4x00 6x00 8x00 Enterprise Virtual Array Setup Guide

HP StorageWorks4x00/6x00/8x00 Enterprise Virtual Arrayhardware configuration guide

Part number: 5697-7338Fifth edition: February 2008

Legal and notice information

Copyright 2005-2008 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forthin the express warranty statements accompanying such products and services. Nothing herein should be construed as constitutingan additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Contents

About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . 9Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Document conventions and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Rack stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10HP technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Customer self repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Product warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Subscription service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11HP websites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Documentation feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1 EVA 4x00/6x00/8x00 hardware . . . . . . . . . . . . . . . . . 13Storage rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

36U rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1342U rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Fibre Channel drive enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Fibre Channel loop switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14EVA8x00 HSV210-A/B controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16EVA6x00 and EVA4x00 HSV200-A/B controllers . . . . . . . . . . . . . . . . . . . . . . . 17

2 EVA8x00 configurations . . . . . . . . . . . . . . . . . . . . . 192C2D configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192C6D configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232C12D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3 EVA6x00 configurations . . . . . . . . . . . . . . . . . . . . . 312C4D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312C5D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332C6D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352C7D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372C8D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4 EVA4x00 configurations . . . . . . . . . . . . . . . . . . . . . 432C1D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432C2D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452C3D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472C4D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

A Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 53Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

B Low-voltage Japanese cabinets . . . . . . . . . . . . . . . . . . 59General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

4x00/6x00/8x00 Enterprise Virtual Array hardware configuration guide 3

Power configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

EVA cabinet footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Weights and dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Center of gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Tip stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4

Figures1 FC drive enclosurefront and rear views . . . . . . . . . . . . . . . . . . . . . . 142 30-10022-01 FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3 30-10010-02 FC loop switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 HSV210/200 controllerfront view . . . . . . . . . . . . . . . . . . . . . . . . 165 HSV210-A/B controllerrear view . . . . . . . . . . . . . . . . . . . . . . . . 17

6 HSV200-A/B controllerrear view . . . . . . . . . . . . . . . . . . . . . . . . 187 2C2D Storage-Centric configuration . . . . . . . . . . . . . . . . . . . . . . . . 19

8 EVA8x00 2C2D Storage-Centric cable diagram . . . . . . . . . . . . . . . . . . . 20

9 2C2D Multi-Product configuration . . . . . . . . . . . . . . . . . . . . . . . . . 21

10 EVA8x00 2C2D Multi-Product cable diagram . . . . . . . . . . . . . . . . . . . . 22

11 2C6D Storage-Centric configuration . . . . . . . . . . . . . . . . . . . . . . . . 23

12 EVA8x00 2C6D Storage-Centric configuration cable diagram . . . . . . . . . . . . . 24

13 2C6D Multi-Product configuration . . . . . . . . . . . . . . . . . . . . . . . . . 25

14 EVA8x00 2C6D Multi-Product configuration cable diagram . . . . . . . . . . . . . . 26

15 2C12D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

16 EVA8x00 2C12D cable diagram . . . . . . . . . . . . . . . . . . . . . . . . . 28

17 2C4D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

18 EVA6x00 2C4D cable diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 32


















35 HP StorageWorks 42U low-voltage cabinet . . . . . . . . . . . . . . . . . . . . . 60


37 EVA cabinet footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6

Tables1 Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Maximum storage capacities for the 2C2D configuration . . . . . . . . . . . . . . . 23

4 Maximum storage capacities for the 2C6D configuration . . . . . . . . . . . . . . . 27

5 Maximum storage capacities for the 2C12D configuration . . . . . . . . . . . . . . 29






11 Maximum storage capacities for the EVA4x00 2C1D configuration . . . . . . . . . . 44




15 Enterprise Virtual Array 4x00/6x00/8x00 Product Dimensions, Weight and Clearance . . 53

16 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

17 Enterprise storage system AC input line voltages . . . . . . . . . . . . . . . . . . . 54

18 Power Data (North America/Europe/Japan) maximum configuration . . . . . . . . . . 55

19 EVA4x00 power specifications 208 Volts . . . . . . . . . . . . . . . . . . . . 55







26 HP StorageWorks 36U low-voltage cbinet . . . . . . . . . . . . . . . . . . . . . 61

27 Center of gravity measurements 42U low-voltage cabinet . . . . . . . . . . . . . . 62

28 Center of gravity measurements 36U low-voltage cabinet . . . . . . . . . . . . . . 62


About this guide

This hardware configuration guide provides information to help you:

Learn about the Enterprise Virtual Array hardware components. Understand the supported storage rack configurations. Understand the supported copper cable configurations.

Intended audienceThis book is intended for use by Enterprise Virtual Array customers involved in the installation, operation,and management of the EVA 4x00/6x00/8x00 storage systems and who are experienced with thefollowing:

SANs and storage systems. Networking and virtual storage concepts. Enterprise Virtual Array products.

Related documentationAdditional documentation is available from the HP website at http://www.hp.com/support/manuals.

Select Disk Storage Systems from Storage, and then select either HP StorageWorks 4000/6000/8000Enterprise Virtual Arrays or HP StorageWorks 4100/6100/8100 Enterprise Virtual Arrays from EVADisk Arrays.

Document conventions and symbolsTable 1 Document conventions

Convention Element

Blue text: Table 1 Cross-reference links and e-mail addresses

Blue, underlined text: http://www.hp.com website addresses

Bold text

Keys that are pressed Text typed into a GUI element, such as a box GUI elements that are clicked or selected, such as

menu and list items, buttons, tabs, and check boxes

Italic text Text emphasis

Monospace text

File and directory names System output Code Commands, their arguments, and argument values

Monospace, italic text Code variables Command variables

Monospace, bold text Emphasized monospace text


WARNING!Indicates that failure to follow directions could result in bodily harm or death.

CAUTION:Indicates that failure to follow directions could result in damage to equipment or data.

IMPORTANT:Provides clarifying information or specific instructions.

NOTE:Provides additional information.

TIP:Provides helpful hints and shortcuts.

Rack stabilityRack stability protects personnel and equipment.

WARNING!To reduce the risk of personal injury or damage to equipment: Extend leveling jacks to the floor. Ensure that the full weight of the rack rests on the leveling jacks. Install stabilizing feet on the rack. In multiple-rack installations, fasten racks together securely. Extend only one rack component at a time. Racks can become unstable if more than one component

is extended.

HP technical supportFor worldwide technical support information, see the HP support website:

http://www.hp.com/support

Before contacting HP, collect the following information:

Product model names and numbers Technical support registration number (if applicable) Product serial numbers Error messages Operating system type and revision level Detailed questions

10 About this guide

Customer self repairHP customer self repair (CSR) programs allow you to repair your StorageWorks product. If a CSRpart needs replacing, HP ships the part directly to you so that you can install it at your convenience.Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a repaircan be accomplished by CSR.

For more information about CSR, contact your local service provider. For North America, see the CSRwebsite:

http://www.hp.com/go/selfrepair

This product has no customer replaceable components.

Product warrantiesFor information about HP StorageWorks product warranties, see the warranty information website:

http://www.hp.com/go/storagewarranty

Subscription serviceHP recommends that you register your product at the Subscriber's Choice for Business website:

http://www.hp.com/go/e-updates

After registering, you will receive e-mail notification of product enhancements, new driver versions,firmware updates, and other product resources.

HP websitesFor additional information, see the following HP websites:

http://www.hp.com http://www.hp.com/go/storage http://www.hp.com/service_locator

Documentation feedbackHP welcomes your feedback.

To make comments and suggestions about product documentation, please send a message [email protected]. All submissions become the property of HP.


12 About this guide

1 EVA 4x00/6x00/8x00 hardware

This chapter discusses the hardware components in the Enterprise Virtual Array (EVA). The followingtopics are discussed:

Storage rack Fibre Channel drive enclosures Fibre Channel loop switches EVA8x00 HSV210-A/B controllers EVA6x00 and EVA4x00 HSV200-A/B controllers

Storage rackRacks are available for the EVA storage system in 36U and 42U configurations. The storage rack canhold a maximum of 12 Fibre Channel (FC) drive enclosures and two controllers.

36U rackThe 36U rack is graphite in color and 1000 mm (39.4 inches) deep. The 19inch (482.6 mm)industry-standard rack provides an enclosure for rack-mountable products with a height capacity of 36U.Perforated front and back doors are included, and 36U side panels and stabilizer kits are optional.

42U rackThe 42U rack is graphite in color and 909 mm (35.8 inches) deep. The storage rack features standard19inch (482.6 mm) mounting rails. The 42U rack can support Enterprise Virtual Array configurationsthat include FC loop switches or expansion panels. Perforated front and back doors are included, and42U side panels and stabilizer kits are optional.

Fibre Channel drive enclosuresEach FC drive enclosure includes the following features:

3U drive enclosure Dual redundant, active-to-active, 2Gbps Fibre Channel loops Fourteen 1inch Fibre Channel disks per enclosure Dual 2Gbps Fibre Channel I/O moduleA and B

Enhanced fault detection Small Form-Factor Pluggables (SFPs)

Dual 500W redundant hot-plug power supplies and fans

For ease of reference, the disk drives are usually referred to by their physical location in the drive bay.

Figure 1 shows the front and rear views of the FC drive enclosure and the physical location of eachdrive bay.


0112a

Front

Rear

1 2

3 4 56 78 9

1010

Figure 1 FC drive enclosurefront and rear views

1. Drive bay 1 2. Drive bay 14

3. EMU 4. I/O module B

5. Blower 1 6. Power supply 1

7. Blower 2 8. Power supply 2

9. I/O module A 10. Status indicators (EMU, enclosure power,enclosure fault)

Fibre Channel loop switchesThe Enterprise Virtual Array uses FC loop switches to connect all of the drive enclosures to the controllerpair via copper cables. Each FC loop switch acts as a central point of interconnection and establishes aphysical loop topology.

Switch use:

EVA4000/4100 does not use switches on any configuration EVA6000/6100 uses switches on all configurations EVA8000/8100 only uses switches with more than four disk enclosures

The storage system uses one of the following loop switches:

30-10022-01 loop switchused with 2 Gb and 4 Gb controllers (required on EVA4100/6100/8100)

30-10010-02 loop switchused with 2 Gb and 4 Gb controllers

CAUTION:When using the 30-10022-01 loop switch, ensure that there is no disk in bays 12, 13, and 14 inenclosures 17, 20, and 24. Slots 13 and 14 are assigned the same ALPA as the controllers and slot12 is assigned ALPA 4, which is taken by the 30-10022-01 loop switch. Failure to adhere to this rulewill disrupt storage system operation. HP also recommends that you keep three additional bays opento maintain the maximum device count of 120. For ease of use and consistency in configurations, HPrecommends keeping bays 12, 13, and 14 open in enclosures 16 and 19.

The major features of the FC loop switch are:

2.125 Gbps operating speed


Twelve ports Half-width, 1U size System and port status indicators An Ethernet port Universal power supply that operates between 100 to 250 VAC (or 50 to 60 Hz) SFP transceivers

Figure 2 shows the rear view of the 30-10022-01 Fibre Channel loop switch.

FAULT

POWER

TEMP

10101

1 2 3 4 5 6

7 8 9 10 11 12

100-240V~, 50/60 HZ

1 2 3 4

Figure 2 30-10022-01 FC loop switch

1. Ethernet activity 2. Ethernet link

3. Port status 4. System status

Figure 3 shows the front and rear views of the 30-10010-02 Fibre Channel loop switch.

344

4242

3

1

65 7 8 9 10

Figure 3 30-10010-02 FC loop switch

1. Handle 2. Bezel snaps

3. Alignment tabs 4. Walk-up RS-232 port

5. SFP status indicator 6. Port Bypassed indicator

7. POST fault indicator 8. Over Temp indicator

9. Power indicator 10. Loop operational indicator


EVA8x00 HSV210-A/B controllersTwo high-performance HSV210 controllers are included in each EVA8x00 rack. The EVA8000 controlleris identified as HSV210-A and the EVA8100 controller is identified as HSV210-B. Each controller iscontained in a separate enclosure and provides the following features:

High-performance PowerPC microprocessor An Operator Control Panel (OCP) for easy operation 4U rack space required for both controller enclosures Four 4Gbps Fibre Channel-Switched Fabric host ports Four 2Gbps FC-AL device ports

Arranged in redundant pairs Data load/performance balanced across a pair Supports up to 240 disks (120 disks per pair)

2 GB cache per controller, mirrored, with battery backup 2 Gbps FC cache mirroring port with device port backups Two mirror ports Dual power supplies

The controller is the interface between HP StorageWorks Command View EVA and the EnterpriseVirtual Array (the interface between hosts and disks). Up to 18 drive enclosures are supported byone HSV210-A/B controller pair (two controllers).

Figure 4 shows the front of the controller. Figure 5 shows the controller rear view.

1

2

3

4

6

5 7

6

4

Figure 4 HSV210/200 controllerfront view

1. Battery 0 2. Battery 1 (EVA8x00 only)

3. Blower 0 4. Blower 1

5. Operator Control Panel (OCP) 6. Status indicators

7. Unit ID


1 2 3 4

85675 6

10

9

Figure 5 HSV210-A/B controllerrear view

1. Dual controller interconnect 2. CAB (cabinet address bus)

3. Unit ID 4. Power ON switch

5. FC device ports 6. FC cache mirror ports

7. FC host ports 8. Power supply 0

9. Power supply 1 10. Service connectors (not for customer use)

EVA6x00 and EVA4x00 HSV200-A/B controllersTwo high-performance HSV200 controllers are included in each EVA6x00 and EVA4x00 storage system.The EVA4000/6000 controllers are identified as HSV200-A. The EVA4100/6100 controllers areidentified as HSV200-B. Each controller is installed in a separate enclosure and provides the followingfeatures:

High-performance, PowerPC microprocessor An Operator Control Panel (OCP) for easy operation 4U rack space required for both controller enclosures Two 4Gbps, FC-Switch Fabric host ports Two 2Gbps, FC-AL device ports

Arranged as a single redundant pair Data load/performance balanced across a pair Support for up to 112 drives

1 GB cache per controller, mirrored, with battery backup 2 Gbps, FC cache mirroring port with device port backups

Each HSV200-A/B controller supports four drive enclosures on the EVA4x00, and eight drive enclosureson the EVA6x00. Figure 4 shows the front of the controller. Figure 6 shows the controller rear view.


8 957 65 6

1 2 3 410

Figure 6 HSV200-A/B controllerrear view

1. Dual controller interconnect 2. CAB (cabinet address bus)

3. Unit ID 4. Power ON switch

5. FC device ports 6. FC cache mirror ports

7. FC host ports 8. Power supply 0

9. Power supply 1 10. Service connectors (not for customer use)


2 EVA8x00 configurations

This chapter discusses the standard EVA8x00 configurations. Each section describes the placement ofHSV controllers, drive enclosures, enclosure address bus shelf ID expansion cables, and copper FibreChannel cables.

NOTE:The configurations described in this guide are the preferred configurations. Other configurations may beused, but they should conform to the following: Disk enclosures should be balanced across the two back-end loop pairs. Use of enclosure ID 7 for disk enclosures is not allowed.

2C2D configurationsThere are two 2C2D configurations: the Storage-Centric (Figure 7) and the Multi-Product (Figure 9). Eachconfiguration provides a maximum storage capacity of 8.4 TB and can contain a maximum of 28 disks.These configurations are available in a 42U rack and have two HSV210-A/B controllers and two driveenclosures. The Storage-Centric configuration can be expanded (by adding drive enclosures) whileremaining online. The Multi-Product more easily allows multiple products to be racked with the EVA, butcan only be expanded by powering it down to make these expansion modifications.

16358

1

3

2

1

Figure 7 2C2D Storage-Centric configuration

1. Drive enclosure2. HSV210-A/B controller pair3. 3U blank

The 2C2D Storage-Centric configuration cable routing diagram is located in Figure 8.


50178c

1

2

6

7

3

3

4

Figure 8 EVA8x00 2C2D Storage-Centric cable diagram

1. ID port 142. Top terminator3. Drive enclosure4. HSV210-A/B controller pair5. Bottom terminator6. Y cable7. Dual controller interconnect cable


16354Mai n 1 2 3 4

Mai n 1 2 3 4

2

3

2

4

1

Figure 9 2C2D Multi-Product configuration

1. 3U blank2. Drive enclosure3. HSV210-A/B controller pair4. Power distribution units

The 2C2D Multi-Product configuration cable routing diagram is located in Figure 10.


16357

6

2

1

4

5

3 7

6

8

Figure 10 EVA8x00 2C2D Multi-Product cable diagram

1. Top terminator2. ID port 63. Y cable4. Dual controller interconnect cable5. Bottom terminator6. Drive enclosure7. HSV210-A/B controller pair8. Power distribution units

2C2D featuresThe following features are included in the 2C2D:

One storage rack Two controllers Two 14drive bay FC drive enclosures Seven 2port enclosure address bus shelf ID expansion cables Eight AC strips Two 0U PDUs in Storage-Centric configuration; two 1U PDUs in Multi-Product configuration

NOTE:Disks must be ordered separately.


Table 3 Maximum storage capacities for the 2C2D configuration

Disk size Maximumcapacity

72 GB 2.0 TB

146 GB 4.0 TB

250 GB 7.0 TB

300 GB 8.4 TB

500 GB 14.0 TB

2C6D configurationsThere are two 2C6D configurations: the Storage-Centric (Figure 11) and the Multi-Product (Figure 13).Each configuration provides a maximum storage capacity of 25.2 TB and contains a maximum of 84disks. These configurations are available in a 42U rack and have two loop switches, two HSV210-A/Bcontrollers, and six drive enclosures. The Storage-Centric configuration can be expanded (by adding driveenclosures) while remaining online. The Multi-Product more easily allows multiple products to be rackedwith the EVA, but can only be expanded by powering it down to make these expansion modifications.

16359

1

3

2

2

4

Figure 11 2C6D Storage-Centric configuration

1. 3U blank2. Drive enclosures3. FC switches4. HSV210-A/B controller pair

The 2C6D Storage-Centric configuration cable routing diagram is located in Figure 12.


12

3

4

5

4

36

7

8

0177b

Figure 12 EVA8x00 2C6D Storage-Centric configuration cable diagram

1. ID port 142. Top terminator3. Drive enclosure4. FC switches5. HSV210-A/B controller pair6. Bottom terminator7. Y cable8. Dual controller interconnect cable


16355

2

2

3

4

5

3

1

Figure 13 2C6D Multi-Product configuration

1. 3U blank2. Drive enclosures3. FC switches4. HSV210-A/B controller pair5. Power distribution units

The 2C6D Multi-Product configuration cable routing diagram is located in Figure 14.


16356

1

2

3

4

5

6

6

7

8

9

7

Figure 14 EVA8x00 2C6D Multi-Product configuration cable diagram

1. Top terminator2. ID port 83. Dual controller interconnect cable4. Y cable5. Bottom terminator6. Drive enclosures7. FC switches8. HSV210-A/B controller pair9. Power distribution units

2C6D featuresThe following features are included in the 2C6D:

One storage rack Two controllers Six 14drive bay FC drive enclosures Four FC loop switches Seven 2port enclosure address bus shelf ID expansion cables Eight AC strips Two 0U PDUs in Storage-Centric configuration; two 1U PDUs in Multi-Product configuration


The 2C6D configuration can contain 84 disk drives has and a maximum storage capacity of 25.2TB. See Table 4.




72 GB 6.0 TB

146 GB 12.0 TB

250 GB 21.0 TB

300 GB 25.2 TB

500 GB 42.0 TB

2C12D configurationThe 2C12D configuration provides a maximum storage capacity of 50.4 TB. This configuration cancontain a maximum of 168 disks. This configuration is available in a 42U rack and has two HSV210-A/Bcontrollers, twelve drive enclosures, and four loop switches.

16360

2

1

1

1

1

3

Figure 15 2C12D configuration

1. Drive enclosures2. FC switches3. HSV210-A/B controller pair

The 2C12D cable routing diagram is located in Figure 16.


0165b

1

2 3

4

5

4

36

7

8

Figure 16 EVA8x00 2C12D cable diagram

1. ID port 142. Top terminator3. Drive enclosure4. FC switches5. HSV210-A/B controller pair6. Bottom terminator7. Y cable8. Dual controller interconnect cable

2C12D featuresThe following features are included with the 2C12D configuration:

One storage rack Two controllers 12 14drive bay FC drive enclosures Four FC loop switches Seven 2port enclosure address bus shelf ID expansion cables Eight AC strips Two 0U PDUs





72 GB 12.0 TB

146 GB 24.0 TB

250 GB 42.0 TB

300 GB 50.4 TB

500 GB 84.0 TB



This chapter discusses the standard EVA6x00 configurations. Each section describes the placement ofHSV controllers, drive enclosures, enclosure address bus shelf ID expansion cables, and copper FibreChannel cables.

NOTE:The configurations described in this guide are the preferred configurations. Other configurations may beused, but ensure that enclosure ID 7 is not used for any disk enclosure.

2C4D configurationThe 2C4D configuration provides a maximum storage capacity of 16.8 TB. This configuration can containa maximum of 56 disks. This configuration is available in a 42U, 41U, 36U, 33U, 25U, or 22U rack andhas two HSV200-A/B controllers, four drive enclosures, and two loop switches.


1. 3U blank2. FC switches3. HSV200-A/B controller pair4. Drive enclosures



0170b

1

2

3

4

5

6

7

8


1. FC switches2. HSV200-A/B controller pair3. Drive enclosure4. Bottom terminator5. Dual controller interconnect cable6. Y cable7. ID port 108. Top terminator


One storage rack Four 14drive bay FC drive enclosures One pair of FC-AL loop switches One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 4.0 TB

146 GB 8.1 TB

250 GB 14.0 TB

300 GB 16.8 TB

500 GB 28.0 TB

2C5D configurationThe 2C5D configuration provides a maximum storage capacity of 21.0 TB. This configuration can containa maximum of 70 disks. This configuration is available in a 42U, 41U, 36U, 33U, 25U, or 22U rack andhas two HSV200-A/B controllers, five drive enclosures, and two loop switches.


1. 3U blank2. Drive enclosures3. Switch4. HSV200-A/B controller pair



0169b

1

1

2

3

4

5

6

7

8


1. Drive enclosure2. FC switches3. HSV200-A/B controller pair4. Bottom terminator5. Dual controller interconnect cable6. Y cable7. ID port 108. Top terminator


One storage rack Five 14drive bay FC drive enclosures One pair of FC-AL loop switches One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 5.0 TB

146 GB 10.0 TB

250 GB 17.5 TB

300 GB 21.0 TB

500 GB 35.0 TB

2C6D configurationThe 2C6D configuration provides a maximum storage capacity of 25.2 TB. This configuration can containa maximum of 84 disks. This configuration is available in a 42U, 41U, 36U, 33U, or 25U rack, and hastwo HSV200-A/B controllers, six drive enclosures, and four loop switches.





0168b

1

1

2

3

4

5

6

7

8




One storage rack Six 14drive bay FC drive enclosures One pair of FC-AL loop switches One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 6.0 TB

146 GB 1.0 TB

250 GB 21.0 TB

300 GB 25.2 TB

500 GB 42.0 TB

2C7D configurationThe 2C7D configuration provides a maximum storage capacity of 29.4 TB. This configuration can containa maximum of 98 disks. This configuration is available in a 42U, 41U, 36U, or 33U rack and has twoHSV200-A/B controllers, seven drive enclosures, and two loop switches.





0167b

1

1

2

3

4

5

6

7

8




One storage rack Seven 14drive bay FC drive enclosures One pair of FC-AL loop switches One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 7.0 TB

146 GB 14.0 TB

250 GB 24.5 TB

300 GB 29.4 TB

500 GB 49.0 TB

2C8D configurationThe 2C8D configuration provides a maximum storage capacity of 33.6 TB. This configuration can containa maximum of 112 disks. This configuration is available in a 42U, 41U, 36U, or 33U rack and has twoHSV200-A/B controllers, eight drive enclosures, and two loop switches.





0166b

1

2

3

14

5

6

7

8




One storage rack Eight 14drive bay FC drive enclosures One pair of FC-AL loop switches One 2port enclosure address bus cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 8.0 TB

146 GB 16.0 TB

250 GB 28.0 TB

300 GB 33.6 TB

500 GB 56.0 TB



This chapter briefly discusses the standard EVA4x00 configurations. Each section describes the placementof HSV controllers, drive enclosures, enclosure address bus shelf ID expansion cables, and copperFibre Channel cables.

NOTE:The configurations described in this guide are the preferred configurations. Other configurations may beused, but ensure that enclosure ID 7 is not used for any disk enclosure.

2C1D configurationThe 2C1D configuration provides a maximum storage capacity of 4.2 TB. This configuration can containa maximum of 14 disks. This configuration is available in a 42U, 41U, 36U, 33U, 25U, or 22U rack andhas two HSV200-A/B controllers and one drive enclosure.


1. 3U blank2. HSV200-A/B controller pair3. Drive enclosure



Figure 28 EVA4x00 2C1D cable diagram1. HSV200-A/B controller pair2. Drive enclosure3. Bottom terminator4. Dual controller interconnect cable5. Y cable6. ID port 67. Top terminator


One storage rack One 14drive bay FC drive enclosures One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)


Table 11 Maximum storage capacities for the EVA4x00 2C1D configuration


72 GB 1 TB

146 GB 2 TB

250 GB 3.5 TB

300 GB 4.2 TB

500 GB 7.0 TB


2C2D configurationThe 2C2D configuration provides a maximum storage capacity of 8.4 TB. This configuration can containa maximum of 28 disks. This configuration is available in a 42U, 41U, 36U, 33U, 25U, or 22U rack andhas two HSV200-A/B controllers and two drive enclosures.


1. 3U blank2. HSV200-A/B controller pair3. Drive enclosures



10173b

2

23

4

5

6

7


1. HSV200-A/B controller pair2. Drive enclosure3. Bottom terminator4. Dual controller interconnect cable5. Y cable6. ID port 67. Top terminator


One storage rack Two 14drive bay FC drive enclosures One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)




72 GB 2.0 TB

146 GB 4.0 TB

250 GB 7.0 TB

300 GB 8.4 TB

500 GB 14.0 TB


2C3D configurationThe 2C3D configuration provides a maximum storage capacity of 12.6 TB. This configuration can containa maximum of 42 disks. This configuration is available in a 42U, 41I, 36U, 33U, 25U, or 22U rackand has two HSV200-A/B controllers and three drive enclosures.



The 2C3D cable routing diagram is located in Figure 32


0172b

1

2

23

4

5

6

7




One storage rack Three 14drive bay FC drive enclosures One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)



Disk Size MaximumCapacity

72 GB 3.0 TB

146 GB 6.1 TB

250 GB 10.5 TB

300 GB 12.6 TB

500 GB 21.0 TB


2C4D configurationThe 2C4D configuration provides a maximum storage capacity of 16.8 TB. This configuration cancontain a maximum of 56 disks. This configuration is available in a 42U, 41U, 36U, 33U, 25U, or 22Urack and has two HSV200-A/B controllers and four drive enclosures.





0171b

1

2

23

4

5

6

7




One storage rack Four drive bay FC drive enclosures One 2port enclosure address bus shelf ID expansion cable Six AC strips Two 1U PDUs (not shown in figure)





72 GB 4.0 TB

146 GB 8.0 TB

250 GB 14.0 TB

300 GB 16.8 TB

500 GB 28.0 TB


A Specifications

This appendix defines the physical, environmental, and power specifications of the EVA4x00/6x00/8x00 storage systems.

The following topics are included:

Physical specifications Environmental specifications Power specifications

Physical specificationsThis section describes the physical specifications of the drive enclosure and elements.

Table 15 defines the dimensions and weights of the storage system components.

Table 15 Enterprise Virtual Array 4x00/6x00/8x00 Product Dimensions, Weightand Clearance

PhysicalDimensions

Heightin/cm

Widthin/cm

Depthin/cm

MaxWeightlb/kg

Req. FrontClearancein/cm

Req. RearClearancein/cm

EVA4x00/8x002C2D (42U rack)

78.75(200.03) 23.7 (60.3)

40.2(102.2)

537(244.1) 30 (76.2) 30 (76.2)

EVA6x00/8x002C6D (42U rack)

78.75(200.03) 23.7 (60.3)

40.2(102.2)

854(308.2) 30 (76.2) 30 (76.2)

EVA8x00 2C12D(42U rack)

78.75(200.03) 23.7 (60.3)

40.2(102.2)

1290(586.4 30 (76.2) 30 (76.2)

EVA4x00/6x00/8x00 ControllerAssembly

7.0/17.78 17.6/44.70 27.5/69.85 120/54.55 N/A N/A

M5314B/M5314C DriveEnclosure

5.25/13.34

19.0/42.26 20/50.8 71/32.21 N/A N/A

Environmental specificationsTo ensure optimum product operation, you must maintain the operational environmental specificationslisted in Table 16. The ambient temperature (the enclosure air intake or room temperature) is especiallycritical.


Table 16 Environmental specifications

Operating Temperature 50 to 95 F (10 to 35 C) - Reduce rating by 1 F for each 1000 ft altitude(1.8 C/1,000 m)

Shipping Temperature -40 to 150 F (-40 to 66 C)

Humidity 10% to 90% non-condensing

Shipping Humidity 5% to 90% non-condensing

Altitude Up to 8,000 ft (2,400 m)

Air Quality Not to exceed 500,000 particles per cubic foot of air at a size of 0.5 micronor larger

Power specificationsThe input voltage is a function of the country-specific input voltage to Enterprise storage system rackpower distribution units (PDUs). Enterprise storage system AC input line voltages defines the AC inputpower available to the drive enclosure power supplies.

CAUTION:The AC power distribution within a rack ensures a balanced to each PDA and reduces the possibility ofan overload condition. Changing the cabling to or from a PDM could cause an overload condition.

Table 17 Enterprise storage system AC input line voltages

Specification Minimal Nominal Maximum

60 Hz service

AC Line Voltage 57 Hz 60 Hz 63 Hz

AC Line VoltageJapan 180 VAC 202 VAC 220 VAC

AC Line VoltageNorth America 180 VAC 208 VAC 220 VAC

AC Line VoltageEurope 208 VAC 240 VAC 254 VAC

50 Hz service

AC Line Frequency 47 Hz 50 Hz 53 Hz

AC Line VoltageJapan 180 VAC 202 VAC 220 VAC



AC Line VoltageEurope 208 VAC 240 VAC 254 VAC

54 Specifications

Table 18 Power Data (North America/Europe/Japan) maximum configuration

AC plug type (quantity 2)North America 3 wire NEMA No. L6-30P, 30 amp (208 to 240V, 5060Hz,30A)Europe 3 wire, 2 pole IEC 309, 30 amp, (220 to 240V, 50Hz, 32A)

Number of phases Single

Rated current 17A @ 200V-240V AC, 60Hz total, 4.25 A per power cord

Nominal Line VoltageNorth America 208 or 230VEurope 230VJapan 206V

Range Line Voltage 187 to 256V

Line Frequency North America 60Hz, Europe 50Hz, Japan 50 or 60 Hz

Table 19 EVA4x00 power specifications 208 Volts

Specification 2C1D 2C2D 2C3D 2C4D

Total SystemWattage 638 1013 1390 1767

Total SystemBTU/hour 1729 3014 4300 5585

Input Current (A) -Typical per system 1.6 2.6 3.5 4.4

Typical1

In Rush Current (A) 98 132 170 220

Failover ModeInput Current (A)- Maximum persystem

2.7 4.3 5.9 7.5

1 Typical is described as a system in normal steady state operation (that is, both PDUs operating normally, the arrayreading/writing to disk drives in a production environment).

This data represents fully populated drive enclosures with 15K RPM disk drives. Other drive types may vary slightly. For example, ifyou are using 10K RPM drives, the power specifications will be approximately 20% less than the 15K RPM drives.


Specification 2C1D 2C2D 2C3D 2C4D

Total SystemWattage 638 1013 1390 1767

Total SystemBTU/hour 1729 3014 4300 5585

Input Current (A) -Typical per system 1.5 2.4 3.3 4.2

Typical1

In Rush Current (A) 104 147 190 244

Failover ModeInput Current (A)- Maximum persystem

2.6 4.1 5.5 7.1





Specification 2C4D 2C5D 2C6D 2C7D 2C8D

Total SystemWattage 1837 2214 2590 2967 3344

Total SystemBTU/hour 6268 7553 8838 10124 11409

Input Current(A) - Typicalper system

4.6 5.5 6.5 7.4 8.4Typical1

In Rush Current(A) 220 250 280 321 363

Failover ModeInput Current(A) - Maximumper system

7.8 9.4 11.0 12.6 14.2








4.3 5.2 6.1 7.0 7.9Typical1

In Rush Current(A) 244 272 311 357 403


7.3 8.8 10.0 11.9 13.3



56 Specifications






2.9 6.7 8.5 10.4 12.3Typical1

In Rush Current(A) 132 280 363 451 528


4.9 11.3 14.5 17.7 20.8








2.7 6.3 8.1 9.8 11.6Typical1

In Rush Current(A) 147 311 403 500 586


4.6 10.6 13.7 16.7 19.7


This data represents fully populated drive enclosures with 15K RPM disk drives. Other drive types may vary slightly.


58 Specifications

B Low-voltage Japanese cabinets

General descriptionThis specification describes HP's requirements for low voltage EVA storage cabinets. These low voltagecabinets are configured with two redundant sets of PDUs in order to provide system required power. EachPDU set is limited to 2550 W at a minimum voltage of 108. Each PDU is limited to one power stripto limit the number of EVA component attachment to eight components per power PDU. Power stripadditions will likely overload the PDU systems.

Reference documentsReference documents are for informational purposes only. No requirement is implied by the inclusionor exclusion of reference documents.

ANSI/EIA-310-D-1992, Cabinets, Racks, Panels and Associated Equipment EN60950:2000, Safety of Information Technology Equipment FCC Part 15 Code of Federal Regulations, Title 47, FCC Part 15 Radio Frequency Devices,

Subpart B, Unintentional Radiators EN55022 (1998), Limits and Methods of Measurement of Radio Interference Characteristics of

Information Technology Equipment EN55024 (1998), Information Technology Equipment Immunity Characteristics and Methods

of Measurement EN61000, Electromagnetic Compatibility CAN/CSA-C22.2 No. 60950-00/3rd Edition, Safety of Information Technology Equipment

All brands, names, trademarks and logos are the property of their respective owners.

Power configurationsThere are two power configurations: the AD572A and the AD573A. The AD572A uses the HPStorageWorks 42U Low-voltage cabinet (Figure 35) and the AD573A uses the HP StorageWorks 36ULow-voltage cabinet (Figure 36).


42 U41 U40 U39 U38 U37 U36 U35 U34 U33 U32 U31 U30 U29 U28 U27 U26 U25 U24 U23 U22 U21 U20 U19 U18 U17 U16 U15 U14 U13 U12 U11 U10 U09 U08 U07 U06 U05 U04 U03 U02 U01 U

0156a

Figure 35 HP StorageWorks 42U low-voltage cabinet

36 U35 U34 U33 U32 U31 U30 U29 U28 U27 U26 U25 U24 U23 U22 U21 U20 U19 U18 U17 U16 U15 U14 U13 U12 U11 U10 U09 U08 U07 U06 U05 U04 U03 U02 U01 U

0157a

Figure 36 HP StorageWorks 36U low-voltage cabinet

SpecificationsThis section contains information on:

EVA cabinet footprint Weights and dimensions of the low-voltage cabinets Center of gravity and stability Torque specifications Environmental specifications Electrical specifications

60 Low-voltage Japanese cabinets

EVA cabinet footprintFigure 37 shows the dimensions of the EVA cabinet footprint.

0158a

60.96"60.96" 37.46"

23.73"

90

Figure 37 EVA cabinet footprint

Weights and dimensionsTable 25 shows the weights and dimensions for the 42U low-voltage cabinet. Table 26 shows thesame information for the 36U low-voltage cabinet.

Table 25 HP StorageWorks 42U low-voltage cabinet

Weight lbs Height in Width in Depth in

Assembly 254 78.85 23.73 40.22

Packaged Assy 367 84.63 35.50 46.50

Table 26 HP StorageWorks 36U low-voltage cbinet

Weight lbs Height in Width in Depth in

Assembly NA 68.35 23.73 40.22

Packaged Assy NA 68.76 35.50 46.50

Center of gravityTable 27 shows the center of gravity measurements for the 42U low-voltage cabinet. Table 28 shows thesame information for the 36U low-voltage cabinet.

The center of gravity of the assemblies is measured from the front mounting face of the vertical mountingrails, the top inside surface of the cabinet base, and the center of the cabinet (1.5 inches).


Table 27 Center of gravity measurements 42U low-voltage cabinet

Measurement Inches

Depth from mounting face of vertical mounting rails 16.56

Height from inside base 37.09

Distance from cabinet center (viewing front of cabinet) 0.46 (left of center line)

Table 28 Center of gravity measurements 36U low-voltage cabinet

Measurement Inches

Depth from mounting face of vertical mounting rails NA

Height from inside baseNA NA

Distance from cabinet center (viewing front of cabinet) NA

Tip stabilityThe system must pass tip stability testing for a 10 tip test and 250N side-force tip test perCAN/CSA-C22.2 No. 60950-00/3rd Edition, Safety of Information Technology Equipment.

Results of tip and tilt calculations show that the testing of this configuration is not necessary. Center ofgravity locations, within the 10 boundaries show no danger of tip. Force tip testing calculations indicatethat the rear force tip test need not be performed.

62 Low-voltage Japanese cabinets

Index

Symbols2C2D configuration

describing features, 22, 4636U rack, 1342U rack, 13

Ccontroller

defined, 16conventions

document, 9text symbols, 10

customer self repair, 11

Ddocument

conventions, 9prerequisites, 9

documentationproviding feedback, 11

Eenclosures, physical specifications, 53environmental specifications

drive enclosure, 53

FFC drive enclosures

describing features, 13FC loop switches

describing features, 14Fibre Channel drive enclosure, 13

Hhelp

obtaining, 10HP

technical support, 10HSV Controllers

defined, 16

Lloop topology, 14

Oopal rack, 13

Pphysical specifications

enclosures, 53power specifications

drive enclosure, 54prerequisites, 9

Rrack stability

warning, 10

SSFP, 15specifications

physical, 53power, 54

storage racks, 13, 13Subscriber's Choice, HP, 11symbols in text, 10

Ttechnical support

HP, 10service locator website, 11

text symbols, 10topology, 14transceivers, 15

Wwarning

rack stability, 10websites

customer self repair, 11HP , 11HP Subscriber's Choice for Business, 11


4x00 6x00 8x00 Enterprise Virtual Array Setup Guide

Documents

Transcript of 4x00 6x00 8x00 Enterprise Virtual Array Setup Guide