4'x8' FLOOD TRAY STAND HGSFT48 – Active Aqua 4 Flood ......CLAVE PARA EL DIAGRAMA DE MONTAJE...

4
A 3 I 1 B SPECIFICATIONS Dimensions 4' x 8' Weight 75 lbs Light bar capacity Up to 2 light systems (depending on size/weight of fixtures) PARTS STAND A Legs with moveable casters x 4ea B Side bar reinforcements (flat plate) x 2ea C End bar reinforcements x 2ea D Tray support bar x 2ea E Light hanger cross bar x 1ea F. Light hanger vercal support, upper x 2ea G. Light hanger vercal support, lower (thin, short bar) x 2ea H Light hanger bar corner truss x 2ea I Side bar reinforcements (curved bar) x2ea J Light hanger bar cross bar center support x1ea ASSEMBLY INSTRUCTIONS IMPORTANT: See page 8 for a comprehensive assembly overview. TRAY STAND 1. Gather the appropriate tools needed for assembly Remove all of the parts from the packaging and set the hardware aside 2. Group all of the stand parts together based on type for ease of locang and assembly – i.e., legs together, side bars together, end bars together, and so on. 3. FIGURE 1 – Aach (1) of each of the side bar reinforcements (B & I) together lengthwise, with (1) leg A between them secured with (2) #1 bolts and (2) nuts. Curved plate side reinforcement (I) goes on the outside of the flat plate. NOTES: The side bar reinforcements have pre-drilled holes located on the boom support bar for aaching the tray support bars. Ensure these holes are on the boom bar (facing the caster wheel), and not on the top when aaching the two reinforcements to the legs. For ease of assembly, do not completely ghten nuts and bolts unl all pieces are assembled. HARDWARE 1 Hex head bolt 13mm (⅜″ x 1.8″, 45mm) x28 ea 2 Hex head bolt 13mm (⅜″ x 2.2″, 55mm) x4 ea 3 Nuts (14mm) x28 ea 4 Cap nut (16mm) x4 ea 5 35" (90mm) tray support pin x4 ea 6. Plasc washer for pin x4 ea 7 Pin spacer (for Botanicare 4'x 8' tray) x4 ea REQUIRED TOOLS: Adjustable wrench (13, 14 & 17mm) A ladder and two people 4'x8' FLOOD TRAY STAND ASSEMBLY INSTRUCTIONS FIGURE 1 Stand is easier to assemble upside down. Make sure pre-drilled holes are on boom bar (same side as casters). © Hydrofarm, Inc. v.3 10/2011 page 8 © Hydrofarm, Inc. v.3 10/2011 ASSEMBLY OVERVIEW VISION GENERAL DEL MONTAJE VUE D’ENSEMBLE DU MONTAGE HGSFT48 – Acve Aqua 4' x 8' Flood Tray Stand HGSFT48 – Acve Aqua 4' x 8' Flood Tray Stand See Assembly Overview diagram on page 4 for an alternate view of the flat (B) and curved (I) side bar reinforcements. KEY TO ASSEMBLY DIAGRAMS STAND A Legs with moveable casters B Side bar reinforcements (flat plate) C End bar reinforcements D Tray support bar E Light hanger cross bar F. Light hanger vercal support, upper G. Light hanger vercal support, lower (thin bar) H Light hanger bar corner truss I Side bar reinforcements (curved bar) J Light hanger bar cross bar center support HARDWARE 1 Hex head bolt (13mm x 45mm L) 2 Hex head bolt (13mm x 55mm L) 3 Nuts (14mm) 4 Cap nut (16mm) 5 35(90mm) tray support pin 6. Plasc washer for pin 7 Pin spacer (for Botanicare tray) 2 2 1 1 1 6 5 7 I I F I 1 3 3 3 3 A A H D B C 4 FIGURE 6, alternate view 4 G G C FIGURE 7, alternate view B B J E 1 1 1 3 3 F G FIGURE 1, alternate view FIGURE 5, alternate view CLAVE PARA EL DIAGRAMA DE MONTAJE SOPORTE A Patas con ruedas móviles B Refuerzos de barra lateral (barra plana) C Refuerzos de barras extremas D Barra de soporte de la bandeja E Barra de suspensión de la luz F. Soporte vercal de suspensión de la luz, superior G. Soporte vercal de suspensión de la luz, inferior (barra corta, fina) H Viga de esquina de la barra de suspensión de la luz I Refuerzos de barra lateral (barra curva) J Soporte central de la barra transversal de suspensión de luz ACESSORIOS 1 Tornillo de cabeza hexagonal (13mm x 45mm) 2 Tornillo de cabeza hexagonal (13mm x 55mm) 3 Tuercas (14 mm) 4 Tuerca ciega (16 mm) 5 Perno de soporte de la bandeja (90mm) 6. Arandela de plásco para el perno 7 Perno espaciador (HGSFT44 solamente) LEGENDE DES DIAGRAMMES DE MONTAGE SUPPORT A. Pieds à roulees amovibles B Barres latérales de renfort (plaque plate) C Barres de renfort d’extrémité D Barre de support du bac E Barre de suspension transversale F. Support supérieur vercal G. Support inférieur vercal (pete barre étroite) H Armature d’angle I Barres latérales de renfort (barre courbe) J Barre de suspension transversale centrale MATERIAUX 1 Boulon à tête héxagonale (13mm x 45mm) 2 Boulon à tête héxagonale (13mm x 55mm) 3 Ecrou (14mm) 4. Caloe écrou (16mm) 5 Broches support du bac 35" (90mm) 6. Joint plasque pour broche 7 Espaceur de broche (Seulement pour HGSFT44) Check hydrofarm.com for the most up-to-date list of compable trays.

Transcript of 4'x8' FLOOD TRAY STAND HGSFT48 – Active Aqua 4 Flood ......CLAVE PARA EL DIAGRAMA DE MONTAJE...

  • A

    3I

    1

    B

    SPECIFICATIONS Dimensions . . . . . . . . . .4' x 8' Weight . . . . . . . . . . . . . .75 lbs Light bar capacity . . . . . Up to 2 light systems

    (depending on size/weight of fixtures)

    PARTS STAND A . Legs with moveable casters . . . . . . . . x 4ea . B . Side bar reinforcements (flat plate) . . x 2ea . C . End bar reinforcements . . . . . . . . . . . . x 2ea . D . Tray support bar . . . . . . . . . . . . . . . . . . x 2ea . E . Light hanger cross bar . . . . . . . . . . . . . x 1ea . F. Lighthangerverticalsupport,upper . . . . x 2ea . G.Lighthangerverticalsupport,lower (thin, short bar) . . . . . . . . . . . . . . . . . . . . . . . x 2ea . H . Light hanger bar corner truss . . . . . . . x 2ea . I . Side bar reinforcements (curved bar) . x2ea . J . Light hanger bar cross bar center support . . . . . . . . . . . . . . . . . . . x1ea .

    ASSEMBLY INSTRUCTIONSIMPORTANT: See page 8 for a comprehensive assembly overview.

    TRAY STAND

    1. Gather the appropriate tools needed for assembly . Remove all of the parts from the packaging and set the hardware aside .

    2. Group all of the stand parts together based on type for easeoflocatingandassembly–i.e.,legstogether,sidebarstogether,endbarstogether,andsoon.

    3. FIGURE 1 –Attach(1)ofeachofthesidebarreinforcements(B&I)togetherlengthwise,with(1)legAbetweenthemsecuredwith(2)#1boltsand(2)nuts.Curvedplatesidereinforcement(I)goesontheoutsideoftheflatplate.

    NOTES:•The side bar reinforcements have pre-drilled holes located

    on the bottom support bar for attaching the tray support bars. Ensure these holes are on the bottom bar (facing the caster wheel), and not on the top when attaching the two reinforcements to the legs.

    •For ease of assembly, do not completely tighten nuts and bolts until all pieces are assembled.

    HARDWARE 1 . Hex head bolt 13mm (⅜″ x 1.8″, 45mm) . . . x28 ea . 2 . Hex head bolt 13mm (⅜″ x 2.2″, 55mm) . . . . x4 ea . 3 . Nuts (14mm) . . . . . . . . . . . . . . . . . . . . . . . . . x28 ea . 4 . Cap nut (16mm) . . . . . . . . . . . . . . . . . . . . . . . . x4 ea . 5 . 3 .5" (90mm) tray support pin . . . . . . . . . . . . . x4 ea . 6. Plasticwasherforpin . . . . . . . . . . . . . . . . . . . x4 ea . 7 . Pin spacer (for Botanicare 4'x 8' tray) . . . . . . x4 ea .

    REQUIRED TOOLS: Adjustable wrench (13, 14 & 17mm) A ladder and two people

    4'x8' FLOOD TRAY STANDASSEMBLY INSTRUCTIONS

    FIGURE 1

    Stand is easier to assemble upside down.

    Make sure pre-drilled holes are on bottom bar (same side as casters).

    © Hydrofarm, Inc. v.3 10/2011page 8 © Hydrofarm, Inc. v.3 10/2011

    ASSEMBLY OVERVIEWVISION GENERAL DEL MONTAJEVUE D’ENSEMBLE DU MONTAGE

    HGSFT48 – Active Aqua 4' x 8' Flood Tray Stand

    HGSFT48 – Active Aqua 4' x 8' Flood Tray Stand

    See Assembly Overview diagram on page 4 for an alternate view of the flat (B) and curved (I) side bar reinforcements.

    KEY TO ASSEMBLY DIAGRAMSSTANDA . Legs with moveable castersB . Side bar reinforcements (flat plate)C . End bar reinforcementsD . Tray support barE . Light hanger cross barF. Lighthangerverticalsupport,upperG. Lighthangerverticalsupport,lower(thin bar)H . Light hanger bar corner truss I . Side bar reinforcements (curved bar) J . Light hanger bar cross bar center support

    HARDWARE1 . Hex head bolt (13mm x 45mm L)2 . Hex head bolt (13mm x 55mm L)3 . Nuts (14mm)4 . Cap nut (16mm)5 . 3 .5” (90mm) tray support pin6. Plasticwasherforpin7 . Pin spacer (for Botanicare tray)

    2

    2

    1

    1

    1

    65

    7

    I

    I

    F

    I

    1

    3

    3

    3

    3

    A

    A

    H

    D

    BC

    4

    FIGURE 6, alternate view

    4

    G

    G

    C

    FIGURE 7, alternate view

    B

    B

    J

    E

    11

    1

    3

    3

    F

    G

    FIGURE 1, alternate view

    FIGURE 5, alternate view

    CLAVE PARA EL DIAGRAMA DE MONTAJE SOPORTEA . Patas con ruedas móvilesB . Refuerzos de barra lateral (barra plana)C . Refuerzos de barras extremasD . Barra de soporte de la bandejaE . Barra de suspensión de la luzF.Soporteverticaldesuspensióndelaluz,superiorG.Soporteverticaldesuspensióndelaluz,inferior

    (barra corta, fina)H . Viga de esquina de la barra de suspensión de la luzI . Refuerzos de barra lateral (barra curva)J . Soporte central de la barra transversal de suspensión

    de luz

    ACESSORIOS1 . Tornillo de cabeza hexagonal (13mm x 45mm)2 . Tornillo de cabeza hexagonal (13mm x 55mm) 3 . Tuercas (14 mm) 4 . Tuerca ciega (16 mm)5 . Perno de soporte de la bandeja (90mm) 6.Arandeladeplásticoparaelperno7 . Perno espaciador (HGSFT44 solamente)

    LEGENDE DES DIAGRAMMES DE MONTAGE SUPPORTA.PiedsàroulettesamoviblesB . Barres latérales de renfort (plaque plate)C . Barres de renfort d’extrémitéD . Barre de support du bacE . Barre de suspension transversaleF.SupportsupérieurverticalG.Supportinférieurvertical(petite barre étroite) H . Armature d’angleI . Barres latérales de renfort (barre courbe)J . Barre de suspension transversale centrale

    MATERIAUX1 . Boulon à tête héxagonale (13mm x 45mm)2 . Boulon à tête héxagonale (13mm x 55mm)3 . Ecrou (14mm)4.Calotteécrou(16mm)5 . Broches support du bac 3 .5" (90mm)6.Jointplastiquepourbroche7 . Espaceur de broche (Seulement pour HGSFT44) Check hydrofarm.com for the most

    up-to-date list of compatible trays.

  • ASSEMBLY INSTRUCTIONS, continued

    page 2 © Hydrofarm, Inc. v.3 10/2011

    4. FIGURE 2 –Attach(1)legtoeachendofthesidebarassemblyusing(2)#1boltsand(2)nuts.Thereshouldbeatotalof(3)legsoneachside bar reinforcement assembly .

    5.RepeatSteps3and4withtheremaining(2)sidebarreinforcementsand(3)legs.

    6. FIGURE 3 – Join(1)endbarreinforcement(C)tooneofthesidebarassemblylegsusing(2)#1boltsand(2)nuts.Thecompletedassembly should resemble an “L” shape .

    7. Repeat Step 6 using the remaining end bar reinforcement .

    NOTE: At this point you should have successfully assembled (2) main structures that make up the body of the tray stand.

    8. FIGURE 4 – Attachthetwostructurestogetherusing(4)#1boltsand(4)nuts.Thestandshouldbecompleteasidefromthelighthangerbar and support bars .

    9. Flip the stand right side up so that it is standing on the moveable casters .

    10. FIGURE 5 – Attachthe(4)traysupports(D)perpendiculartothelength of the tray stand . The pre-drilled holes are on the top of the lowerbarsofthesidebarreinforcementsasmentionedinStep3.Use(8)#5pins.IfusingaBotanicaretray(white),usetheincluded#7spacersand#6plasticwasherstoraisethetraysupports(D)offofthelowerbarsofthesidebarreinforcements(B&I).

    A

    31

    FIGURE 2

    NOTE: The tray supports should be installed on TOP of the bottom support bars of the side bar reinforcements. These provide structural support for the flood trays so that there is no fluctuation in tray balance.

    HGSFT48 – Active Aqua 4' x 8' Flood Tray Stand

    STANDA . Legs with moveable castersB.Sidebarreinforcements(flatplate)C . End bar reinforcementsD . Tray support barE . Light hanger cross barF.Lighthangerverticalsupport,upperG.Lighthangerverticalsupport,lowerH . Light hanger bar corner truss I.Sidebarreinforcements(curvedbar) J . Light hanger bar cross bar center

    support

    HARDWARE 1 . Hex head bolt (13mm x 45mm)2 . Hex head bolt (13mm x 55mm)3 . Nuts (14mm)4 . Cap nut (16mm)5 . 3 .5” (90mm) tray support pin6.Plasticwasherforpin7 . Pin spacer (for Botanicare tray)

    KEY TO ASSEMBLY DIAGRAMS

    13

    FIGURE 3

    C

    FIGURE 4

    1

    3

    D

    56

    FIGURE 5See page 8 for alternate view.

    INSTRUCTIONS de MONTAGE, continué

    13

    F

    H

    FIGURE 81

    3

    FIGURE 9

    © Hydrofarm, Inc. v.3 10/2011 page 7

    13

    F

    FIGURE 10

    Consulter la page 8 pour une perspective differente.

    J

    E

    E

    1

    J

    3

    FIGURE 7

    D

    56

    Consulter la page 8 pour une perspective differente.

    FIGURE 5

    42

    G

    Consulter la page 8 pour une perspective differente.

    FIGURE 6

    NOTE: Les supports de bac doivent être posés dessus des barres de support inferieures des barres laterales de renfort. Celles ci apportent un soutien structural aux flood trays de façon à ce qu’il n’y ait pas de fluctuation dans l’équilibrage du bac.

    Instructions pour 4' x 8' Active Aqua Flood Tray – HGSFT48

    10. FIGURE 5 –Joindreles(4)supportsdebac(D)perpendiculairement à la longueur de stand de bac . Les trous pré-foréssontsurlapartiesupèrieuredesbarresinférieuresdes barres latérales de renfort comme il est décrit dans l'étape 3.Utiliser(8)broches)#5.SilebacBotanicare(blanc)estutilisé,servezvousdesespaceurs#7inclusainsiquelesjointsenplastique#6poursuréleverlessupportsdebac(D)parrapport aux barres inférieures des barres latérales de renfort (B&I).

    BARRE POUR ACCROCHER UNE LAMPE1. FIGURE 6 – Attacherlessupportsverticauxdelabarre

    inférieured’accrochage(G)austanddebacenutilisantlestrouspré-forésaucentredesbarresderenfort(C).Utiliser(1)boulon#2et(1)calotted’écroupartroupré-foré.

    2. FIGURE 7 – Joindreles(2)barrestransversales(E)ensembleenutilisantlesupportcentraldelabarre(J),(2)boulons#1et(2)écrous.Cetteassembléecomplétéedevraitêtreapproximativement8'long.

    3. FIGURE 8 – Placerlabarretransversaledesuspension(F)surlessupportsdel’armature(H)etalignerlestrouspré-foréssitués aux extremités de la barre avec ceux de l’armature . Mettrelemêmeboulon#1queceluiutilisédanslesétapesprécédentessurledessusdelabarrepourl’attacherauxarmatures d’angle .

    4. FIGURE 9 – Placer la barre transversale de suspension sur les supports de l'armature et aligner les trous pré-forés situés aux extremitésdelabarreavecceuxdel'armature.(4)boulons#1et(4)écrousinsérésdepuislehautdelabarrejusqu'àl'armaturemaintiendrontletoutsolidement.

    5. FIGURE 10 – Faire glisser l'assemblage de la barre de suspension supérieure/barre transversale dans les barres de supportinférieuresetalignerlestrous.Visseravecboulon#1comme pour les étapes précédentes .

    Le stand de table d’inondations Active Aqua devrait être terminée et prête à soutenir une table d’inondations Active Aqua ou un bac Botanicare 4' x 8', ainsi que le kit espaceur inclus et jusqu'à (3) systèmes lumineux (2 si le Raptor est utilisé).

  • SPECIFICATIONSDimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4’ x 8’Poids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 lbsCapacité de la rampe lumineuse . . . . . . Peut accommoder 2 lampes (selon taille/poids)

    OUTILS NECESSAIRESClé ajustable (13, 14 & 16mm) Echelle et 2 personnes

    INSTRUCTIONS DE MONTAGEIMPORTANT: Voir page 8 pour meilleure vue d’ensemble du montage

    STAND DE BAC1. Rassemblerlesoutilsnécessairespourlemontage.Sortirtoutes

    lespiècesdupaquetetmettrelematérieldecôté.2. Groupertouteslespiècesdustandpoursimplifierlemontage--

    les pieds ensemble; les barres latérales ou du bout ensemble etc3. FIGURE 1 – Joindreunedechaquebarrelatéralederenfort(B

    &I)ensemblesurlalongueuràl'aided'unpiedAentreelles,sécuriséenutilisant(2)boulons#1et(2)écrous.Laplaquederenfortcourbe(1)sepaceàl'exterieurdelaplaqueplate.

    4. FIGURE 2 –Joindre(1)piedàchaqueextrémitédelabarredemontagelatéraleenutilisant(2)boulons#1et(2)écrous.Ildevraityavoiruntotalde(3)piedssurchaquebarrelatéralederenfort .

    5. Répéterétapes3et4avecles(2)barreslatéralesderenfortetles(3)piedsrestants.

    6. FIGURE 3 –Joindre(1)barrederenfortd'extrémité(C)àundespiedsdel'assemblagedebarreslatéralesenutilisant(2)boulons#1et(2)écrous.L'assemblageterminédevraitavoirlaformed'un "L" .

    7. Répéter l'étape 6 en joignant la barre de renfort restante .

    NOTE: Vous devriez à présent avoir monté les (2) structures principales qui forment le corps du support de bac.

    8. FIGURE 4 – Joindre les deux structures ensemble à l'aide des (4)boulons)#1etdes(4)écrous.Lestanddevraitêtreterminéà part de la barre de suspension de lampe et des barres de support .

    9. Retournerlestandàl'endroitetposerlesursesroulettes.

    FIGURE 1

    1

    A

    3B

    Le stand est plus facile à monter à l’envers.

    Vous assurer que les trous pré-forés sont bien dans le bas de la barre (du même coté que les roulettes).

    page 6

    PIECES SUPPORTA . Piedsàroulettesamovibles . . . . . . . . . . . . .4xB . Barres latérales de renfort (plaque plate) .2xC . Barres de renfort d’extrémité . . . . . . . . . . .2xD . Barre de support du bac . . . . . . . . . . . . . . .2xE . Barre de suspension transversale . . . . . . . .1xF.Supportsupérieurvertical . . . . . . . . . . . . . .2x

    G.Supportinférieurvertical (petite barre étroite) . . . . . . . . . . . . . . . . . .2x

    H . Armature d’angle . . . . . . . . . . . . . . . . . . . . .2xI . Barres latérales de renfort (barre courbe) . .2xJ . Barre de suspension transversale centrale .1x

    MATERIAUX1 . Boulon à tête hexagonale de 13mm (⅜” x 1.8”, 45mm) . . . . . . . . . . . . . . . . . . . .28x

    2 . Boulon à tête hexagonale de 13mm (⅜” x 2.2”, 55mm) . . . . . . . . . . . . . . . . . . . .4x3 . Ecrou (14mm) . . . . . . . . . . . . . . . . . . . . . . . .28x4.Calotteécrou(16mm) . . . . . . . . . . . . . . . . .4x5 . Broches support du bac 3 .5” (90mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . .4x6.Jointplastiquepourbroche . . . . . . . . . . . . .4x7 . Espaceur de broche (pour bac Botanicare 4’ x 8’) * . . . . . . . . . . . . . . . . . .4x *Seulement pour HGSFT44

    INSTRUCTIONS DE MONTAGEFR

    IConsulter le diagramme général sur page 8 pour voir la difference entre les barres de renforcement plates (B) et les barres courbes (I).

    A

    31

    FIGURE 2 FIGURE 3

    1 3C

    FIGURE 4

    1

    3

    Instructions pour 4' x 8' Active Aqua Flood Tray – HGSFT48LIGHT HANGER BAR

    1. FIGURE 6 – Attachthe(2)lighthangerverticalsupportlower(G),to the tray stand using the pre-drilled holes located in the center oftheendbarreinforcements(C).Use(1)#2boltand(1)capnutper pre-drilled hole .

    2. FIGURE 7 – Assemblethe(2)lighthangercrossbars(E)togetherusingthelighthangercentersupport(J),(2)#1boltsand(2)nuts.This completed assembly should be approximately 8' long .

    3. FIGURE 8 – Attachacornertruss(H)totheinsideofeachlighthangerverticalsupportupper(F)usingthepre-drilledholeslocated at the top of the support . Use the same bolt assembly stated in Step 3 of the Tray Stand assembly .

    4. FIGURE 9 – Positionthelighthangercrossbarassemblyontopof the truss supports and line up the pre-drilled holes located ontheendsofthebarandonthetrusses.(4)#1boltsand(4)nuts inserted from the top of the bar down through the truss will secure it in place .

    5. FIGURE 10 – Slide the upper light bar/cross bar assembly into the lowersupportbarsandlineuptheholes.Fastenwithsame#1bolt assembly as stated in the previous steps .

    The Active Aqua flood table stand should now be complete and ready to support a 4' x 8' Active Aqua flood table or Botanicare 4' x 8' (inside dimensions) tray, with the included spacer kit, and up to (3) complete light systems (2 if using the Raptor).

    ASSEMBLY INSTRUCTIONS, continued

    13

    F

    H

    FIGURE 81

    3

    FIGURE 9

    © Hydrofarm, Inc. v.3 10/2011 page 3

    42

    GFIGURE 6See page 8 for alternate view.

    1

    3

    F

    FIGURE 10See page 8 for alternate view.

    J

    E

    E1

    J

    3

    FIGURE 7

    HGSFT48 – Active Aqua 4' x 8' Flood Tray Stand

    Vérifiez hydrofarm.com pour la liste la plus récente de table d’inondations compatibles.

  • ESPECIFICACIONESDimensiones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4' X 8'Peso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 librasCapacidad de la barra de luz . . . . . . . . . . . . . . . . . . . . .Hasta 2 sistemas (dependiendo del tamaño/peso de los accesorios)

    HERRAMIENTAS NECESARIASLlave inglesa ajustable (13, 14 y 16mm)Una escalera y dos personas

    INSTRUCCIONES DE MONTAJEIMPORTANTE: Consulte la página 8 para obtener una visión general del montaje.SOPORTE DE LA BANDEJA1. Reúna las herramientas apropiadas necesarias para el montaje .

    Retiretodaslaspiezasdelembalajeycoloquelosaccesoriosaunlado .

    2.Agrupetodaslaspartesdeapoyojuntossegúneltipodefacilidaddelocalizaciónymontaje–p.ej.,laspatasjuntas,lasbarraslateralesjuntas,lasbarrasextremasjuntas,yasísucesivamente.

    3. FIGURA 1 – Conecte(1)cadaunodelosrefuerzosdebarraslaterales(B&I),juntosalolargo,con(1)pataAentrelasmismasaseguradascon(2)pernos#1y(2)tuercas.Elrefuerzodelabarracurva(I)vaenlaparteexteriordelaplacaplana.

    4. FIGURA 2 – Conecte(1)pataacadaextremodelmontajedelabarralateralusando(2)#1pernos(2)tuercas.Debehaberuntotalde(3)patasencadaladodemontajedelabarraderefuerzo.

    5.Repitalospasos3y4conelresto(2)delosrefuerzosdebarraslateralesylas(3)patas.

    6. FIGURA 3 – Una(1)elrefuerzoextremodelabarra(C)aunadelaspatasdemontajedebarralateralusando(2)#1tornillosy(2)tuercas . El montaje completo debe ser similar a una forma “L” .

    7. Repita el paso 6 usando el refuerzo de la barra extrema restante .

    NOTA: En este punto usted debe tener montados exitosamente (2) las estructuras principales que hacen el cuerpo del soporte de la bandeja.

    8. FIGURA 4 – Coloquelasdosestructurasjuntasusando(4)#1tornillosy(4)tuercas.Apartedelabarradesuspensióndeluzybarrasdeapoyo,elsoportedebeestarcompleto.

    9. Devueltaelladoderechodelsoporteasíestádepiesobrelasruedas móviles .

    FIGURE 1

    1

    A

    3B

    El soporte es más fácil de montar al revés.

    Asegúrese de que los orificios se encuentran en la barra inferior (mismo lado de ruedas).

    page 4

    HGSFT48 – Instrucciones de la Bandeja de Inundación 4' x 8' Active Aqua

    PIEZAS – SOPORTEA. Patas con ruedas móviles . . . . . . . . . . . .x 4B. Refuerzos de barra lateral (barra plana) .x 2C. Refuerzos de barras extremas . . . . . . . .x 2D. Barra de soporte de la bandeja . . . . . . .x 2E. Barra de suspensión de la luz . . . . . . . . .x 1F.Soporteverticaldesuspensión delaluz,superior . . . . . . . . . . . . . . . . . . .x 2

    G.Soporteverticaldesuspensiónde laluz,inferior (barra corta, fina) . . . . . . . . .x 2

    H. Viga de esquina de la barra de suspensión de la luz . . . . . . . . . . . . . . . .x 2

    I. Refuerzos de barra lateral (barra curva) . .x2J. Soporte central de la barra transversal

    de suspensión de luz . . . . . . . . . . . . . . . .x 1

    ACESSORIOS1. Tornillo de cabeza hexagonal de

    13 mm (⅜" x 1.8", 45 mm) . . . . . . . . . . . .x 28

    2. Tornillo de cabeza hexagonal de 13 mm (⅜" x 2.2", 55 mm) . . . . . . . . . . . .x 43. Tuercas (14 mm) . . . . . . . . . . . . . . . . . . .x 284. Tuerca ciega (16 mm) . . . . . . . . . . . . . . . . .x 45. Perno de soporte de la bandeja 3 .5" (90mm) . . . . . . . . . . . . . . . . . . . . . . .x46.Arandeladeplásticoparaelperno . . . . .x 47. Perno espaciador (para la bandeja 4' x 8' de Botanicare)* . . . . . . . . . . . . . . . .x 4* HGSFT44 solamente

    INSTRUCCIONES DE MONTAJE ES

    IVea el diagrama General de Montaje en la página 8 para una vista alternativa de los refuerzos de barra lateral plana (B) y curva (I).

    A

    31

    FIGURE 2FIGURE 3

    13C

    10. FIGURA 5 – Conectelos(4)soportesdelabandeja(D)perpendicular a lo largo del soporte de la bandeja . Los agujeros pre-perforados están en la parte superior de las barras inferiores de los refuerzos de barras laterales como semencionóenelpaso3.Use(8)#5pernos.SiutilizaunabandejaBotanicare(blanca),uselosespaciadores#7y#6arandelasdeplásticoincluidosparalevantarlossoportesdelabandeja(D)fueradelasbarrasinferioresdelosrefuerzosdebarraslaterales(B&I).

    BARRA DE SUSPENSIÓN DE LA LUZ1. FIGURA 6 – Conectelos(2)soportesverticalesdesuspensiónde

    laluzinferiores(G)alsoportedelabandejausandolosagujerospre-agujereados en el centro de los refuerzos de la barras extremas(C).Use(1)#2tornillosy(1)tuercaciegaporagujeropre-agujereado .

    2. FIGURA 7 – Ensamblelas(2)barrastransversalesdesuspensióndelaluz(E)juntas,usandoelapoyocentraldesuspensióndelaluz(J),(2)#1tornillosytuercas(2).Estemontajecompletodebe ser aproximadamente de 8 pies de largo .

    3. FIGURA 8 – Posicione la barra transversal de suspensión de la luz(F)enlapartesuperiordelsoportedevigas(H)yalineelosagujeros pre-agujereados ubicados en las barras extremas y en lasvigas.Inserteelmismoensamblaje#1deltornillocomoseindica en los pasos anteriores desde la parte superior de la barra para asegurarlas a las vigas .

    4. FIGURA 9 – Posicione el ensamblaje de la barra de suspensión de luz arriba de las vigas de apoyo y alinee los agujeros pre-perforados ubicados en los extremos de la barra y en las vigas . (4)pernos#1y(4)tuercasinsertadasdesdelapartesuperiordelabarrahaciaabajoatravésdelasvigaslofijaraensulugar.

    5. FIGURA 10 – Deslice la barra superior de la luz/ensamble la barra transversal en las barras de soporte inferior y alinee los agujeros.Sujeteconlosmismospernosdemontaje#1comoseindica en los pasos anteriores .

    El soporte de la mesa de inundación de Active Aqua ahora debe ser completo y listo para apoyar una mesa de inundación Active Aqua de 4' x 8' o una bandeja Botanicare de 4' x 8', con el equipo separador incluido, y hasta (3) sistemas de luz completos (2 si se utiliza el Raptor).

    INSTRUCCIONES DE MONTAJE – Soporte de la Bandeja, continuado

    13

    F

    H

    FIGURE 81

    3

    FIGURE 9

    © Hydrofarm, Inc. v.3 10/2011 page 5

    13

    F

    FIGURE 10

    Vea la página 8 para una vista alternativa.

    J

    E

    E

    1

    J

    3

    FIGURE 7

    HGSFT48 – Instrucciones de la Bandeja de Inundación 4' x 8' Active Aqua

    D

    56

    Vea la página 8 para una vista alternativa.

    FIGURE 5

    42

    G

    Vea la página 8 para una vista alternativa.

    FIGURE 6

    FIGURE 4

    1

    3

    NOTA: Los soportes de la bandeja deben ser instalados encima de las barras de los soporte inferiores del refuerzo de barras laterales. Estos proporcionan un soporte estructural para las bandejas de inundaciones por lo que no hay fluctuación en el equilibrio de la bandeja.

    Compruebe en www.hydrofarm.com para saber si hay la lista más hasta la fecha de bandejas compatibles.