4. Z-axis assembly - Amazon Web Services...Step 3 — Screw Z-axis-bottom parts to the frame Place...
Transcript of 4. Z-axis assembly - Amazon Web Services...Step 3 — Screw Z-axis-bottom parts to the frame Place...
4. Z-axis assemblyWritten By: Josef Prusa
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 1 of 18
Step 1 — Get the necessary tools
13/17mm spanners
3.6mm flathead screwdriver
Needle-nose pliers
2.5 and 1.5mm Allen key
Step 2 — 3D printed parts
Z-axis-top-left
Z-axis-top-right
Z-axis-bottom-left
Z-axis-bottom-right
Z-screws covers
Use the hole for 8 mm smooth rodas orientation key in the next steps.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 2 of 18
Step 3 — Screw Z-axis-bottom parts to the frame
Place parts on the frame as shown in the picture.
Note the frame orientation (PRUSA logo has to be visible).
All screws in this step are M3x10 (6 pcs).
Use 2.5mm Allen key to tighten the parts to the frame.
Tighten them gently, no superhuman force required.
Note: If you have troubles tightening the screws, try to place them from the other side of the frameto clean the thread. Then place them again from the previous side. Proceed with caution, or youmight break the screw.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 3 of 18
Step 4 — Placing the Z-screw covers
Remove the trapezoid nuts from the motors.
Screw covers fully on both motor screws.
Covers should be screwed fully to the motor, but not too tight! The motor should keep spinningfreely.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 4 of 18
Step 5 — Placing the Z-motors
Place the Z motors on the frame.
Z motor left (labeled with Z axis left )
Z motor right (labeled with Z axis right )
Ensure the correct position of the motors (left/right).
Ensure the wires are not pinched between the motor and holder (see detailed photo).
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 5 of 18
Step 6 — Tighten the Z-motors
Use M3x10 screws (8 pcs) and M3w washers (8 pcs).
Use 2.5mm Allen key to tighten the motor to the printed part.
Step 7 — Placing trapezoid motor nuts
Insert M3 nuts (4 pcs) in the printed parts as shown in the picture.
Nuts orientation does not matter.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 6 of 18
Step 8 — Tighten trapezoid motor nuts
Use M3x12 screws (4 pcs) to tighten nuts in place.
Use 2.5mm hex spanner to tighten the screws.
Step 9 — Identifying rod length
In the following steps, use theshortest rods (320 mm).
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 7 of 18
Step 10 — Preparing the Z-rods
Insert Z-rods (the shortest ones) inside the Z-axis-bottom parts.
Step 11 — Assembling the X-axis
Carefully slide X-axis on rods and trapezoid screws. By rotating both screws simultaneously let X-axis to slide until both trapezoid screws are exposed as in the picture.
Insert X-axis very carefully, perfectly in axis with the bearings and with minimal force.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 8 of 18
Step 12 — Placing the Z-axis-top parts
Place parts on the frame as in the picture.
Use 2.5mm hex spanner to tighten the parts to the frame.
Check both leadscrews in the upper part of printer, they shouldn't touch the edges of printed part.If so, release the motor holder at the bottom and slightly move it.
All screws in this step are M3x10 (4 pcs).
Step 13 — Cable management
Insert the zipties in the holes at the bottom of the frame.
Tie the cables to the frame as shown in the picture.
Note that the left Z-motor cables are tied with the last ziptie.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 9 of 18
Step 14 — Cleaning up
Use pliers and cut the excess ziptie.
Note the position of the connectingziptie.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 10 of 18
Step 15 — Assembling the Y-axis
Grab the Y-axis assembly in your hand and slide it into the frame. You should be able lift theconstructed printer as a whole.
Tighten the M10n nuts to the frame.
Ensure that there is a washer between a nut and the frame on both sides.
Ensure the correct orientation of the Y-axis assembly and the frame (longer part should be on theside with motors).
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 11 of 18
Step 16 — Assembling the X-axis belt part 1
Insert the flat part of X-GT2 belt (longer one) into the X-carriage as in the picture.
A reference video is included at step 25 covering steps 16-24.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 12 of 18
Step 17 — Assembling the X-axis belt part 2
Guide the belt around the pin as shown in the picture.
Insert the belt all the way into the belt holder as shown in the picture.
Note that there is no belt going out of the X-carriage, it's IMPORTANT.
Step 18 — X-axis belt idler guide
Guide the X-axis belt through X-end-idler, around the 623h bearing with the housing and back.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 13 of 18
Step 19 — X-axis belt carriage guide
Guide the X-axis belt through the X-carriage.
Step 20 — X-axis belt motor guide
Guide the X-axis belt through the X-end-motor, around GT2-16 pulley and back.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 14 of 18
Step 21 — Loosening the motor
Remove the M3x18 screws.
Rotate the motor counter-clockwise as shown in the picture.
This step is illustrative, you don't need to remove the frame.
Step 22 — Tightening the X-axis belt part 1
Use pliers to tighten up the X-axisbelt.
Insert the flat part of belt as shownin the picture.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 15 of 18
Step 23 — Tightening the X-axis belt part 2
Guide the belt around the pin as shown in the picture.
Push the belt all the way into the X-carriage.
The belt shouldn't be tight at the moment.
Step 24 — Tensioning the belt
Rotate the motor back
Screw in the removed M3x18screws
If you have to apply too much forceand are experiencing troubles, rotatethe motor back, repeat previous stepwhile making the belt more loose.
The belt should be quite tight, itshould 'ping' like a music string.
This step is illustrative, you don'tneed to remove the frame.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 16 of 18
Step 25 — VIDEO for steps 16-24
Insert the flat part of X-GT2 belt(longer one) into the X-carriage,around the pin. Guide the X-axis beltthrough X-end-idler, around the623h bearing with the housing andback. Guide the X-axis belt throughthe X-carriage. Guide the X-axis beltthrough the X-end-motor, aroundGT2-16 pulley and back.
Remove the two M3x18 screws.Rotate the motor counter-clockwise.
Insert the flat part of the belt aroundthe pin.
Rotate the motor back. Screw in theremoved M3x18 screws.
Video is available in an online(digital) version only.
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 17 of 18
Step 26 — Adjusting tension screws
Gently tighten both screws untilslight force is applied on bothsmooth rods.
Step 27 — All done!
Congratulations! You've justassembled the Z-axis.
You can continue by assembling theExtruder in the next chapter - 5.Extruder Assembly
4. Z-axis assembly Draft: 2017-06-24Guide ID: 106 -
This document was generated on 2020-04-26 09:45:33 AM (MST).
© 2020 prusa3d.dozuki.com/ Page 18 of 18