4fai Bts Pnp

Nokia Siemens Networks WCDMA RAN, Rel. RU20, Operating Documentation, Issue 04

Activating RAN1298 and RAN1299: BTS plug-and-play

DN0934041

Issue 01BApproval Date 2010-06-30

Confidential

2 DN0934041Issue 01B


Id:0900d80580779d0fConfidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2010. All rights reserved

f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.

Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.

Therefore, only trained and qualified personnel may install and maintain the system.

The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.

The same text in German:

Wichtiger Hinweis zur Produktsicherheit

In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.

Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.

Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.

Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.

DN0934041 Issue 01B

3



Table of contentsThis document has 25 pages.

1 Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Activating RAN1298: BTS auto connection . . . . . . . . . . . . . . . . . . . . . . . 8

3 Verifying RAN1298: BTS auto connection . . . . . . . . . . . . . . . . . . . . . . . 14

4 Deactivating RAN1298: BTS auto connection . . . . . . . . . . . . . . . . . . . . 16

5 Activating BTS Auto connection and Auto configuration through the NetAct17

5.1 About this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.1.1 NetAct compatibility and capacity information . . . . . . . . . . . . . . . . . . . . 175.2 Preconditions and requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175.2.1 Checking BTS Auto connection feature license. . . . . . . . . . . . . . . . . . . 185.2.2 Checking BTS Auto configuration feature license . . . . . . . . . . . . . . . . . 205.2.3 Checking the version of RNC software . . . . . . . . . . . . . . . . . . . . . . . . . 215.3 Enabling autotriggering of WBTS auto configuration (optional) . . . . . . . 225.4 Configuring e-mail notification (optional) . . . . . . . . . . . . . . . . . . . . . . . . 235.5 Auto Configuration Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255.6 Where to find more information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25




List of figuresFigure 1 RNC, WBTS, CA/CR settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Figure 2 The BTS object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 3 Auto Connection HW ID and Site ID parameters . . . . . . . . . . . . . . . . . . 15Figure 4 Upload dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Figure 5 BTS Auto Connection option under the RNC Options parameter . . . . . . 20Figure 6 Software Manager view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DN0934041 Issue 01B

5



List of tablesTable 1 licenses needed for BTS auto configuration. . . . . . . . . . . . . . . . . . . . . 18Table 2 licenses recommended for BTS auto configuration . . . . . . . . . . . . . . . 18

DN0934041 Issue 01B

7

Activating RAN1298 and RAN1299: BTS plug-and-play Summary of changes

Id:0900d805807a559dConfidential

1 Summary of changesChanges between issue 01A (09/12/2009) and 01B (30/06/2010)Modified chapter: Activating RAN1298: BTS auto connection

Changes between issues 01 and 01AEditorial changes have been made.

Issue 01This is the first issue of the document.



Id:0900d8058077851cConfidential

Activating RAN1298: BTS auto connection

2 Activating RAN1298: BTS auto connectionPurposeFollow the procedure below to activate RAN1298: BTS auto connection feature.

Before you startRestart of the RNC and the BTS is not required after activation of this feature.

This feature belongs to application software and is under license key management. Make sure you have a valid license (a file including the feature information) installed. To check if the RNC license is activated, use the W7I command. For more information on using the command, see W7 - Licence and Feature Handling.

Before a licensed feature can be activated, the license must be transferred to and installed in the RNC. For information on transferring the license to the RNC, see License management operations in RNC in WCDMA RAN license management.

You can install the license using NetAct or a local MML interface. If you install the license using NetAct, the feature covered by the license is automatically set to the ON state. For information on license management in NetAct, see Managing Licenses, License Manager Help, Licence Manager Technical Reference Guide, and Licence Manager problems in Troubleshooting System Management Problems in Nokia Siemens Networks NetAct documentation.

g BTS plug-and-play feature requires that RAN1299: BTS auto configuration feature license is activated in NetAct.

If you use the MMI, you must also set the feature state (ON/CONFIG/OFF). In new installations, the default state is OFF. For the specific instructions on the license instal-lation in the RNC, see W7L INSTALL OR UPDATE LICENCE in W7 - Licence and Feature Handling.

For more information on license management, see License management principles, and License management in WCDMA RAN.

To set the feature state, use the following command:

ZW7M:FEA=<feature code>:<feature state>

g The feature code for this feature is 1479.

Steps

1 Start the man-machine interface (MMI)

2 Use ZW7M:FEA=1479:ON; MML command to activate the feature

Expected outcomeRAN1298: BTS auto connection feature has been activated.

Use W7I:FEA,FULL:FEA=1479; MML command to verify if the feature has been acti-vated. If the feature has been activated FEATURE STATE parameter value is set to ON< ZW7I:FEA,FULL:FEA=1479;

LOADING PROGRAM VERSION 1.20-0FEATURE INFORMATION:

DN0934041 Issue 01B

9

Activating RAN1298 and RAN1299: BTS plug-and-play Activating RAN1298: BTS auto connection


----------------------------------------------FEATURE CODE:..............1479FEATURE NAME:..............RAN1298 BTS Auto ConnectionFEATURE STATE:.............ONCOMMAND EXECUTED

g DHCP server in RNC needs to be configured before BTS Auto-Connection can be started, see Configuring DHCP server on RNC in Configuring IP connection for RNC.

DHCP Server Settings in RNC - ExampleFigure 1 presents a simplified example of an RNC, WBTS and CA/CR server. The IP adresses in the figure correspond to the MML printouts in this chapter.

Figure 1 RNC, WBTS, CA/CR settings

OMU

WBTS

RNC

172.16.67.105

NPGEP-0/1

172.16.67.110 (IFFE0)

172.16.58.129 (VL968)

CA/CR

172.16.67.108

DHCP pool for VL968

172.16.58.138 -

172.16.58.142

ZUSI:OMU;

LOADING PROGRAM VERSION 6.17-1

WORKING STATES OF UNITS 2010-04-30

11:22:01

UNIT PHYS LOG STATE INFO

OMU-0 0000H 4002H SP-EX -

OMU-1 0001H 4002H WO-EX -

NUMBER OF UNITS DISPLAYED = 2

10 DN0934041Issue 01B




COMMAND EXECUTED

WORKING STATE AND RESTART HANDLING COMMAND

<US>

< ZUSI:NPGEP;


WORKING STATES OF UNITS 2010-04-30

11:22:06

UNIT PHYS LOG STATE INFO

NPGEP-0 0025H 48DFH WO-EX -

NPGEP-1 0041H 48DFH SP-EX -

NUMBER OF UNITS DISPLAYED = 2

COMMAND EXECUTED

WORKING STATE AND RESTART HANDLING COMMAND <US_>

ZQRI:OMU,1;


RNC IPA2800 2010-04-30 11:22:18

IINTERROGATING NETWORK NTERFACE DATA

IIF ADM FRAG IF ADDR

UNIT NAME STATE MTU SUPP PRIO TYPE TYPE IP ADDR

------------------- ------------- ------------ ------------------- ---------------- ---------- -----------

OMU-1 EL0 UP 1500 Y - - L 172.16.67.105/28

COMMAND EXECUTED

TCP/IP STACK DATA HANDLING COMMAND <QR_>

<

DN0934041 Issue 01B

11



MAIN LEVEL COMMAND <___>

<QRI:NPGEP,0;


RNC IPA2800 2010-04-30 11:22:43

INTERROGATING NETWORK INTERFACE DATA

IF ADM FRAG IF ADDR

UNIT NAME STATE MTU SUPP PRIO

TYPE TYPE IP ADDRESS

-------------- -------------

------------ ------------------- --------- ------------ ----------------------------

NPGEP-0 IFAI0 UP 1500 Y U L 172.16.70.178/32

IFAI1 UP 1500 Y U L 172.16.70.194/32

IFFE0 UP 1500 Y L 172.16.67.110/28

IFGE0 UP 1500 Y L

IFGE1 UP 1500 Y L

LO0 UP 1500 Y L 172.16.70.178/30

VL968 UP 1500 Y L 172.16.58.129/28

COMMAND EXECUTED

TCP/IP STACK DATA HANDLING COMMAND <QR_>

<ZQKB:OMU,1;


RNC IPA2800 2010-04-30

11:23:24

INTERROGATING STATIC ROUTES

ROUTE

UNIT DESTINATION GATEWAY ADDRESS TYPE Preference NBR

12 DN0934041Issue 01B




----------------------------- ----------------------- ------------------- ------------- -------- --------

OMU-1 DEFAULT ROUTE

172.16.67.97 LOG 0 1

OMU-1 172.16.71.0/24 172.16.67.110 LOG 0 85

OMU-1 172.16.58.128/27 172.16.67.110 LOG 0 115

COMMAND EXECUTED

IP ROUTING DATA HANDLING COMMAND <QK_>

<

MAIN LEVEL COMMAND <___>

<

? ..... DISPLAY MENU

O ..... MANAGE DHCP SERVER STATUS

C: ..... CONFIGURE IP ADDRESS POOL

Q: ..... INTERROGATE IP ADDRESS POOL

D: ..... DELETE IP ADDRESS POOL

K: ..... MANAGE IP ADDRESS RANGE LIST

B: ..... MANAGE POOL BINDING INFORMATION

L: ..... INTERROGATE POOL BINDING INFORMATION

N: ..... CONFIGURE DHCP SERVER OPTIONS

I: ..... INTERROGATE DHCP SERVER OPTIONS

T: ..... MANAGE DHCP SERVER CLIENT STATUS

A: ..... INTERROGATE DHCP CLIENT DYNAMIC INFORMATION

S: ..... MANAGE DHCP SERVER LOGS

G: ..... DISPLAY LOG INFORMATION

Z: ..... RETURN TO MAIN LEVEL

DHCP SERVER DATA HANDL COMMAND <Q9_>

<Q;

INTERROGATE POOL INFORMATION

POOL ID POOL NAME SUBNET/MASK GATEWAY RANGE

DN0934041 Issue 01B

13



-------------------- ------------------ ----------------------- ------------------- --------------

1 BTSDHCP 172.16.58.128/28 172.16.58.129 172.16.58.138

>172.16.58.142

Q9L:;

INTERROGATE POOL BINDING INFORMATION

POOL ID POOL NAME UNIT IF NAME

-------------------- ------------------ ----------------------- ------------------- --------------

1 BTSDHCP NPGEP-0 VL968

COMMAND EXECUTED

Q9I:;


INQUIRE DHCP VENDOR OPTION IP PARAMETER INFORMATION:

CA/CMP CERTIFICATE

CERTIFICATE

O&M MEDIATOR CA/CMP SERVER SERVER PORT REPOSITORY

REPOSITORY

----------------------- ------------------------- ----------------- ------------------- ---------------------

172.16.67.105 172.16.67.108 8080 172.16.67.108 389

COMMAND EXECUTED

14 DN0934041Issue 01B


Id:0900d805807138b5Confidential

Verifying RAN1298: BTS auto connection

3 Verifying RAN1298: BTS auto connectionPurposeFollow the procedure below to verify that the activation of the RAN1298: BTS auto con-nection feature has been successful.

Steps

1 Open the RNC RNW object browser from application launcher

2 Open WBTS object, then check if Auto Connection HW ID (Auto Connection Hardware ID) or Site ID (Auto Connection Site ID) parameter fields are active. Double click on RNC object if WBTS objects cannot be seen.

Figure 2 The BTS object

DN0934041 Issue 01B

15

Activating RAN1298 and RAN1299: BTS plug-and-play Verifying RAN1298: BTS auto connection


Figure 3 Auto Connection HW ID and Site ID parameters

16 DN0934041Issue 01B



Deactivating RAN1298: BTS auto connection

4 Deactivating RAN1298: BTS auto connectionPurposeFollow the procedure below to deactivate RAN1298: BTS auto connection feature.

Steps

1 Start the man-machine interface (MMI)

2 Use ZW7M:FEA=1479:OFF; MML command to deactivate the feature

Expected outcomeRAN1298: BTS auto connection feature has been deactivated

Use ZW7I:FEA,FULL:FEA=1479; MML command to verify if the feature has been deactivated. If the feature has been deactivated FEATURE STATE parameter value is set to OFF< W7I:FEA,FULL:FEA=1479;

LOADING PROGRAM VERSION 1.20-0FEATURE INFORMATION:----------------------------------------------FEATURE CODE:..............1479FEATURE NAME:..............RAN1298 BTS Auto ConnectionFEATURE STATE:.............OFFCOMMAND EXECUTED

DN0934041 Issue 01B

17

Activating RAN1298 and RAN1299: BTS plug-and-play Activating BTS Auto connection and Auto configurationthrough the NetAct


5 Activating BTS Auto connection and Auto configuration through the NetAct

5.1 About this chapterThis section provides you information on how to check if all requirements needed for BTS auto connection and BTS auto configuration are met on the NetAct site.

For instructions on manual connection and manual activation of WBTS, see Plan-based roll-out method in Rolling out the WCDMA RAN.

For instructions on using BTS Auto connection and BTS Auto configuration features, see Rolling out the WCDMA RAN document.

This section is intended for operators and administrators of radio networks, and anyone requiring information about the activation procedure of the BTS Auto connection and BTS Auto configuration features.

5.1.1 NetAct compatibility and capacity informationFor information on NetAct system and capacity, and the compatibility between NetAct and network element releases, see the NetAct compatibility and capacity information document.

5.2 Preconditions and requirementsg Auto connection and Auto configuration features are supported only by FlexiBTS.

FlexiBTS version WN6.0 and onwards support these features.

The following NetAct tools are used in the operations:

• CM Editor • CM Operations Manager (Workflow Engine, Plan Actual Compare) • Software Manager

Before starting to use BTS Auto connection and BTS Auto configuration features, the following preconditions have to be met:

• BTS auto connection license is active in the RNC under which you want to auto connect the BTS.

• BTS auto configuration license is active in NetAct. • RNC software version is updated to RN5.0 level. • Autotriggering of WBTS auto configuration is enabled (optional). • E-mail notification properties are configured (optional).

g It is up to Operator to decide whether he wants to have E-mail notification or not. • Auto Configuration Report is available. • Additionally, the following licenses are active in the NetAct:

18 DN0934041Issue 01B



Activating BTS Auto connection and Auto configuration through the NetAct

• The following licenses are recommended to be active in the NetAct:

Chapters below give instructions on how to check these preconditions.

5.2.1 Checking BTS Auto connection feature licenseThis procedure describes how to check if the license for Auto connection feature is active in RNC. Before checking that the needed option is available, upload the latest option information from the RNC.

To check BTS auto connection options1. Open CM Operations Manager.2. Select Upload → New Upload.

Expected outcomeThe Upload dialog opens.

3. Select all the RNC(s) which you want to upload.

Sales item license name

WBTS Autoconfiguration for 3G CM_MGMT_3G_AUTOCONFIGURATION

Remote Site Configuration Manage-ment for 3G

CM_MGMT_3G_SITE_CONFIGURATION

FlexiTRS Parameter Management CM_FLEXI_TRS

XML interface for radio access planning data

XML_RA_PLAN_IF

CM Editor for RAN CM_EDITOR_RAN

CM Operations Manager for RAN CM_OPMGR_RAN

CM Workflow Engine CM_WORKFLOW

Table 1 licenses needed for BTS auto configuration.

Sales item license name

RNC ATM/IP Management CM_RNC_ATM_IP

Direct activation for RNC CM_RNC_DIRECT_ACTIVATION

Plan Actual Compare 3G PLAN_ACTUAL_COMPARE_3G

Table 2 licenses recommended for BTS auto configuration

DN0934041 Issue 01B

19



Figure 4 Upload dialog4. Click Start to start the upload operation.

For more information, see CM Operations Manager Help.5. After upload is done, open CM Editor.6. In the Actual Configuration node select the RNC under which you want to perform

the auto connection and auto configuration. 7. Check if the BTS Auto Connection option is visible in the RNC Options param-

eter.

20 DN0934041Issue 01B




Figure 5 BTS Auto Connection option under the RNC Options parameter

g If the BTS Auto Connection option is visible under the RNC Options parameter, the auto connection service is activated in the RNC.

If the auto connection option is not visible, you need to purchase the auto connection option from Nokia Siemens Networks.

5.2.2 Checking BTS Auto configuration feature licenseThis chapter provides instructions on how to check the status of BTS Auto configuration feature license.

g Auto configuration feature is supported only by FlexiBTS.

For further information about BTS Auto configuration feature, see Configuring WCDMA FlexiBTS Using Auto Connection and Auto Configuration document.

g You cannot rely on that if auto connection license exists (in RNC) then also auto configuration license is active in Configurator.

You have to check the auto configuration license status separately.

To check BTS Auto configuration feature license1. Login to Connectivity Server as omc user.2. Open lmdlicmx.dat license file by running the following command:

less /etc/opt/nokia/oss/common/conf/lmdlicmx.datThe lmdlicmx.dat license file lists all active licenses in the system.

DN0934041 Issue 01B

21



3. Check if the licenses needed for BTS auto configuration exist in the lmdlicmx.dat license file.g Example of the license entry in the lmdlicmx.dat license file:

# RAC OSSWxx51 TBD / Configuring and Optimising / Radio Access Configurator / CM Operations Manager RACPMG FEATURE CM_MGMT_3G_AUTOCONFIGURATION lmdntcmx 50.000 01-jan-0 0 4D2BC06FC8067A717740 \ HOSTID=ANY ck=17license entry has the following structure:<sales item> / <functionality area> / <system component> / <feature name>

4. Close the lmdlicmx.dat license file, by putting the following command:q

5.2.3 Checking the version of RNC softwareIn order to support Auto connection and Auto configuration features, the RNC(s) under which you want to perform BTS auto connection and BTS auto configuration should have the RN5.0 software package installed.

This section describes how to check that the RNC is updated to RN5.0 level.

Checking the status of RNC software can be done by using Software Manager or CM Editor.

g It is recommended to use Software Manager to check software version of more than one RNC at the same time.

To check the RNC software (with NetAct Software Manager)1. Open NetAct Software Manager.2. Select RNC as the NE type from the Show: drop-down list.3. Select the appropriate parent network from the Parent tab.

Expected outcomeThe network elements under the selected parent are displayed in the Network elements table on the right-hand side.

4. From the Network elements table select the network elements in which the Auto configuration feature will be activated.

5. Open the New Task tab at the bottom of the pane.The selected network elements are shown in the Selected network elements table on the right-hand side.

6. Select upload from the Task type drop-down list.7. Click the Start Task button to continue.

Expected outcomeThe software information upload starts. You can follow the progress of the upload operation in the Tasks tab.

8. Go to the Network SW Status tab.9. From the Network elements table, check if all selected RNC(s) have the required

software package installed.

22 DN0934041Issue 01B




Figure 6 Software Manager view

If the required software packages have not been installed on all necessary RNCs, you need to download and activate appropriate software packages. For instructions, see Software Manager Help.

To check the RNC software (with CM Editor)1. Open CM Editor.2. In the Actual Configuration node move your mouse cursor on top of the RNC under

which you want to perform the auto connection and auto configuration. 3. Wait until hint window is shown. Hint window shows the RNC software version.

5.3 Enabling autotriggering of WBTS auto configuration (optional)This section gives instructions on activating the autotriggering of workflow operations in order to commission WBTS without operator user attention.

g This functionality is optional. You can perform this operation manually by using BTS configuration trigger workflow in CM Operations Manager’s Workflow Engine. For more information, see chapter Triggering a BTS auto configuration polling mecha-nism in Configuring WCDMA FlexiBTS Using Auto Connection and Auto Configura-tion document.

To enable autotriggering of WBTS auto configuration1. Login to Connectivity Server as omc user.2. Open crontab file by running the following command:

DN0934041 Issue 01B

23



crontab -e

3. Add new line at the end of the crontab file:0,15,45 * * * * /bin/bash -lc "racclimx.sh -v -opsFile /etc/opt/nokia/oss/rac-5.0/conf/opdefs/ops/operations/bts_auto_conf_trigger.xml -op 'BTS auto configuration trigger'"

4. Save and exit crontab file, by running the following command::qw!

Expected outcomecrontab: installing new crontab

5.4 Configuring e-mail notification (optional)This section describes how to configure e-mail notification functionality. After performing the following procedure, the NetAct system will be able to notify the user about the status of BTS auto connection and auto configuration by sending notification e-mails.

This procedure has two main steps:

• Configuration of SMTP (Simple Mail Transfer Protocol) server in LDAP • Configuration of e-mail notification recipients list

To configure the SMTP (Simple Mail Transfer Protocol) server in LDAP1. Login to DS-1 server as root user.2. Add the FQDN of SMTP server in /etc/ClusterConfig.xml file.

<SMTP Setup="yes" FQDN="mailserver.rc502040.netact.noklab.net"/>

g In the above tag, the attribute value mailserver.rc502040.netact.noklab.net should be replaced with adequate domain name of the mail server.

3. Configure the SMTP server entry in LDAP either for adding or deleting using the fol-lowing steps:To add an entry to LDAP, perform the following steps: • In the /tmp directory, create ADD_mail.xml file with the following content:

g In the above step, the ADD_mail.xml file is only an example. You can create an xml file with any name.

<?xml version="1.0" encoding="UTF-8" standalone="yes"?><LDAPContent><LDAPEntry Type="Modify" DN="cn=cluster,ou=config,ou=region-502040,ou=regions,ou=netact,dc=noklab,dc=net" Overwrite="No"><Attr Name="ossSmtpFQDN" Changetype="add"Value="mailserver.rc502040.netact.noklab.net"/></LDAPEntry>

24 DN0934041Issue 01B




</LDAPContent>

• Add the following entry to LDAP using the xml file created:/opt/nokia/oss/bin/XML2LDAP.pl --install --file /tmp/ADD_mail.xml

To delete an entry from LDAP, perform the following steps: • In /tmp directory, create DEL_mail.xml with the following content:

g In the above step, the DEL_mail.xml file is only an example. You can create an xml file with any name.

<?xml version="1.0" encoding="UTF-8" standalone="yes"?><LDAPContent><LDAPEntry Type="Modify" DN="cn=cluster,ou=config,ou=region-502040,ou=regions,ou=netact,dc=noklab,dc=net" Overwrite="No"><Attr Name="ossSmtpFQDN" Changetype="delete"Value="mailserver.rc502040.netact.noklab.net"/></LDAPEntry></LDAPContent>

• Remove the following entry from LDAP using the created xml file:/opt/nokia/oss/bin/XML2LDAP.pl --install --file /tmp/DEL_mail.xml

4. Check the SMTP entry in LDAP by executing the following command:ldapacmx.pl -directQuery "cn=cluster" |grep ossSmtpFQDNThe following is the output:ossSmtpFQDN=mailserver.rc502040.netact.noklab.net

To create an e-mail notification sending list1. Login to Data Storage Server as omc user.2. Open the

/etc/opt/nokia/oss/custom/conf/autoconfiguration_recipients file by running the following command:vim /etc/opt/nokia/oss/custom/conf/autoconfiguration_recipients

g If there is no file, create a new one by running the following command:touch /etc/opt/nokia/oss/custom/conf/autoconfiguration_recipients

3. Add appropriate e-mail address(es) to which you want to send the e-mail notifica-tion. g Add one e-mail address per line.

4. Save and exit the autoconfiguration_recipients file by running the following command:

DN0934041 Issue 01B

25



:qw!

5.5 Auto Configuration ReportAuto Configuration Report is a web-based application which allows you to view status of auto configuration of the WBTS(s) in the network.

The configuration of Auto Configuration Report user account does not require any specific steps on the NetAct site. The only thing that need to be done is the first time login to the application.

To open Auto Configuration Report1. In the web browser, enter the following URL:

http://<clustername>.netact.noklab.net/RAC_cmpser/reportwhere <clustername> stands for the host name that has been assigned to the LinAS server. If not known, contact your system administrator.

2. Fill in the Username and Password field.3. Click Login button to enter the Auto Configuration Report.

g Steps 2 and 3 are required only during the first use the application unless you use the logout function.

To exit Auto Configuration ReportTo exit the Auto Configuration Report use one of the following alternatives:a) Close the web browser.b) Click the logout button (to force login operation during the next Auto Configuration

Report opening) and close the web browser.

5.6 Where to find more informationWhen you perform the tasks described in this section, you may need to refer to other documents for further information. The document list given below contains useful docu-ments and a brief description of their contents.

Help documentsFor more information on using Software Manager, see Software Manager Help.

For more information on using CM Operation Manager, see CM Operations Manager Help.

For more information on using license Manager, see license Manager Help.

4fai Bts Pnp

Documents

Transcript of 4fai Bts Pnp