485PB-NR, 485PB-MS-NR, 485PB-SMC-NR 232PB ... -...
Transcript of 485PB-NR, 485PB-MS-NR, 485PB-SMC-NR 232PB ... -...
485PB-NR, 485PB-MS-NR, 485PB-SMC-NR232PB-NR, 232PB-MS-NR, 232PB-SMC-NRNLMPB-NRNachrüstung der KommunikationsschnittstelleRetrofitting the Communication Interfaces
Kurzanleitung / Short Description Version 1.4 PB-NR-IXX073014TBX-485/232/NLM-NR
Sunny Boy SB / SWR, Sunny Mini Central, Windy BoyNachrüstung der Kommunikationsschnittstellen
Autor: Y. Siebert Dok.-Nr.: PB-NR-IXX073014
Version: 1.4 Material-Nr.: TBX-485/232/NLM-NR
BeschreibungDie SMA Wechselrichter können mit verschiedenen Schnittstellen für die Kommunika-tion ausgestattet werden. Diese Kurzanleitung beschreibt die Nachrüstung eines Sun-ny Boy, Sunny Mini Central oder Windy Boy mit einem Piggy-Back für dieKommunikation. Dabei kann es sich um die folgenden Piggy-Backs handeln:
• RS485 (485PB-NR, 485PB-MS-NR, 485PB-SMC-NR)• RS232 (232PB-NR, 232PB-MS-NR, 232PB-SMC-NR)• Netzleitungskommunikation (NLMPB-NR)
Die hier beschriebenen Piggy-Backs können in folgenden Wechselrichter eingebautwerden:
Achtung: Alle Arbeiten an einem Wechselrichter, insbesondere dasÖffnen des Wechselrichters, dürfen nur von einer ausgebildeteElektrofachkraft durchgeführt werden! Beachten Sie bei der Instal-lation eines Piggy-Backs in einem Wechselrichter alle Schutzvor-schriften in der Installationsanleitung des Wechselrichters.
Achtung: Arbeiten am geöffneten Wechselrichter dürfen nur durch-geführt werden, wenn der Wechselrichter von der Versorgungs-spannung getrennt ist. Öffnen Sie den Wechselrichter wie in derInstallationsanleitung beschrieben.
Achtung: Beachten Sie bei den Arbeiten innerhalb des Wechselrich-ters immer die ESD Schutzvorschriften! Im Wechselrichter befindensich Komponenten, die durch statische Entladung irreparabel be-schädigt werden können. Sorgen Sie für eine leitende Verbindungzwischen Ihrem Körper und dem geerdeten Gehäuse des Wechsel-richters.
Hinweis: Bei einem Sunny Boy Typ "SWR" müssen Sie zunächst die Widerstän-de von der Betriebsführungsplatine entfernen, wenn Sie Ihr Gerät für dieRS232 oder RS485 Kommunikation mit einem PC oder einem Kommunikations-gerät einrichten wollen. Nähere Information zu der Entfernung der Widerstän-de finden Sie in dieser Anleitung.
Kurzanleitung PB-NR-IXX073014 Seite 3
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
• Sunny Boy vom Typ "SB" • Sunny Boy vom Typ "SWR" • Sunny Mini Central vom Typ „SMC“• Windy Boy vom Typ „WB“
Typenschild Sunny Boy Typ „SB“
Typenschild Sunny Boy Typ „SWR“
Kurzanleitung PB-NR-IXX073014 Seite 4
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Nachrüstung RS232RS232 bei einem Sunny Boy Typ "SB", Sunny Mini Central und Windy Boy
PE L N
A
S2
AB B
S1
��������� ����
����������
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
L N PE
A
S2
AB B
S1
A
S2
AB B
S1
RS232 Piggy-Back
Klemmleiste zum Anschluss des RS232 Kabels
Jumper dürfen bei RS232 Kommunikation
nicht gesteckt sein.
Kurzanleitung PB-NR-IXX073014 Seite 5
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
RS232 bei einem Sunny Boy Typ "SWR"
Verkabelung eines Wechselrichters über RS232 an einen PC
Verkabelung eines Wechselrichters über RS232 an einen Sunny Boy Control
RS232 Piggy-Back
Widerstände mit einem schwar-zen Ring bei RS232 entfernen.
Die Widerstände können braun oder blau sein.
Klemmleiste zum Anschluss des RS232 Kabels
Jumper dürfen bei RS232 Kommunikation nicht
gesteckt sein.
3
5
23
5
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
SWR 3000
GND
TXDRXD
PC mit Sunny Data Control
3
5
23
5
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
SWR 3000
GND
TXDRXD
Sunny Boy Control mit RS232 Piggy-Back auf
COM1
Kurzanleitung PB-NR-IXX073014 Seite 6
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Kürzen Sie den beiliegenden Silikonschlauch auf die benötigte Länge (von der PG-Verschraubung bis zur Schraubklemme am Piggy-Back).
Führen Sie die Adern der Kommunikationsleitung durch den Silikonschlauch!
Achtung: Um eine Personengefährdung bei einem Fehler im Gerätzu vermeiden, verwenden Sie bei der Montage eines RS232 oderRS485 Piggy-Backs den mitgelieferten Silikonschlauch.
+
+ + +
++ -
---
- -
EN
S1
EN
S2
S15
S13
S11
S9
S7
S5
200V
150V
ABC
Der Silikonschlauch muss die Datenleitung innerhalb des
Gehäuses vollständig umhüllen
Kurzanleitung PB-NR-IXX073014 Seite 7
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Nachrüstung RS485RS485 bei einem Sunny Boy Typ "SB", Sunny Mini Central und Windy Boy
PE L N
A
S2
AB B
S1
��������� ����
����������
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
L N PE
A
S2
AB B
S1
A
S2
AB B
S1
RS485 Piggy-Back
Klemmleiste zum Anschluss des RS485 Kabels
Die Funktion der Jumper ist auf Seite 10 beschrieben.
Kurzanleitung PB-NR-IXX073014 Seite 8
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
RS485 bei einem Sunny Boy Typ "SWR"RS485 Piggy-Back
Widerstände mit einem schwar-zen Ring bei RS485 entfernen.
Die Widerstände können braun oder blau sein.
Klemmleiste zum Anschluss des RS485 Kabels
Die Funktion der Jumper ist auf der nächsten Seite
beschrieben.
Kurzanleitung PB-NR-IXX073014 Seite 9
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Jumper Bedeutung Anmerkung
A 120 Ohm Abschluss-widerstand zwischen Klemme 2 (Data+) und Klemme 7 (Data-).
Am letzten Wechselrichter am RS485 Bus wird der 120 Ohm Abschlusswiderstand durch Jumper A oder einen 120 Ohm Wi-derstand zwischen Klemme 2 und 7 gewähr-leistet.Die Installation des Abschlusswiderstandes bei einem Sunny Boy Control / Sunny Boy Control Plus ist in der technischen Beschrei-bung des Sunny Boy Control / Sunny Boy Control Plus beschrieben.
B und C 680 Ohm Widerstän-de zwischen Klemme 2 (Data+) zu +5V und Klemme 7 (Data-) zu GND zur Symmetrie-rung des Signals.
Die Symmetrierung ist nur einmal am RS485 Bus erforderlich und sollte, wenn möglich am Sunny Boy Control intern erfolgen. Beim Anschluss von einem oder mehreren Wech-selrichtern an einen PC mit Schnittstellen-wandler I-7520 ist die Symmetrierung bereits integriert.
Hinweis: Ein RS485 Bus muss an beiden Enden terminiert und einmal symme-triert werden. Jumper A nur im Wechselrichter montieren, wenn dieser an ei-nem der Enden des RS485 Busses ist. Die Jumper B und C nur einmal innerhalbdes RS485 Busses, und auch nur dann setzen, wenn das Signal nicht anderwei-tig symmetriert werden kann. Beim Schnittstellenwandler I-7520 ist der Termi-nierungs- und der Symmetrierungswiderstand bereits integriert.
Hinweis: SMA empfiehlt als Schnittstellenwandler für die Kommunikation mitSMA Wechselrichtern den I-7520. Einzelheiten zu diesem Schnittstellenwand-ler finden Sie im Internet unter www.ICPDAS.com.
Kurzanleitung PB-NR-IXX073014 Seite 10
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Verkabelung eines Wechselrichters über RS485 an einen PC
GND
DATA+
max. 50Wechselrichter auf
RS485 Bus
Schirm mitGehäuseverbinden
Schirm mitGehäuseverbinden
10-polig. Klemmleiste aufdem Schnittstellenwandler
I-7520
D-SUB 9 Buchse amSchnittstellenwandler
I-7520
PC mitSunny Data Control
+10V ... 30V DC
SchnittstellenwandlerRS485 / RS232
I-7520
9
12
3
5
2
DATA-
10
7
5
7
5
2
2
3
5
2
LiYC
Y tw
iste
d pa
ir Ka
bel
LiYC
Y tw
iste
d pa
ir Ka
bel
externesNetzteil
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
Für den Abschlusswiderstandim letzten Wechselrichter am RS485 Busentweder Jumper A im Wechselrichter
stecken oder einen 120 OhmWiderstand zwischen Klemme 7 und
Klemme 2 installieren!
Kurzanleitung PB-NR-IXX073014 Seite 11
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Verkabelung eines Wechselrichters über RS485 an einen Sunny Boy Control
GND
DATA+
max. 50Wechselrichter auf
RS485 Bus
Schirm mitGehäuseverbinden
Schirm mitGehäuseverbinden
Abschlusswiderstand und Symmetrierungdes Signals,wie in der technischen
Beschreibung des Sunny Boy Controlbeschrieben, vornehmen!
7
5
2
LiYC
Y tw
iste
d pa
ir Ka
bel
LiYC
Y tw
iste
d pa
ir Ka
bel
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
Sunny Boy Controlmit RS485 Piggy-Back
auf COM1
5
3
8DATA-
5
7
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
Für den Abschlusswiderstandim letzten Wechselrichter am RS485 Busentweder Jumper A im Wechselrichter
stecken oder einen 120 OhmWiderstand zwischen Klemme 7 und
Klemme 2 installieren!
31
Kurzanleitung PB-NR-IXX073014 Seite 12
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Kürzen Sie den beiliegenden Silikonschlauch auf die benötigte Länge (von der PG-Verschraubung bis zur Schraubklemme am Piggy-Back).
Führen Sie die Adern der Kommunikationsleitung durch den Silikonschlauch!
Achtung: Um eine Personengefährdung bei fehlerhafter Installati-on zu vermeiden, verwenden Sie bei der Montage eines RS232oder RS485 Piggy-Backs den mitgelieferten Silikonschlauch.
+
+ + +
++ -
---
- -
EN
S1
EN
S2
S15
S13
S11
S9
S7
S5
200V
150V
ABC
Der Silikonschlauch muss die Datenleitung innerhalb des
Gehäuses vollständig umhüllen.
Kurzanleitung PB-NR-IXX073014 Seite 13
I
Nachrüstung Powerline (NLMPB-NR)In diesem Kapitel wird beschrieben, wie die Piggy-Backs der Variante NLMPB-NRnachgerüstet werden. Der Einbau der Piggy-Backs NLMPB-MS-NR und NLMPB-SMC-NR wird in separaten Dokumentationen beschrieben.
NLMPB bei einem Sunny Boy Typ "SB" und Windy Boy
Hinweis: In Sunny Boys Typ "SB" und Windy Boys sollten für Powerline Kom-munikation nur NLM Piggy-Backs Typ "F" oder höher eingebaut werden. BeiNLM Piggy-Backs Typ "A" bis "E" wenden Sie sich an die Sunny Boy Serviceline.
CBA
A
S2
AB B
S1
A
S2
AB B
S1
NLM Piggy-Back
Jumper dürfen bei Netz-leitungskommunikation
nicht gesteckt sein.
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
NLMPB bei einem Sunny Boy Typ "SWR"NLM Piggy-Back
Widerstände bei NLM NICHT entfernen.
Jumper dürfen bei Netz-leitungskommunikation
nicht gesteckt sein.
Kurzanleitung PB-NR-IXX073014 Seite 15
SMA Technologie AG Nachrüstung der Kommunikationsschnittstellen
Kurzanleitung PB-NR-IXX073014 Seite 16
Sunny Boy SB / SWR,Sunny Mini Central, Windy BoyRetrofitting the Communication Interfaces
Author: Y.Siebert Doc. No.: PB-NR-IXX073014
Version: 1.4 Material No.: TBX-485/232/NLM-NR
DescriptionThe SMA inverters can be equipped with various interfaces. This Short Descriptiondescribes the later installation of a Sunny Boy, Sunny Mini Central or Windy Boy witha Piggy-Back for communication. Following communication interfaces are available:
• RS485 (485PB-NR, 485PB-MS-NR, 485PB-SMC-NR)• RS232 (232PB-NR, 232PB-MS-NR, 232PB-SMC-NR)• Powerline (NLMPB-NR)
Caution: All maintenance works on an inverter, and especiallyopening of an inverter, are only to be conducted by a qualifiedelectrician! When installing a Piggy-Back in an inverter please noteall protective countermeasures of the Installation Guide of the in-verter.
Caution: Any work within the enclosure of the inverter is only allo-wed when the inverter is disconnected from the supply voltage.Open the inverter as described in the Installation Guide of the in-verter.
Caution: Pay attention to all applicable ESD protective counterme-asures! The inverter is assembled with components that are veryvulnerable to electrostatic discharge. Make sure that you are elec-trically connected to the enclosure of the inverter before you touchanything inside the enclosure.
Note: When upgrading Sunny Boys type "SWR" for RS232 or RS485 commu-nication please note: The resistors under the Piggy-Back must be removed forcorrect operation. More information for removing the resistors you find in thismanual
Short Description PB-NR-IXX073014 Page 17
SMA Technologie AG Retrofitting the Communication Interfaces
The Piggy-Backs described here can be installed in:
• Sunny Boy type "SB"• Sunny Boy type "SWR"• Sunny Mini Central type "SMC"• Windy Boy type "WB"
Sunny Boy type "SB"
Sunny Boy type "SWR"
Short Description PB-NR-IXX073014 Page 18
SMA Technologie AG Retrofitting the Communication Interfaces
Retrofitting RS232RS232 for a Sunny Boy type "SB", Sunny Mini Central and Windy Boy
PE L N
A
S2
AB B
S1
��������� ����
����������
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
L N PE
A
S2
AB B
S1
A
S2
AB B
S1
RS232 Piggy-Back
Terminal block for connection of the
RS232 cable
Jumper may not be mounted for RS232
communication
Short Description PB-NR-IXX073014 Page 19
SMA Technologie AG Retrofitting the Communication Interfaces
RS232 for a Sunny Boy type "SWR"
Wiring of an inverter with RS232 on a PC
Wiring of an inverter with RS232 on a Sunny Boy Control
RS232 Piggy-Back
Resistors with one black ring must be removed for RS232 communication. Resistors can
be brown or blue.
Jumper may not be mounted for RS232 communication
Terminal block for connec-tion of the RS232 cable
3
5
23
5
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
SWR 3000
GND
TXDRXD
PC with Sunny Data Control
3
5
23
5
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
SWR 3000
GND
TXDRXD
Sunny Boy Control with RS232 Piggy-Back on COM1
Short Description PB-NR-IXX073014 Page 20
SMA Technologie AG Retrofitting the Communication Interfaces
Shorten the provided silicone tube to the required length (from the PG screw connec-tion to the screw terminal of the Piggy-Back).
Lead the wires of the communication line through the silicone tube!
Caution: In order to avoid personal danger in case of a fault withinthe inverter definitely, use the provided silicone tube when instal-ling a RS232 or RS485 Piggy-Back.
+
+ + +
++ -
---
- -
EN
S1
EN
S2
S15
S13
S11
S9
S7
S5
200V
150V
ABC
The provided silicone tube has to enclose the data line inside the
enclosure completely.
Short Description PB-NR-IXX073014 Page 21
SMA Technologie AG Retrofitting the Communication Interfaces
Retrofitting RS485RS485 for a Sunny Boy type "SB", Sunny Mini Central an Windy Boy
PE L N
A
S2
AB B
S1
��������� ����
����������
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
CBA
A
S2
AB B
S1
A
S2
AB B
S1
L N PE
A
S2
AB B
S1
A
S2
AB B
S1
RS485 Piggy-Back
Terminal block for connection of the
RS485 cable
Function of the jumpers are described in the table on page 24
Short Description PB-NR-IXX073014 Page 22
SMA Technologie AG Retrofitting the Communication Interfaces
RS485 for a Sunny Boy type "SWR"RS485 Piggy-Back
Resistors with one black ring must be removed for RS485 communication. Resistors can
be brown or blue.
Function of the jumpers are described in the follwing table
Terminal block for connec-tion of the RS485 cable
Short Description PB-NR-IXX073014 Page 23
SMA Technologie AG Retrofitting the Communication Interfaces
Description of the jumpers A, B and C for RS485
Jumper Description Remarks
A 120 Ohm termination resistor between con-nector 2 (Data+) and connector 7 (Data-).
Mount jumper "A" on the last inverter on the RS485 bus in order to terminate the bus. A 120 Ohm connection between connector 2 and connector 7 has the same effect.The in-stallation of the termination resistor in the Sunny Boy Control / Sunny Boy Control Plus is described in the Technical Description of the Sunny Boy Control / Sunny Boy Control Plus.
B and C 680 Ohm resisors between connector 2 (Data+) to +5V and connector 7 (Data-) to GND for the pull-up/pull down resis-tors.
The pull-up/pull-down resistors for the RS485 bus are required only once on the bus. The I-7520 interface converter has both terminati-on and pull-up/pull-down resistors integrated internally - so jumper B and C do not have to be mounted. In case a different interface con-verter is used (which is not recommended) the pull-up/pull-down resistors can be activa-ted within the Sunny Boy by mounting the Jumpers B and C.
Note: A RS485 bus must be terminated on each end and must be symmetrizedonce. Jumper A in the Sunny Boy terminates the RS485 bus, so only mount thisjumper in the Sunny Boy on the end of the RS485 bus. Jumper B and JumperC symmetrize the RS485 bus - mount the jumpers only in one Sunny Boy on theRS485 bus and only if you are NOT using the I-7520 interface converter. (TheI-7520 has the termination and symmetrizing resistors integrated in the conver-ter.)
Note: SMA recommends the usage of a I-7520 interface converter for the con-nection of a RS485 bus directly to a COM port of a PC. Details about this con-verter are available under www.ICPDAS.com.
Short Description PB-NR-IXX073014 Page 24
SMA Technologie AG Retrofitting the Communication Interfaces
Wiring of an inverter with RS485 at a PC
GND
DATA+
max. 50inverter onRS485 bus
Connect shieldto case
Connect shieldto case
10-pin terminalon the interfaceconverter I-7520
D-SUB 9 socket onthe interface converter
I-7520
PC runningSunny Data Control
+10V ... 30V DC
Interface ConverterRS485 / RS232
I-7520
9
12
3
5
2
DATA-
10
7
5
7
5
2
2
3
5
2
iYC
Y tw
iste
d pa
ir ca
ble
iYC
Y tw
iste
d pa
ir ca
ble
ExternalPower Supply
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
The last inverter on theRS485 bus must be terminated.This is done by mounting jumper"A" on the system control board,
or by installing a 120 Ohm resistorbetween connector "2" and
connector "7".
Short Description PB-NR-IXX073014 Page 25
SMA Technologie AG Retrofitting the Communication Interfaces
Wiring of an inverter with RS485 at a Sunny Boy Control
GND
DATA+
max. 50inverter onRS485 bus
Connect shieldto case
Connect shieldto case
The termination resistor and thepull-up/pull-down resistors are activatedaccording to the technical documentation
of the Sunny Boy Control
7
5
2
LLiY
CY
twis
ted
pair
cabl
eLi
YCY
twis
ted
pair
cabl
e
BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
Sunny Boy Controlwith RS485 Piggy-Back
on COM1
5
3
8DATA-
5
7
2BetriebOperationErdschlussEarth FaultStörungFailure
Photovoltaik-Stringwechselrichter
Photovoltaic string inverter
The last inverter on theRS485 bus must be terminated.This is done by mounting jumper"A" on the system control board,
or by installing a 120 Ohm resistorbetween connector "2" and
connector "7".
31
Short Description PB-NR-IXX073014 Page 26
SMA Technologie AG Retrofitting the Communication Interfaces
Shorten the provided silicone tube to the required length (from the PG screw connec-tion to the screw terminal of the Piggy-Back).
Lead the wires of the communication line through the silicone tube!
Caution: In order to avoid personal danger in case of a fault withinthe inverter definitely, use the provided silicone tube when instal-ling a RS232 or RS485 Piggy-Back.
+
+ + +
++ -
---
- -
EN
S1
EN
S2
S15
S13
S11
S9
S7
S5
200V
150V
ABC
The provided silicone tube has to enclose the data line inside the
enclosure completely.
Short Description PB-NR-IXX073014 Page 27
SMA Technologie AG Retrofitting the Communication Interfaces
Retrofitting Powerline (NLMPB-NR)NLMPB for a Sunny Boy type "SB" and Windy Boy
Note: In Sunny Boys type "SB" and Windy Boys should be installed only NLMPiggy-Backs type "F" or higher for powerline communication. For NLM Piggy-Backs type "A" to "E" please call the Sunny Boy Serviceline.
CBA
A
S2
AB B
S1
A
S2
AB B
S1
Jumper may not be mounted for powerline
communication
NLM Piggy-Back
Short Description PB-NR-IXX073014 Page 28
SMA Technologie AG Retrofitting the Communication Interfaces
NLMPB for a Sunny Boy type "SWR"NLM Piggy-Back
Do NOT remove resistors for NLM communication
Jumper may not be mounted for NLM communication
Short Description PB-NR-IXX073014 Page 29
SMA Technologie AG
SS
SH3TFEFF
www.SMA.deales olar Technology
MA Technologie AGannoversche Strasse 1–54266 Niestetal, Germanyel. : +49 561 9522 4000ax: +49 561 9522 4040-mail: [email protected]: +800 SUNNYBOYreecall: +800 78669269
Seite 31 SB-SWR-RS-NR-12:SX3005 KurzanleitungInnovation in Systems Technology for the Success of Photovoltaics