4007ES Operator’s Manual - Interamsa | Distribuidor Autorizado de … · 2017. 10. 12. · 4007ES...

4007ES Operator’s Manual

579-1165Rev. C

2

© 2015- 2016 Tyco Fire Protection Products. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.

TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited.

Cautions and Warnings

READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper installation.

DO NOT INSTALL ANY SIMPLEX® PRODUCT THAT APPEARS DAMAGED- Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex product supplier.

ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be performed by a representative or authorized agent of your local Simplex product supplier.

STATIC HAZARD - Static electricity can damage components. Handle as follows:• Ground yourself before opening or installing components.• Prior to installation, keep components wrapped in anti-static material at all times.

FCC RULES AND REGULATIONS – PART 15 - This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-dance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Cautions, Warnings and Copyright

3

4007ES Operator’s Manual (579-1165)

Introduction

The user interface is touchscreen based on 4007-9101 4007ES and 4007-9201 4007ES Hybrid* Fire Alarm Control Panels (FACP). The various functions of the panel are access-level protected, thus restricting access to sensitive features to appropriate personnel only.

The 4606-9202 and the 4606-9205 are Color Touchscreen LCD Annunciators for 4007ES panels. They provide remote annunciation of the FACP status. Access to Annunciator switch functions can be enabled or locked using the keyswitch. A maximum of six color touchscreen annunciators can be installed on a 4007ES panel. Refer to the Programmers’s manual, 579-1167, for more information on how to enable/disable the operations on the Color Touchscreen LCD Annunciator.

* = The user interfaces for the 4007ES and the 4007ES Hybrid FACPs are identical and referred to collectively as 4007ES in this

document.

In this publication

Reference Documents

579-1102: 4007ES Installation Manual

579-1167: 4007ES Programmer Manual

579-1110: 4007ES/4007H Service Parts List

579-1172: Color Touchscreen LCD Annunciator Installation Manual

User Interface ............................................... 4 Panel Setup ................................................................18

Alarm Conditions ........................................... 5 Alarm Log ...................................................................20

Supervisory and Trouble Conditions ........... 10 Trouble Log ................................................................21

Main Menu .................................................. 13 Search ........................................................................22

User Access Level ...................................... 14 Diagnostics .................................................................23

System Info ................................................. 16 Report Menu ..............................................................28

Index ..........................................................................31

4


User Interface Overview:

The user interface is used to operate the FACP.

Figure 1. 4007ES User Interface

Figure 2. Color Touchscreen LCD Annunciator User InterfaceTable 1. The FACP User Interface is made-up of the following components:

Touchscreen Used as the panel’s input/output interface.

Piezo Emits tones during Alarm, Trouble, Pri2 and Supervisory conditions.

Bi-color User-Defined LEDs

Associated with the three custom-configured user buttons. The top two LEDs can be either yellow or red. The bottom LED can be either yellow or green.

Slide-in Labels Used to describe the functions of the user buttons.

Fire LED Indicates a fire alarm when flashing and an acknowledged alarm when steady on.

Priority 2 LED Indicates a Priority 2 condition when flashing and an acknowledged condition when steady on.

Supervisory LED Indicates a Supervisory condition when flashing and an acknowledged condition when steady on.

Trouble LED Indicates a Trouble state when flashing and acknowledged Trouble when steady on.

Alarm Silence LED Indicates an alarm has been silenced when steady on.

Power LED Indicates AC power is applied to the panel when steady on.

Keyswitch (Only on the Color Touchscreen LCD Annunciator) Allows interaction with the panel if the key is used.

Power LED

Alarm Silenced LED

Trouble LED

Priority 2 LED

Supervisory LED

Fire LED

Slide-in LabelsBi-Color User Defined LEDsPiezo Touchscreen

Keyswitch

Power LED

Alarm Silenced LED

Trouble LED

Priority 2 LED

Supervisory LED

Fire LED

Slide-in LabelsBi-Color User Defined LEDsPiezo Touchscreen

User Interface

5


Alarm Conditions Overview:

An alarm condition occurs when an initiating device (such as a manual pull station, smoke detector, etc.) activates. The panel indicates the presence of the alarm condition by:

• Displaying messages on the user interface.

• Flashing the Fire or PRI2 LEDs.

• Activating the building’s notification appliances (horns and strobes).

Screen Buttons:

Scroll Up Scroll Down Return Accept Decline

Recognizing an Alarm Condition:

When an alarm condition occurs, the following events occur at the user interface:

Fire PRI2

1. The Fire LED begins to blink2. The piezo begins to sound a

pulsating tone3. The user interface displays the

Fire Alarm in System screen, which shows the list of all the triggered alarms.

1. The PRI2 LED begins to blink2. The piezo begins to sound a pulsating tone3. The user interface displays the PRI2 Alarm in

System screen, which shows the list of all the triggered alarms.

Note: A zone groups multiple points together, and the Zone Fire and Zone PRI2 Alarms lists dis-play all the zones where alarm conditions occurred. You can view the points that triggered the alarms within each zone by pressing on any given zone from the list.

Figure 3. Alarm Condition Screen (Fire Alarm Shown as an Example)

The piezo can be silenced by pressing anywhere on the user interface touchscreen. Until the alarm conditions are acknowledged, it will re-sound after 1 minute of inactivity at the user interface.

Piezo is emitting a pulsating tone A list of alarms is displayed

The Fire LED is blinking

DateTimeFire Alarm in System

PULL STATION 1FIRE ALARM

DateFirst of 1

MenuAlarm FunctionsACK1

The number displayed represents the number of alarms

Alarm Conditions

6


Processing Alarms: There are three actions that may be taken when an alarm condition occurs:

1. Acknowledge an Alarm2. Silence the Alarm3. Reset the System

Each step is explained in detail in the rest of this section.

Acknowledge an Alarm: Two types of acknowledging modes can be configured on the panel:

1. Global AcknowledgeAll the zones inside the Zone Alarm list are acknowledged at once.

2. Individual AcknowledgeEach zone inside the Zone Alarm list is acknowledged separately.

Global Acknowledge

Tap the ACK button.

Note: Acknowledging an alarm does not silence the horns. You need to silence an alarm as shown in the section “Silence the Alarm”.

Individual Acknowledge

Tap the unacknowledged alarm from the Zone Alarm List.

Note: The alarms that have not been acknowledged display the text “Press to acknowledge” on the top right of the button.



DateFirst of 1




DateFirst of 1


Alarm Conditions, Continued

7


Silence the Alarm: Silencing an alarm turns off all the audible notification appliances that are programmed to turn off when it is pressed.

1. Tap the Alarm Functions button.

2. Press the Alarm Silence button

3. Confirm

WARNING: Ensure the evacuation of the building is completed prior to silencing the alarm.



DateFirst of 1


Fire Alarm in System

System Reset

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Alarm Silence

Are you sure?


8


Reset the System: Resetting the system allows it to return to a normal state after alarm activation.

IMPORTANT: Reset the system only after the source of the alarm is determined and dealt with.

1, Tap the Alarm Functions button.

2. Tap the System Reset button.

3. Confirm.

Notes: 1. If a zone or device has reset successfully, the user interface returns to its normal display.

2. If a zone or device remains in alarm when you reset the system, the system reset aborts. A message confirming the abort displays on the user interface.



DateFirst of 1


Fire Alarm in System

System Reset

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Alarm Silence

Are you sure?


9


Viewing the Alarm Condition Details:

Each alarm condition contains detailed information on the point (or points) that have triggered it. To access that info:

1. Tap on a desired alarm condition from the Fire Alarm in System screen. That alarm condition can either be a point or a zone containing a variety of points. A point in alarm is shown as an example.

2. Take the necessary actions, using the buttons available at the point details screen. A pull station point is shown as an example.



DateFirst of 1


M1-1-0 PULL STATION 1

Date Time

Enable

Disable

M1-1 M1-1 PULL STATIONDEVICE ADDRESS: 2-1 TYPE: ADRPULIDNET2 CARD

UNIT NUMBER: 0 RUI NUMBER: LOCAL---------------------------------------------------------------------PRIMARY STATUS FIRE ALARMCURRENT DEVICE CORRECT DEVICEDEVICE ON-LINEPHYSICAL STATE ABNORMALRAW STATE ABNORMALACTIVE STATE OFFARMED STATE ARMEDENABLED STATE ENABLED


10


Supervisory and Trouble Conditions Overview:

A Supervisory condition indicates a problem with the building’s automatic sprinkler system or some other system used for the protection of life and property.

A Trouble condition indicates the presence of a circuit break, or a ground, within a system point, or somewhere between the FACP and one of its points. It can also be used to indicate a failure in the system that requires attention.

The panel indicates the presence of a Supervisory, or Trouble condition by:

• Displaying messages on the user interface.

• Flashing the Supervisory or Trouble LEDs.

Screen Buttons:

Scroll Up Scroll Down Return Accept Decline

Recognizing a Supervisory and a Trouble Condition:

When an Supervisory or a Trouble event occurs, the following events occur at the user interface

Supervisory Trouble

1. The Supervisory LED begins to blink.

2. The piezo begins to sound a continuous tone.

3. The user interface displays the Supervisory in System screen, which shows the list of all the Supervisory conditions.

1. The Trouble LED begins to blink.2. The piezo begins to sound a continuous tone.3. The user interface displays the Trouble in

System screen, which shows the list of all the Troubles.

Figure 3. Supervisory or Trouble Condition Screen (Trouble Conditions Shown as an Example)

DateTimeTrouble in System

ACK5

Alarm Functions Menu

CARD 1, NAC POWER SUPPLYNAC MISWIRE TROUBLE

DateFirst of 5

SYSTEM TIME/DATE INVALID OR NOT SETABNORMAL

DateMost Recent of 5

The piezo can be silenced by pressing anywhere on the user interface touchscreen. Until the Trouble and Supervisory conditions are acknowledged, it re-sounds after 1 minute of inactivity at the user interface.

Piezo is emitting a continuous tone The list of Troubles is displayed

The number displayed represents the number of Troubles and Supervisory conditions

The Trouble LED is blinking

Supervisory and Trouble Conditions

11


Processing Supervisory and Trouble Conditions:

When a Supervisory or a Trouble event occurs, it needs to be acknowledged and the cause of the event resolved for the system to return to normal. Two types of acknowledging modes can be configured on the panel.

1. Global Acknowledge

All the zones inside the Zone Supervisory or Zone Trouble lists are acknowledged at once.

2. Individual Acknowledge

Each zone inside the Zone Alarm List are acknowledged separately.

Note: A zone groups multiple points together and the Zone Supervisory or Zone Trouble list displays all the zones where Trouble or Supervisory conditions occurred.

Global Acknowledge

Tap the ACK button.

Individual Acknowledge

Tap the unacknowledged Trouble from the events list.

Note: The Troubles that have not been acknowledged display the text “Press to acknowledge” on the top right of the button.


ACK5



DateFirst of 5


DateMost Recent of 5


ACK5



First of 5


Most Recent of 5

Press to acknowledge


Supervisory and Trouble Conditions, Continued

12


Viewing the Supervisory and Trouble Conditions Details:

Each Supervisory or Trouble condition contains detailed information on the point (or points) that have triggered it. To access that info (Trouble screen is shown as an example):

1. Tap on a desired Trouble condition from the Trouble in System screen. That Trouble condition can either be a point or a zone containing a variety of points. A point in Trouble state is shown as an example.

2. Take the necessary actions, using the buttons available at the point details screen. A Time and Date Trouble is used as an example.


ACK5



First of 5


Most Recent of 5



P58 SYSTEM TIME/DATE WAS NOT SET

Date Time

On

Off Time /Date

Trouble DetailsAuto

Supervisory and Trouble Conditions, Continued

13


Main Menu Overview:

The Main Menu screen displays the functions available at the panel and can be accessed by:

• Tapping anywhere on the touchscreen to remove the screensaver image.

• Tapping the Menu button on the user interface if the user interface is in use.

Screen Buttons:

User Button 1* User Button 2* User Button 3* Return Button

* User Buttons can be assigned to custom panel functions. Each function can be assigned to a task, such as Manual evacuation or City Disconnect. User buttons that have not been assigned a function do not appear on the user interface.

Figure 4. Main Menu Screen

Main Menu Icons Description Page

System Info Use the System Info function to obtain detailed information regarding the panel and its components.

16

Panel Setup Use the Panel Setup function to modify the configuration of the basic components. 18

Alarm Log The Alarm Log screen contains the list of alarms that the panel has received. 20

Trouble Log The Trouble Log screen contains the list of Troubles that the panel has received. 21

Search Use the Search screen to look for any configured point on the system controlled by the panel.

22

System Reset Tap the System Reset button to reset all devices in alarm and clear all acknowledged Alarms, Troubles and Supervisory conditions.

8

Hardware ResetTap the Hardware Reset button to re-initialize the state of certain hardware components. A hardware reset is typically used to reset Class A Troubles after the problem causing the Trouble is resolved.

22

Diagnostics Use the Diagnostics function to run tests on the panel and the connected devices. 23

User Access Level Tap the User Access Level button to access the login screen. From this screen, the user can log into the panel with a desired access level, or log out of the access level that he is currently in.

14

Lamp TestTap the Lamp Test button to light all 9 LEDs on the front panel for 5 seconds. The three dual-colored LEDs blink alternately. The touch screen alternates between red, green and blue.

13

Report Menu Tap the Report Menu button to generate various types of reports on the system points. 27

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Main Menu

System Info Panel Setup Alarm Log Trouble Log USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Search System Reset Hardware Reset

Diagnostics

User Access Level

Lamp Test Report Menu

DateTime

Main Menu

14


User Access LevelOverview:

Tap the User Access Level button to access the login screen, where the user can log in to the panel with a desired access level, or log out of the current access level.

Notes: 1. Four access levels can be used to log in to the panel, with the lowest, User Access Level 1, being the default.

2. Only some functions are available at each access level. The User Access Level Chart (Figure 6) shows functions with associated default user access levels.

3. The ES Panel Programmer can be used to modify default user access levels for each function, or set user access level passcodes. Refer to document 579-1167: 4007ES Panel Programmer’s Manual for more details.

Screen Buttons:

Erase Accept Return

Figure 5. User Access Level Screen

User Access LevelCurrent Access Level: 1

Enter Passcode

Logout

1 ABC2

DEF3

JKL5

TUV8

WXYZ9

0

GHI4

MNO6

PQRS7

DateTime

Logout:

Tap the Log Out button to log out of the current user access level. Once logged out, the user is returned to Access Level 1.

Continued on next page

Logout

User Access Level

15


Figure 6. User Access Level Chart

System Info1

Panel Setup2

Alarm Log1

Trouble Log1

Search1

System Reset1

Hardware Reset2

Diagnostics2

User Access Level

1

Lamp Test1

Report Menu1

User Buttons 1,2 3***

Main Menu1

Card Revisions

1

Software Revisions

1

Panel Serial Number

1

Card Status1

Swap Config2

Set Time/Date2

Touchscreen Calibration

2

Mass Storage1

HW Reset2

Restart4

Walktest3

Cfig Download3

Earth Fault Search3

Earth Fault Latch2

NAC Miswire Test3

Duplicate Device Search3

Weak Answer Search3

TrueAlert Test3

TrueAlert NAC Test3

CO Algorithms3

Install Mode2

AlarmLog1

TroubleLog1

TrueAlarm Status

1

TrueAlarm Service

1

TrueAlert NAC Test

1

TrueAlert Status1

TrueAlarm CO1

Active List1

Verification Tally1

TrueAlert Self-Test

1

Main Menu1

Function Name

Default Access Level

Show Alternate Config Version

2

Use AlternateConfig

2

Location3

IDNet3

Last Result3

TrueAlert ESSelf-Test?

3

TrueAlert Device LEDs Test?3

TrueAlert Device Test Mode?3

TrueAlert Silent Test Mode?3

IViewMod2

IAddMiss3

IAddOpens3

IRemvNorm3

IRemvAll3

Log Menu1

*** = Default Access Level Configured with the ES Panel Programmer

Clear3

Clear3

Select Item1

Calibrate2

Clear2

Next Group3

Prev Group3

Select Item3

Enable3

Enable All3

Disable3

Revert3

Off3

On3

ViewRaw2

All3

Single3

Off3

On3

Off3

On3

All3

Single3

Off3

On3

ALL1

LAST1

PrtInstal1

LAST1

ALL1

Run Self-Test?3

View Test Results?3

View Last Test Results?3

View All Test Results?3

Off3

On3

Off3

On3

Off3

On3

System Upgrade

1

JobBackup

1

SaveReports

1

Upgrade Status

1

SnapShotRecovery

1

Eject USB1

Piezo Silence3

Off3

On3

NetDiag4

User Access Level, Continued

16


System Info Overview:

Use the System Info function to obtain detailed information regarding the panel and its components. Tap on a menu icon to access that option’s main screen. Refer to Figure 6 for access levels required to use each option inside the System Info screen.

Screen Buttons:

Scroll Up Scroll down Accept Return

Figure 7. System Info Screen

System Info

Card Revisions

Software Revisions

Panel Serial Number

Card Status

USER BUTTON 1

USER BUTTON 2

USER BUTTON 3

Date Time

SystemFiles Info IP Info

Card Revisions:

Tap the Card Revisions button to see a list of all the cards (modules) installed in the panel.

Software Revisions:

Tap the Software Revisions button to see the latest master revisions loaded on the panel.

Panel Serial Number:

Tap the Serial Number button to see the serial number of the panel.

Card Status:

Tap the Card Status button to see the status of the different cards installed in the panel.


Card Revision Information

Appears Here

Card Revisions DateTime

Software Revision Information

Appears Here

Software Revisions DateTime

Serial NumberAppears Here

Panel Serial Number DateTime

Card StatusAppears Here

Select Card for Status DateTime

System Info

17


System Files Info:

Tap the System Files Info button to see the latest master revisions loaded on the Remote Annunciator.

IP Info:

Tap the IP Info button to see the IP and the MAC address of the 4007ES panel.

BOOTLOADER REV: 1.01.00.03

KERNEL REV: 1.01.00.10

FILESYSTEM REV: 1.01.01.15

PANELUI: 1.01.02.16

System Files Info DateTime

IP ADDRESS: 192.168.1.150

HARDWARE ADDRESS:00:08:bd:01:dc:43

IP Info DateTime

System Info, Continued

18


Panel Setup Overview: Use the Panel Setup function to modify the configuration of the basic panel components. Tap on a menu icon to access that option’s main screen. Refer to Figure 6 for access levels required to use each option inside the Panel Setup screen.

Screen Buttons:


Figure 8. Panel Setup Screen

Panel SetupSwap Config Set Time/Date Touchscreen

CalibrationMass

StorageUSER

BUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

Swap Config:

Tap the Swap Config button to access the functions below. These functions allow roll back to the previous versions of the panel firmware.

• Show Alternate Config Version: Tap this button to display the previous version of the panel firmware.

• Use Alternate Config Version: Tap this button to install the previous version of the panel firmware.

Set Time/Date:

Tap the Set Time/Date button to access the screen where the date and time displayed at the panel can be updated:

1. Press the button that corresponds to either day, month, year, hour, minute or second.

2. Enter a new value using the touchscreen keypad.

3. Repeat steps 1 and 2 for the date and time values that remain.

4. Press the Accept button for the new date and time to take effect immediately.

Touchscreen Calibration:

Tap the Touchscreen Calibration button to access the calibration screen and adjust the sensitivity of the user interface touchscreen. Follow these steps to adjust:

1. Increase or decrease the touchscreen sensitivity by using the Scroll Up and Scroll Down buttons.

2. Tap the Calibrate button and then tap the “+” signs that appear to adjust the precision of the touchscreen pressure sensors.

3. Return to the System Menu screen.


Swap Config

Show AlternateConfig Version

Use AlternateConfig

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

Day Month Year

Hrs Mins Sec

: :

1 2 3

4 5 6

7 8 9

0

Panel Setup

0101 01

01 01 01

DateTime

Calibrate

Clear

Sensitivity

3x

Panel Setup DateTime

Panel Setup

19


Mass Storage:

Tap the Mass Storage button to access the functions listed below. The USB key must be inserted in the USB Port slot of the 4007 CPU Card for the Mass Storage button to work.

• Job Backup: Tap this button to save the job currently loaded on the panel to the USB key.

• Save Reports: Tap this button to save reports to the USB key.

• Upgrade Status: Tap this button to see the progress of the software upgrades.

• SnapShot Recovery: Tap this button before doing a system upgrade to copy the software types currently loaded on the panel to the USB key.

To upload these software types back on the panel, re-insert the USB key in the USB Port of the 4007 CPU Card and tap the SnapShot Recovery button.

• Eject USB: Tap this button to safely remove the USB from the panel.

With a USB thumb drive inserted, tap the System Upgrade button to open the System Upgrade screen which contains a list of all the panel software types and their current revisions. The software type in bold and colored green indicates that its more recent version can be loaded on the panel.

Note: The System Upgrade screen is launched by default when the USB key is inserted in the USB Port of the 4007 CPU Card.

• Use the Select All button to select all of the software types listed in the table.

• Use the Change Job button to load a new job on the panel.

• Use the Refresh Reset button to refresh the software type list.

• Use the Process Upgrade button to proceed with the change.

SystemUpgrade

Mass Storage

Job Backup

SaveReports

UpgradeStatus

SnapShotRecovery

Eject USB

SelectAll

System Upgrade

Change Job

RefreshReset

ProcessUpgrade 0 of 10 files selected

CARD SOFTWARE TYPE REVISION

0

0

0

0

0

4007H1LN

Main App

Bootloader

Kernel

Filesystem

1

302.03.02.02

1.00.00.14

1.00.00.11

1.00.00.20

Panel Setup, Continued

20


Alarm Log Overview: The Alarm Log screen contains a list of alarms that the panel has received. Refer to Figure 6 for access levels required for each option inside the Alarm Log screen.

Screen Buttons:

Scroll Up Scroll down Return

Figure 9. Alarm Log Screen

FIRE ALARM IN SYSTEM

Menu

DateTime

First of 1 M1-30-0 Date Time

M1-30-0PULL STATION FIRE ALARM

AlarmFunctions

ACK1

Clear:

IMPORTANT: Use the Clear button only after the alarms have been investigated.

Tap the Clear button to erase all entries in the Alarm Logs screen.

Clear

Alarm Log

21


Trouble Log Overview: The Trouble Log screen contains a list of Troubles that the panel has received. Refer to Figure 6 for access levels required for each option inside the Trouble Log screen.

Screen Buttons:

Scroll Up Scroll down Return

Figure 10. Trouble Log Screen

TROUBLE IN SYSTEM

Menu

DateTime

First of 1 M1-17-0 Date Time

M1-17-0SUPPRESSION DETECTOR HEAD MISSING

AlarmFunctions

ACK1

Clear:

IMPORTANT: Use the Clear button only after the Troubles have been investigated.

Tap the Clear button to erase all entries in the Trouble Logs screen.

Clear

Trouble Log

22


Search Overview: Use the Search screen to look for configured points under panel control. Refer to Figure 6 for access levels required for each option inside the Search screen.

Screen Buttons:

Scroll Up Scroll down Accept Return Erase

Figure 11. Search Screen

Search

New Search

COMMON TROUBLE POINT FORNODE: 4

DateTime

1

ZN1 ZN1

ZN2 ZN2

ZN3 ZN3

New Search: Search for a Specific Point:

The point search keypad opens automatically when the Search screen is accessed or by pressing the New Search button.

1. Select the desired point type. For example, to select an IDNet point, press on the IDNet button.

2. Select the desired point number. For example, to select an IDNet point M1-1-0, enter “1-1-0”.

Note: Point numbers are first generated when the ES Panel Programmer is used to program points into the panel.

3. Tap the Accept button to execute the search. Tap the Erase button to erase the last character entered. Use the Return button to return to the Search screen.

Browse the List of Configured Points

1. If opened, close the keypad by pressing anywhere outside the keypad. You will see a list of all the points configured on the network.

2. Use the Scroll Up and Scroll Down buttons to navigate the list, the Accept button to get more details on a point, and the Return button to return to the System Menu screen.

AUXZONE SIG

FB IO IDNet

Pseudo Analog LIST

ADDR

New Search

31 2

4 5 6

7 8 9

0

M1-1-0

.

IDNet

Search

23


Diagnostics Overview: Use the Diagnostics function to run tests on the panel and the devices. Refer to Figure 6 for access levels required for each option inside the Diagnostics screen.

Screen Buttons:


Figure 12. Diagnostics Screen

Diagnostics Menu

HW Reset Restart WalkTest USER BUTTON 1

USER BUTTON 2

USER BUTTON 3

Piezo Silence

CfigDownload

Next Page

Earth Fault Search

Earth Fault Latch

Date Time

NAC Miswire Test

Diagnostics MenuDuplicate

Device SearchWeak Answer

SearchTrueAlert

TestTrueAlert NAC Test

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

CO Algorithms

Install Mode

Previous Page

DateTime

Net Diag

HW Reset:

Tap the Hardware Reset button to re-initialize the state of certain hardware components. A hardware reset is typically used to reset a Class A Trouble after the problem causing the Trouble is resolved.

Note: If you attempt to perform a hardware reset without first fixing the problem causing the Trouble, the hardware reset fails and the Trouble re-appears.

Restart:

Tap the Restart button to restart the panel by Warm Start or Cold Start:

• Warm Start: Preserves the logs and the disabled status of any points that are in disabled state.

• Cold Start: Clears all history logs and re-enables any points that were previously disabled.

WalkTest:

Tap the WalkTest button to open the WalkTest Settings screen, which contains Walktest groups configured by technicians for use during maintenance testing. The following functions are available:

• Tap the Next Group button to select the next WalkTest group.

• Tap the Prev Group button to select the previous WalkTest group.

• With an item in the WalkTest group selected, tap the Select Item button to open a new screen where information and additional functions for that item are available.


Restart Menu

WarmStart ColdStart USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

WalkTest Settings

Next Group

Prev Group

Select Item

Walktest Group Information

Date Time

Diagnostics

24


Piezo Silence:

Tap the Piezo Silence button to access the Piezo Silence Menu screen, where the On or Off buttons can be used to control the piezos at the panel and turn the Remote Annunciator’s piezo on or off.

Cfig Download:

Tap the Cfig Download button to access the Configuration Menu screen. Inside, the following functions are available:

1. Tap the Enable button to allow a job download to a remote panel.

2. Tap the Enable All button to allow a job download to all the remote panels.

3. Tap the Disable button to disable the option of a job download to a remote panel.

4. Tap the Revert button to access the following functions:

• Alt Cfig: Tap this button to see the details of the last job used by the panel.

• Swap: Tap this button to swap the current job for the one used by the panel last.

• NoSwap: Tap this button to move back to the Configuration Menu screen.

Earth Fault Search:

Tap the Earth Fault Search button to access the Earth Fault Search? screen, which can be used to test for earth faults in the circuit. The following functions are available:

• Press the Location button to display a list of cards that can be tested for earth faults.

• Press the IDNet button to display a list of IDNet channels that can be tested for earth faults.

• Press the LastResults button to view the results of the last earth fault test.


Piezo Silence Menu

Off On USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Configuration Menu

Enable Enable All USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

Disable Revert

DateTime

Earth Fault Search?

Location IDNet USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

LastResult

DateTime

Diagnostics, Continued

25


Earth Fault Latch:

Tap the Earth Fault Latch button to access the Earth Latch Menu screen, which can be used to latch intermittent earth fault Troubles to the panel. This allows the panel to consistently display a Trouble instead of each time it re-occurs. The following functions are available:

• Tap the Off button to disable the Earth Latch function.

• Tap the On button to enable the Earth Latch function.

• Tap the ViewRaw button to view the locations of the raw earth faults.

NAC Miswire Test:

Tap the NAC Miswire Test button to access the NAC Test Menu screen, which can be used to perform a wiring test on the Notifications Appliance Circuits (NAC). The following functions are available:

• Tap the All button to test all the NACs at once.

• Tap the Single button to test each NAC separately.

Duplicate Device Search:

Tap the Duplicate Device Search button to access the Duplicate Dev Menu screen, where On or Off buttons can be used to turn the detection of duplicate devices on IDNet channels on or off.

Weak Answer Search:

Tap the Weak Answer Search button to access the Weak Answer Menu screen, where the On or Off buttons can be used to turn the detection of weak answering devices on IDNet channels on or off.


Earth Latch Menu

Off On USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

ViewRaw

DateTime

NAC Test Menu

All Single USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

Duplicate Dev Menu

Off On USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

Weak Answer MenuOff On USER

BUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime


26


TrueAlert Test:

Tap the TrueAlert Test button to access the TrueAlert Tests Menu screen, where tests for TrueAlert addressable notification appliances can be performed. The following functions are available:

• Tap the TrueAlert ES Self-Test? button, and then use the Run Self-Test? button to run Self-Test, or use the View Test Results? button to view the results for TrueAlert appliances.

• Tap the TrueAlert Device LEDs Test? button, and then use the On or Off buttons to turn the TrueAlert appliance LEDs on or off.

• Tap on the TrueAlert Device Test Mode? button, and then use the On or Off buttons to place the TrueAlert appliances in or out of Test Mode.

• Tap the TrueAlert Silent Test Mode? button, and then use the On or Off buttons to choose whether you want to place the TrueAlert appliances in Silent Test Mode or not. In Silent Test Mode, the device’s sounders are disabled.

TrueAlert NAC Test:

Tap the TrueAlert NAC button to perform a TrueNAC Voltage Drop Test. This test ensures that 4906 devices are installed properly by determining the line voltage for compatible notification appliances that are connected to a TrueAlert Power Supply (TPS) Signaling Line Circuit (SLC), under worst-case panel operating conditions. After pressing the TRUENAC button, the following options are available:

• All: Press this button to test all the TPS SLC lines at once. After pressing this button, these options become available:

- HornON: Press this button to set the horns to high volume during the test.

- HornOFF: Press this button for a silent system test.

• Single: Press this button to test each TPS SLC line separately.

Notes: 1. The results of the TrueNAC Voltage Drop Test are displayed on the screen. A Trouble condition is generated for every device that has failed the test.

2. If Horns are on, the panel will perform two passes: one with horns on and one with horns off. This is done to enhance the accuracy of A/Vs measurement.

CO Algorithms:

Tap the CO Algorithms button to access the IDNet CO Algorithms Menu screen. The following functions are available:

• Tap the Off button to disable the IDNet CO Algorithms. This is useful when smoke testing the IDNet CO devices.

• Tap the On button to enable the IDNet CO Algorithms.


TrueAlert Tests Menu

TrueAlert ES Self-Test?

USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

TrueAlert Device LEDs

Test?

TrueAlert Device Test

Mode?

TrueAlert Silent Test Mode?

DateTime

TrueAlert NAC Test Menu

All Single USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime

IDNet CO Algorithms Menu

Off On USERBUTTON 1

USERBUTTON 2

USERBUTTON 3

DateTime


27


Install Mode:

Install Mode is a feature that minimizes the number of Troublesthat occur when the system is being installed or is undergoing extensive service, by placing points and cards that can cause Troubles in Install Mode during those times. Install Mode raises a single “INSTALL MODE ACTIVE” Trouble, regardless of the number of items in it.

Tap the Install button to access the Install Mode Menu screen. The following functions are available:

• Tap the IViewMod button to view all the items in Install Mode.

• Tap the IAddMiss button to add items to Install Mode.

• Tap the IAddOpens button to add all open circuits to Install Mode.

• Tap the IRemvNorm button to remove an item from Install Mode.

• Tap the IRemvAll button to remove all the items from Install Mode.

Install Mode Menu

IViewModUSER

BUTTON 1

USERBUTTON 2

USERBUTTON 3

IAddMiss IAddOpens IRemvNorm

IRemvAll

DateTime

NetDiag:

Tap the NetDiag button to access the Net Diagnostics Menu screen, where the following functions for analyzing and gathering network

information are available. Navigate to each option by using the and

buttons. To select an option tap the Select Item button when it is highlighted.

• Diagnostics by Node: Use this option to choose a node and display its details.

• Net Diag Logging: Use this option to choose which network parameters to log, and where these logs are saved.

• Network Tallies: Use this option to choose whether to view or clear network tallies.

• Diag Tbls Missing Node Troubles: Use this option to enable or disable missing node Troubles.

• Diagnostic Message Options: Use this option to select the node to which diagnostic messages are sent, the message directions, and the number of message retries.

• Relay Mode: Use this option to choose whether or not the current node is in Relay Mode.

• Repeater/Reset for All Nodes: Use this option to reset/restore nodes, or to put the nodes in Repeater Mode.

• Current Details of Network: Use this option to obtain information on the number of nodes configured, communicating and in Repeater Mode, as well as the Monitor node, Left End node, Right End node, and the node’s Repeater source. Use this option to also determine the network topology, attendance, and the node IDs.

• Stop ALL Net Diag Functions: Use this option to stop all the network diagnostic functions that are currently running.

Net Diagnostics Menu

SelectItem

DateTime

Network Diagnostics are not ActiveThis node is ONLINENetwork is Running in style 7

Diagnostics by NodeNet Diag LoggingNetwork TalliesDiag Tbls Missing Node TroublesDiagnostic Message optionsRelay ModeRepeater/Reset for all NodesCurrent details of networkStop ALL Net Diag Functions


28


Report Menu Overview: Press the Report Menu button to access the Report Menu screen, where various types of reports on the system points can be generated. To generate a report:

1. Press the Report Menu button from the Main Menu screen to open the Report Menu screen (Figure 13).

2. A report can either be saved to a USB key or printed. See instructions below for both options:

Printing a Report Saving a Report to a USB Key

1. Press the Options button and then press Select to choose a printer.

2. In the Report Menu screen, press a report button to print the report.

1. Insert the USB key inside the USB Port of the 4007ES CPU Card.

2. Press a report button to save the report to the USB key.

Note: Pressing a report button without first inserting a USB key or choosing a printer generates an error message stating that hardware could not be found.

Refer to Figure 6 for access levels required to use each option inside the Report Menu screen.

Screen Buttons:

Scroll Up Scroll Down Return

Figure 13. Report Menu Screen

Report Menu

AlarmLog TroubleLog TrueAlarmStatus

TrueAlarm Service

USER BUTTON 1

USER BUTTON 2

USER BUTTON 3

TrueAlert NAC Test

TrueAlert Status TrueAlarm CO Active List

Verification Tally TrueAlert Self-Test

Date Time

Options

Alarm Log:

Tap the AlarmLog button to generate a report containing the list of alarms that the panel has received.

Trouble Log:

Tap the TroubleLog button to generate a report containing the list of Troubles that the panel has received.

TrueAlarm Status:

Tap the TrueAlarm Status button to generate a report containing the status of the various TrueAlarm devices connected to the panel. The report includes the following information:

• Device Number

• Custom Label

• Current Sensitivity of the Point

• Point Status: Normal, Trouble, Alarm

• Almost Dirty Status: Points that are almost dirty have an asterisk.


Report Menu

29


TrueAlarm Service:

Tap the TrueAlarm Service button to generate a report which contains the following information:

• Device Number

• Custom Label

• Alarm Level (sensitivity level of the device)

• Average Value

• Current Value

• Percent of Alarm: Shows the current value for the sensor. Value is shown as a percentage of 100% (alarm). For example, if the value shown is 9%, it means that the sensor is currently at 9% of the value required to trigger an alarm.

• Peak Value: Shows the highest value that the sensor has reached. Value is shown as a percentage of 100% (alarm). For example, if the value shown is 9%, it means that the peak value experienced by the sensor was 9% of the value required to trigger an alarm.

• Current State: Possible values include Normal, Trouble, Dirty, Excessively Dirty, and Almost Dirty.

TrueAlert NAC Test:

Tap the TrueAlert NAC Test button to generate a report which contains the following information for each TrueAlert device:

• Point ID

• Custom Label

• Device Type

• Candela

TrueAlert Status:

The TrueAlert Status Report can be created after the TrueNAC Voltage Drop Test is run.

Tap the TrueAlert Status button to access the Print TAlert Status screen. The All button can be used to generate the report containing the status for all devices. The Last button can be used to generate a report containing the status of the last test. The report contains the following information:

• Point ID

• Custom Label

• Pass/Fail

TrueAlarm CO:

Tap the TrueAlarm CO button to generate a report with the following information regarding the TrueAlarm CO devices:

• Device Number (on the network)

• Custom Label (custom description of the device)

• Current Device Value (PPM)

• End-of-Life Date

• Device Status (Normal, Trouble)


Report Menu, Continued

30


Active List:

Tap the Active List button to access the Print Active List screen, where the Install Mode button can be used to generate a report containing the following Install Mode list information:

• Point ID

• Custom Label

• Device Status

Verification Tally:

Tap the Verification Tally button to generate a report containing the following information for each device supporting the alarm verification:

• Device Number

• Custom Label

• Device Type

• Point Type

• Tally Count

TrueAlert Self-Test:

Tap the TrueAlert Self-Test button to access the Print TA Self-Test screen to generate a report containing the Self-Test results for the TrueAlert appliances. Tap the ALL button to generate a report with the results for all appliances. Tap the LAST button to generate a report with result for the last device.

Report Menu, Continued

31

4007ES Operator’s Manual (579-1165)Index

AAccess Level Logout ....................................................................................................................................................... 14Active List ........................................................................................................................................................................ 30Alarm Acknowledgement ................................................................................................................................................... 6Alarm Condition Details ..................................................................................................................................................... 9Alarm Condition Recognition ............................................................................................................................................. 5Alarm Conditions ............................................................................................................................................................... 5Alarm Global Acknowledge ............................................................................................................................................... 6Alarm Individual Acknowledge ........................................................................................................................................... 6Alarm Log ..................................................................................................................................................................20, 28Alarm Processing .............................................................................................................................................................. 6Alarm Silence .................................................................................................................................................................... 7Alarm Silence LED ............................................................................................................................................................ 4Alarm Tally ....................................................................................................................................................................... 30Alt Cfig ............................................................................................................................................................................. 24

BBi-color User-Defined LEDs .............................................................................................................................................. 4

CCard Revision Information ............................................................................................................................................... 16Card Status Information ................................................................................................................................................... 16Cfig Download ................................................................................................................................................................. 24Change Job ..................................................................................................................................................................... 19Clear ................................................................................................................................................................................ 20Clear Alarm Log ............................................................................................................................................................... 20Clear Trouble Log ............................................................................................................................................................ 21CO Algorithms ................................................................................................................................................................. 26Cold Start ......................................................................................................................................................................... 23Color Touchscreen LCD Annunciators .............................................................................................................................. 3

DDiagnostics ...................................................................................................................................................................... 23Duplicate Device .............................................................................................................................................................. 25

EEarth Fault Latch ............................................................................................................................................................. 25Earth Fault Search ........................................................................................................................................................... 24Eject USB ........................................................................................................................................................................ 19

FFire LED ............................................................................................................................................................................ 4

HHardware Reset .........................................................................................................................................................13, 23

IInstall Mode ..................................................................................................................................................................... 27Introduction ........................................................................................................................................................................ 3IP Info .............................................................................................................................................................................. 17

JJob Backup ...................................................................................................................................................................... 19

LLamp Test ........................................................................................................................................................................ 13Launching a New Search ................................................................................................................................................ 22List of Configured Points ................................................................................................................................................. 22

32


MMain Menu ....................................................................................................................................................................... 13Mass Storage .................................................................................................................................................................. 19

NNACTest .......................................................................................................................................................................... 25NetDiag ............................................................................................................................................................................ 27New Search ..................................................................................................................................................................... 22NoSwap ........................................................................................................................................................................... 24

PPanel Serial Number ....................................................................................................................................................... 16Panel Setup ..................................................................................................................................................................... 18Piezo .................................................................................................................................................................................. 4Piezo Silence ................................................................................................................................................................... 24Power LED ........................................................................................................................................................................ 4Priority 2 Global Acknowledge ........................................................................................................................................... 6Priority 2 Individual Acknowledge ...................................................................................................................................... 6Priority 2 LED .................................................................................................................................................................... 4Process Upgrade ............................................................................................................................................................. 19

RRefresh Reset .................................................................................................................................................................. 19Report Menu .................................................................................................................................................................... 28Restarting the Panel ........................................................................................................................................................ 23

SSave Reports ................................................................................................................................................................... 19Search ............................................................................................................................................................................. 22Search for a Specific Point .............................................................................................................................................. 22Select All .......................................................................................................................................................................... 19Set Time/Date .................................................................................................................................................................. 18Show Alternate Config Version ........................................................................................................................................ 18Slide-in Labels ................................................................................................................................................................... 4SnapShot Recovery ......................................................................................................................................................... 19Software Revision Information ......................................................................................................................................... 16Supervisory and Trouble Condition Processing .............................................................................................................. 11Supervisory and Trouble Condition Recognition ............................................................................................................. 10Supervisory and Trouble Conditions ............................................................................................................................... 10Supervisory and Trouble Conditions Details ................................................................................................................... 12Supervisory Global Acknowledge .................................................................................................................................... 11Supervisory Individual Acknowledge ............................................................................................................................... 11Supervisory LED ................................................................................................................................................................ 4Swap ................................................................................................................................................................................ 24Swap Config .................................................................................................................................................................... 18System Files Info ............................................................................................................................................................. 17System Info ...................................................................................................................................................................... 16System Reset ..............................................................................................................................................................8, 13System Upgrade .............................................................................................................................................................. 19

TTouchscreen ...................................................................................................................................................................... 4Touchscreen Calibration .................................................................................................................................................. 18Trouble Global Acknowledge ........................................................................................................................................... 11Trouble Individual Acknowledge ...................................................................................................................................... 11Trouble LED ...................................................................................................................................................................... 4Trouble Log ...............................................................................................................................................................21, 28TrueAlarm CO Devices .................................................................................................................................................... 29TrueAlarm Device Status ................................................................................................................................................. 28

Index, Continued

33


TrueAlarm Service Report ............................................................................................................................................... 29TrueAlert Device Information ........................................................................................................................................... 29TrueAlert Device Status ................................................................................................................................................... 29TrueAlert Self-Test .......................................................................................................................................................... 30TrueAlert Test .................................................................................................................................................................. 26TRUENAC ....................................................................................................................................................................... 26

UUpgrade Status ................................................................................................................................................................ 19Use Alternate Config Version .......................................................................................................................................... 18User Access Level ........................................................................................................................................................... 14User Access Level Chart ................................................................................................................................................. 15User Interface .................................................................................................................................................................... 4

WWalktest ........................................................................................................................................................................... 23Warm Start ...................................................................................................................................................................... 23WeakAnswer ................................................................................................................................................................... 25

Index, Continued

579-1165

Rev. CR

4007ES Operator’s Manual - Interamsa | Distribuidor Autorizado de … · 2017. 10. 12. · 4007ES...

Documents

Transcript of 4007ES Operator’s Manual - Interamsa | Distribuidor Autorizado de … · 2017. 10. 12. · 4007ES...