400w psu tl494
-
Upload
dhimiter-koca -
Category
Documents
-
view
201 -
download
3
Transcript of 400w psu tl494
Semiconductor Components Industries, LLC, 2002
September, 2002 – Rev. 11 Publication Order Number:
AN983/D
AN983/D
A Simplified Power SupplyDesign Using the TL494Control Circuit
Prepared by: Jade H. AlberkrackON SemiconductorBipolar IC Division
This bulletin describes the operation and characteristics ofthe TL494 SWITCHMODE� Voltage Regulator and showsits application in a 400–watt off–line power supply.
The TL494 is a fixed–frequency pulse width modulationcontrol circuit, incorporating the primary building blocksrequired for the control of a switching power supply. (SeeFigure 1). An internal linear sawtooth oscillator isfrequency–programmable by two external components, RTand CT. The oscillator frequency is determined by:
fosc �1.1
RT � CTOutput pulse width modulation is accomplished by
comparison of the positive sawtooth waveform acrosscapacitor CT to either of two control signals. The NOR gates,which drive output transistors Q1 and Q2, are enabled onlywhen the flip–flop clock–input line is in low state. This
happens only during that portion of time when the sawtoothvoltage is greater than the control signals. Therefore, anincrease in control–signal amplitude causes a correspondinglinear decrease of output pulse width. (Refer to the timingdiagram shown in Figure 2).
The control signals are external inputs that can be fed intothe dead–time control (Figure 1, Pin 4), the error amplifierinputs (Pins 1, 2, 15, 16), or the feedback input (Pin 3). Thedead–time control comparator has an effective 120 mVinput offset which limits the minimum output dead time toapproximately the first 4% of the sawtooth–cycle time. Thiswould result in a maximum duty cycle of 96% with theoutput mode control (Pin 13) grounded, and 48% with itconnected to the reference line. Additional dead time may beimposed on the output by setting the dead–time control inputto a fixed voltage, ranging between 0 to 3.3 V.
Figure 1. TL494 Block Diagram
6
5
4
Dead–TimeControl
Oscillator
0–12 V
0.7 V
0.6 mA
+1
–
–
+
–
+
+2–
Q
CK
13
Reference
Q1
Q2
8
9
11
10
12
VCC
1 2 3 15 16 147
Feedback/P.W.M.Comparator Input
Flip–Flop
Output Mode Control
Dead–TimeComparator
P.W.M.Comparator
Q
Error Amplifier
RT
CT
VCC
Gnd
Vref
5.0 V
E2
C2
E1
C1
This document may contain references to devices which are nolonger offered. Please contact your ON Semiconductorrepresentative for information on possible replacement devices.
APPLICATION NOTE
http://onsemi.com
AN983/D
http://onsemi.com2
Figure 2. TL494 Timing Diagram
Capacitor CT
Feedback/P.W.M. Comp.(Pin 3)
Dead–Time Comp. (Pin 4)
Flip–FlopClock Input
Flip–FlopQ
Flip–FlopQ
Output Q1Emitter (Pin 9)
Output Q2Emitter (Pin 10)
Output ModeControl (Pin 13)
The pulse width modulator comparator provides a meansfor the error amplifiers to adjust the output pulse width fromthe maximum percent on–time, established by thedead–time control input, down to zero, as the voltage at thefeedback pin varies from 0.5 to 3.5 V. Both error amplifiershave a common mode input range from –0.3 V to (VCC –2 V), and may be used to sense power supply output voltageand current. The error amplifier outputs are active high andare ORed together at the inverting input of the pulse widthmodulator comparator. With this configuration, theamplifier that demands minimum output on time, dominatescontrol of the loop.
When capacitor CT is discharged, a positive pulse isgenerated on the output of the dead–time comparator, whichclocks the pulse steering flip–flop and inhibits the outputtransistors, Q1 and Q2. With the output mode controlconnected to the reference line, the pulse–steering flip–flopdirects the modulated pulses to each of the two outputtransistors alternately for push–pull operation. The outputfrequency is equal to half that of the oscillator. Output drivecan also be taken from Q1 or Q2, when single–endedoperation with a maximum on–time of less than 50% isrequired. This is desirable when the output transformer hasa ringback winding with a catch diode used for snubbing.When higher output drive currents are required forsingle–ended operation, Q1 and Q2 may be connected inparallel, and the output mode control pin must be tied toground to disable the flip–flop. The output frequency willnow be equal to that of the oscillator.
The TL494 has an internal 5 V reference capable ofsourcing up to 10 mA of load currents for external biascircuits. The reference has an internal accuracy of ±5% with
a thermal drift of less than 50 mV over an operatingtemperature range of 0 to 70°C.
APPLICATION OF THE TL494 IN A400 OFF–LINE POWER SUPPLY
A 5 V, 80 A line operated 25 kHz switching power supply,designed around the TL494, is shown in Figure 3, and theperformance data is shown in Table 1. A brief explanationof each section of the power supply is as follows:
AC Input SectionThe operating ac line voltage is selectable for nominal of
115 or 230 volts by moving the jumper links to theirappropriate positions. The input circuit is a full wave voltagedoubler when connected for 115 VAC operation with bothhalves of the bridge connected in parallel for added line–surgecapability. When connected for 230 VAC operation, the inputcircuit forms a standard full wave bridge.
The line voltage tolerance for proper operation is –10,+20% of nominal. The ac line inrush current, during powerup, is limited by resistor R1. It is shorted out of the circuit bytriac Q1, only after capacitors C1 and C2 are fully charged,and the high frequency output transformer T1, commencesoperation.
Power SectionThe high frequency output transformer is driven in a
half–bridge configuration by transistors Q3 and Q5. Eachtransistor is protected from inductive turn–off voltagetransients by an R–C snubber and a fast recovery clamprectifier. Transistors Q2 and Q4 provide turn–off drive to Q3and Q5, respectively. In order to describe the operation ofQ2, consider that Q6 and Q3 are turned on. Energy is
AN983/D
http://onsemi.com3
coupled from the primary to the secondary of T3, forwardbiasing the base–emitter of Q3, and charging C3 throughCR1. Resistor R3 provides a dc path for the ‘on’ drive afterC3 is fully charged. Note that the emitter–base of Q2 isreverse biased during this time. Turn–off drive to Q3commences during the dead–time period, when both Q6 andQ7 are off. During this time, capacitor C3 will forward biasthe base–emitter of Q2 through R3 and R2 causing it to turnon. The base–emitter of Q3 will now be reverse biased by thecharge stored in C3 coupled through the collector–emitter ofQ2.
Output SectionThe ac voltage present at the secondaries of T1 is rectified
by four MBR 6035 Schottky devices connected in a fullwave center tapped configuration. Each device is protectedfrom excessive switching voltage spikes by an R–C snubber,and output current sharing is aided by having separatesecondary windings. Output current limit protection isachieved by incorporating a current sense transformer T4.The out–of–phase secondary halves of T1 are crossconnected through the core of T4, forming a 1–turn primary.The 50 kHz output is filtered by inductor L1, and capacitorC4. Resistor R4 is used to guarantee that the power supplywill have a minimum output load current of 1 ampere. Thisprevents the output transistors Q3 and/or Q5 from cycleskipping, as the required on–time to maintain regulation intoan open circuit load is less than that of the devices storagetime. Transformer T5 is used to reduce output switchingspikes by providing common mode noise rejection, and itsuse is optional.
The MC3423, U1, is used to sense an overvoltagecondition at the output, and will trigger the crowbar SCR,Q8. The trip voltage is centered at 6.4 V with a programmeddelay of 40 �s. In the event that a fault condition has causedthe crowbar to fire, a signal is sent to the control section viajumper ‘A’ or ‘B.’ This signal is needed to shut down the
output, which will prevent the crowbar SCR fromdestruction due to over dissipation. Automatic over voltagereset is achieved by connecting jumper ‘A’. The controlsection will cycle the power supply output every 2 secondsuntil the fault has cleared. If jumper ‘B’ is connected, SCRQ12 will inhibit the output until the ac line is disconnected.
Low Voltage Supply SectionA low current internal power supply is used to keep the
control circuitry active and independent from externalloading of the output section. Transformer T2, Q9 and CR2form a simple 14.3 V series pass regulator.
Control SectionThe TL494 provides the pulse width modulation control
for the power supply. The minimum output dead–time is setto approximately 4% by grounding Pin 4 through R5. Thesoft start is controlled by C5 and R5. Transistor Q11 is usedto discharge C5 and to inhibit the operation of the powersupply if a low ac line voltage condition is sensed indirectlyby Q10, or the output inhibit line is grounded.
Error amplifier 1 and 2 are used for output voltage andcurrent–level sensing, respectively. The inverting inputs ofboth amplifiers are connected together to a 2.5 V referencederived from Pin 14. By connecting the two inputs together,only one R–C feedback network is needed to set the voltagegain and roll off characteristics for both amplifiers. Remoteoutput voltage sensing capability is provided, and the supplywill compensate for a combined total of 0.5 V drop in thepower busses to the load. The secondary of the outputcurrent sense transformer T4, is terminated into 36 � andpeak detected by BR1 and C6. The current limit adjust is setfor a maximum output current of 85 amperes.
The oscillator frequency is set to 50 kHz by the timingcomponents RT and CT. This results in a 25 kHz two phaseoutput drive signal, when the output mode (Pin 13) isconnected to the reference output (Pin 14).
Table 1. 400 Watt Switcher Performance Data
Conditions
Test Input Output Results
Line Regulation 103.5 to 138 Vac 5 Volts and 80 Amps 8 mV 0.16%
Load Regulation 115 Vac 5 Volts, 0 to 80 Amps 20 mV 0.4%
Output Ripple 115 Vac 5 Volts and 80 Amps P.A.R.D. 50 mV P–P
Efficiency 115 Vac 5 Volts and 80 Amps 73%
Line Inrush Current 115 Vac 5 Volts and 80 Amps 24 Amps Peak
AN983/D
http://onsemi.com4
Figure 3. 400 Watt Switchmode Power Supply
AC
INP
UT
SE
CT
ION
LOW
VO
LTA
GE
SU
PP
LY S
EC
TIO
N
PO
WE
R S
EC
TIO
N
Q1
T1
10 k
200
10 k
5 W 5 WC1
2400200 V
C2
2400 200 V
MDA2504
WhiteGreenBlack
120
1/2 W
10/5 A
3 AG
R.F.I. FilterCDE
APF520CL
MAC15–6
6–810 WR1
100
5 W
100
5 W
0.001
1 kV0.001
1 kV
1N49361N4936
4 200 V4 200 V
TIP31Q2
TIP31Q4
MJ1
3015
MJ1
3015
Q3 Q5
1N49
33 1N49
333333R2
33010 V
33010 V
++
53 W
5 V SEN5 V 80 A 5 V SEN RTN 5 V RTNOutput
10
1/2 W
10
1/2 W
1N4001
2200 10 V
7.5 k 5.1 k
Inhibit
MC3423U1
7543
8
1
+
50 V
0.0033
MB
R60
35
MB
R60
35
OU
TP
UT
SE
CT
ION
0.05
0.05
10 101/2
W
1/2
W
MB
R60
35
MB
R60
35
0.05
0.05
1010 1/2
W
1/2
W
1
L1
4.7 10 W
R4
T5
50 V1+
330
1 k 1 k
+ C446000 10 V
33C 35 U
0.01
Q8
MCR100.3 Q12
‘A’
‘B’
T4
115
230
115
230
115
T2 +35 V2200
1N4744390 1 W
Q9TIP31
MDA100 A
+16 V1000
5.1 k
5601.5 k 2.2 k
1N4933
1N4933
560
TIP32Q6
Q7TIP32
MPSA 70Q10
14.7 k
10
1N4001
+16 V330
1N40018.2 k 0.001
50 V
MPSA 55
Q11
TL494U2
OutputVoltage Adj.
8.2 k 4.7 k
361 W BR1
5 k
10 Turn
25 k
10 Turn
0.001
50 V
0.001
50 V
33 k18 k 1N4001
C6+16 V22
CT
RT0.00316 5 6
1
3
15
2
14
13
10
9
7
8
12
11 4
18 k
R5
0.1
10 k 10 k
8.2 k
0.01
50 V 1 M
EG
4750 VC5
All Capacitors in �FAll Resistors in Ohms 1/4 Watt
(unless otherwise noted)
Cur
rent
Lim
it A
dj. S
et fo
r 85
AC
ON
TR
OL
SE
CT
ION
T3
Vm 25
R35
3 W
C3
CR1
AN983/D
http://onsemi.com5
Transformer Data
T1 Core:Bobbin:Windings:
Ferroxcube EC 70–3C8, 0.002″ gap in each legFerroxcube 70PTBPrimary (Q3, Q5):Primary (Q1):Secondary, 4 each:Shield, 2 each:
50 turns total, #17 AWG Split wound about secondary.4 turns, #17 AWG.3 turns, #14 AWG Quad Filar wound.Made from soft alloy copper 0.002″ thick.
T2 Core:Bobbin:Windings:
Allegheny Ludlum EI–75–M6, 29 gaugeBobbin Cosmo EI 75Primary, 2 each:Secondary:
1000 turns, #36 AWG.200 turns, #24 AWG.
T3 Core:Windings:
Ferroxcube 846 T250–3C8Primary, 2 each:Secondary, 2 each:
30 turns, #30 AWG Bifilar wound.12 turns, #20 AWG Bifilar wound.
T4 Core:Windings:
Magnetics Inc. 55059–A2Primary, 2 each:Secondary:
1 turn, #14 AWG Quad Filar wound. Taken from secondary to T1.500 turns, #30 AWG.
T5 Core:Windings:
Magnetics Inc. 55071–A2Primary:Secondary:
4 turns, #16 AWG Hex Filar wound.4 turns, #16 AWG Hex Filar wound.
L1 Core:Windings:
TDK H7C2 DR 56 x 355 turns, soft alloy copper strap, 0.9″ wide x 0.020″ thick, 6 �H.
AN983/D
http://onsemi.com6
Notes
AN983/D
http://onsemi.com7
Notes
AN983/D
http://onsemi.com8
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to makechanges without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for anyparticular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and allliability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/orspecifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must bevalidated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applicationsintended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or deathmay occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLCand its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney feesarising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges thatSCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATIONJAPAN : ON Semiconductor, Japan Customer Focus Center2–9–1 Kamimeguro, Meguro–ku, Tokyo, Japan 153–0051Phone : 81–3–5773–3850Email : [email protected]
ON Semiconductor Website : http://onsemi.com
For additional information, please contact your localSales Representative.
AN983/D
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
Literature Fulfillment :Literature Distribution Center for ON SemiconductorP.O. Box 5163, Denver, Colorado 80217 USAPhone : 303–675–2175 or 800–344–3860 Toll Free USA/CanadaFax: 303–675–2176 or 800–344–3867 Toll Free USA/CanadaEmail : [email protected]
N. American Technical Support : 800–282–9855 Toll Free USA/Canada
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.