454 ¾ Standard Brine Valve€¦ · The 454 3⁄ 4" Standard Brine ValVe retains its original...
Transcript of 454 ¾ Standard Brine Valve€¦ · The 454 3⁄ 4" Standard Brine ValVe retains its original...
The 454 3⁄4" Standard Brine ValVe retains its original features and proven design as an economical commercial brine valve. A new plastic alloy increases the strength and durability of this popular brine valve. 36" and 54" Float Rods are available.
Maximum Operating Pressure: 125 psig (862 kPa) Temperature Range: 40-110°F (4-43°C)
Please specify Float Rod length as listed below:
H7070-36 - 454 3⁄4" Standard Brine Valve(36" Rod)
H7070-54 - 454 3⁄4" Standard Brine Valve(54" Rod)
454 ¾" StandardBrine Valve
NOTE: The 454 ¾" Standard Brine Valve is designed for salt brine only. It will also fit inside a brine well that is 5" or larger.
0
2
4
6
0 1 2 3 4 5
Brine Draw Rate (gpm)
Va
cc
uu
m (
In.
of
Hg
)
Brine Draw Rate
Brine Draw Rate (gpm)
Vacc
uum
(In.
of H
g)
0
0.25
0.5
0.75
1
1.25
1.5
0 10 20 30 40 50 60
Pressure Drop (psig)
Ref
ill F
low
Rat
e (g
pm
)
Refill Flow Rate
Pressure Drop (psig)
Refil
l Flo
w R
ate
(gpm
)
H7070-14
3⁄4" Brine Tube(not supplied)
H7070-17
H7070-19
H7070-04
H7070-12HF(2 required)
H7070-13
H7070-09(6 required)
H7070-07
H7070-06
H7070-03T
H7070-16
H7070-08-36C or H7070-08-54C
H7070-05
H7070-04HF
H7070-18
H7070-03B
H7070-10 (6 required)
H7070-11 (6 required)
H7070-02
H7070-01
Order information:Order nUMBer deSCriPtiOn Order nUMBer deSCriPtiOn
H7070-01 Body H7070-09 SS Cover Screw
H7070-02 Plastic Plug - 3⁄4" H7070-10 SS Lock Washer
H7070-03T Seat Washer Top (Orange) H7070-11 SS Nut
H7070-03B Seat Washer Bottom (Clear) H7070-12HF Float Grommet
H7070-04 Refill Check Ball H7070-13 31⁄2" Bell Float PP
H7070-04HF High Flow Air Check Ball H7070-14 Float Rod Guide Asy
H7070-05 Ball Cage H7070-16 Upper Seat Retainer
H7070-06 O-rine Cover Seal H7070-17 Refill Chamber
H7070-07 Body Cover H7070-18 Lower Seat Retainer
H7070-08-36C Float Rod and Seat Cone Asy - 36" H7070-19 O-ring Refill Chamber Seal
H7070-08-54C Float Rod and Seat Cone Asy - 54"
1. Use Teflon tape only on threaded plastic pipe connections. Many liquid or paste pipe sealing products contain compounds that may cause plastics to crack with time.
2. PVC brine pipe is recommended for use with these valves as it is non-corrosive and threads easily.
3. After the proper float setting has been determined and the height set, place the float rod guide close to the float (but not as to hinder float operation), adjust to position the float directly above the brine valve and tighten securely.
4. Position the assembly securely in the brine well and check to see that there is no interference with the float operation.
454 ¾" Standard Brine Valve Installation Guide
nOte: this brine valve is intended for non-timed brine systems only and contains a refill check ball that limits the refill flow rate to 1.5 gpm.
Order nUMBer
deSCriPtiOn
H7070-03T Seat Washer Top (Orange)H7070-03B Seat Washer Bottom (Clear)H7070-06 O-ring Cover SealH7070-16 Upper Seat RetainerH7070-18 Lower Seat RetainerH7070-19 O-ring Refill Chamber Seal
Order no: H7070-34description: 454 Brine Valve Seal
replacement Kit
4462 DURAFORM LANE • WINDSOR, WISCONSIN 53598-9716 USAphone (608) 846-3010 fax (608) 846-2586 sales /customer service fax (800) 755-3010 H7070-25-01 • 11/18/2010www.clackcorp.com
474 Safety Brine Valve SystemOur 474 Safety Brine Valve System incorporates the 474 air check assembly to provide higher flow rates and greater flexibility than traditional brine delivery systems. Featuring a 1⁄2” riser pipe, our 474 Safety Brine Valve System is capable of providing brine draw and refill rates up to two gallons per minute when used with the optional 1⁄2” elbow. The 474 Safety Brine Valve System can be used as a safety back-up float or as the primary brine shut-off valve depending upon which float assembly you choose.
The 474 Safety Brine Valve System consists of threecomponents which must be ordered separately:
1. 474 Air Check Assembly The 474 air check assembly is available in three lengths; all
risers are 1⁄2” in diameter. Please specify 48”, 30.5”, or 22.5” length when ordering. See order numbers below.
2. 474 Safety Brine Valve The 474 safety brine valve includes a 3⁄8” elbow with polytube
insert. An optional 1⁄2” elbow with polytube insert may be ordered separately.
3. 474 Float Assembly There are two float lengths available. The 9.5” (overall length)
float assembly is designed to be used as a safety back-up float and is attached by a pin. The 32” (overall length) float assembly is designed to be used as the primary brine refill shut-off. It is easily adjusted with two grommets to fit your system (not shown).
• 1⁄2” riser pipe• Higher flow rates-refill and brine draw up to 11⁄2 gpm with 3⁄8” elbow and 2 gpm with optional 1⁄2” elbow• Fits both 31⁄2” and 4” brine wells• Can be used as a safety back-up float or primary brine shut-off• Easily adjustable float setting• Components are air tested to ensure proper performance
System Features:
All items are packaged 24/carton. Please order even carton quantities.
Order Information:ORDER
NUMBERDESCRIPTION
ORDER NUMBER
DESCRIPTION
H4500-48 474 Air Check 1⁄2” x 48” H4640-32 474 Float Assembly 32” w/2 Grommets
H4500-30.5 474 Air Check 1⁄2” x 30.5” H4650 Optional 1⁄2” Elbow & Polytube Insert
H4500-22.5 474 Air Check 1⁄2” x 22.5”H4600 474 Safety Brine Valve with 3⁄8” Elbow,
Polytube Insert & Float Assembly PinH4640-9.5 474 Float Assembly 9.5” (uses pin)
4462 DURAFORM LANE • WINDSOR, WISCONSIN 53598-9716 USAphone (608) 846-3010 fax (608) 846-2586 sales /customer service fax (800) 755-3010 Form No. 2396 • 12/3/2012www.clackcorp.com
Part No.: H4922 Updated 7/17/2007
4462 DURAFORM LANE • WINDSOR, WISCONSIN 53598-9716 USAphone (608) 846-3010 fax (608) 846-2586 sales/customer service fax (800) 755-3010
www.clackcorp.com
494 1" Commercial Brine Valve
U.S. Patent 7,243,669 and Foreign Patent Pending
V3149V3189
V3151
V3150
V3105
H4902
H4904
H4905-01
H4903
H4626
H4914
H4901
H4921
H4918-01
H4911
H4912
S2009 (4 required)
H4910
H4909
1.050" Riser H4952
H4955
H4954
H4951-01
H4624
H1036-33.5-01
JCP-PG-6-S0
H4920
ORDER NUMBERS:JCP-PG-6-S0 Nut 3/8 H1036-33.5-01 Float RodH4624 Float Rod PinH4626 Mounting Stud NutH4901 BodyH4902 CapH4903 O-Ring 226H4904 Disk Retaining BlockH4905-01 Check Disk AsyH4909 Cam Lever ArmH4910 Diaphragm Retaining BandH4911 Diaphragm SealH4912 Diaphragm RetainerH4914 Mounting StudH4918-01 Float Rod Guide AsyH4920 Float w/Lock 160 grams
Only one required
Installation Guide
1. If an external flow control is used, install on the inlet side of the brine valve.
2. Use Teflon tape only on threaded plastic connections. Many liquid or paste pipe sealing products contain compounds that may cause plastics to crack with time.
3. Position float. Hand tighten the nut.
4. Place the float rod guide close to the float (but not as to hinder float operation), adjust the guide to position the float so float rod pin operates freely and tighten securely.
5. Position the assembly securely in the brine well and check to see that there is no interferencewith thefloatoperation.
NOTE: When brine valve is used as a safety float for timed brine systems use refill rates up to 10 gpm. If used as a primary shut off, use refill rates up to 5 gpm. Repeated float closures at high refill rates can cause “water hammer,” which may damage the plumbing. This brine valve is designed for salt brine only and will fit inside a brine well that is 5” diameter or larger.
H4950-60
H4921 1” Socket Adapter H4950-60 Air Check with Riser 60" lengthH4951-01 Air Check BodyH4952 Air Check BasketH4954 Air Check SeatH4955 Air Check Ball H4956 Diaphragm Backup Ring S2009 Screw #6 X 5/8 SSV3105 O-Ring 215V3149 FTG 1 PVC Male NPT ElbowV3150 Fitting Split RingV3151 Fitting NutV3189 FTG 3/4&1 PVC Solvent Elbow
H4956