3M Paradigm Temporization Material Tips for Success€¦ · 3M™ Paradigm™ Temporization...
2
3M ™ Paradigm ™ Temporization Material Tips for Success Fig. 2: Remove interproximal septa. Fig. 1: Remove excess material as needed. Fig. 4: Bleed a small amount of material through the mix tip before dispensing in the matrix. Discard extruded material. Fig. 3: Reposition matrix in the mouth to confirm proper fit. Fig. 14: Remove the excess. Fig. 6: Make sure to fill from the bottom up and to always keep the tip immersed in the temporary material to prevent voids. (Working time: 40 sec.) Fig. 5: Dispense material into the impression or matrix. Fig. 8: Check setting progress with excess material. Fig. 7: Seat in the mouth and hold firmly in place. Fig. 11: Remove oxygen inhibited layer with ethanol. Fig. 9: Remove from mouth between 1:40 and 2:50 (min:sec) from the onset of mixing. Fig. 10: Leave material in the matrix for 5:00 (min:sec). This is important to achieve a smooth and shiny surface. Fig. 13: Cement provisional restoration using a temporary cement. Fig. 12: Finish and polish as needed. DON’T FORGET TO: • Bleed cartridge before first use • Bleed tip before each use • Use only approved 3M ™ Mixing Tips • Adhere to working and setting times as detailed in the Instructions for Use • Following each use, use the mix tip as the cap for sealing cartridge during storage OPTIONAL !
Transcript of 3M Paradigm Temporization Material Tips for Success€¦ · 3M™ Paradigm™ Temporization...
3M™ Paradigm™ Temporization Material
Tips for Success
Fig. 2: Remove interproximal septa.Fig. 1: Remove excess material asneeded.
Fig. 4: Bleed a small amount of material through the mix tip beforedispensing in the matrix. Discard extruded material.
Fig. 3: Reposition matrix in the mouthto confirm proper fit.
Fig. 14: Remove the excess.
Fig. 6: Make sure to fill from thebottom up and to always keep the tip immersed in the temporary material to prevent voids. (Working time: 40 sec.)
Fig. 5: Dispense material into theimpression or matrix.
Fig. 8: Check setting progress withexcess material.
Fig. 7: Seat in the mouth and holdfirmly in place.
Fig. 11: Remove oxygen inhibited layerwith ethanol.
Fig. 9: Remove from mouth between1:40 and 2:50 (min:sec) from theonset of mixing.
Fig. 10: Leave material in the matrix for 5:00 (min:sec). This is important to achieve a smooth and shiny surface.
Fig. 13: Cement provisional restoration using a temporary cement.
Fig. 12: Finish and polish as needed.
DON’T FORGET TO:• Bleed cartridge before first use• Bleed tip before each use• Use only approved 3M™ Mixing Tips• Adhere to working and setting times as detailed in the
Instructions for Use• Following each use, use the mix tip as the cap for sealing
cartridge during storage
OPTIONAL
!
3M, Filtek, Garant, Paradigm and Protemp are trademarks of 3M or 3M Deutschland GmbH. Used under license in Canada. Please recycle. Printed in USA. © 3M 2017. All rights reserved. 70-2013-0860-1
www.3M.com/dental
3M Oral Care2510 Conway AvenueSt. Paul, MN 55144-1000 USA
Phone 1-800-634-2249Web 3M.com/dental
3M Canada Post Office Box 5757London, Ontario N6A 4T1 Canada
Phone 1-888-363-3685
3M Business Name3M Center, Building 220-12E-04St. Paul, MN 55144 USA
Phone 1-800-328-3908Fax 1-800-328-3909Email [email protected] mmm.com/areaofexpertise
Please recycle. Printed in USA © 3M 2015. All rights reserved. 70-0000-0000-0
Ventibus eveni sum. At litati cum fuga.
Sae comnis dolent volupta tectemo lorerit aturem restiaspiet volendis es eaquaspeles dit eumquosae prepernam, tet quam voluptatur re lamus audipsapero doluptae. Quatatempos sapitisserio ma ipit aborum eum aut ma volo molor autem nost, nes a ditatiis simodisquam quistrum facerro consentio mosam quaeseq uoditatio.
Uptatiam late rent aut aribusci ullori vernatur molupta consedion et pra nullaccabore sumquam laborro rehendi cum volupta ssinis aut accus sim solendiae magnim verovit voluptatur aspicto in culla qui omnis dipsandi ommo dus, quis quam harum estrum cone et es ima volut litate laborec uptions eratetus molor repudi simusam quassimod ut qui doloribus, omnisit earibearum et plabor assenim qui omniminusam ium et dollabo rerchitasi te voluptat res quo qui temqui ipsam exces nullut quo de alitiusdae sectota solo earum fugia im quassuscit, atiae perae sequia aut explic tempos iunt quam litae dolenim laut voluptas dolorest aciaestios et lam et dolendi auta verrum dunt que doluptur sinciata et doluptatur? Sanditame vita velest ea consequi reptae solo et inumque repratq uatusda.
Sae comnis dolent Volupta tectemo Sae comnis dolent Volupta tectemo
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456W 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
23456 56789 56897 23485
123456 23456 56789 56897
3M™ Paradigm™ Temporization Material... Innovative solutions for your temporary needs.
Shades match 3M™ Filtek™ Supreme Ultra Flowable RestorativesThree popular shades (A1, A2 and A3) match beautifully with global market leader Filtek Supreme Ultra Flowable restoratives.
A1A2
A3
Ordering InformationItem No. Product Information
3M™ Paradigm™ Temporization MaterialRefills46993 3M™ Paradigm™ Temporization Material Refill – A1
Includes: 1 cartridge – 50ml, A1; 16 cartridge mixing tips, blue; Instructions
46994 3M™ Paradigm™ Temporization Material Refill – A2Includes: 1 cartridge – 50ml, A2; 16 cartridge mixing tips, blue; Instructions
46995 3M™ Paradigm™ Temporization Material Refill – A3Includes: 1 cartridge – 50ml, A3; 16 cartridge mixing tips, blue; Instructions
Mix Tips71453 3M™ Garant™ Mixing Tips
Includes: 50 – Blue
3M™ Paradigm™ Temporization Material Refill – A1
3M™ Paradigm™ Temporization Material Refill – A2
3M™ Paradigm™ Temporization Material Refill – A3
