3M MISD Fixed & Folding Wall Mount Pre-Installation...

3M Mobile Interactive Solutions Division Tel: 1-800-328-1371 © 3M 2010. All Rights Reserved. www.3m.com/meetings 78-6971-1479-7 Rev. B (2/2010)

3M MISD

Fixed & Folding Wall Mount

Pre-Installation Packet

INDEX Pre-Installation Survey .............................................. 2 3M Standard Installation............................................ 7 Sample Installation Pictures ..................................... 9 Screen Size Chart..................................................... 11 Application Drawing................................................. 13 Annotation Sensor Kit ............................................. 14 Required Tools ......................................................... 15 Install Folding Wall Mount....................................... 17 Install Fixed Wall Mount .......................................... 28 Install I/O Module...................................................... 36 Installation Check List ............................................. 38 SCP Installation Notes & Tips ................................. 41

3M Mobile Interactive SolutionsTel: 1-800-328-1371 © 3M 2008 All Rights Reserved. www.3m.com/meetings 78-6971-1439-1 C (3/2009)

3M Mobile Interactive SolutionsPre-Installation Survey

E-Mail to: [email protected]

-or-

Fax to: 512-984-6550

Customer Name _______________________________________________

Title _______________________________________________

Company _______________________________________________

Address _______________________________________________

_______________________________________________

_______________________________________________

Phone ____________________________ E-Mail _____________________Product to be installed__________________________________ Quantity___________

Room SizeSmall <20 x 20 Medium >20 x 20 Large >40 x 40

Floor to Ceiling height ______________________

Wall Type (Yes) (No) Minimum ½” thick Dry Wall Metal Interior studs Wood Plank or Plywood Masonry, plaster or poured concrete Brick or Cinder Block Metal Glass Mobile Cart Other __________________________ Recessed Wall Installation Air Vent Vent Fan Sprinkler Heads

2 of 48

3M MISD Pre-Installation Survey

© 3M 2008. All Rights Reserved.

Lighting (Yes) (No) Fluorescent Spot Lighting Standard bulbs Lighting within 3 feet of unit Lighting Controls Dimmer switch On/.Off switch Security Devices Model ____________________________________ Mfg. _____________________________________ Window Location Rear wall Front wall Side wall Power OutletWithin 3 feet of screen center -OR- 6 feet of expected projector position? 120VAC 20Amp Dedicated (grounded line) ComputerWithin 6 feet of expected projector position? If not then location from projector in feet _________ Model ____________________________________ Mfg. _____________________________________ # of VGA ports ____________________________ #of USB ports _____________________________ DVD Player Model ____________________________________ Mfg. _____________________________________ VCR Player Model ____________________________________ Mfg. _____________________________________ Video Conferencing System Model ____________________________________ Mfg. _____________________________________ Printer Model ____________________________________ Mfg. _____________________________________

3 of 48



(Yes) (No)Audio System Model ____________________________________ Mfg. _____________________________________ A/V Controller Model ____________________________________ Mfg. ______________________________________ Other Model ____________________________________ Mfg. _____________________________________ Additional cables needed (Cables provided allow 2m (6 feet) of access – if longer cables are needed then additional fees apply) Power Cord VGA DVI-I RS232 RCA Audio RCA Video S-Video Component Video USB 3.5mm mini stereo audio Special Cable routing required? Through Ceiling? Across Floor? Along Wall? Special A/V Outlet Location ___________________________________ Type ______________________________________ Special Equipment KVM switch Distribution Amplifiers Select Type:

VGAS-Video Component Video

4 of 48



Other Electronic Devices in the room (Yes) (No) Watt saver (light controller) Door control Solid-state ballast controller Motion Detectors Remote IR controller Ultrasound device Other Annotation Devices Other ____________________________ If DMS or SCP product Whiteboard to be installed prior to this installation? Whiteboard to be installed as part of this task? (Note: additional fees apply) Existing chalkboard removed for additional fee

Please provide a brief description below of the way you intend to use the product such as presentations with on screen annotation, training and conference presentations, video conferences with presentations and on screen annotation, etc. Please include description of other devices in the room and any multi-screen applications used.

5 of 48


Room Layout Drawing Example:

Windows

Door

Light Controls Lights

3M Unit

Control Box (if applicable)

ComputerDVDPower

Outlet

Table Table

Table Table

Chairs

Please draw your room layout below including distances between equipment (photos may be sent via email or additional pages may be attached when required).

© 3M 2008. All Rights Reserved. 6 of 48



3M Standard InstallationBasic installation service includes:

Installation by authorized, licensed and insured professional. Delivery of your new Projection equipment Delivery of additional mounting hardware required to fit with your building construction Installation to the existing construction code in your areaConnect your new Projector to existing electrical outlets using standard cables Start up and test your new Projector to insure that it is working properlyClean up the installation site Remove and dispose of packaging materials Includes User Training via teleconference providing guidelines for proper use of your new projector, available at times scheduled by 3M during the month. Please contact 1-800-328-1371 for schedulingInformation on available enhanced service plans to provide trouble free warranty coverageLocations beyond 30 miles from city center may incur additional fees

Fixed Wall Mount installation includes:3M Wall Mount Bracket if required for your site Assembly and installation of the Projector, Fixed Wall Mount and Wall Mount Bracket. Connect customer equipment & check out unit functionality.

Folding Wall Mount installation includes:3M Wall Mount Bracket if required for your site Assembly and installation of the Projector, Folding Wall Mount, Wall Mount Bracket & other 3M components & accessories. Connect customer equipment & check out unit functionality.

Other ConsiderationsInstallation available 5 days a weekService days and hours may vary by market. Pending completion of the site assessment; additional terms, fees and restrictions may apply.Some installations may require an on-site visit at additional cost to verify site conditions.On site training can be arranged at an additional cost. Enhanced warranties are available at an additional cost.

NOTE: Installation and set up of additional equipment is available but not included. Please contact our Call Center at 1-800-328-1371 for additional quotation. Customer supplied or other manufacturer's equipment installed is protected under their individual product warranties thus failures requiring their replacement may incur an additional fee.

Some localities require seismic evaluation certification per applicable Engineering requirements. If this is required by the project engineer, program manager, site engineer, or architect then please contact us at 1-800-328-1371 for available evaluations defining the recommendations.

7 of 48


Warranty3M warrants that when the 3M Product is used according to 3M’s Intended Use Statement (www.3M.com/meetings), it will perform satisfactorily for the warranted durability period as stated in the applicable 3M Product Manual in effect at the time of purchase. The warranties stated in the applicable 3M Product Manuals are exclusive and are made in place of any and all express or implied warranties or conditions, including any implied warranty of merchantability or fitness for a particular purpose, or any industry practice or custom or trade usage. Failure to follow the instructions contained in the appropriate 3M Product Manual or to use the 3M Product in accordance with 3M’s Intended Use Statement, will void all warranties and limited remedies. EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT. This limitation applies regardless of the legal theory upon which damages are sought. If 3M Product is defective within the applicable warranty period, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the 3M Product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the product with the same or equivalent model and with a new or refurbished product. In the case of an approved warranty claim, the replacement 3M Product will carry only the remaining term of the original 3M Product’s warranty period as stated in the applicable 3M Product Manual. For warranty service, you must provide proof of the date of the original purchase, otherwise the manufacturing code date will be used to establish the start date of the warranty.3M Product Manuals include durability statements and may include limitations specific to the product(s) being used or its intended applications, which take precedence over any statement made here. Warranty terms, limitations and exclusions may differ outside the United States of America.

I have read and understand

Signature Date

© 3M 2008. All Rights Reserved. 8 of 48

Completed Installation Sample#1

Note: In above example, wires are secured using optional (customer supplied) channel run molding. 3M standard installation provides adhesive backed wire tie wraps to secure wires.

Optional channel run molding used to secure wires.

9 of 48

Completed Installation Sample#2

Note: In above example, wires are secured using optional (customer supplied) channel run molding. 3M standard installation provides adhesive backed wire tie wraps to secure wires.

Optional channel run molding used to secure wires.

10 of 48

3M™ SCP Screen Size Chart

SCPV1 SCPV2

Projector Model Min. Image Size, Diagonal

Max. Image Size, Diagonal

Min. Image Size, Diagonal

Max. Image Size, Diagonal

SCP712

57.78"(1468 mm)

83.84"(2130 mm)

63.84"(1622 mm)

95.96"(2437 mm)

SCP715/717

47.26"(1200 mm)

Not Recommended

70.97"(1803 mm)

Not Recommended

52.78"(1341 mm)

82.00"(2083 mm)

SCP716

52.73"(1339 mm)

78.79"(2001 mm)

58.79"(1493 mm)

90.91"(2309 mm)

SCP740

43.50"(1105 mm)

Not Recommended

65.33"(1659 mm)

Not Recommended

48.58"(1234 mm)

75.48"(1917 mm)

SCPV1 SCPV2

Fixed Wall Mount for SCP Products 78-6969-9936-2 78-6969-9986-7

Folding Wall Mount for SCP Products 78-6969-9950-3 78-6969-9987-5

Folding Wall Mount with Speakers (2 20-watt speakers) for SCP Products 78-6969-9938-8 78-6969-9988-3

3M Projection Systems products are sold through a network of fully-trained distributors. Contact one of our full-line dealers to

place orders. To find a full-line dealer please visit: www.3m.com/meetings and select ‘Locate a Servicing or Selling Dealer’.

11 of 48

Projection Systems3M Austin Center6801 River Place Blvd.Austin, TX 78726-9000866-631-1656www.3M.com/meetingse-mail: [email protected]

3M is a trademark of 3M Company.

Please Recycle. Printed in USA.© 3M 2009. All Rights Reserved.78-6971-1466-4 Rev. B

[A]

[B]

Image Area

Desired Image Size (4:3) Clearance Required to Top of Image

Projector Model Height Width Diagonal From Ceiling[A]

From Bottom of Cover [B]

SCP712

36–39" (0.91–0.97 m) 48–52" (1.22–1.30 m) 60–65" (1.52–1.62 m) 19.00" (483 mm) 5.61" (143 mm)

39–42" (0.97–1.07 m) 52–56" (1.30–1.42 m) 65–70" (1.62–1.78 m) 19.27" (489 mm) 5.88" (150 mm)

42–45" (1.07–1.15 m) 56–60" (1.42–1.53 m) 70–75" (1.78–1.91 m) 19.55" (497 mm) 6.16" (156 mm)

45–48" (1.15–1.22 m) 60–64" (1.53–1.62 m) 75–80" (1.91–2.03 m) 19.82" (503 mm) 6.43" (163 mm)

SCP715/717

36–39" (0.91–0.97 m) 48–52" (1.22–1.30 m) 60–65" (1.52–1.62 m) 18.64" (473 mm) 5.25" (133 mm)

39–42" (0.97–1.07 m) 52–56" (1.30–1.42 m) 65–70" (1.62–1.78 m) 18.98" (482 mm) 5.59" (142 mm)

42–45" (1.07–1.15 m) 56–60" (1.42–1.53 m) 70–75" (1.78–1.91 m) 19.33" (491 mm) 5.94" (151 mm)

45–48" (1.15–1.22 m) 60–64" (1.53–1.62 m) 75–80" (1.91–2.03 m) 19.67" (500 mm) 6.28" (160 mm)

SCP716

36–39" (0.91–0.97 m) 48–52" (1.22–1.30 m) 60–65" (1.52–1.62 m) 17.64" (448 mm) 4.18" (106 mm)

39–42" (0.97–1.07 m) 52–56" (1.30–1.42 m) 65–70" (1.62–1.78 m) 17.91" (455 mm) 4.45" (113 mm)

42–45" (1.07–1.15 m) 56–60" (1.42–1.53 m) 70–75" (1.78–1.91 m) 18.19" (462 mm) 4.73" (120 mm)

45–48" (1.15–1.22 m) 60–64" (1.53–1.62 m) 75–80" (1.91–2.03 m) 18.42" (468 mm) 5.00" (127 mm)

Desired Image Size (16:10)

SCP740

29–32" (0.74–0.81 m) 47–51" (1.19–1.23 m) 55–60" (1.40–1.52 m) 22.13" (562 mm) 8.74" (222 mm)

32–34" (0.81–0.86 m) 51–55" (1.23–1.40 m) 60–65" (1.52–1.62 m) 22.82" (580 mm) 9.43" (240 mm)

34–37" (0.86–0.94 m) 55–59" (1.40–1.50 m) 65–70" (1.62–1.78 m) 23.53" (598 mm) 10.13" (257 mm)

37–40" (0.94–1.02 m) 59–64" (1.50–1.63 m) 70–75" (1.78–1.91 m) 24.21" (615 mm) 10.82" (275 mm)

Note: This document is for reference purposes only. Always refer to the installation instructions packaged with the system.

3M™ SCP Screen Size Chart

Note: A & B distance is measured from Top of Image.(Not top of screen)

Top of Screen

Top of Image

12 of 48

Mobile Interactive Solutions

Wall Mount Application Drawing

13 of 48

InstallationEinrichtenInstallazione

3M™ Annotation Sensor Kit

3M Austin CenterBuilding A148-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M CanadaP.O. box 5757 London, Ontario N5V 3R6

3M Mexico, S.a. de C.VApartado Postal 14-139 Mexico, D.F. 07000 Mexico

3M EuropeBoulevard de l'Oise 95006 Cerge Pontoise Cedex France

Please recycle. Litho in USA

3M 2008. All Rights Reserved. 78-6971-1416-9 (3/2008)14 of 48

Tools needed for SCP 712 install:

Step Ladder

1/2" Hammer Drill Motor, 1/2" Masonry Drill Bit and 3/16" Regular Drill Bit

Flat Blade Screwdriver Small Side Cutter Set Small Pliers Set #2 Philips Screwdriver

Minimum of five 3” wire ties Minimum of five adhesive backed wire tie anchors

15 of 48

Tools needed for SCP 712 install, continued

12’ tape measure and Small Level

Small Socket Set (1/4” to 1/2” range sockets)

Hollow wall (Drywall) Stud Locator

78-6971-1420-1 Wall Mount Bracket Installation Instructions (if bracket is being used)

78-6971-1422-7 Folding Mount Installation Instructions - or - 78-6971-1421-9 Fixed Mount Installation Instructions (depending on product SKU)

16 of 48

3M™ Folding Wall Mount SCPFWMV2 and SCPFWMSV2For use with 3M™ Super Close Projection SystemInstallation Instructions

March 200978-6971-1458-1

17 of 48

2 © 2008 3M. All Rights Reserved.

3M™ Folding Wall Mount SCPFWMV2 and SCPFWMSV2

18 of 48

© 2008 3M. All Rights Reserved. 3


Safety InstructionsPlease read and follow all safety information contained in these instructions prior to installation and use of the folding or fi xed wall mounts. Retain these instructions for future reference.

Intended Use

The folding wall mount is intended to provide wall mounting of the 3M™ Super Close Projection System SCP700 Series projectors to the wall as described in the Installation Instructions. It is expected that all installers and users be fully aware of safe operation of this product. Other applications have not been evaluated by 3M and may lead to an unsafe condition.

Explanation of Signal Word Consequences

WARNING: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury and/or property damage.

CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury and/or property damage.

Summary of device labels containing safety information

Caution: Pinch Hazard

Warning: Do not hang on the product

Attention: Read Accompanying Documentation

Caution: Hot Surface

Warning: Do not look into the projector lamp

WARNINGTo reduce the risk associated with all applicable hazards:

Installation Instructions and Product Safety Guide prior to installing, using or servicing the wall mount. Retain these instructions for future reference.

To reduce the risk associated with choking:

materials.

To reduce the risk associated with impact:

installation instructions for details).

is properly reinforced.

mounted projector around children.

of the wall mount.

Projection System SCP700 Series projectors only. It has not

tightened and that no damage has occurred. Repair or replace all issues found prior to further use.

mounting.

mounting.

19 of 48

© 2008 3M. All Rights Reserved.


WARNINGTo reduce the risk associated with hazardous voltage:

found prior to further use.

prior to any servicing.

To reduce the risk associated with fire:

other source of direct heat energy.

CAUTIONTo reduce the risk associated with pinch points:

pinch point injury.

To reduce the risk associated with lifting:

wall mounts per the Installation Instructions due to weight and handling concerns.


SAVE THESE INSTRUCTIONS

20 of 48



Kit Contents1.0Installation Instructions

USB Cable 4m

VGA Cable 4m

6x Cable ties

3x M6*25 Screws (for mounting projector)

2x 1-1/2" Lag Bolts

2x ½" Lag Anchors

2x 2-1/2" Lag Bolts

2x 1-1/2" Lag Anchors

SCPFWMMSV2 Only1.8 m PC Audio Cable

3 m PC Audio Cable

Power Supply for Speaker Amp

Power Cord for Speaker Amp

EU to UK power outlet adapter (EU/UK only)

DC Power Cord (power from I/O to Speaker Amp)

Optional Accessories2.03M™ Wall Mount Bracket (78-6969-9962-8)

3M™ Wall Mount Bracket Security Cable (78-6969-9961-0)

Remove the Cover3.0Remove the Folding Wall Mount from the packaging 3.1and set base-down on a table.

Swing the arm up until it locks in place.3.2

Using a Phillips (+) screwdriver, remove the three 3.3screws holding the cover to the base.

Lift the cover off the base and set aside.3.4

Route Cables4.0Feed the USB, VGA, and optional control cables 4.1through the arm. Align the cable ends and secure about 6 inches (150 mm) from the end using a cable tie.

~6"(150 mm)

21 of 48



Align the cables alongside the power cable and 4.2 secure using cable ties.

Solid Wall Installation5.0 (For Concrete Block or Stud Walls, Skip to Step 7)

Determine desired size and location of projected 5.1 image and mark the location of the top and center of the image.

Locate the “top of image” line of the template for 5.2 the desired image size and then align “top of image” and “image center line” lines with the location of the desired image size. Then mark the positions of the template’s four cross-hairs on the wall.

Image Area

3M™ FoldingWall MountMounting Template

For use with:

SCP715, SCP717,

SCP740

SCP715, SCP717

SCP740

Using the appropriate bit, drill 4 holes for the 5.3 mounting lag bolt anchors. Install the short anchors in the upper holes, and the long anchors in the lower holes.

Note: Use a 1/2” masonry drill bit for solid concrete walls or a 3/16” drill bit for wood walls. Do not use anchors for wood walls, only use screws.

Using a 3/8” socket, install the 2 short (upper) 5.4 mounting lag bolts, leaving 1/2” (13 mm) of the screw protruding from the wall. Do not install the long (lower) lag bolts.

1/2"(13 mm)

Attach to Wall6.0 Hang the wall mount base on the mounting lag bolts. 6.1 Using a 3/8" socket, tighten the mounting lag bolts securely.

22 of 48



Install the long mounting lag bolts through the 6.2 leveling screws and tighten securely.

Skip to Step 9.6.3

3M7.0 ™ Wall Mount Bracket Installation(For Use With Concrete Block or Stud Walls)


Align template with mounting holes in bracket and 7.2 secure to bracket with tape.

Locate the “top of image” line of the template for 7.3 the desired image size and then align “top of image” and “image center line” lines with the location of the desired image size. Mark positions for four mounting holes according to the next step.

Image Area


For use with:

SCP715, SCP717,

SCP740

SCP715, SCP717

SCP740

Align with holesin bracket

Concrete block walls:7.4

Mark the hole positions in the vertical joints between the concrete blocks and then using a 1/2" (13 mm) bit, drill 4 holes 1-5/8" (41 mm) deep into the vertical joints between the concrete blocks. Install 4 long anchors in the holes.

CAUTIONTo reduce the risk associated with impact:

short lag anchors.

16 in

(406 mm)

4X LONG

Stud walls:

Mark the holes at the center of the studs and then using a 3/16" (5 mm) bit, drill 4 holes 1-1/2" (38 mm) deep through the wall into the studs.

4X

1/2–5/8"(13–16 mm)

23 of 48



Using a 3/8" socket, attach the bracket to the wall 7.5using 4 short mounting lag bolts.

Attach Wall Mount Base to Bracket8.0Using a screwdriver, install the two short mounting 8.1screws with washers in the mounting bracket leaving 1/2” (13 mm) of the screw protruding from the bracket. Do not install the long (lower) mounting screws yet.

2X

Hang the wall mount base on the mounting screws. 8.2Using a screwdriver, tighten the mounting screws securely.

Install the long mounting screws through the leveling 8.3screws and tighten securely.

2X

Install Security Kit (Optional)9.0Attach the optional security cable by either locking 9.1it to the mounting bracket security slot (1), looping it through the mounting bracket (2) or looping it through the screw-mount anchor point (3).

1 2 3

Note: If using the screw-mount anchor point, secure the anchor point before attaching the cable.

Feed the security lock cable through the arm. Secure 9.2about 6 inches (150 mm) from the end of the existing cable bundle using a cable tie.

~6"(150 mm)

24 of 48



Route the security cable alongside the bundled cables 9.3and attach using cable ties.

Connect Power Extension Cable10.0Connect the power extension cable as shown. Secure 10.1with cable ties.

Connect Audio Cables 11.0(SCPFWMMSV2 only)Connect the power and audio cables to the 11.1connections inside the cover.

Power Audio

Slide the cover over the arm. Attach the power and 11.2audio cables to the existing cable bundle using a cable tie. Leave 10–12” (250–300 mm) slack cable.

10–12"(250–300 mm)

Attach Cover12.0Attach the cover to the base.12.1

WARNINGTo reduce the risk of hazardous voltage:

25 of 48



Attach Projector13.0Using two screws and the thumbscrew, attach the 13.1mounting bracket to the end of the arm extensionas shown.

Note: First tighten Phillips head screws snuggly onto the ball swivel and then turn thumbscrewto tighten the clamp onto the ball.

Attach the projector to the mounting bracket with 13.2three screws.

Note: Some Models will require two washers per screw to ensure a tight fit.

Assemble Arm Extension14.0Lift the assembly and feed the bundled cables 14.1through the open end of the arm extension.

Insert the arm extension into the arm as shown.14.2

Install the 2 screws into the arm retainer.14.3

26 of 48



Pull the cable bundle through the hole at the end of 14.4the arm extension.

Connect the cables to the projector according to the 14.5Quick Start Guide.

Attach the optional security cable to the projector.14.6

Align Projector15.0Power on unit and change image size by adjusting the 15.1arm extension in or out.

Adjust projector aim by loosening the thumb screw.15.2

Adjust vertical image position by removing the cover, 15.3loosening the lower mounting lag bolts or mounting screws, and adjusting the leveling screws. Tighten the lower mounting lag bolts or screws when finished, and replace the cover.

To adjust horizontal image position: 15.41. Remove the cover. 2. Loosen the adjustment and locking screws. 3. Move the arm left or right to the desired position. 4. Tighten the adjustment and locking screws to secure the arm in the new position. 5. Replace the cover when finished.

Adjustment Screw

Locking Screw

27 of 48

Important Notice

guaranteed.use.

Warranty; Limited Remedy; Limited Liability.

practice or custom or trade usage.

Projector Systems

6801 River Place Blvd.Austin, TX 78726800 328 1371www.3M.com/meetings

Please Recycle. Printed in USA.© 3M 2008. All Rights Reserved.78-6971-1458-1

28 of 48

Mobile Interactive Solutions Div.

3M™ Fixed Wall Mount SCPFXWMV2For use with 3M™ Super Close Projection SystemInstallation Instructions

March 200978-6971-1464-9

29 of 48


3M™ Fixed Wall Mount SCPFXWMV2

30 of 48



Safety InstructionsPlease read and follow all safety information contained in these instructions prior to installation and use of the folding or fi xed wall mounts. Retain these instructions for future reference.

Intended Use

The folding wall mount is intended to provide wall mounting of the 3M™ Super Close Projection System SCP700 Series projectors to the wall as described in the Installation Instructions. It is expected that all installers and users be fully aware of safe operation of this product. Other applications have not been evaluated by 3M and may lead to an unsafe condition.

Explanation of Signal Word Consequences

WARNING: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury and/or property damage.

CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury and/or property damage.

Summary of device labels containing safety information

Caution: Pinch Hazard

Warning: Do not hang on the product

Attention: Read Accompanying Documentation

Caution: Hot Surface

Warning: Do not look into the projector lamp

WARNINGTo reduce the risk associated with all applicable hazards:

Installation Instructions and Product Safety Guide prior to installing, using or servicing the wall mount. Retain these instructions for future reference.

To reduce the risk associated with choking:

materials.


installation instructions for details).

is properly reinforced.

mounted projector around children.

of the wall mount.

Projection System SCP700 Series projectors only. It has not

tightened and that no damage has occurred. Repair or replace all issues found prior to further use.

mounting.

mounting.

31 of 48



WARNINGTo reduce the risk associated with hazardous voltage:

found prior to further use.

prior to any servicing.

To reduce the risk associated with fire:

other source of direct heat energy.

CAUTIONTo reduce the risk associated with pinch points:

pinch point injury.

To reduce the risk associated with lifting:

wall mounts per the Installation Instructions due to weight and handling concerns.


SAVE THESE INSTRUCTIONS

32 of 48



Kit Contents1.0 Installation Instructions

USB Cable 4m

VGA Cable 4m

3x M6*25 Screws (for mounting projector)

4x 1-1/2" Lag Bolts

4x ½" Lag Anchors

Optional Accessories2.0 3M™ Wall Mount Bracket (78-6969-9962-8)

3M™ Wall Mount Bracket Security Cable (78-6969-9961-0)

Solid Wall Installation3.0 (For Concrete Block or Stud Walls, Skip to Step 4)


Locate the “top of image” line of the template for 3.2 the desired image size and then align “top of image” and “image center line” lines with the location of the desired image size. Then mark the positions of the template’s four cross-hairs on the wall.

Image Area


For use with:

SCP715, SCP717,

SCP740

SCP715, SCP717

SCP740

Using the appropriate bit, drill 4 holes for the 3.3 mounting lag bolt anchors. Install the short anchors in the holes. Do not install the lag bolts at this time.

Note: Use a 1/2” masonry drill bit for solid concrete walls or a 3/16” drill bit for wood walls. Do not use anchors for wood walls, only use screws.

Skip to Step 5.3.4

3M4.0 ™ Wall Mount Bracket Installation(For Use With Concrete Block or Stud Walls)


Align template with mounting holes in bracket and 4.2 secure to bracket with tape.

Locate the “top of image” line of the template for 4.3 the desired image size and then align “top of image” and “image center line” lines with the location of the desired image size. Mark positions for four mounting holes according to the next step.

Image Area


For use with:

SCP715, SCP717,

SCP740

SCP715, SCP717

SCP740

Align with holesin bracket

Concrete block walls:4.4

Mark the hole positions in the vertical joints between the concrete blocks and then using a 1/2" (13 mm) bit, drill 4 holes 1-5/8" (41 mm) deep into the vertical joints between the concrete blocks. Install 4 long anchors in the holes.

CAUTIONTo reduce the risk associated with impact:

short lag anchors.

16 in

(406 mm)

4X LONG

33 of 48



Stud walls:

Mark the holes at the center of the studs and then using a 3/16" (5 mm) bit, drill 4 holes 1-1/2" (38 mm) deep through the wall into the studs.

4X

1/2–5/8"(13–16 mm)

Using a 3/8" socket, attach the bracket to the wall 4.5using 4 short mounting lag bolts.

Route Cables5.0Feed power, VGA and USB cables through the base 5.1section of the arm. Bundle the cables and secure about 6 inches (150 mm) from the end using a cable tie.

~6"(150 mm)

Install Security Kit (Optional)6.0Attach the optional security cable by either locking 6.1it to the mounting bracket security slot (1), looping it through the mounting bracket (2) or looping it through screw-mount anchor point (3).

1 2 3

Note: If using the screw-mount anchor point, secure the anchor point before attaching the cable.

Feed the security lock cable through the arm. Secure 6.2about 6 inches (150 mm) from the end of the existing cable bundle using a cable tie.

~6"(150 mm)

Mount Base to Wall7.0Position the wall mount over the mounting screw 7.1anchors or mounting bracket. Install and tighten the 4 mounting screws/mounting lag bolts firmly.

34 of 48



Attach Projector8.0Using two screws and the thumbscrew, attach the 8.1mounting bracket to the end of the arm extension as shown.

Assemble Arm Extension9.0Lift the assembly and feed the bundled cables 9.1through the open end of the arm extension.

Insert the arm extension into the arm as shown.9.2

3M 2008. All Rights Reserved.

Note: First tighten Phillips head screws snuggly onto the ball swivel and then turn thumbscrewto tighten the clamp onto the ball.

35 of 48



Install the 2 screws into the arm retainer.9.3

Pull the cable bundle through the hole at the end of 9.4the arm extension.

Connect the cables to the projector according to the 9.5Quick Start Guide.

Attach the optional security cable to the projector.9.6

Align Projector10.0Power on unit and change image size by adjusting the 10.1arm extension in or out.

Adjust projector aim by loosening the thumb screw.10.2

Adjust vertical image position by turning the leveling 10.3screw.

Adjust horizontal image position by loosening the 10.4four mounting screws and adjusting the base left or right. Tighten the mounting screws when finished.

36 of 48



37 of 48

Important Notice

guaranteed.use.

Warranty; Limited Remedy; Limited Liability.

practice or custom or trade usage.

Projector Systems

6801 River Place Blvd.Austin, TX 78726800 328 1371www.3M.com/meetings

Please Recycle. Printed in USA.© 3M 2008. All Rights Reserved.78-6971-1464-9

38 of 48

Mobile Interactive Solutions Div.

3M™ I/O Module SCPI/OV2Mounting Template 架置模板土台のテンプレート

© 2008 3M Company.

1 1/2"(38 mm)

3/16" (5 mm)

A

1 2

B

No. 4-8 - 3/4" No. 6 - 3/4"

78-6969-9984-2

8 15/16"227 mm

5 3/16"132 mm

2"(25 mm)min.

39 of 48

A/C Power

Service Computer/Component

Control

3M™ Super Close Projection System SCP716

USB Ethernet Computer 1/ Component 1

Computer Out S-Video L SteroMini 1

Computer 2/Component 2

AudioPower Serial RS Video R

RCA Audio

StereoMini 2

AudioOut

USB Ethernet Computer 1/ Component 1

Computer Out S-Video L StereoMini 1

Computer 2/Component 2

AudioPower Serial RS232 Video R

RCA Audio

StereoMini 2

AudioOut

USB USBTo Projector

Control Signal

AudioPower

AudioOut

100–240 VAC50–60 Hz

40 of 48

Installation Checklist Check One Description .

Yes No Was screen or whiteboard previously installed?

Yes No If not has projection area been defined and clearly marked with masking tape for future installation?

Yes No Has projector been installed?

Yes No Was the Accessory Wall Mount Bracket used?

Yes No Has the I/O module been installed (if required)?

Yes No Was the Annotation pod installed (if required)?

Yes No Have the cables been neatly secured and routed?

Yes No Has the projector been properly aligned to project a square image on the screen?

Yes No Has the Annotation Software been loaded onto the meeting room PC and the CD been provided to the customer?

Yes No Did the Annotation Software launch and recognize the attached Annotation pod?

Yes No Has the system been calibrated to the expected screen size and position?

Yes No Have the following tasks been performed successfully using the Annotation Pen? 1. Open eBeam Scrapbook file (requires PC mouse selection for first launch) and make

full screen using pen (maximize the window) 2. Test APPLICATION Icon in top left corner (Figure 1) 3. Test FILE menu item (Figure 2)

See Figures 1, 2, 3 on following pages. 4. Test MINIMIZE icon (top right) (Figure 3 )

5. Test RESTORE icon (top right) (Figure 3) 6. Test CLOSE icon (top right) (Figure 3) 7. Exit 3M Digital Annotation software (close software)

Yes No Have the tools been put away and the installation site cleaned? 1. Have packaging materials been removed? 2. Has it been suggested to keep the projector packaging and box should the need arise

to return the projector? 3. Has the availability of training via teleconference through contacting the Call Center

(1-800-328-1371) been discussed? Yes No Has this checklist been reviewed with the customer for any additional actions needed

(please ask they sign below)?

Please explain any “No” answer: ________________________________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________

I accept the installation.

____________________________ ________________________ ___________ Signature Title Date

41 of 48© 3M 2008. All Rights Reserved.

Installation Checklist (continued)

FIGURE 1

Application Icon

Application Menu

FIGURE 2

File button

File menu


Installation Checklist (continued)

FIGURE 3

Minimize

Restore

Close

43 of 48

37 of 48


SCP Installation Notes and Tips Accessory Wall Bracket

Notes: • Recommended for mounting either 3M™ Fixed or Folding Wall Mount units to concrete block or

hollow wall applications. • Easier to position the projector above screen for best image results. Tips: • Use the Template provided with the 3M™ Wall Mount kit to correctly position the wall mount

bracket over the whiteboard. Note: When correctly positioned, the wall mount is slightly off center from the centerline of the whiteboard or projection screen.

• Plan installation accordingly. If the whiteboard is already installed, then determine the center of desired image area on the whiteboard. Use this image area centerline reference and the template to determine the bottom location of the mounting bracket. This technique will position the wall mount to project an image that fills the defined/desired screen area.

• Align bracket holes over studs in hollow wall. Mark and drill holes into studs to secure the bracket to the wall. Attach Wall Mount and align to image area centerline reference.

• For cinder block or brick wall applications align bracket holes with mortar seams between the bricks or blocks. This will make it easier to drill the holes for the lag bolts. Attach Wall Mount and align to image area centerline reference.

Folding or Fixed Wall Mount Bracket: Tips: • Remember to install the I/O module control cable per the instruction prior to hanging the Wall

Mount. • Use the Template provided with the Wall Mount kit to correctly position the wall mount bracket

over the whiteboard. Note: If the whiteboard is too close or far from the bottom of the wall mount, there may be image distortion from keystoning.

• Tighten the ball clamp screws in the ball joint mounting bracket first before tightening the clamp onto the ball with the long plastic thumbscrew.

• For Folding Mount with Speakers, make all of the connections then power on the device. Do not apply power to audio power supply until it is connected to the amplifier in base. Do not plug speakers into active (powered on) audio sources.

Whiteboard or Screen: • Determine the desired location for the whiteboard or projection screen and use the template to

verify there is enough height above the desired screen location to properly install the Wall Mount. • After mounting the whiteboard or projection screen, use the Template provided with the Wall

Mount kit to correctly position the wall mount bracket. Note: If the whiteboard/screen is too close or far from the bottom of the wall mount, there will be image distortion from keystoning.

I/O Module: • Version 1 I/O modules only operate the Computer Out Port when the Projector is illuminating an

image. If operation is desired when the projector is in standby mode, then a splitter or selector switch for the attached monitor is required.

• Version 2 I/O modules and afterward are pass through on the Computer Out port and do not need any additional equipment to operate an attached monitor while the projector is in standby mode.

• For best results, the projector should be attached to the USB Port farthest from the Audio Power output jack (refer to 3M™ Operator’s Guide & 3M™ Quick Start Guide).

• For best results, the Annotation or other devices should be attached to the inner USB Port (refer to 3M™ Operator’s Guide & and 3M™ Quick Start Guide).


Annotation Pod: • Pen skips are caused by signal reflections (interference) from raised surfaces near the borders of

the screen surface. To prevent pen skips, insert a 1/2 inch round molding at the raised edge. The edge of the molding will stop unwanted signal reflections.

Add ½ round molding beneath the cork pin up railing along the top of the board. The edge of the molding will stop unwanted signal reflections that cause the pen to skip.

• Pens not detecting any signal. This problem can be caused by general room interference, poor batteries, a defective pen or a bad microphone on the pod.

• If the pen is not being detected in the top portion of the screen, the Pod ID/icons reserved for the right side of the board may be a problem. This can be corrected by changing the pod product ID using the Product ID updater program. Contact Call Center at 1-800-328-1371 for details.

• Pods must be placed with the top microphone parallel to the top of the image and the side microphone parallel to the edge of the image. Misalignment of the pod will cause pen detection errors in the upper quadrant.

• The nearest upper corner of the image must be 5 inches from the center of the LED (3M logo) and 1 inch beneath the top microphone.


Image and Keystoning Issues While keystone correction is a handy feature for portable projector users, it does not produce an ideal picture quality. Scaling inside the projector creates a slightly distorted image, particularly at the sides of the screen. Therefore, the installer should always try to manually position the projector to have the squarest image possible. The best picture will always be from a projector that has not had its keystoning adjusted.

Super Close Projectors (SCP) The 3M™ Super Close Projectors present a different perspective to keystoning issues. The projected image is already at an extreme angle. However, the lenses inside the projectors compensate the projected image so it should still be square on the screen.

Tabletop: Position the projector perpendicular to the screen. The projector should be placed at approximately the same level as the bottom of the image or the bottom edge of where you want the image to start. Wall-Mounted: Use the installation template to correctly position the wall mount over the screen. It should not be centered over the screen due to the projector offsets and keystone adjustment. Adjust the image to be square and then extend the arm to fill the screen area. Most problems can be fixed with adjustments to the wall mount or the screen position.

Adjust for Square Image 1. Push the arm all the way in to get the smallest image. 2. Use the ball joint to get a perfectly square image. Ignore whether or not the image is on the board.

The key is getting it square and then tighten down the ball joint mount bracket. 3. Pull the arm out until the sides of the image match the sides of the board. 4. Use the feet of the wall mount to adjust up or down to get the vertical alignment correct. After you

adjust the feet, eliminate any keystone by re-adjusting the projector at the ball joint mount bracket.


47 of 48

3M MISD Fixed & Folding Wall Mount Pre-Installation...

Documents

Transcript of 3M MISD Fixed & Folding Wall Mount Pre-Installation...