability of a product. Please contact our sales office.

Contact block

1 1NO+1NC, snap action, change-over

2 1NO, snap action (on request)

3 1NC, snap action (on request)

Type of actuation

D direct actuation

R inverted actuation

F direct actuation at the back

Maximum protection degree

1 IP40 (with terminal cover)

2 IP65 (with terminal cover)

Rollers

standard roller

R16metal roller Ø 9.5x4 mm

(foractuators40,42,45,46,47,53,59only)

R10large plastic roller Ø 9.8x8.4 mm

(foractuators40,42,45,53only)

Terminal type

V screw with self-lifting plate

H vertical faston

F Faston, 45° bend to the right

GFaston, 45° bend to the left(on request)

Actuator

01 pin

02 pin

03 narrow plunger

.. ................

Contact type

silver contacts (standard)

G silver contacts, 1 µm gold coating

Ambient temperature

-25°C … +85°C (standard)

T6 -40°C … +85°C

External

gasket

External

gasket

article options

5

143 General Catalogue Detection 2019-2020

In compliance with standards:

IEC 60947-5-1, EN 60947-5-1, IEC 60529, EN 60529, EN 60947-1, IEC 60947-1,

EN 50581.

Approvals:

UL 508, CSA 22.2 No.14, EN 60947-1, EN 60947-5-1.

Main features

•Technopolymer housing

•High reliability contacts

•Protection degree up to IP65

•4 terminal types available

•52 actuators available

•Versions with positive opening

•Versions with gold-plated silver contacts

•Terminal covers with strain relief cable gland

Housing

Housing made of glass fibre reinforced technopolymer, self-extinguishing and shock-proof.Protection degree acc. to EN 60529: IP00 without terminal cover

IP20 (withterminalcoversVFC01,VFC03)

IP40 (withterminalcoversVFMKC•1•,VFC02)

IP65 (withterminalcoversVFMKC•22+ MKV•2•••orVFMKC•23+MKH•2•••)

General dataAmbient temperature: -25°C … +85°C (standard)

-40°C … +85°C (T6 option)

Max. actuation frequency: 3600operatingcycles/hourMechanical endurance: 10 million operating cycles

Safety parameter B10D

: 20,000,000 for NC contacts

Tightening torques for installation: seepage233

Alternating current: AC15 (50 … 60 Hz)

Ue (V) 120 250

Ie(A) 3 5Directcurrent:DC13Ue (V) 24 125 250

Ie(A) 4 0.6 0.3

Thermal current (Ith): 16 A

Rated insulation voltage (Ui): 250Vac300Vdc

Rated impulse withstand voltage (Uimp

): 4 kV

Conditional short circuit current: 1000 A acc. to EN 60947-5-1

Protection against short circuits: type gG fuse 16 A 250 V

Pollution degree: 3Dielectric strength 2000 Vac/min.

Electrical data Utilization category

Installation for safety applications:

Use only microswitches marked with the symbol next to the product code. Always connect the safety circuit to the NC contacts (normally

closed contacts) as required by EN ISO 14119, paragraph 5.4 for specific interlock applications and EN ISO 13849-2 tables D3 (well-tried

components) and D.8 (failure exclusions) for safety applications in general. Actuate the switch at least up to the positive opening travel

(CAP) reported next to the article code. Actuate the switch at least with the positive opening force (FAP) reported next to the article code.

Quality marks:

IMQ approval: CA02.05772

ULapproval: E131787CCCapproval: 2013010305604291EAC approval: RU C-IT.УT03.В.00035/19

If not expressly indicated in this chapter, for correct installation and utilization of all articles see the instructions given on pages

223 to 236.


Compliance with the requirements of:

LowVoltageDirective2014/35/EU,EMCDirective2014/30/EU, RoHS Directive 2011/65/EU.

Positive contact opening in conformity with standards:

IEC 60947-5-1, EN 60947-5-1.

Conductor cross section (flexible copper strands)MK series: min. 1x0.34mm2 (1 x AWG 22)

max. 2 x 1.5 mm2 (2 x AWG 16)

Wire stripping length (x): xx

MK V••••• articles (screw connection): 7 mm

Technical data

5

144

PC

CA

P

OC

CDFS FR

FAP

PC

CA

P

OC

CDFS FR

FAP

NC

NOCOMMON

COMMON NC NO COMMON NO NCCOMMON NC NO

23.3

16.6

14.6

11.9 25.4 11.9

9.7

4.2

49.2

4.2x5

17.4

Ø 2.5

24.3

26.3

12.2

23.3

11.9 25.4 11.9

14.618

.4

9.7

49.2

4.24.2x5

12.2

17.4

28.1

24.3

Ø 2.5

11.925.411.9

23.3

14.624

.5

9.7

4.2

49.2

4.2x512.2

17.4

Ø 3.8

Ø 7

34.2

24.3

23.3

14.6

28.5

11.9 25.4 11.9

9.7

49.2

4.24.2x5

12.2

17.4

Ø 3.8

Ø 7

38.2

24.3

Electrical Ratings: Q300pilotduty (69 VA, 125-250 V dc)

A300pilotduty (720VA,120-300Vac)


MK V11D01 1NO+1NC PCOCCD

0.5 mm1.5 mm0.05 mm

FSFR

4 N3N


0.5 mm2 mm0.05 mm

FSFR

4 N3N


0.5 mm2 mm0.05 mm

FSFR

4 N3N


0.5 mm2 mm0.05 mm

FSFR

4 N3N

PC pre-travel

CAP positive opening travel

OC over-travel

CD differential travel

FS Trigger force

FR release force

FAP positive opening force

With direct actuation and direct actuation at the back (F, D) With inverted actuation (R)

Circuit diagram

Mobile contact with single interruption

and double contacts

Maximum and minimum speed see page233-type1 Maximum and minimum speed see page233-type1


Microswitches with direct actuation

Features approved by IMQ

Please contact our technical department for the list of approved products.

Rated insulation voltage (Ui): 250 Vac

Conventional free air thermal current (Ith): 16 A

Protection against short circuits: type gG fuse 16 A 250 V

Rated impulse withstand voltage (Uimp

): 4 kV

Conditional short circuit current: 1000 A

Protection degree of the housing: IP00

Terminals: screw terminals / faston

Pollution degree: 3Utilization category: AC15

Operating voltage (Ue): 250 Vac (50 Hz)

Operating current (Ie): 5 A

Forms of the contact element: X; Y; C

Positiveopeningofcontactsoncontactblocks:1,3

In compliance with standards: EN 60947-1, EN 60947-5-1, fundamental

requirementsoftheLowVoltageDirective2014/35/EU.

Please contact our technical department for the list of approved products.

Features approved by UL

All values in the drawings are in mm

Actuation forces and travels

Accessories See page 197Accessories See page 197 The2Dand3Dfilesareavailableatwww.pizzato.comAccessories See page 197Accessories See page 207

5

145

23.3

11.9 25.4 11.9

14.621

.5

9.7

49.2

4.2

4.2x5

17.4

Ø 6.8

12.2

31.2

24.3

25.411.9 11.9

23.3

28

16.4

8

9.7

4.2

49.2

4.2x5

Ø 6.8

M 10 x0.75

12.2

17.4

37.7

26.1

11.9 25.4 11.9

23.3

16

.4

50

.5

9.7

28

.1

2.5

4.2

49.2

4.2x512.2

17.4

60

.2

Ø 6.8

M10 x0.75

26

.1

14

21

.1 m

ax.

11.9 25.4 11.9

16.4

38

23.3

15.6

9.7

49.2

4.2

2.5

4.2x512.2

17.4

M10 x 0.75

14

8.6

max.

26.1

47.7

Ø6.8

11.9 25.4 11.9

16.4

41.5

23.3

9.7

25.1

49.2

4.2

2.52.

5

14

4.2x5

17.4

12.2

17

51.2

26.1

0.85

max

.

Ø 6.8

Ø 17.2

M 12 x1

14

3

12

15

49.2

33

.6

12.2

17.4

59

.7

17

M12 x17 m

ax.

26

.1

3.8

14

3

3.8

49.2

15

33.6

12

12.2

17.4

17

26.1

8 m

ax.

59.7

M12x1

11.9 25.4 11.9

23.3

16.4

38

9.7

2.5

15.6

49.2

4.24.2x5

26.1

47.7

12.2

17.4

14

8.6

max. Ø 6.8

M12 x1

11.9 25.4 11.9

16.4

9.3

41.5

23.3

9.7

49.2

2.5

4.24.2x5

12.2

17.426.1

14

M12 x1

51.2

4.8

max.

Ø 6.8

Ø 10.6

3.6

26.1

17.4

49.6

12.2

Ø 10.5

25.4

9.7

11.9 11.9

40

23.3

16.4

12

49.2

23.6

4.2x5

4.2


MK V11D08 1NO+1NC PCOCCDCAP

0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.5 mm2 mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.5 mm3mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.6 mm5.4 mm0.05 mm2.2 mm

FSFRFAP

6 N .4 N20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N.20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4.5 N3N.20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N20 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N.20 N




Maximum and minimum speed see page233-type2


Mounting only through threaded fitting

Mounting only through threaded fitting



Accessories See page 197Accessories See page 197 The2Dand3Dfilesareavailableatwww.pizzato.comAccessories See page 197Accessories See page 207All values in the drawings are in mm

5

146

17 23.3

11.9 11.925.4

R=26.2

49.2 17.4

32.9

29.5

12.2

0.9

5

11.9 25.4 11.9

13.717

0.9 27.4

9.7

49.2

4.2

R= 54

4.2x512.2

17.4

37.1

29.7

5

11.9 25.4 11.9

13.717

0.9 28.7

9.7

49.2

4.2

R= 63

4.2x512.2

17.4

38.4

29.7

5

11.9 25.4 11.9

13.717

0.9 39.7

~

9.7

49.2

4.2

R= 146.5

4.2x512.2

17.4

29.7

5

49.4

~

11.9 25.4 11.9

13.717

0.9

9.7

38.7

~

49.2

4.2

R= 139

4.2x512.2

17.4

29.7

Ø 1

48.4

~

11.925.411.9

17

34

.2

0.9

13

.79

.7

R= 24.6 9.5

4.2

49.2

4.2x5

17.4

12.2

4.2

43

.9

29

.7

11.9 25.4 11.9

9.7

35

.9

R=23.5

17

49.2

4.2

4.2x54.2

23

.7 45

.6

12.2

17.4

Ø 9.5

25.4

17 0.9

11.9 11.9

13

.7

R= 47.5

9.7

37

.4

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

47

.1

25.4

17 0.9

11.9 11.9

13

.7

R= 37.5

9.7

36

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

45

.7

12

23.6

26.1

49.7

17.4

12.2

Ø 10.5

11.9 25.4 11.9

9.7

16.4

40

23.3

49.2

23.6

3.6

4.2x54.2



9.1 mm7.1 mm0.9 mm

FSFR

0.76 N0.58 N


11.5 mm7.6 mm1.1 mm

FSFR

0.65 N0.5 N


26.2 mm13.7mm2.5 mm

FSFR

0.28 N0.22 N


0.5 mm5.5 mm0.05 mm2.2 mm

FSFRFAP

4 N3N.20 N


4.6 mm3.8mm0.4 mm

FSFR

1.66 N1.32N

MK V11D42 1NO+1NC PC

OC

CD

6.5 mm

4.8 mm

0.6 mm

FS

FR

1.09 N

0.84 N


OC

CD

4.5 mm

3.2mm0.4 mm

FS

FR

1.66 N

1.28 N


24.8 mm3.8mm4.1 mm

FSFR

0.08 N0.04 N


8.2 mm6.1 mm0.8 mm

FSFR

0.86 N0.66 N


OC

CD

4.1 mm

3.8mm0.4 mm

FS

FR

1.66 N

1.28 N











Accessories See page 197Accessories See page 197Accessories See page 197 The2Dand3Dfilesareavailableatwww.pizzato.comAccessories See page 207All values in the drawings are in mm

5

147

25.4

17

0.9

11.9 11.9

13

.7

45

.4

9.7

R= 24.6

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

55

.1

11.9 25.4 11.9

13.717

26.1

0.9

9.7

49.2

4.2

4.2x512.2

17.4

35.8

16.6

29.7

R= 38.2

25.4

17

0.9

13.7

11.9 11.9

9.7

38.4

R= 54

4.2

9.5

49.2

4.2x512.2

4.2

48.1

29.7

25.4

17

0.9

11.9 11.9

13

.7

R= 17.8

9.7

33

.2

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

42

.9

11.9 25.4 11.9

13.7 2

3.5

9.7

17

8.1

49.2

4.2

R= 63

4.2x512.2

17.4

33.2

29.7

5

12.2

17.423.8

5

31

R= 26.2

49.2

4.2

17

11.9 25.4 11.9

13.7

9.7

21.38.1

4.2x5

11.9 25.4 11.9

13.7

23

9.7

17 8.1

49.2

4.2

R= 54

12.2

17.4

32.7

29.7

5

4.2x5

11.9 25.4 11.9

8.1

49.2

4.2

R= 146.5

12.2

17.4

29.7

5

38.2

~

13.7

9.7

17

4.2x5

28.5

~

25.411.9 11.9

13.7

9.7

8.1

17

33.6

R= 47.5

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29.7

43.3

25.411.9 11.9

13

.79

.7

33

8.1

17

R= 37.5

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

42

.7



OC

CD

4.2 mm

2.8 mm

0.4 mm

FS

FR

1.66 N

1.28 NMK V11D49 1NO+1NC


OC

CD

7.7 mm

7.8 mm

0.9 mm

FS

FR

0.76 N

0.58 NMK V11D59 1NO+1NC PC

OC

CD

2.3mm4.5 mm

0.2 mm

FS

FR

2.3N1.77 N

MK V11R30 1NO+1NC PCOCCD

5 mm14 mm0.7 mm

FSFR

0.6 N0.4 N


1.9 mm5.1 mm0.23mm

FSFR

1.47 N0.72 N


13.4mm24.3mm2.1 mm

FSFR

0.3N0.2 N


2.8 mm10.9 mm0.45 mm

FSFR

0.8 N0.5 N


2.7 mm8.4 mm0.5 mm

FSFR

1.2 N1.7 N


4.1 mm11.2 mm0.8 mm

FSFR

0.7 N0.5 N



Microswitches with inverted actuation



Maximum and minimum speed see page233-type7Maximum and minimum speed see page233-type7

It switches It does not switch

Hand operated



Accessories See page 197Accessories See page 197Accessories See page 197Accessories See page 207 The2Dand3Dfilesareavailableatwww.pizzato.comAll values in the drawings are in mm

5

148

25.411.9 11.9

13.7

43.6

9.7

8.1

17

R= 24.6

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29.7

53.3

25.4

9.7

8.1

17

13.7

34

11.911.9

R= 54

4.2

9.5

49.2

4.2x512.2

17.4

43.7

4.2

29.7

25.411.9 11.9

13.7

9.7

31.8

17

8.1

R= 17.8

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29.7

41.5

25.411.9 11.9

13.7

28 -

48

9.7

8.1

17

R= 39

4.2

49.2

4.2x512.2

17.4

29.7

M 2.6

37.7

- 5

7.7

25.4

9.7

8.117

11.9 11.9

13.7

32.2

R= 24.6

4.2

49.2

4.2x5

12.2

41.9

29.7

4.2

17.4

11.9 25.4 11.9

9.7

R= 23.5

8.1

13.7

49.2

4.2

4.2

4.2x512.2

17.4

23.8 4

4.5

17

9.5

34.8

25.411.9 11.9

13.717

8.4 27.1

9.7

4.2

49.2

R= 69

4.2x512.2

17.4

5

29.7 36

.8

12.2

17.4

533.6

29.7

49.2

R= 32.2

4.2

25.411.9 11.9

17

13.7

9.7

23.98.4

4.2x5

25.4

17

8.4 26.1

13.7

11.911.9

9.7

4.2

49.2

R= 60

4.2x512.2

17.4

5

29.7 35

.8

11.9 25.4 11.9

13.7

9.7

35~

8.4

17

49.2

4.2

152.5

4.2x512.2

17.4

29.7

5

44.7

~



1.7 mm5.3mm0.3mm

FSFR

1.7 N1 N


3.6mm11.2 mm0.5 mm

FSFR

0.8 N0.4 N


1.5 mm3.9mm0.2 mm

FSFR

2.4 N1.3N


2.7 mm9.2 mm0.5 mm

FSFR

1.2 N0.6 N

MK V11F30 1NO+1NC PCOCCD

3.2mm11.2 mm0.35mm

FSFR

0.6 N 0.5 N

MK V11F31 1NO+1NC PCOCCDCAP

1.45 mm5 mm0.17 mm5.72 mm

FSFRFAP

1.5 N0.92 N5.78 N


7.8 mm24.1 mm1.7 mm

FSFR

0.25 N0.2 N


2.7 mm9.3mm0.4 mm

FSFR

0.7 N0.6 N


1.5 mm5.5 mm0.3mm

FSFR

1.7 N1 N


1.7 mm4.8 mm0.3mm

FSFR

1.8 N1.1 N






Microswitches with direct actuation at the back



Accessories See page 207 The2Dand3Dfilesareavailableatwww.pizzato.comAll values in the drawings are in mm

5

149

25.411.9 11.9

13.717

R= 53.5

8.4

9.7

36.4

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29.7

46.1

25.411.9 11.9

13

.717

8.4

35

.3

R= 43.5

9.7

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

45

25.411.9 11.9

13

.7

45

.3

9.7

17

8.4

R= 30.6

4.2

49.2

9.5

4.2x512.2

4.2

17.4

29

.7

55

25.4

9.7

11.911.9

17

13.7

268.4

4.2

49.2

4.2x512.2

17.4

16.6

35.7

29.7

R= 44.1

25.4

13.7

11.9 11.9

9.7

37.1

R= 60

8.4

17

4.2

9.5

49.2

4.2x512.2

4.2

46.8

29.7

25.4

13.7

11.9 11.9

9.7

33.2

8.4

17

R= 23.8

4.2

9.5

49.2

4.2x512.2

4.2

42.9

29.7

25.4

9.7

13.7

11.911.9

33.9

17

8.4

R= 30.6

4.2

9.5

49.2

4.2x512.2

17.4

4.2

43.6

R= 29.5 4.2

49.2

4.2

17

9.7

13

.7

36

.5

8.4

11.9 25.4 11.9

4.2x5

12.2

17.4

46

.2

29

.7

9.5

9.7

8.5

6.3 12.7 12.7 6.3

12.2

1919

7 710.8

14.3

6.3 12.7 12.7 6.3

19 19

6.3

12

12.7 12.7 6.36.3

45°

19 19 6.4

6.3

12

6.3 12.7 12.7 6.3

45°

19 196.4

6.3



1.8 mm6.7 mm0.2 mm8 mm

FSFRFAP

1 N0.7 N4.9 N


1.3mm4.7 mm0.1 mm5.8 mm

FSFRFAP

1.6 N0.9 N6.9 N


2.5 mm9.3mm0.3mm

FSFR

0.7 N0.6 N


0.8 mm4.5 mm0.08 mm4.9 mm

FSFRFAP

1.9 N1.3N8.9 N


1.5 mm7.5 mm0.2 mm8 mm

FSFRFAP

1 N0.7 N4.8 N


1.1 mm4.9 mm0.1 mm5.8 mm

FSFRFAP

1.5 N0.9 N6.9 N


1.3mm4.7 mm0.1 mm5.8 mm

FSFRFAP

1.6 N0.9 N6.9 N


2.1 mm8.3mm0.25 mm

FSFR

0.85 N0.65 N









Screw terminals V with plate Faston terminals H, vertical Faston terminals F, right angle Faston terminals G, left angle (upon request)

Note: The vertical faston terminals H can be bent according to specific installation requirements.

We recommend to bend the faston with an angle not higher than 45° and to carry out this operation no more than 5 times.

Terminal dimensions All values in the drawings are in mm

5

150

52.4

18

.5 25

.1

65.4

13

9

16

8.2

17.4

65.4

13

32 38.6

52.4

9

16

17.4

8.2

4.9 4.3 21.1 4.3

52.8

22.7 7.5 22.7

21

25.4

20.8

7.5

8.5

16

.6

53.8

4.4 4.4

10.5

4.3

22

2

0

68.3

25.4

25

16

10

10 8 15.3 8 10

9

12.2

18.7

17.2

51.3

8

14

M10x 0.75 2.5

14

M12 x1

2.5

M12x1

17

3


Accessories Packs of 10 pcs.

Article Description

VF AC83

Hex threaded nut for micro-

switches with actuators D06,

D08, D09

Article Description

VF AC72

Hex threaded nut for micro-

switches with actuators D10,

D12,D13

Article DescriptionProtection

degree

VF C01Protective terminal cover for screw termi-

nalsIP20


degree

VF C02

Protective terminal cover for screw termi-

nals with PG9 cable gland for multipolar

cables Ø 5 … 7 mm

IP40


degree

VF C03

Protective terminal cover for screw termi-

nals, snap-in mounting. It allows to install

mutiple switches side-by-side

IP20

Protective terminal cover for screw terminals with strain relief cable

gland and snap-in mounting. It allows to install mutiple switches side-

by-side.


degree

VF MKCV11Protective terminal cover without gasket for

multipolar cables Ø 5 … 7.5 mm IP40





VF MKCV22Protective terminal cover with gasket for

multipolar cables Ø 4 … 7.5 mmIP65

VF MKCV23Protective terminal cover with gasket for


Protective terminal covers Packs of 10 pcs.

Protective terminal cover for vertical faston terminals with strain

relief cable gland and snap-in mounting. It allows to install mutiple

switches side-by-side.


degree

VF MKCH11Protective terminal cover without gasket for






VF MKCH22Protective terminal cover with gasket for


VF MKCH23Protective terminal cover with gasket for


Accessories See page 197Accessories See page 197 The2Dand3Dfilesareavailableatwww.pizzato.comAccessories See page 197Accessories See page 207

Article Description

AC 35

Hex threaded nut, notched, for

microswitches with actuators

D15, D17

All values in the drawings are in mm

5 MK series microswitches - Pizzato · 5 144 pc cap oc fs cd fr fap pc cap oc fs cd fr fap nc no...

Documents

Transcript of 5 MK series microswitches - Pizzato · 5 144 pc cap oc fs cd fr fap pc cap oc fs cd fr fap nc no...