470064 Rev01 - avfimg.com
Transcript of 470064 Rev01 - avfimg.com
60kg132lb
Max
VESA600 x 400mm
Max
AVF Group, Inc. 2775 Broadway, Cheektowaga, Buffalo, New York,14227 USA AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
Customer Helpline Online Support
1-800 667 0808(USA)
+44 (0) 333 320 0463(UK)
www.avfgroup.com/support
470064 Rev01
If you have any questions or needspare parts don’t worry, we’re happy to help.
Please read these instructions thoroughlybefore installation.
You will needRequired
Optional
Stud Finder
Wood
Masonry
Ø3mm (1/8”)
Ø7mm (1/4”)
Ø5.5mm (7/32”)
Masonry
Parts Included
K1x4
K2x4
K3x4
K4x4
K5x4
K6x4
K7x4
K8x4
K9x4
K10
x4
L1x6
L2x4
M1x12
M2x4
45mm
25mm
16mm
M4’s M5 M6’s M8’s
TV Screws, Reducers and Spacers
You will only need one set of TV Screws
A
B
C
D
F
E
Gx4
M5
Ix13
M5
Jx2
M5
16m
m
Hx6
Nx1
Ox1
Px1
Qx1
Rx1
3 Easy Steps
1 2 3
Attach the mountto your TV Build the column Hang and secure
1.1 Measure your VESA fixings and select TV Screws
75 - 600mma
b
75 - 400mm
This product fits fixing holes up to 600 x 400mm (MAX).
Determine which diameter TV Screwsfit your TV and put them to one side.
M4, M5, M6 or M8We will select the correct length later.
1.2 Prepare the TV Mounting Plate
H
Option 1For TV fixing holes over 200 x 200mm.
M5
16m
m
Hx4
x4
Loosen the Thumb Screws and adjust the VESA Adaptors to fit the holes on the back of your TV. You can use any hole on the adaptors. The TV Mounting Plate must be level and vertically centred on the back of your TV.
Top
200mm
100mm
75mm
75mm
100mm
200mm
F
M5
16m
m
Hx4
Top
Option 2For TV Fixing Holes 200 x 200mm or less.
If using Option 2 you need to remove the four VESA Adaptors. Keep the adaptors and fixings in a safe place in case they are needed in the future.
F
K1 - K10
L2
K
1 - K
4
K5 -
K7
K8 -
K10
L1
M2
M1
TV
TV TV TV
1.3 Fitting the TV Mounting Plate
You may need to use Spacers M1 or M2 if the screws are too long or the back of your TV is not flat.
If required
Do
you
need
L1
or L
2?
Top
After completing this step, you will have lots of TV screws left over.
Keep them in a safe place in case you require them in future.
Select the correct length TV screw.
x4
Make sure the TV Mounting Plate is still level and vertically centered on the back of your TV. Tighten the Thumb Screws.
2.1 Assemble the Column
M5
Ix11
B
C
I
D
I
A
I
Rx1
2.2 Fitting the Anti-tip Wall Anchor (Optional)
The anti-tip wall anchor is optional and provided for extra peace of mind.
Position your column against the wall where you want your TV. The rear edge of the column must be vertical and parallel to the wall. Mark the drill point through the top hole as shown.
Nx1
Ox1
Px1
Qx1
3mm (1/8")
Wood Stud
45mm (1-3/4")
5.5mm (7/32")
Solid Wall
7mm (11/40")
40mm (1-9/16")Min Gap
Plasterboard
Dot and Dab7mm (11/40")
45mm (1-3/4")
40mm (1-9/16")Max Gap
If the gap is greater than 40mm use the plasterboard fixing method
N O
ONP
ONQ
ONQ
The rear vertical edge must be parallel to the wall.
The horizontal face must be parallel to the floor
2.3 Fitting the TV Bracket
There are three height options for mounting the TV bracket.Choose the option that best allows you to mount the TV atyour preferred height.
B
A
Option 1Max Height
Option 2Mid Height
Option 3Min Height
To work out the height of your TV from the floor (B)use the following calculations:Option 1 1219mm (48”) - A = BOption 2 1151mm (45 5/16”) - A = BOption 3 1083mm (42 5/8”) - A = B
Distance A is measured from the bottom of the
TV Mounting Plate to thebottom of the TV.
M5
Ix2
M5
Jx2
M5
16m
m
Hx2
L1x2
I
L1J
H
E
3.1 Cable Management
ClipLocation
Slot
G
G
G
G
3.2a Position the Column
Position your column against the wall where you want your TV.
The rear vertical edge must be parallel to the wall.
The horizontal face mustbe parallel to the floor
Attaching to Optional Anti-tip Wall Anchor
You only need to follow this step if you have decided to use the optional anti-tip wall anchor.
3.3 Hanging the TV
3.2b
TV Leveling (Optional)
Tilt Adjustment (Optional)
If your TV needs leveling, only adjust the TV Leveling Screw on the low side of the TV. For example, if the left hand side of your TV is low, adjust the left hand TV Leveling Screw only, until your TV is level.
Adjust screws to achieve perfect tilt resistance if required. You can also lock the tilt if required.
x4
TV Leveling Screws