405_1200_048_2 - Commissioning Manual - Rel 2_00
-
Upload
bartolome-carlos-orfila-nadal -
Category
Documents
-
view
12 -
download
1
description
Transcript of 405_1200_048_2 - Commissioning Manual - Rel 2_00
CE Terminals
Commissioning manual
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
ESA elettronica S.P.A. reserves the right to change the information contained in this document without notice. The information repre-sents no obligation on the part of the company.
All products referred to are covered by the appropriate trademark and/or copyright legislation.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
i
Quality Assurance
ESA elettronica’s quality control system has been certified by the CSQ, EQNet and ITQS (certification N° 9115.ESAE) as complying with UNI EN ISO 9001 standards.
These represent the most comprehensive set of standards within the interna-tional framework of ISO and cover every aspect of the life-cycle of the product (planning, development, production, installation and customer care).
All the products described in this manual comply with the following standards:electromagnetic compatibility (EMC):
• emissions EN 61000-6-4 (2001)• immunity EN 61000-6-2 (2001)
and thus are in line with:
Council Directives89/336/EEC 92/31/EEC 93/68/EEC
Tests carried out for CE-mark.
Immunity Disturbance characteristics Standard
To disturbances
Electrostatic discharge:ContactAir
EN61000-4-24kV8kV
Radio-FrequencyENV50140/ENV5014110 V/m
Rapid transitories:Power supplyI/O serial
EN61000-4-42 kV1 kV
Impulsive transitories Common and Differential mode
EN61000-4-5
To radiodisturbances
EmissionEN55011Level of radio disturbance B
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
iii
Contents
Foreword The manual ................................................................... F-1Its purpose .................................................................... F-1Conventions .................................................................. F-1
Introduction What is a CE Video Terminal ........................................ I-1
General information on electromagnetic compatibility (EMC)
Contents........................................................................ 1-1Laying cables ................................................................ 1-2Shielding of cables ........................................................ 1-2Earthing of shielding and electronic circuits .................. 1-2Switching of capacitive loads ........................................ 1-2Switching off inductive loads......................................... 1-2Disturbance suppression circuit - RC and DIODE ........ 1-3
Power Supply Contents........................................................................ 2-1Connection pins ............................................................ 2-2Recommended connection ........................................... 2-2Connections to be avoided ........................................... 2-3
Video terminal VT330CE
Contents........................................................................ 3-1Technical characteristics............................................... 3-2Front view ..................................................................... 3-4Customizing label.......................................................... 3-6Rear view ...................................................................... 3-7Dimensions and Cut-out................................................ 3-9Accessories................................................................... 3-10
Video terminal VT585CE
Contents........................................................................ 4-1Technical characteristics............................................... 4-2Front view ..................................................................... 4-4Customizing label.......................................................... 4-5Rear view ...................................................................... 4-6Dimensions and Cut-out................................................ 4-8Accessories................................................................... 4-9Calibration of Touch Screen.......................................... 4-9
Video terminal VT595CE
Contents........................................................................ 5-1Technical characteristics............................................... 5-2Front view ..................................................................... 5-4Customizing label.......................................................... 5-5Rear view ...................................................................... 5-6Dimensions and Cut-out................................................ 5-8Accessories................................................................... 5-9Calibration of Touch Screen.......................................... 5-9
CONTENTS
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
iv
Inserting customized labels
Contents........................................................................ 6-1Label ............................................................................. 6-2Warnings ....................................................................... 6-2Notes............................................................................. 6-4
Mounting the terminal within the container
Contents........................................................................ 7-1Using nuts ..................................................................... 7-2
Communication ports Contents........................................................................ 8-1General notes................................................................ 8-2COM1 serial port ........................................................... 8-3LPT parallel port............................................................ 8-4Mouse PS/2 port ........................................................... 8-5Keyboard PS/2 port....................................................... 8-6Ethernet network port.................................................... 8-7USB serial port .............................................................. 8-8MSP, ASP and CAN serial ports ................................... 8-9
VTCE video terminal accessories
Contents........................................................................ 9-1Adapter PC 25F <-> VTCE 9M ..................................... 9-3Cell battery .................................................................... 9-4Ethernet crossover cable .............................................. 9-5Null modem cable PC 25F <-> VTCE 9F ...................... 9-6Null modem cable PC 9F <-> VTCE9F ......................... 9-7Protfilm10/12 ................................................................. 9-8CIB board - MSP, ASP.................................................. 9-10CIB board - MSP, CAN ................................................. 9-11
Basic concepts Contents........................................................................ 10-1RAM .............................................................................. 10-2Flash Disk ..................................................................... 10-2Storage Card................................................................. 10-2Saving the Registry ....................................................... 10-2
Using the system Contents........................................................................ 11-1Calibrating the Touch Screen........................................ 11-2Enabling communication with remote terminals............ 11-3Direct PC / VTCE connection using Ethernet................ 11-4Connection in Ethernet.................................................. 11-10PC / VTCE connection using serial port........................ 11-14Automatic execution of applications.............................. 11-19Managing the Fonts ...................................................... 11-21
Resistance to chemical substances
Contents........................................................................ 12-1Chemical substances .................................................... 12-2Cleaning the VTCE ....................................................... 12-7
Software compatibility Contents........................................................................ 13-1Movicon......................................................................... 13-2
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
v
Minimum HW requirements........................................... 13-2Zenon............................................................................ 13-3
Creating a project with Movicon
Contents........................................................................ 14-1Installation..................................................................... 14-2The project .................................................................... 14-3Transferring Movicon files to a VTCE ........................... 14-3Transferring a project to a VTCE .................................. 14-4
Creating a project with ZenOn
Contents........................................................................ 15-1Installation..................................................................... 15-2The project .................................................................... 15-3Choosing the device to connect to the VTCE ............... 15-5Entering the variables ................................................... 15-8Transfer of ZenOn files to VTCE terminal ..................... 15-11Transferring a project to the VTCE terminal.................. 15-12
Technical support Contents........................................................................ 16-1International Customer Care......................................... 16-2International Product Returns ....................................... 16-2
Index ...................................................................................... IA-1
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
F-1
Foreword
The commissioning manual is valid for all types of CE Video Terminal.
The manual The commissioning manual is a source of information on securing and con-necting the terminals, on the available optional accessories and on the ini-tial software settings needed to ensure the panels work properly.
Its purpose The manual contains all the notions, concepts and examples necessary to be able to install quickly and easily.
Conventions Below are listed the symbols and styles found in the manual together with their respective meanings:
File > Open This style is used to indicate a menu option. It represents the complete path necessary for reaching the option required.
Label This style is used to indicate a data input field.
PLC Programmable logic control or other intelligent device equipped with a serial connection.
Device Intelligent device or PLC equipped with a serial connec-tion.
Identifies a key or touch button.
Identifies an option within a window.
Identifies a folder.
Indicates an important point that requires attention.
There is a danger that the equipment will be damaged.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
I-1
Introduction
What is a CE Video Terminal
A CE VIDEO TERMINAL (VTCE) is a device that is part of the Handheld PC category with which the Windows® CE operating system programmed and can be loaded and which can run supervisory programs that control or simply monitor a productive process. It can send commands using con-figured by the user; it can send data determining the process on hand and can display information deriving from the productive process. The informa-tion can be in the form of an Alarm, an Information (Info-) Message or in binary data format.
The VTCEs can be divided into two groups: those with a keyboard and those without but equipped with a Touch Screen.
All VTCEs can be supplemented with accessories to boost and broaden their performance, for example, by using the CIB board a connection can be made to a CAN network and/or to over 90% of devices on the market that are supported by ESA.
To operate the VTCE a project needs to be created (using supervisory or similar programs) that must be loaded into the VTCE (see “Chapter 13 -> Software compatibility“).
For detailed information on individual VTCEs see the relevant chapters below.
A characteristic of VTCE terminals is to have startup time of up to 30 seconds from switching on.
While in the startup phase the display remains inactive and there is nothing to be seen.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
1-1
Chapter 1 General information on electromagnetic compatibility (EMC)
Contents Page
Laying cables 1-2
Shielding of cables 1-2
Earthing of shielding and electronic circuits 1-2
Switching of capacitive loads 1-2
Switching off inductive loads 1-2
Disturbance suppression circuit - RC and DIODE 1-3
This chapter consists of 4 pages.
CHAPTER 1General information on electromagnetic compatibility (EMC)
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
1-2
Electronic devices are being increasingly used in automated systems. pro-grammable controllers (like the PLC) belong to this category, as do Man-machine-interface systems (e.g. the CE Video Terminal), control sys-tems (e.g. diagnostic terminals), interface elements (e.g. interface boards) and AC-DC drives. Together with this type of electronic apparatus, you find installed classical electro-mechanical devices like contactors, elec-tro-valves, motors etc.Electrical disturbances caused by the operation of these devices can com-promise the smooth functioning and the length of the working life of the electronic devices present on the same switchboard or the same plant. To get the best out of both the electrical and the electronic devices it is neces-sary to reduce electrical disturbance.
Laying cables Remember to lay measurement, monitoring and communication cables so that they are kept apart from power cables. Power cables laid close and par-allel to communication cables can cause coupling voltages that are strong enough to disturb or destroy electronic components.
Shielding of cables
It is essential to use suitably shielded cables for communication signal con-nections (total shielding is recommended). The shielding must be con-nected to the zero potential.
Earthing of shielding and electronic circuits
With many devices the "0V" is connected to the earth. The signal ground must be earthed but it is best to separate the ground of the shields and cir-cuits from that of the power circuits. Note that the earth can only perform its function if the "Resistance of the earth circuit" is within the max. limits prescribed.
Switching of capacitive loads
The current peaks which occur when capacitive loads are switched on can damage or destroy control devices. Furthermore, the high-frequency com-ponent of the current peak can cause serious disturbance in electronic cir-cuits as a result of inductive coupling between the connection cables.
Switching off inductive loads
When an inductive load is switched off, the magnetic energy stored tends to oppose this, discharging a voltage peak down the line which can damage or destroy the control device. Furthermore, the high-frequency component of the voltage peak can cause disturbance caused by capacitive coupling between the connection cables. The physical structure and characteristics of an inductive load make it impossible to carry out switching without disturbance unless suitable mea-sures are taken. The disturbance can be at least partially suppressed by fit-ting a suitable disturbance-suppression module in parallel with the inductive load. The disturbance-suppression module must not constitute an additional load during the work phase. Electrical disturbance is propagated both through the connection cables and electromagnetic transmission. If the disturbance is propagated by cable or electromagnetic transmission, it is much more difficult to suppress at the inputs to the units in the danger zone than it is to suppress the disturbance at its source. If the disturbance is cre-
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
1-3
ated by connection cables or by electronic transmission, it is much more difficult to suppress it at the inputs of the devices in dangerous areas than at source,
If possible, disturbance should be suppressed at source.
Disturbance suppression circuit - RC and DIODE
In the following tables there are the specifications of the disturbance sup-pression filter ciruits.
Table 1.1: Disturbance suppression circuit RC
Circuit Advantages Disadvantages
The residual component has a very low harmonic wave form component.
The best results are obtained by sizing the R/C suitably.
The residual overvoltage can be limited to the very low values by optimizing the sizing.
Volume directly proportional to the inductance and power of the load.
Switch-off time delay very low.Optimal suppression is obtained as a direct consequence of a significant de-energizing delay.
The effectiveness of the disturbance suppression is not affected by the volt-age value. No switch-on delay.
The presence of the capacitor causes a high load current peak when switching on (and can cause pasting of the con-tact if undersized).
Suitable for both AC and DC; no prob-lem with reversed polarity.
The RC circuit constitutes an additional load when used with AC.
No arc (low energy) on switching con-tact.
--
Table 1.2: Disturbance suppression circuit DIODE
Circuit Advantages Disadvantages
Very compact. High switch-off delay time.
No residual voltage (total damping of disturbance impulse).
For direct current (DC) applications only.
Easy to size. Polarity must be respected.
--Switch-off delay can lead to the forma-tion of a strong electric arc.
--Sensitive to disturbance voltage pulses in power supply circuit.
C
RUb
S
L
C R
Ub
S
L D
D
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
2-1
Chapter 2 Power Supply
Contents Page
Connection pins 2-2
Recommended connection 2-2
Connections to be avoided 2-3
This chapter consists of 4 pages.
CHAPTER 2Power Supply
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
2-2
Use a 24VDC (18..32Vdc) power supply unit to power the VTCE.
Connection pins
Check all connections before switching on.
Recommended connection
We recommend a wiring scheme as set out below in the interests of avoid-ing damaging the VTCE.
Correct earthing is essential.
Table 2.1: 4 pin Power Supply Connector
Connector Pin Meaning
1 Input power +24Vdc
2 Input power 0Vdc
3 Not connected
4 Earth protection
4 3 2 1
N.C. 24VDC- +
Table 2.2: Power supply with 0Vdc connected to PE
~
+-24V
3
+24VPE
0V
VTCE
PLC
PENL1
4
12
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
2-3
Connections to be avoided
The connections illustrated below must not be made as they may cause the VTCE to be damaged.
The above configurations will seriously damage certain compo-nents of the VTCE.
Beware of appliances with the POSITIVE connected to PE.
It is vital that the earth of the devices connected to the serial and/or parallel communication ports have the same voltage as the
0V supply of the VTCE. The circulation of current between the 0V sup-ply and the earth of the communication ports could damage certain components of the VTCE or of the devices connected it.
Table 2.3: Connections to be avoided
~
+- 24V
PENL1
~
+- 24V
PENL1
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-1
Chapter 3 Video terminal VT330CE
Contents Page
Technical characteristics 3-2
Front view 3-4
Customizing label 3-6
Rear view 3-7
Dimensions and Cut-out 3-9
Accessories 3-10
This chapter consists of a total of 10 pages.
CHAPTER 3Video terminal VT330CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-2
Technical characteristics
The following table lists the principal technical characteristics of the prod-uct in question.
Code of terminal Characteristics of the terminalVT330CE 0T0 00VT330CE 1T0 00VT330CE 2T0 00Display ▼ ▼ ▼
Type LCD 65k colors TFT ● ● ●
Touch screen --Representational format Graphic ● ● ●
Resolution [pixels] 640 x 480 (10,4”) ● ● ●
BacklightingType Lamp CCFL ● ● ●
Min. lamp-life at 25°C [hours] 20000 ● ● ●
ProcessorType Intel® Strong ARM Sa1110 206Mhz ● ● ●
KeyboardNon-customizable function keys 12 ● ● ●
Customizable function keys 16 ● ● ●
Function key LEDs 16 ● ● ●
Alphanumeric keys 27 ● ● ●
Operational keys 19 ● ● ●
Operational key LEDs 3 ● ● ●
Diagnostic LEDs 3 ● ● ●
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-3
System memory ▼ ▼ ▼
Data memory (RAM) 64Mb ● ● ●
Resident flash array 32Mb ● ● ●
InterfacesMSP serial port RS232/RS422/RS485/TTY-20mA ● ●
ASP serial port RS232/RS485 ●
Standard serial port RS232 ● ● ●
Parallel port Bidirectional ● ● ●
USB port 1 (Master) ● ● ●
Mouse PS/2 port 1 ● ● ●
Keyboard PS/2 port 1 ● ● ●
PCMCIA Type I slot 2 ● ● ●
AccessoriesConnectable accessories See table ”Chapter 9” ● ● ●
ClockClock Hardware (With back-up battery) ● ● ●
Networks
IntegratedEthernet 10/100Mbit RJ45 ● ● ●
CAN Open (Optoisolated interface) ●
Technical dataPower supply 24Vdc (18..32Vdc)Power absorbed at 24Vdc 20WProtection fuse Ø5x20mm - 3,15A Quick Blow FProtection level IP65 (front-end)Working temperature 0..50°CStorage and transportation temperature -20..+65°CHumidity (non-condensing) <85%Weight 4000grDimensionsExternal L x H x D [mm] 435 x 260 x 90Cut-out L x H [mm] 403 x 240CertificationCertifications and approvals CEInstalled softwareOperating system Microsoft® Windows® CE 3.0
Code of terminal Characteristics of the terminalVT330CE 0T0 00VT330CE 1T0 00VT330CE 2T0 00
CHAPTER 3Video terminal VT330CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-4
Front view
Key Function
1 Display
2 Alphanumeric + operative keys
3 F-keys with no LED
4 F-keys with one LED (At present the LEDs are not managed)
5F-keys with one LED (From F25 to F28 all LEDs currently not managed)
6X0 LED. Blinks when communication error is detected(At present not managed)
7 Power LED. Lights up when power in ON
8Battery LED. Lights up when the battery has nearly run out(At present not managed)
Starts input (At present not managed)
Confirms setting of data
Page upWhen in setting phase, edits dynamic text
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-5
Page downWhen in setting phase, edits dynamic text
Moves the cursor between settable fieldsWhen in setting phase, moves cursor to the left of the field
Moves the cursor between settable fieldsWhen in setting phase, moves cursor to the right of the field
Quits: setting of data, info-messages, sequence directory, com-munication driver
Displays info-messages (At present not managed)
Displays ISA alarms (At present not managed)
Displays according to context: information message help, alarm help or page help (At present not managed)
Acknowledgment of ISA alarms on display(At present not managed)
Print the entire display area
No predefined function (At present not managed)
No predefined function
No predefined function
No predefined function
In setting phase restores the initial value of the field
+ Acknowledges all ISA alarms (At present not managed)
+Displays the contents of the alarm buffer (At present not managed)
Key Function
CHAPTER 3Video terminal VT330CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-6
Customizing label
The total thickness of the label must not exceed 125µm (microme-ters). Do not use either stiff materials or glues.
Before starting to insert the customized label, see “Chapter 6 -> Inserting customized labels“.
Position Function - Dimensions L x H (mm)
1 ESA Logo, VT Model - 162 x 13
2 F-key customization F - 17 x 207
21
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-7
Rear view
Table 3.1: Connector lay-out (Part 1 of 2)
Position Function
A Standard serial port
B Mouse PS/2 port
C CAN port (Optional with CIB board)
DASP serial port for communicating with PC or other devices (Optional with CIB board)
A
C
D
E
B
H
I
F
G
M
L
CHAPTER 3Video terminal VT330CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-8
EMSP serial port for communicating with PLC/PC (Optional with CIB board)
F LPT port for connecting printer
G Keyboard PS/2 port
H Ethernet network 10/100Mbit RJ45
I USB serial port
L PCMCIA Type I slot
M Power supply connector
Table 3.1: Connector lay-out (Part 2 of 2)
Position Function
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-9
Dimensions and Cut-out
CHAPTER 3Video terminal VT330CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
3-10
To fix the sealing gasket and secure the VTCE to the container see “Chapter 7 -> Mounting the terminal within the container“.
Where accessories need to be fixed in or onto the VTCE terminal, you are advised to do this before securing the VTCE to its con-
tainer.
Accessories Any accessories should be mounted in accordance with the instructions in the relevant chapter (see “Chapter 9 -> VTCE video terminal accessories“).
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-1
Chapter 4 Video terminal VT585CE
Contents Page
Technical characteristics 4-2
Front view 4-4
Customizing label 4-5
Rear view 4-6
Dimensions and Cut-out 4-8
Accessories 4-9
Calibration of Touch Screen 4-9
This chapter consists of 12 pages.
CHAPTER 4Video terminal VT585CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-2
Technical characteristics
The following table lists the principal technical characteristics of the prod-uct in question.
Code of terminal Characteristics of the terminalVT585CE 0T0 00VT585CE 1T0 00VT585CE 2T0 00Display ▼ ▼ ▼
Type LCD 65k colors TFT ● ● ●
Touch screen Analog ● ● ●
Representational format Graphic ● ● ●
Resolution [pixels] 640 x 480 (10,4”) ● ● ●
BacklightingType Lamp CCFL ● ● ●
Min. lamp-life at 25°C [hours] 20000 ● ● ●
ProcessorType Intel® Strong ARM Sa1110 206Mhz ● ● ●
KeyboardNon-customizable function keys --Customizable function keys --Function key LEDs --Alphanumeric keys --Operational keys --Operational key LEDs --Diagnostic LEDs --
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-3
System memory ▼ ▼ ▼
Data memory (RAM) 64Mb ● ● ●
Resident flash array 32Mb ● ● ●
InterfacesMSP serial port RS232/RS422/RS485/TTY-20mA ● ●
ASP serial port RS232/RS485 ●
Standard serial port RS232 ● ● ●
Parallel port Bidirectional ● ● ●
USB port 1 (Master) ● ● ●
Mouse PS/2 port 1 ● ● ●
Keyboard PS/2 port 1 ● ● ●
PCMCIA Type I slot 2 ● ● ●
AccessoriesConnectable accessories See table ”Chapter 9” ● ● ●
ClockClock Hardware (With back-up battery) ● ● ●
Networks
IntegratedEthernet 10/100Mbit RJ45 ● ● ●
CAN Open (Optoisolated interface) ●
Technical dataPower supply 24Vdc (18..32Vdc)Power absorbed at 24Vdc 20WProtection fuse Ø5x20mm - 3,15A Quick Blow FProtection level IP65 (front-end)Working temperature 0..50°CStorage and transportation temperature -20..+65°CHumidity (non-condensing) <85%Weight 4000grDimensionsExternal L x H x D [mm] 346 x 260 x 90Cut-out L x H [mm] 314 x 240CertificationCertifications and approvals CEInstalled softwareOperating system Microsoft® Windows® CE 3.0
Code of terminal Characteristics of the terminalVT585CE 0T0 00VT585CE 1T0 00VT585CE 2T0 00
CHAPTER 4Video terminal VT585CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-4
Front view
All buttons and signals are defined via the programming software (see “Chapter 13 -> Software compatibility“).
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-5
Customizing label
The total thickness of the label must not exceed 125µm (microme-ters). Do not use either stiff materials or glues.
Before starting to insert the customized label, see “Chapter 6 -> Inserting customized labels“.
Position Function - Dimensions L x H (mm)
1 ESA Logo, VT Model - 160 x 12
1
CHAPTER 4Video terminal VT585CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-6
Rear view
Table 4.1: Connector lay-out (Part 1 of 2)
Position Function
A Standard serial port
B Mouse PS/2 port
C CAN port (Optional with CIB board)
DASP serial port for communicating with PC or other devices (Optional with CIB board)
A
C
D
E
B
H
I
F
G
M
L
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-7
EMSP serial port for communicating with PLC/PC (Optional with CIB board)
F LPT port for connecting printer
G Keyboard PS/2 port
H Ethernet network 10/100Mbit RJ45
I USB serial port
L PCMCIA Type I slot
M Power supply connector
Table 4.1: Connector lay-out (Part 2 of 2)
Position Function
CHAPTER 4Video terminal VT585CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-8
Dimensions and Cut-out
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-9
To fix the sealing gasket and secure the VTCE to the container see “Chapter 7 -> Mounting the terminal within the container“.
Where accessories need to be fixed in or onto the VTCE terminal, you are advised to do this before securing the VTCE to its con-
tainer.
Accessories Any accessories should be mounted in accordance with the instructions in the relevant chapter (see “Chapter 9 -> VTCE video terminal accessories“).
Calibration of Touch Screen
The screen of VT585CE is made of resistive, sensitive glass; fot this type of glass to work properly it requires a calibration procedure (the terminal is already calibrated when supplied), that is, the resistive area of the glass has to be adjusted to the visible are of the display.
Should it be thought necessary to repeat the calibration procedure this can be done by following the instructions set out below.
The procedure must be carried out with great care as the preci-sion ofthe keys area depends on the callibration.
CHAPTER 4Video terminal VT585CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-10
How to perform the calibration procedure:
• Make sure the VTCE is not connected to the power supply• Remove the back cover• Identify jumper X9
• Position X9 as shown in the figure.• Reconnect the power supply and switch on the terminal; the following
mask appears:
Calibration
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
4-11
The calibration has finished:• Switch off the terminal• Reposition X9 in its original position• Replace the back cover• Switch on the terminal again
The calibration procedure has finished; if the calibration has be carried out wrongly or imprecisely, repeat the procedure.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-1
Chapter 5 Video terminal VT595CE
Contents Page
Technical characteristics 5-2
Front view 5-4
Customizing label 5-5
Rear view 5-6
Dimensions and Cut-out 5-8
Accessories 5-9
Calibration of Touch Screen 5-9
This chapter consists of 12 pages.
CHAPTER 5Video terminal VT595CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-2
Technical characteristics
The following table lists the principal technical characteristics of the prod-uct in question.
Code of terminal Characteristics of the terminalVT595CE 0T0 00VT595CE 1T0 00VT595CE 2T0 00Display ▼ ▼ ▼
Type LCD 65k colors TFT ● ● ●
Touch screen Analog ● ● ●
Representational format Graphic ● ● ●
Resolution [pixels] 800 x 600 (12,1”) ● ● ●
BacklightingType Lamp CCFL ● ● ●
Min. lamp-life at 25°C [hours] 10000 ● ● ●
ProcessorType Intel® Strong ARM Sa1110 206Mhz ● ● ●
KeyboardNon-customizable function keys --Customizable function keys --Function key LEDs --Alphanumeric keys --Operational keys --Operational key LEDs --Diagnostic LEDs --
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-3
System memory ▼ ▼ ▼
Data memory (RAM) 64Mb ● ● ●
Resident flash array 32Mb ● ● ●
InterfacesMSP serial port RS232/RS422/RS485/TTY-20mA ● ●
ASP serial port RS232/RS485 ●
Standard serial port RS232 ● ● ●
Parallel port Bidirectional ● ● ●
USB port 1 (master) ● ● ●
Mouse PS/2 port 1 ● ● ●
Keyboard PS/2 port 1 ● ● ●
PCMCIA Type I slot 2 ● ● ●
AccessoriesConnectable accessories See table ”Chapter 9” ● ● ●
ClockClock Hardware (With back-up battery) ● ● ●
Networks
IntegratedEthernet 10/100Mbit RJ45 ● ● ●
CAN Open (Optoisolated interface) ●
Technical dataPower supply 24Vdc (18..32Vdc)Power absorbed at 24Vdc 20WProtection fuse Ø5x20mm - 3,15A Quick Blow FProtection level IP65 (front-end)Working temperature 0..50°CStorage and transportation temperature -20..+65°CHumidity (non-condensing) <85%Weight 4000grDimensionsExternal L x H x D [mm] 401 x 390 x 90Cut-out L x H [mm] 369 x 288CertificationCertifications and approvals CEInstalled softwareOperating system Microsoft® Windows® CE 3.0
Code of terminal Characteristics of the terminalVT595CE 0T0 00VT595CE 1T0 00VT595CE 2T0 00
CHAPTER 5Video terminal VT595CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-4
Front view
All buttons and signals are defined via the programming software (see “Chapter 13 -> Software compatibility“).
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-5
Customizing label
The total thickness of the label must not exceed 125µm (microme-ters). Do not use either stiff materials or glues.
Before starting to insert the customized label, see “Chapter 6 -> Inserting customized labels“.
Position Function - Dimensions L x H (mm)
1 ESA Logo, VT Model - 160 x 12
1
CHAPTER 5Video terminal VT595CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-6
Rear view
Table 5.1: Connector lay-out (Part 1 of 2)
Position Function
A Standard serial port
B Mouse PS/2 port
A
C
D
E
B
H
I
F
G
M
L
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-7
C CAN port (Optional with CIB board)
DASP serial port for communicating with PC or other devices (Optional with CIB board)
EMSP serial port for communicating with PLC/PC (Optional with CIB board)
F LPT port for connecting printer
G Keyboard PS/2 port
H Ethernet network 10/100Mbit RJ45
I USB serial port
L PCMCIA Type I slot
M Power supply connector
Table 5.1: Connector lay-out (Part 2 of 2)
Position Function
CHAPTER 5Video terminal VT595CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-8
Dimensions and Cut-out
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-9
To fix the sealing gasket and secure the VTCE to the container see “Chapter 7 -> Mounting the terminal within the container“.
Where accessories need to be fixed in or onto the VTCE terminal, you are advised to do this before securing the VTCE to its con-
tainer.
Accessories Any accessories should be mounted in accordance with the instructions in the relevant chapter (see “Chapter 9 -> VTCE video terminal accessories“).
Calibration of Touch Screen
The screen of VT595CE is made of resistive, sensitive glass; fot this type of glass to work properly it requires a calibration procedure (the terminal is already calibrated when supplied), that is, the resistive area of the glass has to be adjusted to the visible are of the display.
Should it be thought necessary to repeat the calibration procedure this can be done by following the instructions set out below.
The procedure must be carried out with great care as the preci-sion ofthe keys area depends on the callibration.
CHAPTER 5Video terminal VT595CE
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-10
How to perform the calibration procedure:
• Make sure the VTCE is not connected to the power supply• Remove the back cover• Identify jumper X9
• Position X9 as shown in figure.• Reconnect the power supply and switch on the terminal; the following
mask appears:
Calibration
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
5-11
The calibration has finished:• Switch off the terminal• Reposition X9 in its original position• Replace the back cover• Switch on the terminal again
The calibration procedure has finished; if the calibration has be carried out wrongly or imprecisely, repeat the procedure.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
6-1
Chapter 6 Inserting customized labels
Contents Page
Label 6-2
Warnings 6-2
Notes 6-4
This chapter consists of 4 pages.
CHAPTER 6Inserting customized labels
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
6-2
VTCE terminals are supplied with labels already set in the appropriate spaces.
If it is necessary to customize keys, the logo or the model the labels can be replaced with the neutral ones supplied in kit with the terminal (only for F-keys) or by inserting labels of other materials provided they conform with the points set out below.
Failure to follow the following indications may cause damage to the terminal.
Label The label must be of a material that is flexible and does not exceed 125µm (micrometers).
Use neither stiff materials nor glues.
Warnings Before starting to insert the customized label the following points MUST BE observed:
• Remove the label already inserted.• Follow the indications set out in the paragraph Label.• Do not use compressed air to help insert the label. • Do not use rigid or other instruments to insert the label.• Do not fold the label between the terminal and the casing. The following
figures illustrate the correct and the incorrect positions for the label.
Correct insertion:
The label illustrated is free and creates no tension on the keyboard.
Container Metal support
Thickness of sticker Keyboard
Label
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
6-3
INCORRECT insertion which could cause compromised adhesion:
The labels illustrated generate pressure that over time could cause the keyboard to scollare.
• The oversize part of the label must go under the back cover or in the appropriate fixing points (the choice is determined by the type of VTCE being used).
Compromised adhesion
Compromised adhesion
Back cover
Fixing points for adhesives
CHAPTER 6Inserting customized labels
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
6-4
Notes Here are some tips to make it easier to insert the label:
• Round off the corners.
• If there seems to be some resistance pull the label out and reinsert it.• If more than one label is used, insert them all at the same time.
Take care not to exceed the total thickness permitted (see Page 6-2 -> Label).
• Do not bend the label at right angles and/or do not bend them so sharply that they might be damaged.
• Slightly bend the label lengthwise to make it stiffer.
Label 1 Label 2
Index finger Thumb
Middle finger
Index finger Thumb
Middle finger
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
7-1
Chapter 7 Mounting the terminal within the container
Contents Page
Using nuts 7-2
This chapter consists of 2 pages.
CHAPTER 7Mounting the terminal within the container
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
7-2
The VTCE comes supplied with the elements necessary for mounting it within the host container and fixing the sealing gasket giving the declared level of IP protection.
Using nuts The figure below shows the front and back views of a VTCE inserted in a container. Under the figure is to be found the sequence of operations to be carried out to ensure that the fixing is correct.
After preparing the container that will host the VTCE:
• Insert the VTCE in the cut-out• Hold the VTCE against the wall• Insert first the washer then the nut into the fastener• Tighten the nuts till the gasket has a firm grip
The number and position of the hooks do not influence the fixing procedure. The illustrations are to show the way the hooks work.
Cut-out of acontainer
Video Terminal NutWasher
Pre-applied gasketStud
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-1
Chapter 8 Communication ports
Contents Page
General notes 8-2
COM1 serial port 8-3
LPT parallel port 8-4
Mouse PS/2 port 8-5
Keyboard PS/2 port 8-6
Ethernet network port 8-7
USB serial port 8-8
MSP, ASP and CAN serial ports 8-9
This chapter consists of 10 pages.
CHAPTER 8Communication ports
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-2
All VTCEs communicate with other devices by means of serial and/or par-allel communication ports. We list on the following page the individual ports with the respective type of communication and the function of the connection pins.
General notes Serial communication is particularly prone to disturbances. To limit the influ-ence of these disturbances it is necessary to use good quality shielded cables.
The table immediately below lists the characteristics of the cable we recom-mend for serial connection.
Particular care should be taken in the choice and lay-out of cables, specially with regard to the VTCE <-> Device connection serial cable.
Always:• Find the shortest route• Lay disturbed cables separately
Disconnect the power supply before connecting or disconnecting the communication cables so as to avoid possible damage to the
VTCE and/or the connected device.
Specifications of serial connection cableDirect current resistance Max. 151 Ohm/Km
Capacity coupling Max. 29pF/m
Shielding > 80% or total
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-3
COM1 serial port
The COM1 serial port consists of a D-Sub 9 pin male connector and can communicate using RS232.
Pin Signal Notes1 DCD1 IN --2 RX1 IN --
3 TX1 OUT --
4 DTR1 OUT --5 Signal GND Internal reference 0Volt
6 DSR1 IN --
7 RTS1 OUT --8 CTS1 IN --
9 RI1 IN --
COM1Standar Serial Port
9 pin male
CHAPTER 8Communication ports
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-4
LPT parallel port
The LPT parallel port consists of a D-Sub 25 pin female connector. It is used to connect directly with the printer.
Pin Signal Notes1 BSTRB STROBE Centronics
2 BPD0 D0 Centronics
3 BPD1 D1 Centronics
4 BPD2 D2 Centronics5 BPD3 D3 Centronics
6 BPD4 D4 Centronics
7 BPD5 D5 Centronics8 BPD6 D6 Centronics
9 BPD7 D7 Centronics
10 BACK ACK Centronics11 BBUSY BUSY Centronics
12 BPE PE Centronics
13 BSLCT SLCT Centronics14 BAFDT AFDT Centronics
15 BERROR ERROR Centronics
16 BINIT INIT Centronics17 BSLCTIN SLCTIN Centronics
18 GND Internal reference 0Volt
19 GND Internal reference 0Volt20 GND Internal reference 0Volt
21 GND Internal reference 0Volt
22 GND Internal reference 0Volt23 GND Internal reference 0Volt
24 GND Internal reference 0Volt
25 GND Internal reference 0Volt
LPT25 pin female
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-5
Mouse PS/2 port
The mouse PS/2 serial port consists of a Minidin 6 pin female connector and is used to connect a mouse.
Pin 4 does not provide for commuting any kind of load (coils etc.); an input disturbance at Pin 4 can cause the VTCE and therefore also
the industrial process itself to malfunction.
Strong input disturbances at Pin 4 could damage the VTCE.
Pin Signal Notes1 MSDATA Input/output open collector2 N.C. Not connected
3 Signal GND Internal reference 0Volt
4 PS2VCC Output with overload protection (Max 1A)5 MSCLK Input/output open collector
6 N.C. Not connected
MousePS/2
6 pin female
CHAPTER 8Communication ports
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-6
Keyboard PS/2 port
The mouse PS/2 serial port consists of a Minidin 6 pin female connector and is used to connect a keyboard.
Pin 4 does not provide for commuting any kind of load (coils etc.); an input disturbance at Pin 4 can cause the VTCE and therefore also
the industrial process itself to malfunction.
Strong input disturbances at Pin 4 could damage the VTCE.
Pin Signal Notes1 TPDATA Input/output open collector2 N.C. Not connected
3 Signal GND Internal reference 0Volt
4 PS2VCC Output with overload protection (Max 1A)5 TPCLK Input/output open collector
6 N.C. Not connected
KeyboardPS/2
6 pin female
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-7
Ethernet network port
The Ethernet network port is made up of a RJ45 8 pin female connector and is dedicated to network connection with other terminals, with PCs and any other device that supports this standard.
Pin Signal Notes1 TX+ --
2 TX- --
3 RX+ --4 -- Reclosing with pin 5 and 75 ohm termination
5 -- Reclosing with pin 4 and 75 ohm termination
6 RX- --7 -- Reclosing with pin 8 and 75 ohm termination
8 -- Reclosing with pin 7 and 75 ohm termination
EthernetRJ45
8 pin female
CHAPTER 8Communication ports
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-8
USB serial port
The USB serial port is made up of a 4 pin connector and is dedicated to connection with any other device that supports this standard.
Pin Signal Notes1 USBVCC Output with overload protection (Max 1A)2 USBD- --
3 USBD+ --
4 Signal GND Internal reference 0Volt
USB4 pin male
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
8-9
MSP, ASP and CAN serial ports
Serial port on the CIB communication board (optional). The VTCE termi-nal can be acquired with the board already inserted, otherwise the board may be acquired and then inserted later. For information on the board’s working, on its technical characteristics and on how to connect it, see the CIB board’s own manual.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-1
Chapter 9 VTCE video terminal accessories
Contents Page
Adapter PC 25F <-> VTCE 9M 9-3
Cell battery 9-4
Ethernet crossover cable 9-5
Null modem cable PC 25F <-> VTCE 9F 9-6
Null modem cable PC 9F <-> VTCE9F 9-7
Protfilm10/12 9-8
CIB board - MSP, ASP 9-10
CIB board - MSP, CAN 9-11
This chapter consists of 12 pages.
CHAPTER 9VTCE video terminal accessories
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-2
The video terminals are made to take a series of accessories that increase their capacity and/or functionality. This chapter shows how these accesso-ries relate to the various products. The table below shows which terminals will take which accessories.
Table 9.1: Accessories connectable to VTCE terminals
ACCESSORIESTERMINALS SUPPORTING THE ACCESSORY
VT330CE VT585CE VT595CE
Adapter PC 25 pin female -> 9 pin male ● ● ●
Lithium button cell battery 3V CR2032 ●1 ●1 ●1
Ethernet crossover cable ● ● ●
Null modem cablePC 25 pin female <-> VTCE 9 pin female
● ● ●
Null modem cablePC 9 pin female <-> VTCE 9 pin female
● ● ●
Protfilm10 -- ● --
Protfilm12 -- -- ●
CIB communication board with MSP and ASP port (only for VTxxxCE 0T000)
● ● ●
CIB communication board with MSP and CAN port (only for VTxxxCE 0T000)
● ● ●
Notes:1 - Already present on purchase
-- : not connectable
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-3
Adapter PC 25F <-> VTCE 9M
With the adapter shown below a 25 pin PC can be connected to a VTCE using the same cable as that used for the 9 pin PC connection.
The table shows how to combine adaptors and cables connection to the var-ious ports.
Table 9.2: Combination of serial transfer + adapters
PC serial VTCE serialCable Adaptor
CVCOM41102
CVCOM41202
CVCOM25F9M
9 pins COM1 ● -- --
25 pins COM1 -- ● --
25 pins COM1 ● -- ●
CVCOM25F9M
PC sideAdaptor
from 9 to 25 pins
CVCOM25F9M
CHAPTER 9VTCE video terminal accessories
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-4
Cell battery The function of the battery is to keep the internal clock, the calibration of the Touch Screen (in the case of terminals that have one) and the setting of the address of the network’s IP when there is no power supply.
The battery should be replaced about every 36 months.
• The battery needs to be changed either when the Battery LED (on the VT keyboard) comes on. Failure to change the battery will lead to the con-tents of the data memory being lost.
In the case of products with a Touch Screen, the running down and/or absence of the battery is not indicated on the screen.
• The battery must be substituted with the VT power off.
Discarded batteries should be placed in appropriate containers.
Procedure for inserting or substituting the battery:
• Check that the power supply is not connected.• Take off the hatch covering the battery compartment of the VT.• Insert the new battery checking that the polarities are correct.• Replace the hatch covering the battery compartment of the VT.• Reconnect the power supply.
Battery to be used
Lithium 3V cell battery CR2032
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-5
Ethernet crossover cable
The scheme below shows an Ethernet network crossover cable, which should be used for directly connecting the PC to the VTCE without using the company network connection.
12345678
1
3
2
6
Tx+
Rx+
Tx-
Rx-
1
3
6
2
Tx+
Rx+
Rx-
Tx-
12345678
PC SideRJ45 8 pin
VTCE SideRJ45 8 pinCVNET11002
FrontView
FrontView
CHAPTER 9VTCE video terminal accessories
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-6
Null modem cable PC 25F <-> VTCE 9F
The diagram below shows a serial cable of the Null modem type to be used when directly connecting the PC and the VTCE. Generally the connection is required when installing application packages in the terminal or for dis-playing the resources of the terminal directly on the PC.
2
3
7
6
8
Tx
Rx
GND
DSR
DCD
2
3
5
Rx
Tx
GND
5
20
CTS
DTR
4RTS 8
7
CTS
RTS
6
1
DSR
DCD
4 DTR
PC Side25 pin female
VTCE Side9 pin female
Max. 15 m.
CVCOM41202
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-7
Null modem cable PC 9F <-> VTCE9F
The diagram below shows a serial cable of the Null modem type to be used when directly connecting the PC and the VTCE. Generally the connection is required when installing application packages in the terminal or for dis-playing the resources of the terminal directly on the PC.
3
2
5
6
1
Tx
Rx
GND
DSR
DCD
2
3
5
Rx
Tx
GND
8
4
CTS
DTR
7RTS 8
7
CTS
RTS
6
1
DSR
DCD
4 DTR
PC Side9 pin female
VTCE Side9 pin female
Max. 15 m.
CVCOM41102
CHAPTER 9VTCE video terminal accessories
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-8
Protfilm10/12
This is a transparent protective film to be applied to the front of the touch screen terminal to protect it from wear on the part of external agents (see “Chapter 12 -> Resistance to chemical substances“).
Applying the film:
How to apply the adhesive film:
• Remove any trace of dirt or grease from the terminal using denaturized ethyl alcohol
• Dry the area thoroughly• Locate the adhesive part of the transparent film
• Position the film near the upper edge and smooth it down delicately
279.0
206.0
250.0
187.0
PROTFILM10 PROTFILM12
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-9
• Pass a soft cloth firmly over the edges to ensure adhesion
How to remove the adhesive film:
• To remove the film, pull upwards using the tab
CHAPTER 9VTCE video terminal accessories
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-10
CIB board - MSP, ASP
This is a communication board with a PC104 format which adds MSP and ASP ports which enable communication with all devices supported by ESA. For information on the board’s working, on its technical characteris-tics and on how to connect it, see the CIB board’s own manual.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
9-11
CIB board - MSP, CAN
This is a communication board with a PC104 format which adds MSP and CAN ports which enable communication with all devices supported by ESA. For information on the board’s working, on its technical characteris-tics and on how to connect it, see the CIB board’s own manual..
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
10-1
Chapter 10 Basic concepts
Contents Page
RAM 10-2
Flash Disk 10-2
Storage Card 10-2
Saving the Registry 10-2
This chapter consists of 4 pages.
CHAPTER 10Basic concepts
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
10-2
This chapter limits itself to introducing some simple but basic concepts to help first-time users of VTCE terminals.
Windows® CE is a standard operating system and as such none of its operational procedures and concepts have been determined by
ESA elettronica.
RAM The RAM memory is used by the system to run programs, calculations and whatever else is needed for the system to operate properly; furthermore, it is used for saving (whether manually or following the installation of an application package) all files loaded by the user.
The RAM memory is not buffered by a battery.
When the terminal is switched off all the information it contains is can-celled, including the files and programs. If it is necessary to keep the files after switching off, these must be moved to/put in a Flash Disk.
Flash Disk VTCE terminals have no hard disk but rather use a flash disk and handle this like a solid state hard disk. The files that have been loaded or the appli-cation packages that have to be kept permanently even after switching off the terminal must be placed in the folder My Computer\FlashDisk in the main root or in a sub-folder.
The FlashDisk is managed so as to guarantee the security of the data; this means that even when there is no power, the data being written at that moment will be saved.
Storage Card This is an external device (the PCMCIA is card not supplied by ESA, its supply is the responsibility of the user) that is inserted in the terminal and is used to increase the capacity of its (permanent) memory. Once the card has been inserted the system will automatically display a system folder called My Computer\Storage Card. The files that have been loaded or the applica-tion packages that have to be kept permanently even after switching off the terminal can be placed in the folder in the main root or in a sub-folder.
The card can be inserted without switching the terminal off.
Saving the Registry
As indicated earlier, the VTCE terminal uses non-permanent memory, thus, with the exception of the initial settings given by ESA, all the settings are lost when the terminal is switched off.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
10-3
The saving of the configuration register (Registry) enables the settings to be saved in the permanent memory area.
The configuration register must be saved every time there is a change of parameters, for example, following a network setting, a remote connection or the installation of an application, etc.
You are advised to carry out a “save” after each installation or each time settings are changed.
To activate this function, click on Start > Programs >
Windows Explorer or double-click on (My Computer) on the Desktop
of the terminal. Double-click on Windows, then double-click on
(Regedit). Alternatively double-click on (Regedit) on the Desktop of the terminal.
Once the saving phase has finished click on to close the window.
The saving procedure may require a few seconds.
Click on the Write.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-1
Chapter 11 Using the system
Contents Page
Calibrating the Touch Screen 11-2
Enabling communication with remote terminals 11-3
Direct PC / VTCE connection using Ethernet 11-4
Connection in Ethernet 11-10
PC / VTCE connection using serial port 11-14
Automatic execution of applications 11-19
Managing the Fonts 11-21
This chapter consists of 22 pages.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-2
Calibrating the Touch Screen
The VT5xxCE terminal is supplied already calibrated and operational; should it be thought necessary to repeat the calibration procedure, this can be done using the appropriate software function or it is so far out that the function cannot be activated, the calibration can be forced by using a hard-ware jumper (see Page 4-9 or Page 5-9).
To activate the function click on Start > Settings > Control Panel, then
double-click on (Stylus).
Then follow the instructions on screen. Once the calibration has been com-
pleted click on to accept the changes and close the window.
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Then browse the to click on Calibration.
Click on the Recalibrate.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-3
Enabling com-munication with remote terminals
To make it possible for the terminal to be connected to a PC or a remote ter-minal it is necessary to assign a name that identifies it unambiguously. The terminal is supplied with a name defined by ESA but this has to be changed for it to work properly.
To activate the function click on the Start > Settings > Control Panel,
then double-click on (Communic..).
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Enter the required name in the Device Name field.
Assign the description too, entering it in the Device Description field.
Click on the OK to accept the changes and close the window.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-4
Direct PC / VTCE connec-tion using Ethernet
This type of connection makes it possible for the PC and VTCE to exchange files simply and rapidly using Windows Explorer on the CE ter-minal. The connection utilizes the Server and Client mechanism, so it is necessary for the PC (which becomes the Server) to share its folder or fold-ers to be put at the disposal of the VTCE terminal (which becomes the Cli-ent).
For more on the folder sharing procedure see the on-line manual of the operative system installed.
The direct connection must be made by means of a crossover Ethernet net-work cable (for details on the cable see “Chapter 9 -> VTCE video terminal accessories“).
Once the physical connection has been made proceed to set the parameters as follows.
CVNET11102
You are advised to carry out all connection and disconnection oper-ations with the VTCE off.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-5
Assigning the network address to the VTCE:
Once the logical connection has been established go to the VTCE terminal and click on the Start > Settings > Control Panel and then double-click
on (Network).
The first three numbers of the IP address assigned must be the same as those of the PC with which the connection is to be made,
the fourth number must be different (example: PC - 192.168.100.1, VTCE - 192.168.100.5).
Click on to accept the changes.
Select as in the figure and click on the Properties.
Set as in the figure.
Then enter the network address in the IP Address field.
Click on the OK.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-6
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Skip setting the Identification as it is irrelevant in this phase.
Click on the OK.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-7
Testing the connection:
If required you can test whether the system is operating properly by running the command PING on the PC.
Go to the PC’s command prompt and digit ping followed by the IP address assigned to the VTCE and then confirm by pressing the Enter key (e.g. ping 192.168.100.5).
If the connections and settings have been made correctly, response strings will appear containing the IP address requested; contrariwise, if expired request strings appear, this means that there are connection problems; in this case look over the entire procedure including the connection cable.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-8
Exploring the PC:
Go to the VTCE and click on the Start > Programs > Windows Explorer
or double-click on (My Computer) on the Desktop of the terminal.
Go to the Address field, digit the name of the computer connected (e.g. \\PC).
Confirm with Enter.
The first time you try the connection, if no password has been assigned, a mask appears in which a password can be entered. If one is necessary, assign it, if not, do not compile the mask.
Click on the OK.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-9
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Answer YES or NO depending on your requirements.
The folder shared with the server PC is displayed.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-10
Connection in Ethernet
This allows the VTCE to be integrated within the company network. Once the connection has been made, the device behaves in practice like a PC except that it cannot itself put folders at the disposal of other network par-ticipants.
The physical connection must be made using a standard Ethernet network cable.
Once the physical connection has been made, the parameters can be set as follows.
Ethernet
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-11
Assigning the network address to a VTCE:
Once the logical connection has been established go to the VTCE terminal and click on the Start > Settings > Control Panel and then double-click
on (Network).
NOTE: As all parameters that are to be entered in the masks that appear below depend on the configuration of the network with
which you wish to be connected, they may be different from those given as examples in the figure. You are therefore advised to contact the net-work administrator.
Select as illustrated and click on the Properties.
Set as in the figure (see note).
Then browse the and click on Name Servers.
Set as in the figure (see note).
Click on the OK.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-12
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Testing the connection:
See Pag. 11-7 -> “Testing the connection:“
Click on the OK.
Browse the and click on Identification.
Set as in the figure (see note).
Click on the OK.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-13
Exploring the network:
Go to the VTCE and click on the Start > Programs > Windows Explorer
or double-click on (My Computer) on the Desktop of the terminal.
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Go to the Address field and enter the name of the network server (e.g. \\PC).
Confirm with Enter.
The folders available in the network are displayed.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-14
PC / VTCE connection using serial port
If this software interface (Microsoft Active Sync) is installed a PC can treat a connected VTCE terminal as if it were a resource of the PC itself.
The program can be freely downloaded from the Internet using the follow-ing address:
http://www.microsoft.com/downloads/search.asp
The connection must be made using a Null Modem serial cable (for details regarding the cable see “Chapter 9 -> VTCE video terminal accessories“).
Once the physical connection has been made, the parameters can be set as follows.
CVCOM25F9M
CVCOM41102
CVCOM25F9Mor
CVCOM41202
You are advised to carry out all connection and disconnection oper-ations with the VTCE off.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-15
Creating a remote connection on the VTCE:
Go to the VTCE and click on the Start > Programs > Windows Explorer
or double-click on (My Computer) on the Desktop of the terminal. Dou-
ble-click on the Windows, then double-click on (Remnet) and finally
double-click on (Make New Connection).
The Baud Rate value must be set at a value above 38400 otherwise the connection may not work properly.
Enter the name to be assigned to the connection.
Select as in the figure and click on the Next.
Select as in the figure and click on the Configure.
Enter the desired Baud Rate value.
Set the other parameters as in the figure.
Skip the settings for the Call Options, they are irrelevant at this stage.
Click on the OK.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-16
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Skip the settings for TCP/IP Settings, they are irrelevant at this stage.
Click on the Finish.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-17
Assigning a remote connection on the VTCE:
To activate the function click on the Start > Settings > Control Panel
then double-click on (Communic..).
Click on to accept the changes and close the window.
Proceed to save the configuration register if you want the settings to be made permanent (see “Chapter 10 -> Saving the Registry“).
Browse the and click on PC Connection.
Set as shown in the figure.
Click on the Change.
Set as shown in the figure.
Click on the OK.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-18
Making the connection between PC and VTCE:
Install Active Sync (by following the instructions on-screen) on the PC to be connected to the VTCE.
Even if there is no explicit request when the installation is over we advise you to disconnect the serial cable and restart the PC; once
it has restarted, reconnect the serial cable and try connecting with the VTCE terminal.
Once the installation has finished, and after setting the communication parameters on the PC, establish the connection.
While the program is searching for the logical connection, go to the VTCE and click on the Start > Programs > Windows Explorer or double-click
on (My Computer) on the Desktop of the terminal. Double-click on the
Windows, then double-click on (Replog). A connection window is displayed which then closes automatically when the connection is estab-lished.
The PC displays the request “establish a relationship”, answer NO and click the Next; the terminal is seen by the PC as a “Guest”, at this point close the window that is being displayed.
The VTCE is recognized by the PC by means of “Explore Resources” as “Portable device”: files can be transferred and installations carried out on the VTCE terminal.
The connection can only be made using COM, other communica-tion ports (USB, Ethernet, etc.) cannot be used and so we advise
you to deactivate them.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-19
Automatic execution of applications
When in the start phase VTCE terminal calls for an automatic execution procedure for the applications.
To do this create a on the VTCE terminal; this must be called Flash-Disk\ESA\Startup.
The name and path of the folder MUST be precisely as set out above, otherwise the files will not be found.
To create the new folder click on Start > Programs > Windows Explorer
or double click on (My Computer) on the Desktop of the terminal. Dou-ble click on the FlashDisk then click on File > New Folder.
Once the above-mentioned folder has been created you can proceed in two ways:
• Load .EXE file
Just copy the .exe file of the application directly into the previously created . To copy or move the files, see, if necessary Pag. 11-4 -> “Direct PC / VTCE connection using Ethernet“ or Pag. 11-10 -> “Connection in Ethernet“ or Pag. 11-14 -> “PC / VTCE connection using serial port“.
• The .ESA file is created and loaded
Should it be possible directly to use the executable file, proceed by creating a text file called Startup.esa putting into it the complete path of where the execurable file can be found and , if necessary, the parameters requested by the .exe file. Only one executable file is required for every row.
Example.
\FlashDisk\Demo\Demo.exe \FlashDisk\Demo\Project.prj\FlashDisk\Myfolder\Myfile.exe
The name of the file MUST be Startup.esa otherwise it will not be found.
Only invocations for .EXE files and any parameters can be added.
If the file is edited outside the VTCE terminal, it must be saved as “Unicode text document”.
CHAPTER 11Using the system
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-20
To see this folder click on the Start > Programs > Windows Explorer or
double-click on (My Computer) on the Desktop of the terminal. Dou-ble-click on the FlashDisk and then double-click on the Esa. Finally double-click on the Startup.
If there is more than one file in the Startup folder, these will be executed in the order: first the .EXE files and then the .ESA ones.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
11-21
Managing the Fonts
The VTCE terminal is supplied with a series of font already installed. If the user so desires, other fonts of the “True Type” type can be loaded.
To do this, create a on the VTCE terminal and call it Flash-Disk\ESA\Fonts.
The name of the folder and the path MUST be exactly as set out above, otherwise new fonts will not be found.
To create the new folder click on Start > Programs > Windows Explorer
or double click on (My Computer) on the Desktop of the terminal. Dou-ble click on the FlashDisk then click on File > New Folder.
At this point, all that needs to be done is choose from among the fonts loa-ded on a normal PC and copy them onto VTCE into the previously created
. To copy or move the files, see, if necessary Pag. 11-4 -> “Direct PC / VTCE connection using Ethernet“ or Pag. 11-10 -> “Connection in Ether-net“ or Pag. 11-14 -> “PC / VTCE connection using serial port“.
To see this folder click on the Start > Programs > Windows Explorer or
double-click on (My Computer) on the Desktop of the terminal. Dou-ble-click on the FlashDisk and then double-click on the Esa. Finally double-click on the Fonts.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-1
Chapter 12 Resistance to chemical substances
Contents Page
Chemical substances 12-2
Cleaning the VTCE 12-7
This chapter consists of 8 pages.
CHAPTER 12Resistance to chemical substances
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-2
All our VTCEs are built to withstand the effects of the more common chemical substances encountered in industrial and non-industrial environ-ments. Each element of the VTCE that could be exposed to these sub-stances (epoxy coating, keyboard membrane, screen surface, touch screen and gaskets), is tested to determine its degree of resistence.
The type of test is not the same for each component but changes according to the testing authority. Below is an example of a test (carried out by Alca-tel Bell).
The test procedure was as follows:
A 2 cm ball of cotton wool was immersed in the test substance and then placed on the keyboard. Two cotton wool balls with different substances were placed separately on each keyboard; this was then put in a Petri dish and kept at a temperature of 25°C for an hour; after this, the keyboard was washed in water and dried.
The keyboard was observed and the results classified as follows:• A - No visible deterioration• B - Very slight deterioration• C - Some deterioration• D - Gross damage visible
The substances not appearing in the table were not tested, so there is no information regarding their effect.
Chemical substances
The table shown below lists all the substances used for the test with their various results.
The table must nevertheless be considered an approximate guide regard chemical substances: no tests have been carried out on a
completely assembled terminal.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-3
Table 12.1: Chemical resistance data sheet (Part 1 of 5)
Substance
Parts of the VTCE Accessories
Resis-tance
Epoxypowder
coating 3
Mattkeyboard surface 2
Transpar-ent key-board
surface 1
Touch screen 2
Protective-glass Gaskets Protective 2
film
1,1,1-Trichlorethylene NS -- >24h -- >24h -- -- >24h ☺Acetaldehyde NS -- >24h -- >24h -- -- >24h ☺
Acetic acid
10% 3Y -- -- -- -- -- -- ☺20% 3Y -- -- -- -- -- -- ☺
<50% -- >24h -- >24h -- -- >24h ☺Acetone NS O >24h -- >24h >8h F >24h "Acetyl NS -- -- -- -- -- E -- "
Acid solutionsLC -- -- -- -- -- E -- ☺HC -- -- -- -- -- F -- "
Ajax NS -- >24h4 -- >24h4 -- -- -- ☺Aliphatic hydrocarbons NS -- >24h -- >24h -- -- >24h ☺
Alkaline solutionsLC -- -- -- -- -- E -- ☺HC -- -- -- -- -- F -- "
Ammonia
NS -- -- -- -- -- E -- ☺<2% -- >24h -- >24h -- -- >24h ☺5% -- -- -- -- >24h -- -- ☺
10% 3Y -- -- -- -- -- -- ☺35% 3Y -- -- -- -- -- -- ☺
Ariel NS -- >24h4 -- >24h4 -- -- -- ☺Benzene NS S -- A >24h -- -- >24h "Benzylalcohol NS -- O -- O -- -- O #Bichromate NS -- -- -- >24h -- -- >24h ☺Blown castor oil NS -- -- -- >24h -- -- -- ☺Carbon dioxide NS -- -- -- -- -- E -- ☺Castor oil NS -- >24h -- >24h -- -- >24h ☺
Caustic soda
<2% -- >24h -- >24h -- -- >24h ☺10% -- -- -- -- >24h -- -- ☺50% -- -- B -- -- -- -- "
Caustic solution CO -- O -- O -- -- O #Chloric acid NS -- -- A -- -- -- -- ☺Chlorine NS -- -- -- -- -- G -- #Legend:A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration, SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), ☺ - All the elements tested resist all the substances, " - At least one of the ele-ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50°C
CHAPTER 12Resistance to chemical substances
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-4
Chromic acid10% 6M -- -- -- -- -- -- "20% 6M -- -- -- -- -- -- "
Citric acid 5% 3Y -- -- -- -- -- -- ☺Coca Cola NS -- -- A -- -- -- -- ☺Cooking salt solution NS -- -- -- -- -- E -- ☺Copper sulphate 10% 3Y -- -- -- -- -- -- ☺Crude oil NS 3Y -- -- -- -- -- -- ☺Cutting oil NS -- >24h -- >24h -- -- >24h ☺Cyclohexanol NS -- >24h -- >24h -- -- >24h ☺Detergent NS -- -- A -- -- -- -- ☺Diesel fuel NS -- >24h A >24h -- -- >24h ☺Diethyle ether NS -- >24h -- >24h -- -- >24h ☺Dioxan NS -- >24h -- >24h -- -- >24h ☺Domestos NS -- >24h4 -- >24h4 -- -- -- ☺Downey NS -- >24h4 -- >24h4 -- -- -- ☺Edible oil NS 3Y -- -- -- -- -- -- ☺Essence of turpentine substitute NS 3Y -- -- -- -- -- -- ☺
EthanolNS -- -- A >24h >24h E >24h ☺
96% 3Y -- -- -- -- -- -- ☺Ethanol denat. NS 1M -- -- -- -- -- -- "Ethylacetate NS -- >24h -- >24h -- -- >24h ☺Ethylene glycol NS O -- A -- -- -- -- "Fantastic NS -- >24h4 -- >24h4 -- -- -- ☺
Formaldehyde
NS -- -- A -- -- -- -- ☺35Vol. 3Y -- -- -- -- -- -- ☺37% -- >24h -- -- -- -- -- ☺42% -- >24h -- -- -- -- -- ☺
Formic acid
5% 3Y -- -- -- -- -- -- ☺10% 3Y -- -- -- -- -- -- ☺
<50% -- >24h -- >24h -- -- >24h ☺Formula 409 NS -- >24h4 -- >24h4 -- -- -- ☺Gasoline/petrol NS 3Y -- A >24h >24h F >24h "Glacial acetic acid NS -- -- -- <1h -- -- <1h "
Table 12.1: Chemical resistance data sheet (Part 2 of 5)
Substance
Parts of the VTCE Accessories
Resis-tance
Epoxypowder
coating 3
Mattkeyboard surface 2
Transpar-ent key-board
surface 1
Touch screen 2
Protective-glass Gaskets Protective 2
film
Legend:A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration, SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), ☺ - All the elements tested resist all the substances, " - At least one of the ele-ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50°C
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-5
Glycerine NS -- >24h -- >24h -- E >24h ☺Glycol NS -- -- -- -- -- E -- ☺Grape juice NS -- >24h4 -- >24h4 -- -- -- ☺Gumption NS -- >24h4 -- >24h4 -- -- -- ☺High pressure steam (at >100°C) NS -- O -- O -- G O #Hydraulic fluids NS -- -- -- -- -- F -- "
Hydrochloric acid
<10% -- >24h -- >24h -- G >24h "10% 3Y -- -- -- -- -- -- ☺20% 3Y -- -- -- -- -- -- ☺
Hydrogen peroxide
<25% -- -- -- >24h -- -- >24h ☺30% -- -- A -- -- -- -- ☺
40Vol. 6M -- -- -- -- -- -- "Isopropanol NS S >24h A >24h -- -- >24h "Jet Dry NS -- >24h4 -- >24h4 -- -- -- ☺Lactic acid 5% 3Y -- -- -- -- -- -- ☺Lemon juice NS -- B4 -- B4 -- -- -- "Lenor NS -- >24h4 -- >24h4 -- -- >24h ☺Linseed oil NS 3Y >24h -- >24h -- -- >24h ☺Liquid allum NS -- -- -- -- -- E -- ☺Methane NS -- -- -- -- -- F >24h "Methanol NS -- >24h A >24h -- F -- "Methyl ethyl ketone NS -- >24h -- >24h -- -- >24h ☺Methylene Chloride NS 1M O -- O -- G O #Milk NS -- >24h4 -- >24h4 -- -- -- ☺Mineral acids CO -- O -- O -- -- O #Mineral oil 0-180 NS -- -- A -- -- E -- ☺Mustard NS -- >24h4 -- >24h4 -- -- -- ☺n-Butanol NS S -- -- -- -- -- -- "Nitrate of ammonia SA 3Y -- -- -- -- -- -- ☺
Nitric acid
<10% -- >24h D >24h -- G >24h "10% 3Y -- -- -- -- -- -- ☺20% 3Y -- -- -- -- -- -- ☺50% 1M -- -- -- -- -- -- "
Table 12.1: Chemical resistance data sheet (Part 3 of 5)
Substance
Parts of the VTCE Accessories
Resis-tance
Epoxypowder
coating 3
Mattkeyboard surface 2
Transpar-ent key-board
surface 1
Touch screen 2
Protective-glass Gaskets Protective 2
film
Legend:A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration, SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), ☺ - All the elements tested resist all the substances, " - At least one of the ele-ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50°C
CHAPTER 12Resistance to chemical substances
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-6
Nitrocellulose solvents NS -- -- -- -- -- G -- #Oil NS -- -- -- -- -- E -- ☺Oleic acid NS 3Y -- -- -- -- -- -- ☺Paraffin oil NS 3Y >24h -- >24h -- -- >24h ☺Perchloroethylene NS -- -- -- >24h -- G >24h "Persil NS -- >24h4 -- >24h4 -- -- -- ☺
Phosphoric acid
10% 3Y -- -- -- -- -- -- ☺20% 3Y -- -- -- -- -- -- ☺50% 3Y -- -- -- -- -- -- ☺
<30% -- >24h -- >24h -- -- >24h ☺Photographic chemicals NS -- -- -- -- -- E -- ☺Potassium carbonate NS -- >24h -- >24h -- -- >24h ☺Potassium ferrocyanide NS -- >24h -- >24h -- -- >24h ☺
Potassium hydroxide10% 3Y -- -- -- -- -- -- ☺20% 3Y -- -- -- -- -- -- ☺
Sea water NS -- -- -- -- -- E -- ☺Sebacic acid SA 3Y -- -- -- -- -- -- ☺Silicon grease NS -- -- -- -- -- E -- ☺Silicon oil NS -- -- -- >24h -- E >24h ☺Skydrol NS 6M -- -- -- -- -- -- "Sodium carbonate SA -- >24h -- -- -- -- -- ☺Sodium chloride 3% 3Y -- -- -- -- -- -- ☺Sodium hydroxide 20% 3Y -- -- -- -- -- -- ☺
Sodium hypochloride
NS -- >24h -- -- -- -- -- ☺10% 6M >24h -- -- -- -- -- "
<20% -- -- -- >24h -- -- >24h ☺Softner NS -- >24h -- >24h -- -- -- ☺
Sulphuric acid
<10% -- -- -- -- -- -- >24h ☺10% 3Y -- -- >24h >24h -- -- ☺28% 3Y -- A -- -- -- -- ☺50% 6M -- -- -- -- -- -- "CO -- -- -- -- -- G -- #
Tartaric acid SA 3Y -- -- -- -- -- -- ☺
Table 12.1: Chemical resistance data sheet (Part 4 of 5)
Substance
Parts of the VTCE Accessories
Resis-tance
Epoxypowder
coating 3
Mattkeyboard surface 2
Transpar-ent key-board
surface 1
Touch screen 2
Protective-glass Gaskets Protective 2
film
Legend:A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration, SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), ☺ - All the elements tested resist all the substances, " - At least one of the ele-ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50°C
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
12-7
Cleaning the VTCE
For cleaning the VTCE we recommend Denaturalised Ethyl Alcohol. Should this be insufficient for removing the impurity making it necessary to use other products, consult the tables above.
Teepol NS 3Y -- -- -- -- -- -- ☺Toluene NS 3Y >24h A >24h -- G >24h "Tomato juice NS -- B4 -- B4 -- -- -- "Tomato sauce NS -- B4 -- B4 -- -- -- "Top Job NS -- >24h4 -- >24h4 -- -- -- ☺Trichloroethylene NS S -- -- >24h -- G >24h "Turpentine oil NS -- >24h -- -- -- F -- "Turpentine substitute NS -- -- -- >24h -- -- >24h ☺Vaselline NS -- -- -- -- -- F -- "Vim NS -- >24h4 -- >24h4 -- -- -- ☺Vinegar NS -- -- D -- -- -- -- #Vortex NS -- >24h4 -- >24h4 -- -- -- ☺Washing powders NS -- >24h -- >24h -- E >24h ☺Water NS -- >24h -- -- -- E -- ☺White spirit NS 3Y -- A -- -- -- -- ☺Windex NS -- >24h4 -- >24h4 -- -- -- ☺Wisk NS -- >24h4 -- >24h4 -- -- -- ☺Wood oil NS -- -- -- -- -- F -- "Xilene NS 1Y >24h -- >24h -- -- -- ☺
Table 12.1: Chemical resistance data sheet (Part 5 of 5)
Substance
Parts of the VTCE Accessories
Resis-tance
Epoxypowder
coating 3
Mattkeyboard surface 2
Transpar-ent key-board
surface 1
Touch screen 2
Protective-glass Gaskets Protective 2
film
Legend:A - No visible degradation, B - Very slight degradation, C - Slight degradation, D - Damage visible or gross, E - Unlimited use, F - Limitated use, G - Use inad-visable, S - The surface melts, X - The surface blisters, O - The surface is destroyed, CO - Concentrated, HC - High concentration, LC - Low concentration, SA - Saturated, NS - Not specified, h - Hour(s), M - Month(s), Y- Year(s), ☺ - All the elements tested resist all the substances, " - At least one of the ele-ments tested may be damaged by the substances in question, # - All the elements tested may be damaged by the substances in question, -- Not tested.
Notes:1 - According to Alcatel Bell tests, 2 - According to DIN42115 Parts 2, 3 standards - According to raw material producers, 4 - Tested at 50°C
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
13-1
Chapter 13 Software compatibility
Contents Page
Movicon 13-2
Zenon 13-3
This chapter consists of 4 pages.
CHAPTER 13Software compatibility
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
13-2
After carrying out tests with certain types of supervision software, ESA elettronica declares them to be completely compatible with all its VTCE terminals. Below is a list of the software types tested.
Movicon Producer:
Software:
Minimum HW requirements
For the software to work properly a PC needs to be configured as set out below.
Minor applications:
• Processor: PENTIUM 233Mhz• Operative system: Windows 98 / Me• RAM Memory: 32 Mbytes• Occupation HD: 100Mbytes or more
Medium and major applications:
• Processor: PENTIUM II 350Mhz• Operative system: Windows 98 / Me / 2000 / NT 4.00• RAM Memory: 64 Mbytes• Occupation HD: 100Mbytes or more
Compatibility with VTCE
For this product compatibility is guaranteed for all VTCE terminals with Windows CE 3.0 without the optional CIB board. The versions of the soft-ware must be as follows or later.
• Movicon 9.1, Build 604 of 25-09-2002• Movicon CE 3.0, Build 104 of 25-09-2002
For information on how to install the program and on how to create a project see “Chapter 14 -> Creating a project with Movicon“.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
13-3
Zenon Producer:
Software:
Recommended HW requirements
For the software to work properly a PC needs to be configured as set out below.
• Processor: PENTIUM PENTIUM II PENTIUM II• Operative system: Windows Me Windows NT 4.0 Windows 2000/XP• RAM Memory: 32 Mbytes 64 Mbytes 256 Mbytes• Occupation HD: 500Mbytes 500Mbytes 500Mbytes
Compatibility with VTCE
For this product compatibility is guaranteed for all VTCE terminals with Windows CE 3.0 with or without the optional CIB board. The versions of the software must be as follows or later.
• Zenon 5.50 SP3• Zenon CE 5.50 SP3
For information on how to install the program and on how to create a project see “Chapter 15 -> Creating a project with ZenOn“.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
14-1
Chapter 14 Creating a project with Movicon
Contents Page
Installation 14-2
The project 14-3
Transferring Movicon files to a VTCE 14-3
Transferring a project to a VTCE 14-4
This chapter consists of 6 pages.
CHAPTER 14Creating a project with Movicon
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
14-2
This chapter deals EXCLUSIVELY with the settings and procedures nec-essary for using a Movicon project in Windows CE.
A knowledge of Movicon is indispensable in order to be able to fol-low this chapter. Without this, it is better to turn to the documen-
tation coming from the producer or the Progea Technical Assistance.
Installation The installation procedure is divided in two parts: the first consists in the installation of the basic version of Movicon, after which the update Movi-con CE is installed, which allows you to create projects for VTCE terminals (see also “Chapter 13 -> Software compatibility“).
What is set out below may be modified by Progea at any point with ESA knowing, consequently the installation procedure
described here may include some imprecision as to details.
If problems of installation are encountered or clarifications regarding the installation procedure are required, it is better to
turn to the documentation coming from the producer or the Progea Technical Assistance.
Put the Cd-Rom into the appropriate drive; if the PC’s “automatic loading notification” has been activated, the Movicon presentation will start auto-matically, if not, click on Start > Run…
Digit e:\Setup.exe and confirm with OK.
If the drive to be used is not “e:”, digit the appropriate letter.
Follow the on-screen instructions.
It is recommended that “Normal Installation” be selected for the installation phase.
Devices sup-ported by Movicon
Serial COM1
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
14-3
Once Movicon has been installed, proceed with the Movicon CE update.
Proceed as for the preceding point: if it does not start automatically click on Start > Run… and digit e:\Setup.exe then confirm with OK.
Start the installation following the on-screen instructions and taking care to set the following parameters as set out below:
• Select Device -> Handheld PC2000• Select Language -> As desidered• Select Components -> All (Recommended)• Select Communications -> All (Recommended)• Select Processor type -> Other processor (ARM, SHx, x86)
Close installation in line with the instructions.
If there is a serial cable connection between the PC and the VTCE and a connection has been established using Microsoft Active Sync (see “Chapter 11 -> Using the system“), Movicon will automatically install the files needed for handling the project. If this is not the case, the transfer to the VTCE can be carried out manually later (see Page 14-3 -> “Transferring Movicon files to a VTCE“).
The project A project can be created without having a VTCE available.
A knowledge of Movicon is indispensable in order to be able to fol-low this chapter. Without this, it is better to turn to the documen-
tation coming from the producer or the Progea Technical Assistance
Settings for projects for Windows CE
There are no special procedures and/or settings for creating a project work-ing on a VTCE terminal. You need only to keep in mind CE’s limitations. For a more detailed description, see Movicon’s on-line Guide.
Transferring Movicon files to a VTCE
The next step is to transfer all the files necessary for Movicon to handle the project on the VTCE terminal.
Before starting, check that there is a Serial connection between the PC and the VTCE (see “Chapter 11 -> Using the system“).
Use a serial cable connection and establish the connection by means of Microsoft Active Sync (see “Chapter 11 -> Using the sys-
tem“).
Click on Programs > MOVICON 9.1 > Movicon CE Installation >
CHAPTER 14Creating a project with Movicon
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
14-4
HPC2000 > MovCE English Installation.
The file transfer masks are displayed; follow the on-screen instructions.
Note:• The destination path depends on the type of support that is to take the
project:
• Hard disk -> \FlashDisk\My path\• PCMCIA -> \Storage Card\My path\
Other paths are possible, but when the VTCE terminal is switched off all the data is lost (see “Chapter 10 -> Basic con-
cepts“).
Sometimes, for reasons not attributable to ESA, the processor in the terminals is not recognized by Movicon. When this happens
contact the Progea Technical Assistance.
Transferring a project to a VTCE
Now the project is transferred.
Before starting, check that there is a Serial connection between the PC and the VTCE (see “Chapter 11 -> Using the system“).
Use a serial cable connection and establish the connection by means of Microsoft Active Sync (see “Chapter 11 -> Using the sys-
tem“).
Click on File > Export project for WinCE
Note:• The destination path depends on the type of support that is to take the
project:
• Hard disk -> \FlashDisk\My path\• PCMCIA -> \Storage Card\My path\
Other paths are possible, but when the VTCE terminal is
Select the desired.
Click on OK.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
14-5
switched off all the data is lost (see “Chapter 10 -> Basic con-cepts“).
• The final destination is the same as the source.
For example. Suppose we wish the transfer to be onto FlashDisk:
Path on PC -> C:\Programs\Progea\My projectPath on VTCE -> \FlashDisk\Programs\Progea\My project
To activate the project, double-click on the file MovCE.exe (see Page 14-3 -> “Transferring Movicon files to a VTCE“ for the path; a mask for choos-ing the project to be run is displayed.
The first time you try to connect a mask appears for entering the “Site Key” for which Progea must be asked. Should you not yet be in possession of this code, the project can be run in DEMO mode (a message appears indicating the type of mode).
If you want the project to be activated automatically on switching on the ter-minal, you will have to introduce the file Startup.esa and compile it as follows (see also “Chapter 11 -> Automatic execution of applications“).
\FlashDisk\My path\MovCe.exe \FlashDisk\My path\My project.prj
where My path must be replaced with the complete path of where the respective files are to be found. For example:
\FlashDisk\Movicon\MovCe.exe\FlashDisk\My project\My project.prj
Search the folders until you find the project to be run.
Select the desired.
Click on OK.
Compile using the code supplied by Progea.
Click on OK.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-1
Chapter 15 Creating a project with ZenOn
Contents Page
Installation 15-2
The project 15-3
Choosing the device to connect to the VTCE 15-5
Entering the variables 15-8
Transfer of ZenOn files to VTCE terminal 15-11
Transferring a project to the VTCE terminal 15-12
This chapter consists of 14 pages.
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-2
This chapter deals EXCLUSIVELY with the settings and procedures needed to use a ZenOn project with Windows CE.
A project can be created to function directly with a VTCE terminal and devices supported by Zenon or, when an optional card (CIB) is added to the terminal, projects can be created that function with VTCE terminals and all the devices supported by ESA.
A knowledge of ZenOn is indispensable in order to be able to fol-low this chapter. Without this, it is better to turn to the documen-
tation coming from the producer or the COPA-DATA Technical Assistance.
Installation The installation procedure is divided in two parts: the first consists in the installation of the basic version of ZenOn, after which the updated ZenOn CE is installed, which allows you to create projects for VTCE terminals (see also “Chapter 13 -> Software compatibility“).
What is set out below may be modified by COPA-DATA at any point with ESA knowing, consequently the installation procedure
described here may include some imprecision as to details.
Without optional CIB board
Devices sup-ported by ZenOn
With optional CIB board
All devices supported by
ESA
Serial COM1
MSP + ASP
MSP + CAN
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-3
If problems of installation are encountered or clarifications regarding the installation procedure are required, it is better to
turn to the documentation coming from the producer or the COPA-DATA Technical Assistance.
Put the Cd-Rom into the appropriate drive; if the PC’s “automatic loading notification” has been activated, the ZenOn presentation will start automat-ically, if not, click on Start > Run…
Digit e:\Setup.bat and confirm with OK.
If the drive to be used is not “e:”, digit the appropriate letter.
Follow the on-screen instructions.
It is recommended that “Complete Installation” be selected for the installation phase.
Once the ZenOn installation has been completed, proceed with the ZenOn CE update.
Proceed as for the preceding point; if it does not start automatically click on Start > Run… and digit e:\zenOn_CE_Setup.exe then confirm with OK.
Again follow the on-screen instructions.
The ZenOn CE destination folder must be the same as that in which ZenOn has been installed.
The project As already mentioned, the projects can be created work both with and with-out a CIB board. The configuration mode changes slightly depending on the type of project that you wish to create. Consequently there is an explicit indication of those operations to be carried out only when there is a CIB board. Where there is no such specification, the operations should consid-ered as common to both types of project.
A project can be created without having a VTCE available.
A knowledge of ZenOn is indispensable in order to be able to follow this chapter. Without this, it is better to turn to the documentation
coming from the producer or the COPA-DATA Technical Assistance.
Settings for projects for Windows CE
After creating a project click on File > Project configuration > project...
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-4
Note:• When using transfer by Ethernet network (b) the XXX must be replaced
with the TCP/IP address of the VTCE terminal connected and must be followed by a semi-colon ( ; ). For further details regarding the connec-tions see “Chapter 11 -> Using the system“.
Select the project WindowsCE (1).
Then select the Remote transport.
1
This mask is used to define, among other parameters, the mode of transfer of the project to the VTCE terminal (1) and the destination folder (2).
1) Transfer can be over the Serial port (a) or over the Ethernet network (b). Set as in figure (a) or (b), depending on the choice made.
2) Enter the complete destination path of the project. The path refers to the VTCE terminal.
Click on OK close the mask and accept the settings.
2
1
a
b
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-5
• The destination path depends on the support you want your project to be on:
• Hard disk -> \FlashDisk\My path\• PCMCIA -> \Storage Card\My path\
Other paths are possible, but all data is lost when the VTCE terminal is switched off (see “Chapter 10 -> Basic concepts“).
• It is sufficient to set the principal path and all the subfolders of the project will adopt the same path as their destination.
Choosing the device to connect to the VTCE
After having made the settings as shown on Page 15-3 proceed to choose the device to connect to the terminal.
Click on the Tools > Select Driver...
Direct connection
Use the list of devices to choose the one to be connected to the terminal; select it and click on Ok. A configuration window now appears. Set the parameters as required for the device to be connected. Click on the Ok to accept the changes.
The choice of the driver depends on the device to connect and the type of connection -- direct or using a CIB board (OPC Server).
The two procedures are detailed below.
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-6
Connection using CIB board (OPC Server)
Before proceeding, check that you have:• created and compiled a project using CIBWIN (see CIB board manual).• installed and correctly set OPCSrvESA (see CIB board manual).
Choose the following driver from the list of devices:
Select the driver as in the figure.
Click on the OK.
Set parameters according to the requirements of the project.
Select the OPC.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-7
Click on ... to select the OPC Server.
Select the driver as in the figure.
Click on the OK.
Set as shown in the figure.
Click on the OK.
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-8
Entering the variables
Click on the Tools > Variables list...
The information contained in the mask that is displayed depends on the driver selected (whether Direct connection or via a CIB
board).
Variable for direct connection
From the list of the types of variable supported choose the one you wish, select it and click on the Ok and a defining window appears. Set the parameters as required by the device to be connected. Click on the Ok to accept the changes, then click on Exit to accept and leave the masks that are displayed.
Variable for connection via CIB board see (OPC Server)
Before proceeding check that you have:• created and compiled a project with CIBWIN (see CIB board manual).• installed and correctly set OPCSrvESA (see CIB board manual).• selected the correct OPC Client driver (see Page 15-6 -> “Connection
using CIB board (OPC Server)“).
The types supported are: Boolean, i/u8Bit, i/u16Bit, i/u32Bit, float32 and String.
Click on the New to enter the variable.
Select the type required, for example as shown in the figure.
Click on the New.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-9
The list also includes the system variables. For their meaning see CIB board manual.
Choose the variable to import from among those defined with CIBWIN.
Click on the Selection...
Choose the variable you want.
Click on the Ok.
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-10
Complete the project with all the elements necessary.
Enter the parameters of the variable selected and imported. Complete the setting in accordance with the requirements of the project.
Click on the Ok.
The type of variable entered is highlighted.
Click on the Exit.
The type of variable entered is highlighted.
Click on the Exit.
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-11
Transfer of ZenOn files to VTCE terminal
To transfer projects, ZenOn uses a program (SysSrvCE.exe) that must be installed on the VTCE terminal which functions as a server for the trans-mission. The first time you transfer the server is activated automatically. Thereafter, every time you need to establish a communication between ZenOn and the VTCE terminal you need to activate the server manually by double-clicking on the file.
Before continuing check that there is a Serial and/or Ethernet connection (see “Chapter 11 -> Using the system“) between PC and VTCE.
The first time you transfer the project it is INDISPENSABLE to use the serial cable connection and to have established the connec-
tion by means of Microsoft Active Sync (see “Chapter 11 -> Using the system“).
Click on the Options > CE Runtime Update
Select the Source.
Certain parameters must be set: these relate to the VTCE terminal connected.
Select as in the figure.
Then select the Options.
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-12
From the Launch click on the Process. Then follow the on-line instruc-tions.
Once the transfer has been completed, exit by clicking on the Save & Exit.
Sometimes, for reasons not attributable to ESA, the processor that has been mounted on the terminal is not recognized by ZenOn,
consequently every time the message “Processor: UNKNOWN” is dis-played in the transfer mask, the operations carried put in the Sources must be repeated.
If everything works well the VTCE terminal will show a mask like that below.
Transferring a project to the VTCE terminal
When all the files ZenOn needs to manage the project on the VTCE termi-nal have been transferred the remote connection can be activated.
Click on and the mask shown below is displayed. It can be used to define a protection password to stop unauthorized users from elaborating a project.
1) Set the language wanted in display.
2) Set the parameters for Ethernet or Serial transmission (see Page 15-4 -> “Note:“).
3) Set as in figure, entering the path you want (see Page 15-4 -> “Note:“).
Select path then the Launch.
2
1
3
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-13
The first time the connection is attempted, a mask appears for entering the “Series number” that must be requested from COPA-DATA.
If the codes are correct and the remote communication is active, the toolbar for transferring to the terminal comes on.
Proceed with generating the runtime files that have to be transferred to the
VTCE terminal. Click on . The “Issue window” shows the files gener-ated.
Proceed now to the transfer of the project files. Click on . The “Issue window” shows the files transported.
Click on to set the project that must be remotely activated.
If the project requires the use of a CIB board, before activating the project on the VTCE check that:
• the OPC Server library has been installed and registered (see CIB board manual).
• the files generated by CIBWIN have been introduced (see CIB board manual).
Enter the password desired.
Click on OK.
Compile using the codes supplied by COPA-DATA.
Click on OK.
1) Remote transport NOT active.
2) Remote transport active.
1 2
CHAPTER 15Creating a project with ZenOn
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
15-14
Once the above points have been checked (only in the case of the CIB board) proceed with activating the project.
Click on to activate the remote project.
Click on to deactivate the remote project.
To activate the project without being connected with ZenOn you must dou-ble-click on the file ZenOnRCE.exe situated in the project installation folder.
If you want the switching on of the terminal automatically to activate the project, you need to introduce the file Startup.esa and compile it as below (see also “Chapter 11 -> Automatic execution of applications“).
\My path\ZENONRCE.exe
Where My path must be substituted with the complete path with which the project may be found, for example:
\FlashDisk\Zenon\My project\ZENONRCE.exe
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
16-1
Chapter 16 Technical support
Contents Page
International Customer Care 16-2
International Product Returns 16-2
This chapter consists of a total of 4 pages.
CHAPTER 16Technical support
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
16-2
International Customer Care
The International Customer Care service can be contacted by:
Telephone:++39-031757400
Fax: ++39-031751777
E-Mail: [email protected]
Web site: http://www.esahmi.it
International Product Returns
Should it be necessary to return the VTCE terminal for repair:
• Contact our International Customer Care service to authorize the return.• Fill in all parts of the form to accompany the product.
Our International Customer Care service will supply all the necessary infor-mation for returning a an item.
Thank you for your kind co-operation.
!!! IMPORTANT NOTE !!!
ESA elettronica S.p.A. will accept:• goods carriage free / freight prepaid (transport at customer’s cost).• goods carriage forward / freight collect (transport paid by ESA) only
with the prior authorization of the company.
ESA elettronica S.p.A. will reject:• any returned goods carriage forward where there has been no prior
authorization.
It is not necessary to send connectors, cables and accessories (unless they are thought to be linked to the problem indicated).
NOTE: Please complete form in BLOCK CAPITALS.
Returned goods code: ............................................
Customer Care worker contacted: ............................................................................
Date of compilation: ...../...../........ Signature: ...............................................................
ESA elettronica S.p.A. Via Padre Masciadri, 4/A - 22066 Mariano C.se (Co) ITALYTel. ++39-031757400 Fax ++39-031751777 C.F. 12508520157 P.IVA IT 02422110136
REPAIRS RETURN FORM
S/N:Product: ..............................................
Town : County:
Post Code:...................................................................... .....................
................................................. ...........................................
Compiled by :
Company :
Full address :
Customer details (must be filled in)
Tel. no. : Fax:
...............................................................................................................
...............................................................................................................
.................................................. ...................................................
Name :
Contact person (where different from above)
Tel. no. : Fax:
.................................................................................................................
.................................................. ...................................................
Device connected:
Information regarding problem (must be filled in)
...............................................................................................
Detailed description of the problem and the circumstances under which it occurs:
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
.....................................................................................................................................
Notes:
.....................................................................................................................................
.....................................................................................................................................
..........................................................................................................................
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
IA-1
Index
A
Accessories, 10, 9Accessories connectable to VTCE terminals, 2Adapter PC 25F VTCE 9M, 3Automatic execution of applications, 19
B
Basic concepts, 1
C
Calibrating the Touch Screen, 2Calibration of Touch Screen, 9Caratteristiche tecniche, 2Cell battery, 4Chemical substances, 2Choosing the device to connect to the VTCE, 5CIB board - MSP, ASP, 10CIB board - MSP, CAN, 11Cleaning the VTCE, 7Compatibility with VTCE, 2, 3COM1 serial port, 3Connection in Ethernet, 10Connection pins, 2Connection using CIB board (OPC Server), 6Connections to be avoided, 3Creating a project with Movicon, 1Creating a project with ZenOn, 1Customizing label, 6, 5
D
Dima di foratura, 9, 8Direct connection, 5Direct PC / VTCE connection using Ethernet, 4Disturbance suppression circuit - RC and DIODE, 3
E
Earthing of shielding and electronic circuits, 2Enabling communication with remote terminals, 3Entering the variables with ZenOn, 8Ethernet crossover cable, 5Ethernet network port, 7Exploring the PC, 8
F
Flash Disk, 2Frontale, 4
G
General notes, 2
I
Inserting customized labels, 1Installation of Movicon, 2Installation of ZenOn, 2International Customer Care, 2International Product returns, 2
K
Keyboard PS/2 port, 6
L
Label, 2Laying cables, 2LPT parallel port, 4
M
Managing the Fonts, 21Minimum HW requirements, 2Mounting the terminal within the container, 1Mouse PS/2 port, 5Movicon, 2MSP, ASP and CAN serial ports, 9
N
Note, 4Notes, 4Null modem cable PC 25F VTCE 9F, 6Null modem cable PC 9F VTCE9F, 7
P
PC / VTCE connection using serial port, 14Posteriore, 7
INDEX
405.1200.048.2 - Rel.: 2.00 of 15/05/2003
IA-2
Power Supply, 1Protfilm10/12, 8
R
RAM, 2Recommended connection, 2Recommended HW requirements, 3Resistance to chemical substances, 1
S
Saving the Registry, 2Settings for projects for Windows CE with Movicon, 3Settings for projects for Windows CE with ZenOn, 3Shielding of cables, 2Software compatibility, 1Standard series rear view, 6Storage Card, 2Switching of capacitive loads, 2Switching off inductive loads, 2
T
Testing the connection, 7The project with Movicon, 3The project with ZenOn, 3Transfer of ZenOn files to VTCE terminal, 11Transferring a project to a VTCE with Movicon, 4Transferring a project to the VTCE terminal with
ZenOn, 12Transferring Movicon files to a VTCE, 3
U
USB serial port, 8Using nuts, 2Using the system, 1
V
Variable for connection via CIB board see (OPC Server), 8
Variable for direct connection, 8VTCE video terminal accessories, 1
W
Warnings, 2What is a CE Video Terminal, 1
Z
Zenon, 3