8/11/2019 4570 Error Code

1/3

4570 error code 9/29/2014

Code DescriptionC01 Main motor drive problemC04 Pedestal main drive problemC05 Duplex drive problem.

C11 Duplex exit motor.C12 Duplex end motor.C13 Upper cassette.C14 Lower cassette.C15 Pedestal upper cassette.C16 Pedestal middle cassette.C17 Pedestal lower cassette.C18 LCTC21 Scan problemC22 Lens problemC23 Mirror motorC26 Exposure lampC27 Scan motorC33 Set up failure

C35 Developer at transfer/separator adjustment. This might mean adeveloper leak or shorted corona.C41 Fuser thermistor or low temperature.C43 Fuser problem after warm-up.C44 Fuser problem after warm-up.C45 Fuser sub-thermistor open. User problems. Reset required. Turn offpower. Hold "0" & "8" keys while turning power on. Then press "8". Thenpress "9". Then press "print". You will read "3" in the display. Using the# keys, press "0" & "9" at the same time.E01 JamE02 Fuser jamE03 Jam at turn onE04 Front door opened during copy cycleE05 Registration jam

E08 Duplex unit jamE11 Duplex jamE12 Bypass jamE13 Upper cassette jamE14 2nd cassette jamE15 3rd cassette jamE16 4th cassette jamE17 4th cassette jamE19 CT jamE21 LCT jamE22-E25 Paper jams in copierE71 ADF feed jamE72 ADF transport jamE73 ADF exit jam

E74 RADF jamE75 ADF 2nd original jamE81-E85 Sorter jamE88 Jam after sortercf 60 drm nit spural stuckSC. 970 T.C Unit pr

Hold down the "Start" and "nine" buttons together while turning machine on.

Page 1

8/11/2019 4570 Error Code

2/3

4570 error code 9/29/2014

When machine goes beep you can let go. When it says "LIST PRINT" enter 102.When it says "input start code" enter 200 press start, When it says "inputend code" Enter 300. press start. Machine will print a list look down thelist for a 6 digit code , usually it will be one space to the left of wherethe other codes end. Its usually at or around code 263. On newer machines

it will be ****** ( 6 Asterisks) not a number. If number is displayed youcan enter that when accessing admin or if its ****** ( 6 Asterisks). Youwill have to go into 08 setting mode punch in the code number with the****** ( 6 Asterisks) next to it and enter a new 6 digit code that willbecome your new admin code. Hope that helps

If 1st time occur, u can just go to 08-400, reset the value to "0" thenrestart the machine.

When this code not cleat 08-400 then check these all thengs..1.Check the thermistors

(1) Check if the connectors are disconnected.(2) Check if the main and edge thermistors are in contact with the surfaceof the fuser roller properly?(3) Check if the harnesses of the main and edge thermistors are opencircuited.

2. Check the IH board and IH coil

(1) Check if the IH coil is broken.(2) Check if the connector of the IH coil is disconnected.(3) Check if the thermostat is blown.(4) Check if the connectors on the IH board are disconnected (AC input

connector and LGC I/F connectorCN455/456).(5) Check if the IH board or the switching power supply unit are abnormal. Replace the IH control board.

3. Check the LGC board(1) Check if the connectors CN316 are disconnected.(2) Check if the conductor pattern on the LGC board is short circuited or

Page 2

8/11/2019 4570 Error Code

3/3

4570 error code 9/29/2014

open circuited.(3) Replace the LGC board.

Page 3