3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
-
Upload
joshi-thomas -
Category
Documents
-
view
263 -
download
1
Transcript of 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
1/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
1
USER MANUALFor 3D Touch Interactive Whiteboard
(Version 3.3 N))
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
2/21
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
3/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
3
Introduction
3D Touch Interactive Whiteboard is attached with Projector/LCD and turns any flat surfaces into interactive and
collaborative workspace. It is an inexpensive Interactive Solution.
Key Features
1, Portable, Reliable, Simple installation;
2, Automatic Calibration within 4 seconds;
3, Screen Size is not limited, Support up to 150;
4, Turns LCD Screen into Interactive Whiteboard;
5, Multi Touch. Two or more users can write on it at the same time
Specifications
Active screen area 40- 150''diagonal
Shipping size 25 cm 26 cm 7 cm
Shipping weight 0.5 kg
Technology Optical + Laser technology
Mouse Function Double click function. Right-click function can be
achieved by maintaining the pressure on the board for
2 seconds.
Power Energy is taken from a computer via a USB cable.
Power Consumption 1w.
Delay Time
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
4/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
4
Package Includes
Calibration Device 12m USB Cable CDs
Infrared Pen Ceiling Mount Pointer (Optional)
Battery size for infrared pen/ Pointer: 2 pieces, AAA (non included)
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
5/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
5
Hardware Installation
Install Calibration Device
Install the Calibration Device to the ceiling with the mount and the distance to the front of the projection screen /
surface (based on 80 Projection Screen) should be approximately 1m for Short Throw Model.
Note:For 80 active size (Projection screen), the installation distance is about0.45 m-0.8m for ultra short throw
Sensor part, and about 2.2m-3.2m for long throw Sensor part.
Pic 1
Turn LCD TV screen into interactive: Connect the computer with the LCD TV through VGA cable and then
follow the following steps.
Connect Calibration Device
Connect the Calibration Device to the Computer (Laptop) with USB Cable. (Plug USB Cable into one of back
ports of computer. For Laptop, extra power may beneeded
Please note: If there is already a Video Camera/Webcam in the computer/Laptop, please disable it
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
6/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
6
Calibration Software
Introduction
1. Operate menu list
Pic1
Operate Menu list including run, stop, parameter settings, Auto Mask Clutter, Manual Mask Area, Manual
Calibration, Automatic Calibration, Disable the optical pen control and Exit.
(1) Parameter setting: almost parameter of the calibration software here, such as Proportion of the
spot, Eraser in multiples of spot, Brightness coefficient, Auto calibrate average brightness.
(2) Auto mask clutter: chose it, then software will mask the bright spot automatic.
(3) Manual mask area: manually mask the bright spot.
(4) Manual calibration: there are two kind of manual calibration, 25point and 36point.
(5) Automatic calibration: automatically make the calibration.
(6) Disable the optical pen: chose it, then you disable of function of the pen or finger, so you cannot
use the pen or the finger any more. Usually when the mouse out of control before the calibration, then
you can chose it.
(7) Exit: mean you wan not use the software and exit it.
Note: in the top right corner, which is not mean exit the software, it is mean you close display on
window, but the software will be there (bottom right corner)
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
7/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
7
2. Parameter Setting(As Pic6)
Pic 2
(1), Set the proportion of the spot (20%~80%): to set how large the spot will cause the sensor to detect. ( No
mean for pen touch model)
(2), Eraser in multiples of spot (3~7): set how large the spot will appear eraser. (No mean for pen touch model)
(3), Normal use of the brightness coefficient (0~250): adjust the average brightness of the software interface
when the device works normally.
Note: when you adjust this data, you should restart the software.
(4), Auto calibrates average brightness (0~255): adjust the average brightness of the software interface when
does calibration
(5), Auto calibrate light gray (0~255): when calibration failed, and the projection screen is very gray, then you
can adjust this data (increase) , when the projection is very brighten, then decrease.
(6), whether to record video: to record the auto calibration video.
(7), There are three model for usage, the pen touch, the finger touch and the rear projector.
(8), Manual Collection spot: when you writing, it interrupts, then do it (As Pic3)
(9), Default settings, click it; all parameter will be recommended value.
Pic 3
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
8/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
8
Pic7
3. Installation and debugging
(1). Show Status: check frame rate and real-time frame rate of the camera. If the frame rate lower than 110fps,
then you should check if there any problem.
(2). Tuning webcam image mode: chose this mode before calibration, then you can see the screen more clearly
and then adjust the position of camera.
(3). Tuning laser transmitter image mode:( No mean for pen touch model)
(4).Normal Usage image mode: after calibration, then use this mode to check the image. (After you calibration,
then you can see the image in normal mode).
4. Help
(1) Language option: chose the language as you like.
(2) About: company and software information
5. Right click the minimized software menu
Pic 4
(1) Display the main windows: display the interface of the calibration software
(2) Coordinate calibration: not use this option for now.
(3)Auto run at system startup: chose it, the software will be start when the computer starts.
(4) Exit: Exit the software.
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
9/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
9
Calibration
Step 1: Place the small software CD-ROM into the CD drive and copy the Calibration Software and IWB
Application Softwarefolder in the CD-ROM onto your PCs hard disk drive.
Please Note: do not RUN the software from the CD.
Step 2: Open the file of Calibration Software, run IWB_Setup.exe; , Then there will be icon
on desk :
Step3: Please click Installation and debugging-Mode 1. Then you will see the screen as below. You can see
the projection screen clear from calibration software window.
Projection screen image
Pic5
Note: make sure all projection screens image are included in the calibration software intersurface. The
image should take over 50% to 80% of the software screen.
Software interface
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
10/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
10
Pic 6
Next, keep adjusting the location or angel of calibration device or move any strong light until there is no
green dot or area in the viewing window. Please note: If there is any green area in this calibration
software screen or calibration will not success.
Step 4:
Option 1: Automatic calibration:
Just click Operation, chose Automatic Calibration, then you will see as below:
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
11/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
11
Pic7
About 4 seconds, its finished.
Option 2:Manual Calibration
1, Please choose Auto Mask Clutterfrom Operationor you can pressCtrl+Shift+A. The software will
specify the active area automatically. The other area will be shielded by green mask.
Pic 8
2, Touch each corner and check if it can be seen from the calibration screen like below. If some corner is notincluded, please eraser the green mask (Mask Bitmap Edit-Erase Mask Area).until you can see the spot as
below
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
12/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
12
Pic 9
Pic 10
3, Click Manual Calibrationin the Operation.
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
13/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
13
Pic11
You enter the calibration process now. Please use Pen to click the center of the cross on the screen, finished one,
then another cross appear, repeat this until the 36th dot or 25thdot is finished.
Pic 12
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
14/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
14
After Calibration finished, Viewing Window will be minimized in the right corner of the computer.
To make the device run with system start. Please right click the Icon . And select Auto Run At System
Startup
l
Tip: No need to calibration again when the projector and signal device are not moved.
Now you could control the computer from the projection screen with the infrared pen.
Pic 13
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
15/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
15
Application Software Installation
Step 1: When system is Windows Vista or XP, please place the big software CD-ROM into the CD drive and copy
the DotNetFX35 folder in the CD-ROM onto your PC s hard disk drive. (Please skip this step with
Windows 7)
Please Note: do not RUN the software from the CD.
Step 2: Open the DotNetFX35and then run .
Step 3: Open the folder IWB Application Softwareand run , Chose the install path and
language, then click next stop to install GLboard, then you will see :There will be a icon of GLboard
on the desktop.
Now the Application software of GLboardis installed.
GLBoard Software Manual
Introduction of the main toolbar
When you use the GL Board at first time, double click
To pen the software, interface includes three areas as following:
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
16/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
16
Function of Each button in the tool bar
iron Name function
Start menu Open the menu list
Resource Local recourse: You can click it to find many pictures.
Network resource: you click it and then you can search
any picture as you like.
New page There are four options:
back Go back to the previous page
forward Forward to next page
Pen Write like a ball pen
brush Write like Chinese brush pen
Smart pen Convert the drawing to typewriting geometric shapes.
Operate area: picture or text edit
Toolbar
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
17/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
17
Multi-writing
mode
Support ten persons writing simultaneously. Attention,
when you use this mode which is new function, you
just can write.
Insert shape Several shapes can be chose, such as triangle,
square ,circle and so on
Import picture Insert picture from your computer
Import text Insert text frame, then edit the words
Fill Fill the geometric shapes with different color
Select stroke Select the handwriting on the page, and do drag and
zoom operation
Select picture Move geometric shapes, text and pictures
zoom in and
out
Zoom in or zoom out the picture
Pen color Adjust the any pens color
Fill color Chose the color to fill
Pen width Set stroke width and line type.
Erase Three options:
undo Cancel the last operation
redo Redo the operation just canceled by undo
Move Move the edit screen
windows Back to the desktop
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
18/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
18
Start Menu Introduction
Click the menu , then the tool list will pop up, click the option according to the different needs.
The File menu: including theNew, Open, Save, Save As Support
open PTS, PDF, Word, Excel,
PowerPoint and other file formats.
Insert Hyperlink: including the
Web Page, Disk File and
Documentation Page
Export: the current page could be
exported as the format of PNG, JPG,
BMP, ISF and XPS.
Change Background: used to
change the background of current page.
Tool Group Includes: Protractor,
Triangle, Ruler, Timer, Media Player,
Vide Capture, Mask, Magnifying glass,
Spotlight, Keyboard, Calculator,
Handwriting Recognition, Screen
Recording, External tool Management.Slide page navigation: users will
be required to open the slide and enter
the View Show status under the
desktop status, click on the function keys
then the Annotation, page up and down
could be achieved.
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
19/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
19
Minimize the Toolbar Introduction
Click to switch to the desktop Mode, then the right side of the desktop will appear Minimize toolbar, the
following is a description of each button:
Back to Desktop
Pen
White Page
Previous Page
Erase
Undo
Note Page
Previous Note Page
Black Page
Next Page
Insert Picture
Exit
Pen Size
MaskMagnifying glassSpotlight
Screenshot
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
20/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
20
Tips1. The most proper distance from calibration device to the screen is 55cm - 100cm if the projection screen is
70-80inch. Computer image taken by the device must include whole projection screen. you can open the
menu of Installationand chose tuning image mode 1, then you can see following:
2. When use the infrared pen do manual calibration. Place the pen tip at the center of the cross; hold the infrared
pen at an angle of3045 to the projection surface and then press. Please hold on until color of cross turns
blue from red. Then click next cross.
3, Best Installation way: Install the Calibration Device on the ceiling and there is no block between the tip of pen
The white place is projection
screen shoot by our camera.The white image must take
up 60-80% of total screen.
-
7/26/2019 3D Touch Portable Interactive Whiteboard Manual 3.3.0.0
21/21
3D TOUCH INTERACTIVE WHITEBOARD MANUAL
21
and device. If the Calibration Device cannot be installed on the ceiling, please make sure there is no block
between the tip of pen and the Calibration Device when operation, like users body or hand. If there is block,
interrupted lines would happen during writing.
(Remark: if battery is not available, interrupted lines would happen during writing too.)
4, Operate right click function: pressure the infrared pen for 2 seconds.
5, USB cable has to be plugged into the port in the back of Computer Box.
6, If the software screen is not red, click stop and set another camera in the list of device, then choose start
again.
7. If after calibration, window of software is minimized and the mouse can move, but operations of double-click
and right-click does not work, please check if you have installed any anti-virus software, which prohibits additional
mouse functions, so that you cannot use all the functions of mouse. Please turn off anti-virus software, and then
our software can be used normally.
8, If there is time delay of green light moving in the red screen of the calibration software, please open menu of
status and check actual frame rate. If it is less than 110, please change a computer or contact your seller.
9. If the calibration failed, then you can find the folder named Intermdiate, open it, then you will find folder
namedautocalibrate. This folder record what is happen to the calibration, and then analysis the picture in it, then
you can know why calibration failed. If you dontknow how to analysis, then send such folder to manufacturer or
your dealer.
End