3D Printed Microfluidic Medical Devices: Rapid Prototyping ...
Transcript of 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...
![Page 1: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/1.jpg)
www.veryst.com
3D Printed Microfluidic Medical Devices: Rapid
Prototyping Using LiveLink™ for MATLAB®
Andrew Spann, Ph.D.
Matthew Hancock, Ph.D.
10/5/2017
![Page 2: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/2.jpg)
Outline
There are limitations governing the
ability to scale 3D printed devices
down to the cellular scale
We use LiveLink for MATLAB or
Model Methods to determine the limits
of our 3D printing process
COMSOL Multiphysics simulations
discern the effects of uncertainty in
printing
210/5/2017
![Page 3: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/3.jpg)
Good News: It is Easy to Start 3D Printing
COMSOL Multiphysics can export geometry to 3D printer
Numerous services available where you upload files, get feedback on which
design features are likely too small, and receive prints via mail
Variety of 3D printing technologies to choose from with pros and cons1
For microfluidics, two good options are stereolithography (SLA) and PolyJet
For this talk, we will use SLA and channels will be 1 mm tall
310/5/2017
1For an excellent review, see Waheed, S., Cabot, J. M., Macdonald, N. P., Lewis, T., Guijt, R. M., Paull, B., &
Breadmore, M. C. (2016). 3D printed microfluidic devices: enablers and barriers. Lab on a Chip, 16(11), 1993-2013.
![Page 4: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/4.jpg)
3D Printers Have Limits in Feature Size
I can draw a thin channel
But it may not print!
Resolution of printer
Support material
Drainage
Drainage is a large concern for complex designs
410/5/2017
![Page 5: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/5.jpg)
Strategy for Printing Quickly and Effectively
Find important features in medical device
Break features down into parameterized geometry
Use Livelink with Matlab or Model Methods to create a calibration test grid
and determine what can be printed
510/5/2017
d
2d
w
Increasing d
Increasing w
![Page 6: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/6.jpg)
Grid with d, w in Range(100 μm, 50 μm, 650 μm)
610/5/2017
Incre
asin
g w
Increasing d
![Page 7: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/7.jpg)
Result: Can’t Reliably Print Channels Below 300 μm
710/5/2017
300
μm
250
μm
200
μm100
μm
150
μm
200
μm
Even if we see a faint outline,
channel inside has cured shut
![Page 8: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/8.jpg)
Rotated Grid to Test Printer Orientation Bias
810/5/2017
200 μm 250 μm 300 μm
100 μm 150 μm 200 μm
![Page 9: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/9.jpg)
Incorporating COMSOL Simulation: Post Test
We’ve established there is a gap between
what we specify and the print we receive
How would this affect our flow pattern?
We use Livelink for MATLAB and
COMSOL Multiphysics to perturb the
geometry to see the effect on flow
simulations
910/5/2017
![Page 10: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/10.jpg)
Uncertainty in Geometry
In a perfect world
500 μm post diameter
1 mm distance between post
centers
For our uncertain world, add
Gaussian noise of standard
deviation 50 μm to
Post diameter
Post center x-coordinate
Post center y-coordinate
1010/5/2017
Modular connections omitted
![Page 11: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/11.jpg)
Creeping Flow Streamlines
1110/5/2017
Perfect Geometry
Colored by velocity
Perturbed Geometry
![Page 12: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/12.jpg)
Particle Tracing Visualization
1210/5/2017
Velocity
(m/s)
10000 particles
Diffuse scattering condition
at walls and posts
Perturbed geometry
Not intended as a direct
representation of physical
parameters relevant to
application
![Page 13: 3D Printed Microfluidic Medical Devices: Rapid Prototyping ...](https://reader030.fdocuments.us/reader030/viewer/2022012711/61aad13e5186e51ed8260077/html5/thumbnails/13.jpg)
Summary
COMSOL Multiphysics makes it easy to
realize your designs with 3D printing
Test the limits of your 3D printer using
Livelink for MATLAB or Model Methods
Use Livelink for MATLAB and COMSOL
Multiphysics to ask how simulations can
change under perturbed conditions
1310/5/2017