3M Water Filtration - FJ Developmentfjdevelopment.com/9246/Taco Bell Cut Sheets/P-315... · 400...

The 3M™ Water Filtration Products FSTM-075 Reverse Osmosis system producesconsistent water quality water for the reduction of scale and corrosion-causing minerals in flash steamer applications. The RO membrane rejects over 96% of the minerals that cause scale build-up and corrosion. Activated carbon and graded density pretreatment helps protect the RO membrane from chlorine and fine sediment.

FSTM-075

FSTM-075FlashGard HP™ Reverse Osmosis System

SPEC#

QUANTITY

PRODUCT SPECIFICATIONS

PRODUCT BENEFITS

model: Flash Steamer Equipmentapplication:

Application

Flash Steamers

Capacity*

75 gpd (284 lpd)

ReductionClaims

Reverse Osmosis System

PartNumber

56123-06FSTM-075

ModelNumber

* Capacity is at 77° F (25°C) to atmosphere** Minimum 60 psi (414kPa) feedwater pressure required.

• Sanitary Quick Change (SQC) encapsulated filter and membrane design reduces the possibility of contamination during change-outs.

• Patented cartridge interconnect system allows for quick and easy cartridge change-outs. No spills, no mess.

• Line pressure reverse osmosis membrane requires no power; operates on incoming water pressure**.

• Rugged stainless steel bracket design is virtually rust and corrosion resistant; allows system to either be wall-mounted or set on a shelf.

• Compact design allows for installation in tight areas.

• FDA CFR-21 and/or NSF compliant materials provide peace of mind that this system is suitable for foodservice applications.

3M™ Water Filtration

P-315

`

PHYSICAL

LITFS348 0208

CUNO Incorporated 400 Research Parkway

Meriden, CT 06450, USAToll Free: 1.888.218.CUNOWorldwide: 203.237.5541

Fax: 203.238.8701www.cunofoodservice.com

a 3M company

Part Number TypeQuantityRequired

55706- 08 5 Micron Prefilter Cartridge 1

55987- 16 Reverse Osmosis Membrane 1

9 5/16"(23.7 cm)

12 3/16"(31 cm)

15 7/8"(40.3 cm)

IMPORTANT: INSTALLATION TIPS

REPLACEMENT CARTRIDGES

LIMITED WARRANTY

PHYSICAL SPECIFICATIONS

SPEC #

QUANTITY

MODEL NUMBER

PART NUMBER

© 2008 3M Company. All rights reserved.3M and CUNO are trademarks of 3M Company used under license.

• System incorporates reverse osmosis technology.• System contains integrated prefiltration for the reduction of sediment and chlorine taste and odor.• RO membrane is thin film composite (TFC) type.• System provides greater than 96% rejection of TDS.• System manufactured of FDA/CFR-21 compliant materials.• System is wall mountable with a stainless steel bracket design.• System inlet plumbing connections are 1/4” quick disconnect type.• System drain plumbing connections are 1/4” quick disconnect type.• System outlet plumbing connections are 3/8” quick disconnect type.• System includes an integrated 2 gallon(7.6 liter) water storage tank.• System production rate 75 gallons (284 liters) at 77°F (25°C) per 24 hour period.• Incoming water pressure must be a minimum of 60 psi (414 kPa)

and a maximum of 100 psi (690 kPa). • Incoming water temperature must be a minimum of 40° F (4.4° C)

and a maximum of 100° F (37.8° C).

FSTM-075FlashGard HP™Reverse Osmosis System 3M™ Water Filtration Products

WARNING: To reduce the risk associated with the ingestion of contaminants:• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. EPA Establishment #070595-CT-001

CUNO Incorporated recommends regularly scheduled maintenance and replacement of the filter cartridge(s) in order for the product to perform as advertised/sold. CUNO shall not be liable for system failures due to improper maintenance.

These installation tips are for informational purposes only and are not in-tended to be used as actual installation instructions.CAUTION: To reduce the risk associated with property damage due to water leakage:• Read and follow Use Instructions before installation and use of this system.• Installation and use MUST comply with all state and local plumbing codes.• Protect from freezing, remove filter cartridge when temperatures are expected to drop below 40°F (4.4°C).• Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 100°F (37.8°C).• Do not install if water pressure exceeds 100 psi (690 kPa). If your water pressure exceeds 125 psi (862 kPa), you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.

• Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.

• The disposable filter cartridge MUST be replaced every 12 months, at the rated capacity or if a noticeable reduction in flow rate occurs. • The RO membrane MUST be replaced every 24-36 months.

CUNO Incorporated warrants this Product (excluding disposable filter cartridge(s) and RO membrane cartridge(s)) to be free from defects in material and workmanship for two years from the date of purchase. The disposable cartridge is warranted from defects in material and workmanship for a period of one year from the date of purchase. The RO cartridge is warranted from defects in material and workmanship for a period of two years from the date of purchase. This warranty does not cover failures result-ing from abuse, misuse, alteration or damage not caused by CUNO or failure to follow installation and use instructions. If the Product is defective CUNO will replace the Product or refund your Product purchase price. CUNO will not be liable for any indirect, special, incidental, or consequential damages arising from the use of this Product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. To obtain warranty service, mail your request to Warranty Claims, CUNO Incorporated, 400 Research Parkway, Meriden, CT 06450. Proof of purchase (original sales receipt) must accompany the war-ranty claim, along with a complete description of the Product, model number and alleged defect. This warranty gives you specific legal rights and you may have other rights which vary from state to state, or country to country.

FSTM075 Installation Guide

For Taco Bell

© 2008 3M Company. All Rights Reserved.

FSTM075 Installation Summary

1. Unpack and inspect to confirm that all components

are present

2. Prepare area for installation and mount manifold

3. Install cartridges


3. Install cartridges

4. Complete line connections

5. Startup the new FSTM075 system

Start enjoying the benefits of your new water filtration system!

1 - Unpack the FSTM075 unit

� Check to see that all the FSTM075 installation parts

arrived with package

FSTM075 Parts List• Tank & bracket assembly


FSTM075 unit and installationkit parts

• Tank & bracket assembly• Pre-filter cartridge• Reverse Osmosis Membrane Cartridge• Water Sample Valve Assembly• 12” long 3/8” blue tubing• 10’ long ¼” red tubing• SFC red tubing (flow control)

2 - Mount the FSTM075 unit

� Select location to mount the FSTM075

unit. (FSTM075 dimensions: 12-1/4” W x

15-7/8” H x 9-3/8” D)

� Allow required clearance distance for the

inlet and outlet tubing connections

� Allow a required clearance distance of 3”


� Allow a required clearance distance of 3”

below the unit for replacement of

cartridges

� Mounting hardware (installer supplied)

for this unit needs to support a minimum

of 30 lbs to cover wet weight of unit 3” clearance

FSTM075 Installation Kit Diagram - Reference


Feed Water

3 - Install Cartridges

� Install Pre-Filter cartridge in front manifold head� Cartridge Installation Procedure: Remove red cap, insert into manifold head,

and turn ¼” turn to right until it stops into position

� Install RO membrane cartridge into back manifold

head as per RO membrane installation diagram� Remove plug from RO membrane cartridges drain fitting

� Insert into back manifold head



� Remove white plug from drain fitting

� Insert SFC tube into drain fitting

3 - Install Cartridges (Details)

� Install Pre-Filter cartridge in front manifold head� Cartridge Installation Procedure: Remove red cap, insert into manifold head,

and turn ¼” turn to right until it stops into position


Pre-Filter installation

3 - Install Cartridges (Details)

� Install RO membrane cartridges into back manifold

head as per RO membrane installation diagram� Remove plug from RO membrane cartridge drain fitting


� Insert SFC tube (flow control) into drain fitting

Important Step!


Remove plug Install RO ctg Install SFC tube

Important Step!

4 - Complete Line Connections

� Install installation parts on to FSTM075 unit, and close inlet

and water sample valves

� Connect inlet water supply to FSTM075 unit inlet

� Connect FSTM075 outlet to equipment feed water line



4 - Complete Line Connections (Details)

� Install installation parts on to FSTM075 unit, and

close inlet and water sample valves



� Connect inlet water supply to FSTM075 unit inlet


� Install outlet valve on water line (not supplied)


Inlet water supply connection

Outlet water supply connection


� Connect 1/4” tubing from FSTM075 to drain


Drain connection Drain

5 - Complete Startup Procedure

� Adjust tank air charge pressure� Locate schrader air valve on tank . Use a standard bicycle pressure gauge to read

the tank air pressure

� Adjust air pressure to account air pressure setting (see account setting slide)

� Open inlet water line



� Flush cartridges� Open outlet sample valve and run water to drain until a there is a steady flow of

water. Close sample valve.

� Open tank valve

� Open outlet valve

5 - Complete Startup Procedure (Details)

� Adjust tank air charge pressure� Locate schrader air valve on tank . Use a standard bicycle pressure gauge to read

the tank air pressure

� Adjust air pressure to account air pressure setting (see account setting slide)



Adjust tank air Open inlet water line


� Flush cartridges� Open outlet sample valve and run water to drain until a there is a steady flow

of water. Close sample valve.


Open/Close outlet sample valve


� Open tank valve

� Open outlet water line


Open outlet water lineOpen tank valve

FSTM075 Installation – Taco Bell Account Settings

� Water pressure into steamer – 20 to 30 psi

� Tank air charge pressure setting - 20 psi

� Install water regulator PN 62197-01 into water line


� Install water regulator PN 62197-01 into water line

*These settings above are required before installing the FSTM075 system.

3M Water Filtration - FJ Developmentfjdevelopment.com/9246/Taco Bell Cut Sheets/P-315... · 400...

Documents

Transcript of 3M Water Filtration - FJ Developmentfjdevelopment.com/9246/Taco Bell Cut Sheets/P-315... · 400...