5. ART KG-2
1
ARTICLE KG-2 ORGANIZATION OF THIS DIVISION KG-200 ORGANIZATION KG-210 PARTS OF THIS DIVISION This Division is divided into eight parts. (a) Part KG contains the scope of the Division, estab- lishes the extent of its coverage, and sets forth the respon- sibilities of the User and Manufacturer and the duties of the Inspectors of vessels constructed under these rules. (b) Part KM contains (1) the materials which may be utilized (2) the permissible material specification identifi- cation numbers, special requirements, and limitations (3) mechanical and physical properties upon which the design is based, and other necessary information con- cerning material properties (see Section II, Part D) (c) Part KD contains requirements for the design of vessels and vessel parts. (d) Part KF contains requirements for the fabrication of vessels and vessel parts. (e) Part KR contains rules for pressure relief devices. (f) Part KE contains requirements for nondestructive examination and repair of materials, vessels, and vessel parts. (g) Part KT contains testing requirements and proce- dures. (h) Part KS contains requirements for stamping and certifying vessels and vessel parts. It also gives require- ments for Manufacturer’s Data Reports and Records to be furnished to the User. KG-220 APPENDICES KG-221 Mandatory The Mandatory Appendices address specific subjects not covered elsewhere in this Division. Their require- ments are mandatory when applicable. KG-222 Nonmandatory The Nonmandatory Appendices provide information and suggested good practices. 5 KG-230 ARTICLES AND PARAGRAPHS KG-231 Articles The main divisions of the Parts of this Division are designated Articles. These are given numbers and titles such as Article KG-1, Scope and Jurisdiction. KG-232 Paragraphs and Subparagraphs The Articles are divided into paragraphs and subpara- graphs which are given three-digit numbers, the first of which corresponds to the Article number. Each such para- graph or subparagraph number is prefixed with letters which, with the first digit (hundreds), indicate the Part and Article of this Division in which it is found, such as KD-140, which is a subparagraph of KD-100 in Article KD-1 of Part KD. (a) Major subdivisions of paragraphs or subparagraphs are indicated by the basic paragraph number followed by a decimal point and one or two digits. Each of these subdivisions are titled and appear in the table of contents. (b) Minor subdivisions of paragraphs are designated (a), (b), etc. (c) Where further subdivisions are needed, they are designated by numbers in parentheses [e.g. KG-311.8(b)(1)]. KG-240 REFERENCES When a Part, Article, or paragraph is referenced in this Division, the reference shall be taken to include all subdivisions under that Part, Article, or paragraph, includ- ing subparagraphs. KG-250 TERMS AND DEFINITIONS Terms and symbols used in this Division are defined in the various Parts, Articles, or paragraphs where they first apply or are of primary interest. A list of symbols is given in Mandatory Appendix 1. Copyright ASME International Provided by IHS under license with ASME Not for Resale No reproduction or networking permitted without license from IHS --`,,```,,,,````-`-`,,`,,`,`,,`---
-
Upload
aldeline-sungahid -
Category
Documents
-
view
213 -
download
0
description
efef
Transcript of 5. ART KG-2
ARTICLE KG-2ORGANIZATION OF THIS DIVISION
KG-200 ORGANIZATION
KG-210 PARTS OF THIS DIVISION
This Division is divided into eight parts.(a) Part KG contains the scope of the Division, estab-
lishes the extent of its coverage, and sets forth the respon-sibilities of the User and Manufacturer and the duties ofthe Inspectors of vessels constructed under these rules.
(b) Part KM contains(1) the materials which may be utilized(2) the permissible material specification identifi-
cation numbers, special requirements, and limitations(3) mechanical and physical properties upon which
the design is based, and other necessary information con-cerning material properties (see Section II, Part D)
(c) Part KD contains requirements for the design ofvessels and vessel parts.
(d) Part KF contains requirements for the fabricationof vessels and vessel parts.
(e) Part KR contains rules for pressure relief devices.(f) Part KE contains requirements for nondestructive
examination and repair of materials, vessels, and vesselparts.
(g) Part KT contains testing requirements and proce-dures.
(h) Part KS contains requirements for stamping andcertifying vessels and vessel parts. It also gives require-ments for Manufacturer’s Data Reports and Records tobe furnished to the User.
KG-220 APPENDICES
KG-221 Mandatory
The Mandatory Appendices address specific subjectsnot covered elsewhere in this Division. Their require-ments are mandatory when applicable.
KG-222 Nonmandatory
The Nonmandatory Appendices provide informationand suggested good practices.
5
KG-230 ARTICLES AND PARAGRAPHS
KG-231 Articles
The main divisions of the Parts of this Division aredesignated Articles. These are given numbers and titlessuch as Article KG-1, Scope and Jurisdiction.
KG-232 Paragraphs and Subparagraphs
The Articles are divided into paragraphs and subpara-graphs which are given three-digit numbers, the first ofwhich corresponds to the Article number. Each such para-graph or subparagraph number is prefixed with letterswhich, with the first digit (hundreds), indicate the Partand Article of this Division in which it is found, such asKD-140, which is a subparagraph of KD-100 in ArticleKD-1 of Part KD.
(a) Major subdivisions of paragraphs or subparagraphsare indicated by the basic paragraph number followed bya decimal point and one or two digits. Each of thesesubdivisions are titled and appear in the table of contents.
(b) Minor subdivisions of paragraphs are designated(a), (b), etc.
(c) Where further subdivisions are needed, they aredesignated by numbers in parentheses [e.g.KG-311.8(b)(1)].
KG-240 REFERENCES
When a Part, Article, or paragraph is referenced inthis Division, the reference shall be taken to include allsubdivisions under that Part, Article, or paragraph, includ-ing subparagraphs.
KG-250 TERMS AND DEFINITIONS
Terms and symbols used in this Division are definedin the various Parts, Articles, or paragraphs where theyfirst apply or are of primary interest. A list of symbolsis given in Mandatory Appendix 1.
Copyright ASME International Provided by IHS under license with ASME
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
