NODE B (Compact Smart 9312 )INSTALLATION & COMMISSIONING DOCUMENT

1. Refer Installation Guide (PDF File) for Installation. Snapshot of Node B with Cabling shown below .

HARDWARE INSTALLATION

RF and Power Cabling

PCM and Digital Cabling

DDF INSTALLATION

Pair/ Shield FunctionPCM 1 Receive 1PCM 2 Receive 2PCM 3 Receive 3PCM 4 Receive 4PCM 5 Receive 5PCM 6 Receive 6PCM 7 Receive 7PCM 8 Receive 8PCM 9 Transmit 1PCM 10 Transmit 2PCM 11 Transmit 3PCM 12 Transmit 4PCM 13 Transmit 5PCM 14 Transmit 6PCM 15 Transmit 7PCM 16 Transmit 8

2. Before Power ON of Node B , Ensure the following :-

(a) TRCU power cable is connected to 32 Amps MCB .

(b) D2U shelf Power cable is connected to 10 Amps MCB.

(c) Grounding of Node B is connected to IGB (refer to installation).

(d) Check the Voltage with multimeter at Node B end .

Data and software requirements:

a. Laptop with Windows XP with Internet explorer or mozilla

b. Cross LAN Cable

c. Alcatel Node-B commissioning doc

d. Java6 update5

e. Node-B software UNB06D00205

f. IP sheet

3. Connecting Laptop Locally to NODE B .

(a) Cross LAN Cable is Required

(b) Java should be Installed in the Laptop (set up file is attached)

(c) Change the IP Address of Laptop , As given Below

Connect to the TIL Port ( Port 1 of XCCM Card) .

Go to Internet Explorer and open the U

And following Window will appear

Put your name and Default Path where you want to save all Commissioning Reports .

And Following Board Screen will Appear

Upgrade the Node B Software to “ UNB06D00205”

4. Software Upgrade Procedure

Go to the Tools then Software upgrade then New software download , As shown below

Below Window will appear

Just show the Path where you have kept UNB06D00205 software and Select FILE0_UNDB06D00205 , As shown Below

And Click “Choose a Delievery File “:

“ This will take 15 minutes”

5. Activating New Software Release

Close the Connection ( Internet Explorer) and Reconnect . Once reconnected the new software will have username and password.

Username: nodeb

Password: nodeblnx

6. Procedure for Change of I&C Parameters (PCM , IP Address and IMA)

(a) Before making Changes , Save I&C Parameters

Save with name “OLD I&C site name”.

(b) Now Change I&C Parameters , only (PCM , IP Address and IMA)

PCM Modification:

Change PCM E1 Frame to Automatic Multiframe

IP Modification:

Reference:

Existence of a DHCP Server = NO

BTS IP address = 10.136.110.XX (get from excel sheet)

OMC-B IP address =

10.136.130.164

OMC-B Port = 6301

OMC-B VP identifier = 1

OMC-B VC identifier = 32

Subnetwork Mask =

255.255.255.0

BTS Port = 6301

IMA Modification:

Choose PCM&IMA Tab

Select IMA

SENDING CHANGES OF I&C PARAMETERS TO NODEB

Press Send to IBTS

Change in progress (20secs)

Success Message

SAVE CHANGES IN I&C PARAMETERS

Select Save I&C parameters

Change file name to “new_sitename.til”, press save

RESET NodeB (to activate changes in I&C parameters)

Reset in connected Mode

Confirm reset window

Note: NodeB will reset for approximately 5 mins.

Reconnect to BTS

7. MCA Backup File

Confirmation that MCA file created on CCM

Confirmation that MCA file copied on default directory

8. Global Inventory File

Go to Files Global Inventory File

Save

File will be saved on default path

END OF COMMISSIONING

IMPORTANT!!!!

After successful commissioning send a email to ALCATEL attaching the following files and information:

1. Site Name and Address.

2. Software Successfully upgraded to UNB06D00205 – (YES/ NO)

3. Global Inventory File

4. New I&C Parameter File

5. MCA File